Graphite BS faster then Airport Extreme BS - Why?

I've tried 2 base stations in my home. Same room, same location, same modem, same computer. My Graphite Airport Base Station pulls a 3.3 mb download and a 1.1 mb upload. My newer Airport Extreme Base Station pulls 1.9 mb download and a 900 kb upload speed. I have no idea why. I've tried reconfiguring different settings but nothing has worked.
What am I doing wrong?
tested on iBook g3 600mhz, 640ram, running 10.4.11.

The newer base stations are optimised for 802.11n. Although they are backwards compatible with 802.11a through g, performance is not as good when compared to an AEBS or AEX of the era. To get around this problem at home I run 2 wireless networks, one for n the other for everything else using respective base stations.

Similar Messages

Netgear faster then Airport Extreme?

I have a 10MB internet connection via a cable modem.
I plug the cable modem into my Netgear Rangemax cable router - Speedtest.net shows I am getting 9.7MB downloads - which is what I expect.
I do exactly the same test (from the same distance etc) with my AEBS, and only achieve around 2MB download?
Why is this??
I do everything the same when connecting - switch everything off, power up the modem, then power up the router, then power up my MBP. Both are at the same distance from my MBP - literally 2 feet away. Yet the Netgear gives me my full speed and the AEBS does not??
My current connection to the AE shows the following:
PHY mode: 802.11n
Channel 36 (5GHz)
Security: WPA2 Personal
RSSI: -53
Transmit Rate: 108 (sometimes this goes up to 300, even though my MBP hasnt moved?)
MCS Index: 15
Why isnt my AEBS giving me my full speed??
It is running the latest 7.4.2 update etc.

Hmmmm, not sure what to make of this!
I entered Airport Utility to double check all settings etc. I didnt change a single setting - I exit the utility and didnt save anything etc.
I ran another speedtest, and as I turned around to grab an ethernet cable to test via ethernet, my speed has shot up to normal - around the 9.5MB mark download!
Im not sure what has caused this - but things seem to be Ok for the moment!!
Any ideas what could have caused this dip in speed?
Pretty sure its not my ISP as it worked fine when I plugged my Netgear back in!

My laptop compaq presario will not connect to the Internet anymore after buying airport extreme. Why? It detects the network, accepts my password, but will not connect to Internet.

My laptop compaq presario will not connect to the Internet anymore after buying airport extreme. Why? It detects the network, accepts my password, but will not connect to Internet. I tried to repair connection, tried to reboot modem several times, I even updated my computer. Nothing. All it says is that it does not detect modem. Why?

Welcome to the support community group.
First, are you sure that your AirPort Extreme has been configured correctly and is properly connected to your modem?
Begin by telling us how you have things connected and if the Airport Extreme is replacing a previously owned router or is this an entirely new installation?
First be sure that your modem is working and properly connects you to the internet using an ethernet cable directly connected to your laptop. Once you're sure that's working, reset the AirPort to factory defaults by disconnecting it from power and pressing and holding in the small reset button on the back for 15 - 20 seconds while you reconnect it to power. Then turn everything off for 5 minutes. Connect the Airport to your modem with and ethernet cable to the Airport WAN port on the back (check the user guide to make sure you connect the cable to the correct port) then connect a second ethernet cable between the laptop and one of the LAN ports on the AirPort Extreme.
Then power up the modem first, wait 5 minutes and then power up the Airport, wait 5 minutes and finally power up your laptop.
Then run the airport configuration utility from your laptop. Since you're not using an Apple computer, be sure that all of your firewall, and virus blocking and checking software is disabled before you run the airport configuration utility. Once you run the utility, it should detect your AirPort and allow you to use the configuration wizard to set things up.
Check back if you're still having problems.

The ethernet ports suddenly stopped working on airport extreme wondering why and how to fix the problem

I use the ethernet cable to connect my airport extreme to a linksys router to extend the network but suddenly all the ethernet cables on airport extreme stopped working and now the linksys won't get a connection. I was wondering why this might of happened and if there is a solution to fix the problem. Also i wondering if i should get rid of the linksys and get and airport express to just extend the network.

The Extreme to Express without the Linksys router is the most compatible way to go but I would first check out the Extreme by itself and make sure everything is working properly

Airport utility asks for password after factory reset of Airport Extreme (spaceship), Why?

Hi, I recently replaced my Airport Extreme (the older model shaped like a space ship, 802.11 b/g) with an Airport Express. I tired to move the spaceship to a different room in my house to extend the wireless network, but it was not being recognized by the Airport Utility (v5.6). So, I did a factory reset of the spaceship. Now I can see it in Airport Utility, however when I try to configure it, the Airport Utility prompts me for a password. It will not accept "public" as the password. Any ideas? Could keychains be the problem? This is a 2009 MBP running 10.8.3.

