Graphtech cutting master 3 problems.

I have a mac osx 10.8.5, and a graphtech CE6000-60 vinyl cutter.  My problem is I can't get the cutting master 3 plug in to work, I keep getting an error message that the cutting master 3 software is in an unknown format.  If anyone has had any experience with this your suggestions would be greatly appreciated.  Aloha.

Hi Di in CS,
You can install any commercial plug-in designed for use with Illustrator.
To install an Adobe Systems plug-in module, use the installer if one is provided. Otherwise, drag a copy of the module to the Plug-ins folder inside the Illustrator folder. Then restart Illustrator for the plug-in to take effect.
To install a third-party plug-in module, follow the installation instructions that came with the plug-in module.
Hope this helps.
Regards,
Sumit Singh

Similar Messages

  • Illustrator CS5 and Cutting Master 2 (Craft Robo V1.94) plugin

    I have a problem with Illustrator CS5 and a Cutting Master 2 (Craft Robo V1.94) Plugin for a Graphtec Craft Robo Pro vinyl cutter.
    When trying to plot from Illustrator the dialogbox that normally appears does not show and after sometime I get a message Cutting Master 2 timeout.
    Until this appears, Illustrator is Unresponsive.
    I have tried to uninstall the plugin, restart my PC (windows 7 - 64 bit) and reinstall the plugin without success.
    It has been working earlier, the problem recently appeared - any suggestions on how to overcome this very annoying problem?
    Message was edited by:Skilteskoven.  I have now been investigating the problem further, and it seems that an automatic update of windows (I have disabled that feature now!!) - Internet Explorer 11 for windows 7 is causing the problem. I have tried on two different PC, one windows 7, 32 bit and the other windows 7, 64 bit. On both PC the problem as described above occurs when Internet Explorer is installed - anyone who could give me a suggestion on what is going on? How can IE11 cause a plugin in Illustrator to stop working?

    Hi
    Me too.
    You can go back to ios 10.8 providing you have a time machine back up. Thats what I had to do.
    Graphtec are updating drivers and a schedule is here;
    http://www.graphteccorp.com/doc/Topics_Status(Win8&MacOSX10.9).pdf
    Best regards
    Robin

  • How do I install Cutting Master 3 (plug in) into Illustrator CS6?

    How do I get Cutting Master 3 to show up in Illustrator CS6, so I can use my vinyl cutter?

    Hi Di in CS,
    You can install any commercial plug-in designed for use with Illustrator.
    To install an Adobe Systems plug-in module, use the installer if one is provided. Otherwise, drag a copy of the module to the Plug-ins folder inside the Illustrator folder. Then restart Illustrator for the plug-in to take effect.
    To install a third-party plug-in module, follow the installation instructions that came with the plug-in module.
    Hope this helps.
    Regards,
    Sumit Singh

  • How do I install Cutting Master 3 to Illustrator CS6?

    How do I install Cutting Master 3 (plug in) into Illustrator CS6?
    I have tried and it is not working. 

    Hi Di in CS,
    You can install any commercial plug-in designed for use with Illustrator.
    To install an Adobe Systems plug-in module, use the installer if one is provided. Otherwise, drag a copy of the module to the Plug-ins folder inside the Illustrator folder. Then restart Illustrator for the plug-in to take effect.
    To install a third-party plug-in module, follow the installation instructions that came with the plug-in module.
    Hope this helps.
    Regards,
    Sumit Singh

  • Final cut pro problem when exporting with quicktime movie

    Hello!
    I must have som help beacuse my musicmovie must be finsihed untill today. I have a movie their i had used filters like colour correction and interlace. When i export with USING QUICKTIME CONVERSION and have
    keyfram 10
    bitrate 6000
    faster encode
    size 1920x1080 HD 16:9
    its not a problem the movie works fine all the way.
    But when i export with QUICKTIME MOVIE it dosent work. Some clips are frozen and some are beeing misscoloured. None of them have interlace. Its the same clips that dosent work everytime i had export with QM. I have tried to replace these clips but the same thing is happening. I dont understand why i cant use quicktime movie but it works with quicktime conversion.
    If you have an e-mail i can send you just the part where this happening.
    Please help me!
    Thanks Gabriel

    I am also expriencing the same error. Tried every solution listed so far:
    1. Switch off background rendering. Trash render files. Don't render. Export.
    2. copying the project within Final Cut Pro into another project
    3. remove the following folder: Library > Application Support > ProApps > MIO > RADPlugins > XDCAMFormat.RADPlug
    Nothing worked. I try to export to Vimeo, YouTube, and master. All error right at 9%
    What's going on?

