GRC AC 10.1: Authorizaion Sync Job Error
Hello Everyone,
I'm currently configuring my GRC 10.1 Access Control, I have just finished my common configuration tasks and ran the initial Authorization full sync job.
and am facing the below error message.
Authorization Sync
Starting authorization sync for connector SE3CLNT302 and language EN
Error in SE3CLNT302; Reason Error in RFC; 'No RFC authorization for function m
PFCG authorization sync failed with errors
Repository Object Sync
Program for Repository Profile Syncronization
Processing for connector SE3CLNT302
Error in RFC; 'No RFC authorization for function module /GRCPI/GR'
Profile sync failed with errors
Program for Repository Role Synchronization
Processing for connector SE3CLNT302
Error in RFC; 'No RFC authorization for function module /GRCPI/GR'
Role sync failed with errors
Program for Repository User Synchronization
Processing for connector SE3CLNT302
Error in RFC; 'No RFC authorization for function module /GRCPI/GR'
User sync failed with errors
Repository Object sync job failed with errors
Please check SLG1 for further details
I have double checked my connector settings and connection setting, everything seems fine. I checked the tables GRACCONNSTAT and GRFNCONNSCNLK, the tables are populated correctly. I checked to see the RFC ID passes the authorization test and connection test and the logical systems are populated in BD54, can anyone please tell what I'm missing here and why i'm facing this error message?
Hello Reddy
Kindly assign the role SAP_GRAC_ALL to the RFC user . This user can also be
assigned the profile SAP_ALL.
Best Regards,
Neeraj
Similar Messages
-
Hi Experts,
I am getting error while running sync job. I searched but couldn't find a solution.
We have two GRC AC10 clients setup, one is for fresh AC10 installation testing and another is for migration testing.
Both clients talk to two different ECC clients. Issue is that we have setup all SPRO configurations, plug-in settings and stuff which is described in AC10 post -installation and migration documents,
Sync job for one client is successful, but sync job for another client is giving error -
Error message -
Starting authorization sync for connector IE9_600 and language EN
Error in IE9_600; Reason Error in RFC; 'Function module "/GRCPI/GRIA_AUTH_G
PFCG authorization sync failed with errors
I have checked plugin settings, RFC and other settings, it seems ok as it is in another client.
What could be the cause and solution? Any suggestions are highly appreciated.
Thanks in advance,
Regards,
SabitaThe issue resolved, RFC was incorrectly pointed to wrong client.
Regards,
Sabita -
RFC error while running sync job in AC 10
I have done all the configuration to add new SAP system via SPRO in GRC 10. Now I am trying to run the sync job for the first time, I am getting the below mssage. I checked the RFC desitinations, it looks fine.
Error in RFC; 'Function module "/GRCPI/GRIA_ROLE_GET_RANGES" not'
Error in RFC; 'Function module "/GRCPI/GRIA_ROLE_GET_RANGES" not'
Role sync failed with errors
Program for Repository User Synchronization
Error in RFC; 'Function module "/GRCPI/GRIA_USR_GET_RANGES" not f'
User sync failed with errors
Repository Object sync job failed with errors
Please check SLG1 for further details
I checked in SLG1 also, its displaying the same errors as listed above. I have some systems added earlier which are correctly configured and working fine. I tried to match the configuration with the new systems, and everything looks fine. Not sure why this error is coming.
Please someone can help.Hello,
It seems to be a problem with the add-on in the back-en system, and a function module couldn't be found. Check the RFC connection (refer here for example GRC AC10 sync job error ) and make sure the add-on is properly installed.A simple check could be go to the back-end system, tx SE37 and check if the function modules exist.
Cheers,
Diego. -
Errors while running Sync Jobs in GRC 10
Dear Experts,
I am trying to configure RAR in GRC 10. I have all required config steps and now I am trying to run Sync Jobs and I am getting below errors.
Authorization Synch
Program for Authorization data Synchronization
Starting authorization sync for connector RC1 and language EN
Error in RC1; Reason Error in RFC; 'Function module "/GRCPI/GRIA_AUTH_G
PFCG authorization sync failed with errors
Repository Object Synch
Program for Repository Profile Syncronization
Processing for connector RC1
Error in RFC; 'Function module "/GRCPI/GRIA_PROF_GET_RANGES" not'
Profile sync failed with errors
Program for Repository Role Synchronization
Processing for connector RC1
Error in RFC; 'Function module "/GRCPI/GRIA_ROLE_GET_RANGES" not'
Role sync failed with errors
Program for Repository User Synchronization
Processing for connector RC1
Error in RFC; 'Function module "/GRCPI/GRIA_USR_GET_RANGES" not f'
User sync failed with errors
Repository Object sync job failed with errors
Please check SLG1 for further details
I appreciate your help.