Great! Thanks for the update.
Out of morbid curiosity I went to my Mountain Lion Mac and downloaded AirPort Utility 5.5.3. I confirmed it will not install on Mountain Lion using OS X's usual package installer, but using the technique that follows I was able to install and run it on Mountain Lion. The only thing I could not verify is its ability to administer an older AEBS since I no longer have any to test.
The remainder of this post is for those who are willing to circumvent Apple's desire to use only current versions of AirPort Utility for reasons known only to them. Proceed only if you accept this as an unsupported workaround strictly for the purposes of administering an older Extreme on a newer Mac.
Prerequisites: A package extractor like Pacifist or unpkg will be required. Pacifist is shareware, unpkg is free.
Download Pacifist here: http://www.charlessoft.com/
Download unpkg here: http://www.timdoug.com/unpkg/
Download AirPort Utility 5.5.3 here: http://support.apple.com/kb/dl1390
Directions for Pacifist (I do not have screenshots for unpkg but the idea is similar):
After the .dmg file finishes downloading double-click it to mount the volume containing the metapackage. Control-click it and select Open With > Pacifist from the contextual menu:
You will get the following dialog:
The "unidentified developer" in this case is Apple. Click Open to open Pacifist.
Click the "reveal triangles" until you see AirPort Utility.app and select it.
The next steps are important.
Select Extract To... from the toolbar as in the above screenshot. In the dialog that follows, choose Desktop since otherwise you will overwrite your existing, newer version of AirPort Utility in your Utilities folder which should not be deleted. Restoring it may not be trivial.
Authenticate, allow Pacifist to extract the app, then you can quit Pacifist.
You will now have AirPort Utility version 5.5.3 on your Desktop. Before you attempt to copy it to your Utilities folder though, be sure to rename it accordingly:
You can then drag it to your Utilities folder. Authenticate, and you will have it alongside later versions where they can peacefully coexist:
Use the newest version AirPort Utility to administer current production AirPort Base Stations, and older versions only as necessary for older AirPort Base Stations that cannot be administered any other way.

I have several questions: 1. When I connect my Iphone using Wi-Fi what can I then do? Why won't my Iphone recognize my home network run off of Airport Extreme, and the app Nike Ipod sensor never activates.

I went to Starbucks this morning and my Wi-Fi on my Verizon Iphone connected, what does this allow me to do? My Wi-Fi does not recognize my home network from which I connect wirelessly to my MacBookPro and to my Apple TV using Airport Extreme router, why? Lastly, what do about the app NIke + Ipod not working. The sensor does not activate even after walking a half mile.

It might be best to ask only one question in each post otherwise you may never be able to mark them as solved.
I went to Starbucks this morning and my Wi-Fi on my Verizon Iphone connected, what does this allow me to do?
It should allow you to access the internet, read mail, etc.
My Wi-Fi does not recognize my home network from which I connect wirelessly to my MacBookPro and to my Apple TV using Airport Extreme router, why?
Try restarting your router (remove power for 30 seconds and restart). It may not be properly assigning an IP address to your iPhone.

New Airport Extreme in Bridge mode -- some devices have no internet access

I just bought a new Airport Extreme as my old one which was probably 7 years old required restarting every day. My setup is as follows: DSL cable modem to Linksys Router (for a long set of convoluted reasons, I can't remove this layer) and then Airport Extreme. This is how I had it set up with my old one. The only difference is I recently started looking into using "Back to the Mac" on MobileMe and in order for it to work, I set my new Airport Extreme to Bridge mode due to dual NAT. I have an iMac, PC, MBP, MBA, iphone 4, AppleTV and ipad. All was working fine last night when I set it up. 24 hours later, for some odd reasons, I can't have my PC accessing the wireless network at the same time. If I did, it would knock my iMac off the network and says some other device is using the same IP address. For a while, only my iMac (my main computer) can access it and even my iphone can't. At this very moment, my iphone, imac and MBP all have access to the wireless network. My MBA and iPad has no internet connection. I've restarted Airport Extreme, Linksys, and modem more than once... If I switch back to "Use Public IP Address" instead of Bridge mode, everything works except for "Back to the Mac"... Help!

Hey Bob, Thanks...I have already repeated that multiple times yesterday and today but to no avail. I tried to get into the Linksys router control panel but unfortunately we can't remember the username and password (the router is not mine). The make things even more complicated, the router is actually part of the internet package provided by the ISP and they use a PPPoE to log in. Theoretically, we could do a hard reset but the problem is the ISP will not release the PPPoE information unless we sign a long and complicated form saying we want to bypass their Linksys router. We can do that but this process will take days and weeks... Our ISP confirmed that the Linksys router is set to max out at 5 DHCP but we can only connect 3 machines at a time. They are coming out to take a look tomorrow but in the meantime I have reset the Airport Extreme to "Distribute a Public IP Address" mode which will allow access to all computers/devices. What's even more weird is that if I did the Bridge mode, it messes up the Linksys router's own network as well. We can't even just sign into that network... Any ideas why?