  • Final Cut Pro Problems! "PLEASE HELP"

    Hi people, I'm having problems with Final Cut Pro and my Camcorder!!
    Here is the deal:
    My Mac: iMAc, System 10.5.8, 4GB RAM
    Final Cut Pro 5.1.4
    Camcorder: Sony HDR FX7
    Fire Wire Cable
    The problem...
    I have wworking with this many months is good way, last night a power fairlure make restart my mac, and close suddenly FCP..
    When restart the FCP loose all the preferences and presets in the Audio/Video Settings...
    Now I'm like crazy trying to print this work to tape and it doesnt work...
    I can Capture video, I can edit but I dont know what is wrong with PRINT TO VIDEO!
    The settings are in:
    Sequence Preset: HDV - 1080i60
    CapturePreset : HDV
    Device Control Preset: HDV Fire Wire
    Video Playback: Digital Cinema Desktop Preview
    But I remember that in the past in the past in the Audio/Video Settings in the part of: A/V Devices it was in
    Video: Apple Fire Wire NTSC (720 x 480)
    Audio: FireWire DV
    I know that I'm working in HD and printing to video in low res, but is that here in miami the tv Channels I DONT KNOW WHY?? They dont accept tapes in HD!!! Crazy but truth!
    Well guys, I hope you can help me and excuse my english that is very bad but is not my native language and I move here to Miami one year before!
    Thanks a lot for you value help.
    Best Regards,
    Gustavo

    Hi guys,
    Well let me tell you...
    I make the easy setup with 108060i and now is working good and printing to tape, but is so slow...
    I remember that before I use to print to tape in 720x 480 cause is more faster and easy, in fact the tv channels doesnt accept tapes in high def! Is absurd!!
    But I need to know how chance the settings audio/video to 720 x 480 but I already try with every single combination and no one works!
    thanks again!
    Also... I need to know what external hard drive is the best and faster to keep my finalcut archives and after make print to tape!
    I have one seagate 1TB but this have an option that I can avoid that is that the disc go to sleep at the 5 minutes and this screw my print to tape work!
    Did you know some one good with Fire Wire??
    thanks a lot, and have a great day!
    Gustavo

  • [TV@Master] Problem please help

    I have Msi.mother board PT8-Neo -LSR ,  Model No.Ms-6799 , main board bios -Phonenix ,maind board version i updat it to 2.2 , cpu size 2.4 G celleron D/256/533 , memory size 256DDram (400),display card Nvidia Riva TNT2 model 64
    the problem that i face it when i put my TV@nywhere -master card ,the pc stop at the main page that show the biso version and name of bios company and the letters do not bost well it look like a virus work , and when i take tha card off the pc go normally , i tried put it to other PCI the same problem
    please help

    i meany by fix the problem of getting the pc go on to windows with card on PCI salot but i still have the broblem of the driver
    please read my reply again
    my operating system is win me and i have also another pc have XP
    when i log in to windows the system show that found my TV@nywhere card but it didnt took the installatin driver for it i tried to install the driver directly
    but it give me this 2 mesages  when i try to install the driver
    MSI TV card is not found ,stop the installation
    the other message is
    MSI pvs driver installatin failed
    i download the driver from msi page also give me the same messages
    for known on Device Manager it show me that the driver there but do not have the driver and the ? mark beside them
    what to do now 

  • Motion and Final Cut Pro Problem

    I recently updated my computer and went with the new Quad-Core Mac. I had to reload the Final Cut Pro Studio software, and I've got a problem that is vexing me to no end.
    I can import a Motion template (one that I've designed and even the Apple produced templates), but I try to view it in Viewer or when I place the Motion template on the timeline it won't work. Nothing visible on either the Viewer or the Canvas when I try to playback. I can right click and open the template in Motion and have the elements appear and work properly, but nada once it comes back into Final Cut.
    What gives?
    John

    I find the roundtrip to Motion to be less than useful when there are a lot of layers involved. What works better for me is to export a movie using the same settings you're using in FCP and then import that. If the settings in Motion match the FCP settings, no rendering should be required. Unfortunately, you can't then use the "open in editor" function to fix anything... but must reopen the Motion project and export again.