Thanks,
RajHi Raj,
I have a similar error for which I have put up a separate post, your input would be highly valuable.
My RFC connection works via the test in SM59 but when executing GRAC_AUTH_SYNC I get a simiar error to your above.
Please let me know what steps you took.
Best regards,
Paul -
Issue with Authorization sync job in GRC 10.1
Hi,
I am facing below issue while running the authorization sync job in 10.1 after importing the configuration data as part of migration from 5.3 to 10.1.
we have GRC server and plugin system on the same SP level 04.
Error:
Error in GRCAC101EC; Reason Error in RFC; 'Function module "/GRCPI/GRIA_AUTH_G
PFCG authorization sync failed with errors
Thr RFC connection is working fine and the connector settings are done in GRC. Also the RFC user has SAP_ALL.
Regards,
Giridharthe sp seems a little low
have a look at Error in RFC; 'Function module "/GRCPI/GRIA_PROF_GET_RANGES" not' -
RAR 5.2: Background Job Error
During the Full sync jobs after installation of RAR 5.2, the User and Role jobs complete successfully, but during the profiles job it stops with an error.
Please find the log entries and any tips are highly appreciated.
Thanks:
INFO: Job ID:7 : 7 out of 5290 (0%) done
19-Aug-2008 20:15:14 com.virsa.cc.xsys.bg.BgJob setStatus
INFO: Job ID: 7 Status: Running
19-Aug-2008 20:15:14 com.virsa.cc.xsys.riskanalysis.AnalysisEngine
performActPermAnalysis
INFO: Job ID:7 : Before GC => memory usage: free=391M, total=981M
19-Aug-2008 20:15:14 com.virsa.cc.xsys.riskanalysis.AnalysisEngine
performActPermAnalysis
INFO: Job ID:7 : Analysis starts: &_SAP_ALL_7
19-Aug-2008 20:15:14 com.virsa.cc.xsys.meng.MatchingEngine getObjActionsINFO: -
allAreExclude=>true----
19-Aug-2008 20:15:14 com.virsa.cc.xsys.meng.ObjAuthMatcher <init>
FINEST: ObjAuthMatcher constructed: 0ms, #singles=1, #ranges=0, #super=119-Aug-2008 20:15:15 com.virsa.cc.xsys.riskanalysis.AnalysisEngine
insertAllTcodeACTVL
WARNING: Job ID:7 : Exception: Missing IN or OUT parameter at index::
13, SQL State: null
java.sql.SQLException: Missing IN or OUT parameter at index:: 13
at
oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:112)This could be due to data issue or wrong RTA SP level. Please check with GRC support.
Thanks
Prem -
Org. value sync job in ERM
Hello experts,
Scenario: Our backend system consist HR component, but we do not use it and therefore do not want to implement the HR RTA
So my question is, Is it possible to skip the HR contents for the org. value sync job in ERM? As we encounter error when running the report, and if possible, we would like to skip the HR contents which is not neccessary for our environment.
Appreciate any feedback for this, thank you in advance.
regards,
weihowHello Wei,
If your system has SAP_HR component installed then you must install the VIRSAHR component for GRC as well. Reason being that there are some function modules which are there specifically for system with SAP HR component installed. If SAP HR is there then GRC applications will use the functions available in VIRSAHR component for activities. If you do not install them then this can lead to problems. You can refer to SAP Note 1086823 which confirms this.
Regarding the ORG value sync job, you can customize it to not to pick any specific type of data. It will pick all the ORG value related data in your system.
Regards,
Varun -
GRC 10.1 SP06 - Role sync fails with dump DBIF_RSQL_INVALID_RSQL
Hi!
We're experiencing an issue with the repository sync job for one connector. When selecting the full option, the sync for users and profiles report success but for the role sync we get the error "Error in RFC; 'Error in module RSQL of the database interface'" and a dump is generated in the back-end ( DBIF_RSQL_INVALID_RSQL) with the program /GRCPI/CL_GRIA_ROLE===========CP
The problem occurs in the sentence:
>>>>>
SELECT agr_name parent_agr FROM agr_define
"#EC CI_SGLSELECT
84
INTO TABLE lt_derived
85 *
WHERE agr_name IN it_incl_role
86
WHERE agr_name IN lt_incl_role
87
AND ( change_dat GE iv_update_date OR
88
( create_dat GE iv_update_date AND change_dat = '00000000' ) ).