How do I change airport extreme's network drive permissions?

Hello.
I want all Macs (3) in my house to have read/write access to the network drive connected via Airport Extreme. Why is this difficult?
Here are my current settings:
Here's what I want to change:
What gives?

Unfortunately, Apple offers little in the way of setting permissions with AirPort Disks. You won't be able to set permissions individually for either directories or or files nor set them differently on separate partitions or separate disks.
One option, using the With Accounts option, is that you can specify individual user credentials with different access levels. These accounts would be distinct from OS X or Windows user accounts. However, to use this option, the HD would need to be formatted in HFS+.

Sky Hub (SR101) configured to roaming network on Airport Extreme?

Hi,
Im trying to find out if it is possible to connect a Sky SR101 Hub to a Airport Extreme to create a roaming network with 3 Airport Extremes?
If so is the procedure of connecting it as follows:
1. Sky Hub ethernet port connected to WAN port of 1st Airport Extreme
2. Ethernet Cable from the 1st Airport LAN port to the WAN port of 2nd Airport (in another room)
3. Ethernet Cable from the 2nd Airport LAN port to the WAN port of 3rd Airport (in another room)
What is the best way for the DHCP?
Do I set the 1st Airport that is connected to the Sky Hub do the DHCP and turn the Sky Hub wireless and DHCP off?
I am a bit confused when it comes to the DHCP side.
Thanks for your help in advance.

The Sky SR101 is a modem/router that provides both DHCP and NAT service.
So, in a "roaming network" configuration, each one of the AirPort Extremes would be configured to "create a wireless network" using the exact same wireless network name, same security setting and same wireless password as the Sky modem/router. Each AirPort must also be configured to operate in Bridge Mode.
Here, I am assuming that the Sky SR101 will be creating a wireless signal. Optionally, you could turn off the wireless on the Sky modem/router and use it only as a wired router if you prefer. In this case, the 3 AirPorts would be providing your wireless network.
1. Sky Hub ethernet port connected to WAN port of 1st Airport Extreme
2. Ethernet Cable from the 1st Airport LAN port to the WAN port of 2nd Airport (in another room)
3. Ethernet Cable from the 2nd Airport LAN port to the WAN port of 3rd Airport (in another room)
This will work, but better wiring practice.....if possible.....would be to connect each AirPort directly back to one of the Ethernet LAN <-> ports on the Sky modem/router. This is called "home run" wiring.
The reason for this is that your proposed setup makes use of what is known as a "daisy chain" configuration.
While the "daisy chain" type of setup will work....if everything is working.....let's say that you configure the network as proposed in 1), 2), and 3) above.
If the 1st AirPort Exteme has a problem, it will take out AirPort Extreme 2 and AirPort Extreme 3 as well. Or, if AirPort Exteme 2 has a problem, it will take out AirPort Extreme 3 as well.
With the suggested method of connecting each AirPort directly to the Sky modem/router in a "home run" wiring configuration, you might have a future problem develop with any given AirPort, but this will not affect the operation of the other AirPorts.
As far as DHCP and NAT service, it might be possible to configure the Sky SR101 to operate only as a modem with DHCP and NAT functions disabled.
But, even if you can do this, your service provider may not support this type of setup, so you would want to check with Sky first to see 1) If this is possible, 2) How to do it, and 3) Verify that they will support that type of configuration.
If you decide to go this route, then AirPort Extreme 1 would be configured to provide DHCP and NAT service. AirPort Exteme 2 and AirPort Extreme 3 would still both be configured in Bridge Mode. In this case, you would connect AirPort Exteme 2 and AirPort Extreme 3 directly to AirPort Extreme 1.

4Gen Airport Extreme Firmware 7.6 problems

I installed the 7.6 firmware and started to have some strange problems, they seem DNS related, Most sites work fine but there are a handful of sites and online games that no longer work, I try to goto the game websites such as secondlife.com and the page cant be displayed, i try to ping the site and get a DNS error no such site. I then reverted the extreme back to 7.5.2 and everything is working fine again, I upgrade back to 7.6 and the problem is back, there seems to be some type of DNS routing problem with the 7.6 firmware, has anyone else had similar problems?
P.S. I also noticed that with the 7.6 firmware installed my iphone is no longer able to upload photos to a photo website I use and after going back down to the 7.5.2 firmware the iphone works fine with the photo site.