  • Lsmw customer master problem

    hi gurus,
    i have tried lsmw with customer master using program RFBIDE00.
    i went upto step convert read data.
    my problem is
    when i read data it shows all fields correctly filled. but after converting data it is not showing
    the correct fields and mapping data correctly.
    and more over in converted data it won't show structure name in left side coloumn.
    thanks and  regards,
    dharani kumar

    Hi Dharani,
    First check ur Maintain source fields (the way(order) ur defined here , in the same way u have to take in the flate file(its not mandatory to take in the same way(y iam telling means mostly we get confusion(if we are not aware of lsmw) ),
    and also check the length and character type (all fields should be Character type c) and length is not less than Data dictionary length).
    and after that  check ur mapping step , have u done proper mapping r not .
    if everything is done perfectly , and also issue is not resolved , just have a ping.
    Reward points if helpful.
    Thanks

  • AS01 Asset Master - Problem with Cost Center in Time Intervals

    Hello experts,
    I need your help to solve this problem, in the tab Time-dependent - More Intervals - Overview of time intervals
    When i add a new interval and change the Cost Center, the system modify all the previos intervals setting the last Costo Center to all, i dont know why the system do that, thanks.

    Hi Gaetano,
    check that the prerequisites which are explained in [Note 684659|https://service.sap.com/sap/support/notes/684659] are fulfilled.
    I assume that you are on a release R/3 Enterprise or higher.
    - KOSTL activated in ACSET
    - cost element existing
    - field status allows KOSTL in the account
    - cost center maintained in asset master record
    Regards,
    Markus

  • Apple Mail Cut & Paste Problem...

    I have a problem with Apple Mail when I cut some text and paste it somewhere else within the message it doesn't go in where the cursor is located! Instead it pastes into what appears to be a random place elsewhere in the message usually at the start of the line or paragraph.
    It's really strange and completely unfathomable. The only solution I've found is to put in a couple of returns paste it in to the message then move the cursor up and delete the newly added line breaks.
    I thought it might be a font issue so I changed my default font from Arial to Trebuchet and it's still doing it. This doesn't appear to happen in any other application.
    This is not exclusive to Snow Leopard as it does it on my Mac at home which is running Lion.
    Any advice gratefully received.
    David

    David -
    I have also been experiencing this oddball aim issue when attempting to insert clipboard contents into a specific point in Mail. I am writing to lend credence to the contention that this is an Apple Mail issue that really should be fixed. Apple started the cut & paste revolution and the fact that one of their key software packages cannot paste properly strikes me as a bit ludicrous.
    This started happening on both my iMac and MacBook Pro a few months ago. It could be that it correlates with my use of three different styled signature files for three different e-mail accounts (I hadn't thought of the connection, so thank you, I had been wondering if they had altered something in one of their many security updates).
    I desired that the body text of my e-mail  default to something different from the style of my signature files. Mail is fairly limited in this area, so I include a top line my signature file that has the right style for my body text. Now I start all messages by overwriting that styled text, so my message font is as I want it. Is this the source of the problem?
    The inability to place text correctly isn't restricted to pasting something in via clicking on a particular spot in the e-mail. Odd things also happen if you use the directional arrow keys to move the cursor around with the keyboard and then command-V, or if you drag text to a certain spot, and when you release, it refuses to go there.
    There's some logic to the mistakes. The text is almost always placed a couple of lines above where the insertion point is blinking, and you can fool Mail sometimes by placing text in the middle of a bunch of new returns and then deleting the surrounding lines, but this is cumbersome and annoying.
    I hope Apple reads this, because it got so annoying that I switched to Outlook (Office 11) and it's terrific in some of the areas where Mail falters (work e-mail is Exchange). About the only thing that Mail does better is access my MobileMe folders much more quickly.
    Come on, Apple!

  • Illustrator CS6 and Cut Studio problems

    When I cut with Cut Studio from Illustrator CS6, my stuff may or may not cut completely.  A lot of the time it stops midstream then i have to restart it cut again.  Very time consuming and not profitable either.  Anyone else with this problem and can it be fixed?

