Green shaded monitor with an R9 280x

I am ising a 3gb R9 280x with two monitors i was playing a game and had youtube on on another monitor. suddenly one screen went green but i could still see the features. Then on the other monitor pixelated random lines started to come up. i immediatley restarted to pc thinking it was just caused by the software. then after the same thing the other monitor went green like the other. I have tried reinstalling the drivers, returning it to stock speeds and underclocking the card, making sure the cables are ok and using different cables and trying the monitors with a different pc. I am convinced that it is a gpu problem because there is no on board motherboard graphics. Note that the pc is working perfectly and performing normally but there is always a green cast on the monitor.
PS. i have already tried calibrating the monitors colours and its not that. should i try and send it in for repair on the warranty or does anyone have any suggestions

I have two cards, want to use them in crossfire but didn't install them both because I first wanted to get 1 running before inserting the second one. I tested them both and both have the boot problem. The cards are brand new and I read a lot of cases where people RMA the card to experience the same problem with a new one. I have two, how unlucky can I be if I have two broken cards... I don't have a second PC to test them, so no I didn't try them in an other PC. But I would first like to try everything possible before RMA'ing the cards. And also because Sapphire states the problem on their website.

Similar Messages

Green pixels on external monitor with MBA coming up from sleep?

Has anyone else experienced green pixels on external monitor with MBA coming up from sleep? I can get rid of these pixels either restarting MBA or switch off the monitor for a five secs and then switch it back on. These pixels do not show up within screenshots.. or neither on MBA own screen but they do reappear on external monitor (used with mini DP-DVI-adapter) after every sleep cycle.
http://ssh.nbl.fi/~nbl4264/gp/ (few pics where these green pixels appear on)

I have the same issue with my new macbook.
When i wake the computer from a partial sleep the screen flickers and i get line distortion through the image.
If i put the machine to sleep unplug the mini dvi adapter and replug it in and wake the computer up the problem disappears.
The issue is also intermittent doing about 3 times out of every 10 wake ups...
If anyone has any suggestions it would be great, I a using a new Dell 2208WFP monitor.

Anyone using a Yamakasi Catleap 2703 Monitor with a Retina Mac Book Pro?

Hi,
Anyone using a Yamakasi Catleap 2703 Monitor with a Retina Mac Book Pro? If so, is it working well and would you do it again? Is it compatible with the Apple dual DVI cable?
Thanks,
Alan

I just got a Yamakasi precision 2703. I'm using it with a 13" macbook pro (non retina). I got it working with a thunderbolt / minidisplayport to dual link DVI adapter from monoprice for $~70. At first I didn't think it was going to work, plugged it in, turned on the display, nothing happened. I unplugged, plugged the USB cable back in and the monitor came to life. Working great so far. I bought mine from green-sum on ebay. The recommend not using this monitor with apple computers due to overheating issues... I don't see why that would be the case, though. I've only been running it for a couple days, but so far no issues, and I've been happy with the monitor, no dead pixels, no bleed in the corners.
The monitor stand on the 2703 isn't too bad, a little wobbly but not as bad as the others from what I've read. The monitor does sit a little low, though. I have a much sturdier stand coming from monoprice for $20+shipping, which will provide tons of adjustment, both height and rotation.
Good luck!

Missed event monitor with event reset

I have pretty simple request for Scom monitoring, but I don’t know how to do it. My application generates an event in custom log with name Mpis. Event level is Informational, Event ID is 10 and source is Mpis. This event is created every
5 minutes. If application failed, event isn’t created. I have a need to create an alert, if event isn’t created more than one hour and monitor must go into unhealthy state (red). If same event come back, monitor must resolve itself and go back to healthy (green).
I try doing this with missed event monitor with event reset, but they don’t work as I expected, probably because I use the same event for trigger an alert and resolve an alert. Any idea ?

There must be something misconfigured. Missed Event Detection -> Windows Event Reset is the correct one.
Use Event ID 10 and Source Mpis as expression in both Simple Event Expression and Missing Event Expression. in Missing Event Detection, use "Based on fixed simple recurring Schedule" and choose 60 minutes/1 hour.
I have configured this in my environment, and this works perfectly; if no events are logged within an hour, i get an alert. If i then create the event, the alert Closes.
www.coretech.dk - blog.coretech.dk

RFC monitor with CCMS

Hello,
I'm implementing RFC monitor with CCMS and I have a problem.
I was able to implement the method with an auto-reaction method of send mail.
It is working fine but it doesn't repeat the alert! Let's say, imagine that the RFC isn't working since 3am... we are now at 13pm and the alert is not triggered anymore. In fact, in RZ20 I just see 1 Alert triggered at 3am.
Is there any way to set this alert to trigger every period of time?
thanks.
regards,
Filipe Vasconcelos