As you know, this type of setup for Time Machine backups is not supported by Apple.
So, in effect you are asking us for help on a configuration that is not supported. We'll try.
Did you power cycle the entire network?
This would involve powering each device down, waiting a few minutes, starting the modem first, then AirPort Extreme, then hard drives and other devices one at a time about a minute apart.
If you try this a few times with no help, it is very possible that the 7.6 update has further limited the ability to set up Time Machine backups to a drive at the USB port of the AirPort Extreme. We've seen other similar posts from users who are having the same types issues that you are.
If that is the case, the only thing that might help is rolling the firmware back to 7.5.2.

Airport extreme not showing up in airport Untility

My airport extreme is not showing up on my mac in airport utilities, was blinking amber I unplugged it back to green but still not showing up in airport utility

Suggest that you restart the entire network by powering everything off...order is not important...and starting the modem first, then AirPort Extreme, then each device one at a time.
Temporarily, connect a spare Ethernet cable from your Mac to one of the LAN <-> ports on the Time Capsule.
Check to see if AirPort Utility can see the AirPort Extreme
If this works, when you have completed checks or adjustments on the AirPort Extreme, you can disconnect the Ethernet cable.

I recently upgraded my internet service with Comcast for faster internet. When I user ethernet connection I get 50 MB download speed....when I use the wireless connection I get 10-20 MB speed. I have an airport extreme...3-4 years old. Why?

I recently upgraded my internet service with Comcast for faster internet. When I use an ethernet connection I get 50 MB download speed....when I use the wireless connection I get 10-20 MB speed. I have an airport extreme...3-4 years old. Why is the speed so different and are there settings I can change to increase the wireless speed?

If your supposed to be getting 20 Mb/s down via your ISP and both Mac's are not getting that on the SpeedTest, then obviously your router appears to be the cause.
Connect one Mac directly to the ISP's modem, power off/wait 30 seconds/then power on, then power on the Mac. The ISP will connect directly to the Mac, then run a SpeedTest.
Then repeat the same for the other Mac. If both Mac's have a problem then it's possibly the ISP, the modem, your lines to them or on your property, or both Mac's are messed up.
You'll have to keep searching for the cause. Call your ISP and ask then to run a test to see if your getting your 20 Mb/s to your modem, that should clear part of the problem.
Diagnosing network issues

HT4600 i Get a solid amber light sometimes, bUT all works fine. I have to unplug the airport extreme to reset it and then it turns green and starys that way for a week or so and then turns back to amber. why is this and how do i fix it ?

I gat a solid amber light once a week on my airport extreme, but all works fine. I have to unplug it to reset it and then the light turns back to green and it is good for another week and then it happens again. why is this and what can i do to fix it ?

Solid amber on an AirPort Extreme is an indication that the internal power supply is starting to act up.
If the AirPort Extreme is in warranty, it shouid be exchanged for another AirPort Extreme.
If the AirPort Extreme is several years old, keep any eye on things. When/if you find that you are having to reset the device several times a week, it's time to start thinking about a replacement device, as the end is near.

New Airport Extreme is "slower" then the old one

Hi to all, today I bought the new (faster) Airport Extreme BaseStation. After Installation with the Apple standard settings I have a lower date rate (between 15 to 45 MBps) then I had with the old one (between 52 and almost 100MBps). The position of My MacBookPro and the new Airport Extreme BaseStation is exactly the same then I had with My old one. Why does that happen?

Hi! Yes if you go to Wireless then Options, check the box for a different SSID name for the 5 GHz band. Then make sure your mbp connects to the 5 GHz band and not the 2,4. Though there is some big issues with the new AEBS. Please send feedback to Apple about the speed difference at http://www.apple.com/feedback/airportextreme.html
Hope it works out!

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network?

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network? Network is administered through an iMac running OS X Yosemite 10.10.2. Ideally, would like for the second Airport Extreme hard drive to appear on the list of devices in the Finder window.

Ok.. gottcha
The problem is network wise.. Yosemite is about equal to tin cans and string.. pathetic.
Here is my usual set of instructions to get anything working on Yosemite.
The best way to fix problems is a full factory reset of all the AE in the network.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 and AEwifi for basestation and wireless respectively.
Even better if the issue is more wireless use AE24ghz and AE5ghz with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for AE which is router.. it is a problem for AE which is bridged.. you will need to set static IP in the main router by dhcp reservations or use static IP in the AE which is tricky.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Now mount the disk of the second AE in finder... manually.
Use Go, Connect to Server and type in the AE ip address.
SMB://10.0.1.2
Where you will replace that address with the actual address. The network resource should be discovered and then it will request the password.. type that in and make sure you tick to save it in your keychain.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
Do as much as you want of the above... not all of it is necessary.. only if you want it reliable.. or as reliable as Yosemite in its current incarnation can manage.
The most important thing is point 6.. mount the disk using direct IP address and not names.. dns in Yosemite is fatally flawed.
See http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

Graphite BS faster then Airport Extreme BS - Why?

Similar Messages

Maybe you are looking for