We've tried working with the parameter 1122 (Batch size for Role sync) switching it to different values like 500, 100, 50, 10 and even 1 but the error still persists.
Synch for another connector with the same GRC System works fine.
any idea?
Thanks,
Diego.Sounds like an old foe from 10.0
http://service.sap.com/sap/support/notes/1632421
You may have to ask SAP to make a 10.1 version of this fix for you to apply to the plug-in system.
There is a specific note for this issue in both 10.0 and 10.1, but it is part of 10.1 SP01 (you are on SP06)
http://service.sap.com/sap/support/notes/1803121 -
If 2 vendors have same address in ECC, will both the vendors get tranferred from ECC to SRM using vendor sync job -BBP_VENDOR_SYNC. I know in BBPGETVD there is an option to deselect address comparison to avoid duplicates - not sure though about vendor sync program - BBP_VENDOR_SYNC. Can anyone confirm based on their experience . Thanks - SK
What I know is this, that you should definitely use BBPGETVD for new vendor transfers and it does compare the addresss of the vendors on the selection screen if the box is not checked. You will get a replication error in this case as I recall (SLG1). And I have had dialogue with SAP regarding changing the address of a vendor and it not being picked up by BBP_VENDOR_SYNC. Apparently according to them, in this case no checking of addresses occurs since the possibilities in terms of total address volume could be horrendous in terms of performance.
Cheers... -
Hello SAP gurus,
we're performing the initial configuration of the SOLMAN 7.1 for Enterprise Linux 5 and Oracle 11G.
After setting up the LMDB, the synch batch (SAP_LMDB_LDB_0000000001) executed every 10 minutes fails, and the message prompted in the log does not seem very helpful, neither have I find anything in the web:
Sync job failed with error: Source and target model vers. are lower than the r ***
Any idea? Could it be the server object name? I haven't requested any in http://service.sap.com/namespaces but use one I defined. Is that really necessary? My user does not have permits to launch that request.
Thanks. Raúl.Hello,
Which SLD are you using to sync to LMDB.
Check the SLD version and SLD content version.
Follow the document:
Landscape Management Database (LMDB) - Setup Guide
Check this guide at:
https://websmp102.sap-ag.de/support
In Knowledge Exchange-> Ramp up knowledge transfer.
Go to SAP Solution Manager 7.1-> Setup and Operation
This should help.
Regards,
Sunny -
Software Update Deployment - Job error (0x80072f0c) received for assignment
I'm deploying a software update to my test clients but half of them failed with error below;
UpdateStore.log -
Failed to refresh sync message. Error = 0x87d00310.
WUAHandler.log
OnSearchComplete - Failed to end search job. Error = 0x80072f0c.
Scan failed with error = 0x80072f0c.
Updates Deployment
Job error (0x80072f0c) received for assignment ({0F2CA22F-BB7A-4ED8-9794-15AB24B83E09}) action
Do you have any recommendation ?Since no one has replied to this post, I recommend that you contact Microsoft Support (CSS) directly, they can work with you to solve this problem.
Garth Jones | My blogs: Enhansoft and
Old Blog site | Twitter:
@GarthMJ -
Since reinstalling itunes i can no longer sync. Error message says already synced with another itunes library. I get a blank sync - no songs, photos ect as it comes up with this error whenever try to select what is to be synced. Help - lost everything. Complete nightmare - Apple sort a fix NOW, but will take any help
Plawexki wrote:
... do you know if the contacts, photos, messages etc will be wiped?
Yes... Everything will be Wiped and Replaced with what is currently on Your Mac.
SYNCING with iTunes
See here > http://support.apple.com/kb/HT1386
From Here > http://www.apple.com/support/iphone/syncing/
You may find this information of interest...
Have a read here...
https://discussions.apple.com/message/18409815?ac_cid=ha
And See Here...
How to Use Multiple iDevices with One Computer -
Sending job error message to admin by email
Hi everyone...
Anyone knows how to send job error message to admin by email? For example, if crawler failed, an email is sent to admin with the error message. I'm thinking of building windows service which run at the background and knows when a job fail and send the error message through email to admin.
Is there a better way?