    I have a Imac g5 only couple years old now, but had the issue right off the bat.  Mac OSX Lion 10.7.5    Roland Camm-1 Pro  GX 500     Cut studio
    As far as artwork goes, it is random when it runs.  old existing files, brand new files, might be a graphic or verbage.  Doesn't seem to care.  The only thing i have noticed is most of the files i get from a customer (which isn't often) runs without a hitch.
    I feel CS6 is not up to snuff as a program.  CS2   and AI 8  were awesome but won't run on my new machine.  would you suggest i try to install Cut Studio again, check on the driver?
    thanks

  • TV@nywhere Master problems

    I recently purchased TV@nywhere Master to use on my Dell Dimension 4550 which runs WinXP, and would like help with the following issues:
    •   The signal for the TV card is provided by an antenna however, it is not strong enough to reach the tuner’s threshold, so none of my channels show as available in SETUP. I have already downloaded and installed the three latest driver versions from the MSI website. Do you have any suggestions as to how I can remedy this situation? The same antenna provides the signal to our two TVs, and our reception is perfect.
    •   I have twice attempted to register this card on your website, and have been told both times that my sessions, which took about a minute, had timed out! Can you fix this, please?
    •   The radio comes on unbidden whenever I start my computer, and after it comes out of standby mode.

    I have a TV@nywhere master and I live in the UK.
    I do not have any problems with tuning the stations with MSIPVS. All 4 main channels work fine, it also tuned in to some weaker signals. The only terrestrial channel I can not get is channel 5 but that is because they is no channel 5 by aerial in my area.
    You could try fine tuning the channel that BBC2 is on, it may help, how to do it is in the manual.
    The drivers on MSI web site are not for the master (MS-8606) version they are for the original TV@nywhere and the TV@nywhere Master drivers are the same version number as the one on the website but have probably been tweaked to accommodate the new Microtune MT2050 tuner.
    The only gripe I have about the MS-8606 is the drivers for the tuner. They do work BUT if you want to use any other software that works with the new CX2883 and MT2050 chips, you have to run MSIPVS first to get the tuner to work. The display within MSIPVS also leaves a lot to be desired especially after using Dscaler (no tuner - video-in only). Video-in is not a problem and works with most well know freeware/shareware software. The capture quality (which is my main concern) is excellent when using the higher setting. I have captured some footage of an holiday video that was transfered to an very high quality VHS tape nearly 12 years ago, and converted it to an SVCD. The quality of the end results is as good as the original VHS tape. I have also capture from the Tuner in DVD quality and it is almost undistinguishable from a real DVD`s play back and certainly better than some cheapo DVDs.
    As the Tuner and encode/decoding chips are very new (product only released 3-4 weeks ago) support and new drivers will take time to appear, BUT even without the support etc. I can still see the quality that this card as to offer.

  • Customer master problem

    Sir in tcode VA01 i am getting error message no. VP199.[no customer master record exists for sold to party  1 ]What to do ?
    I am online.

    Hi raghav
    Check in t.codes VOR1 and VOR2.If the data is not mainatained maintain there.It will solve your problem
    Regards
    Srinath

  • CSS virtual-router master/master problem

    Dear all experts,
    I have two CSSs 11150 and have configured them as following:
    CSS-1#
    circuit VLAN100
      ip address 172.10.10.101 255.255.255.0
        ip virtual-router 1 priority 105 preempt
        ip redundant-vip 1 172.10.10.1
        ip critical-service 1 up_down_stream
        no redirects
    CSS-2#
    circuit VLAN100
      ip address 172.10.10.102 255.255.255.0
        ip virtual-router 1 priority 101 preempt
        ip redundant-vip 1 172.10.10.1
        ip critical-service 1 up_down_stream
        no redirects
    Here is my connection:
    CSS-1 <=> Switch <=> CSS-2
    They were working fine before but CSS-2 suddenly change to master few days ago. I have already checked the connection between these two CSSs and it seems ok, so I tried to capture the packet trace both for the ports connected to CSS-1 and CSS-2 from the switch. And finally I found that I can see the vrrp adv. message which send from CSS-2 at the port which is monitoring CSS-1, but there is no vrrp adv. message send from CSS-1. I am not sure the problem is related to the acl as it has configured to permit any any:
    clause 254 permit any any destination any
    Could anyone can help me in this case? Is the problem related to the keyword "preempt" in CSS-2? Is it a software bugs which hasn't listed in cisco bug list (SW Version: 6.10)?
    Thanks!

    Hi,
    I'm not sure if this you've resolved this problem; however, from what I have read you should never configure the preempt option on the same virtual router on both CSSs.
    The issue of both CSSs becoming master when using the preempt option is highlighted in this guide:
    http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/css11000series/v5.00/command/reference/CmdCirIP.html#wp1027189
    I have used the preempt option to failover to the backup CSS in the past; however, to achieve this the preempt option had to be removed from the existing master.
    I hope this helps.
    Thanks,
    C

Maybe you are looking for