Cheers,
Jefi Santosohi,
>>>Can this be achieved through BPM?
yes you can put your transformation step
and send step in a block and specify an exception
branch and catch all exceptions that will
occur during transformations and the send step
then you can send info from the exception branch to
any other system
you won't be able to catch the error's name
but you will be able to notify any thinrd party
about the error
more on error catching:
http://help.sap.com/saphelp_nw04/helpdata/en/33/4a773f12f14a18e10000000a114084/content.htm
Regards,
michal -
Hyper Transport Sync Flood Error (msi 785gm-e51)
hello all,
my pc
x4-630
his 5750
vgen 2gb 1333
corsair 450w
i have problem with my pc. sometimes its reboot when im playing games.after reboot there a error messege hyper transport sync flood error.
i already google about this problem and i got a information on the google this problem caused by my motherboard.
how to solve this?Quote from: Svet on 16-July-10, 17:45:09
error in memtest or "Hyper Transport Sync Flood Error" ?
Use normal English, not "r", "u" and such.
What exactly? brand model?
Have you tried with different one?
In which dimm slot is installed?
done >>Clear CMOS Guide<< with power cord removed,
and 'Load bios optimized defaults" ?
error in hyper transport sync flood error
brand name vgen,
here the full spec i got from vgen website :
DDR3 PC 10600/1333Mhz
Category
PC Memory
Type
Long-DIMM DDR3
Size
130 x 30 x 2 mm
Status
New
Description
capacity : 2GB
speed : 1333 MHz
CAL : CL 9
Chip Configuration: 32M x 8 8 Chip
Chipset : Major Brand
Jenis IC :Tiny BGA
Slot : DIMM 240 pin
Tipe : Unbuffered
Voltage : 1.5 V
ECC : No
Registered : No
i never tried with other ram
honestly i dont know what is dimm slot, but if i dont get you wrong its number one slot ram.
yes i already test clear cmos with power cord removed because i afraid get electric shock (im not pc expert)
oh ya found quote in another forum
After reading about 200 threads on this problem, I came to the conclusion that it's a voltage problem. It's not BIOS, an ATI series of video card, faulty CPU or RAM, or a motherboard. The frequency of AMD CPUs being mentioned, power needs, and the ability of BIOS to compensate for voltage changes led me to believe that this is a problem with under-voltage. I don't have the time to experiment with each and every variable, so I upped the voltages in BIOS on all elements of both RAM and the CPU. Before this, I was getting a reboot at random and increasingly irritating times (I do annoying grad homework on this thing). So, after upping the voltages, I haven't had one reboot for HTSFE. If anyone wants to go from here and mess with the individual voltages, go for it. It's definitely a voltage problem. Hope this helps.
so i test it, i upped all voltages that i can change in BIOS. so far its already 2 day without Hyper transport error.
it is fine to upped all voltages?i up it until the highest "white" voltage ( i read in BIOS, grey=auto, white=normal, red=no recommended) -
I updated to iTunes 12 and didn't like it. Followed advice to revert to 11.1. Now my iPhone 5 won't sync and error message says I need iTunes 11.2 or higher. Apple Download choices didn't have anything between 11.1.5 and 12. What can I do? Using iTunes 12 is not an option. Many features I used for audiobooks have disappeared.
The version immediately prior to 12 was 11.4.0.18. Here are direct download links from Apple's servers:
iTunes 11.4.0.18 for Windows (32-bit) - iTunesSetup.exe (2014-09-09)
iTunes 11.4.0.18 for Windows (64-bit) - iTunes64Setup.exe (2014-09-09)
tt2
Maybe you are looking for
-
Hi all, I was trying to execute the following code: import java.io.BufferedReader; import java.io.InputStream; import java.io.InputStreamReader; import java.sql.CallableStatement; import java.sql.Connection; import java.sql.DriverManager; import java
-
Message failed in SMQ1: XIAFUSER Password no longer valid
hello i am having scenario where a sender file adapter picks the file and pushes to the BPM. but when i checked in SXMB_MONI-> PE, i could see message status "Scheduled on the outbound side" When checked in SMQ1 it gave me SYSFAIL error in the queue.
-
Function Modules, for listing Cost centers Under a manager
Hi All, 1. Can any one please suggest me any Function Module available for listing the cost center under a manager, given only the Manager's username or pernr. 2. And also the Function Group which has the collection of Function Modules which deals wi
-
Hi guys, Need help for routine code, i have rquirement currency translation based on currency type In the cube we having the Amount Key Figure in USD. i want to convert these values based on currency type or company code . ..GBP,JPY,INR,KRW..etc. ca
-
How I can movie the DSC Security defined in one machine to another ?
I have a LV 8.01 and DSP in a development machine. When I move all vi involved to another computer ( with LV PDS ) all security definitions was lost. I'm using a DSC Security. Waht I can do to move the security definician ( domain and users name ) fr