Hello,
first it would be good to clarify which monitor are you implementing - there are multiple RFC monitors - for example:
Availability and Performance Overview Monitor :
http://help.sap.com/saphelp_nw70/Helpdata/en/ae/cd823bd26a5c42e10000000a114084/frameset.htm
Transactional RFC and Queued RFC Monitor
http://help.sap.com/saphelp_nw70/Helpdata/en/8b/ceea3b31aac554e10000000a114084/frameset.htm
Best to type the name of monitor as displayed in RZ20.
Based on the type of monitor you might find the answer here:
http://help.sap.com/saphelp_nw70/Helpdata/en/f6/c55c3bab977239e10000000a114084/frameset.htm
(for example for status monitor you can set option "When should a message trigger an alert?" to "Always (at every message)")
Anyway I am afraid that in case you are using performance monitor there is not much you can do. Possibility can be to check if data collection method (for example function) has parameter that can do this (but I am skeptical about this) - if not then you would have to adjust data collection method or implement the monitoring in another way.
Possibility can be to use some kind of "switch". You can activate option "Display All-Clears in Alert Browser" - this will generate green alerts. Then you can program your own autoreaction method that will perform the "switch operation" (simple insert/update/delete into some Z-table you will create - based on status of alert - red/yellow/green.) Then you can have batch job running another Z-program that is reading this value and constantly reminding use via email.
If you program this in a good way (abstract autoreaction method) - you can reuse this solution for other monitors as well and easily buid you own email notification functionality.
I hope it helps.
Best regards.

Colors displaying as dull yellowy-green; new monitor and calibration

Just got a new ASUS LCD monitor, and calibrated it with the Spyder 3 Express.
Now when I import a .CR2 file using Lightroom 3 to edit the RAW image, the color is displayed as yellowy-gray and dull. It looks the same when I pull it into Elements 7, unless I remove all color management (which, if I save the image, actually then renders the image colors neon and oversaturated with lots of pink and red tones). If I export the image from Lightroom 3 the image colors are correct and very different from how they look in Lightroom.
I also use the ACR editor with Elements 7 and I am having the same problem there. Upon opening an edited Jpeg or a .CR2 RAW file there, the color is displayed as dull, grayish yellowy-green.
If I view the very same image in GIMP, Picasa or on the web, as long as the colorspace is intact (sRGB), the color is accurate. Not so in Elements or Lightroom.
If you have experience with this problem is it the monitor, the calibration, or Elements and Lightroom? I am beyond frustrated and need to see my colors properly. I have not had this problem before.
Thanks for your time.

I suggest re-reading C S S Simon's and my reply, including the links I provided with solutions and historical explanation – It is apparent you didn't!
Pay your money and make your display choice, but don't blame the wide gamut capable display because you are unwilling to learn how to use the technology advantages it provides!
Please read this factoid:
All Wide Gamut Displays when properly setup to display in a "wide gamut" mode such as Adobe RGB will only display images correctly in color managed applications – PERIOD.
Your Asus display has two factory calibrated modes, Adobe RGB and sRGB, which will only work properly using the color profile provide to you on CD (or downloaded) by Asus – This the monitor profile Asus used when hardware calibrating your specific serial number monitor at the factory. The displays internal LUT contains that calibration information, and there is no way for you to recalibrate it using a Spyder 3 or other hardware calibrator. I am going to paste here three separate solution alternatives I made at the other post – Use only one (1):
Solution 1) Delete your i1 Display custom profile and install the Asus provided PA246Q driver and profile. Then use the monitor's "factory calibrated" Adobe RGB wide Gamut selector mode with Lightroom and other color-managed applications. When using non-color managed applications, switch your monitor’s mode selector to sRGB. Calibration using i1 Display or other hardware device cannot be used with this option. User hardware calibration should only be performed using the monitor's 'User Mode.'
Solution 2) In addition to your Asus PA246Q wide gamut monitor, install a second standard gamut sRGB monitor. Calibrate both monitors separately using your i1 Display unit, which will create separate profiles for each monitor. Use your Asus PA246Q wide gamut monitor only with Lightroom and other color managed applications. Use your second sRGB monitor for with both non-color or color managed applications. You may still have issues properly calibrating your Asus PA246Q monitor with its proper 'User Mode' selection as others have reported, but the results should be better than what you have now.
http://forums.dpreview.com/forums/readflat.asp?forum=1004&message=3897 4810&changemode=1
http://forums.dpreview.com/forums/readflat.asp?forum=1004&message=3908 1965&changemode=1
Solution 3) If none of the above works for you, get rid of the Asus PA246Q and buy a good standard "non-wide gamut sRGB display.

How do i run an external monitor with my macbook and change settings so that when i close the lid the signal to the monitor is not lost and i can continue using the mac with a mouse and a wireless keyboard?

How do i run an external monitor with my macbook and change settings so that when i close the lid the signal to the monitor is not lost and i can continue using the mac with a mouse and a wireless keyboard?

No, nothing will prevent the computer from going to sleep when you close its display except third-party hacks that are designed to do exactly that. I strongly advise against using any of those, as they may interfere with successful entry into clamshell mode (and they carry other downside risks as well). Just wait until the computer is asleep (with its sleep light pulsing), then press any key on the keyboard. It sounds as though your setup is working as it's designed to do.

How do I use two external monitors with my laptop?

I have a new Pavilion dm4-301 d cl Entertainment PC. My OS is Windows 7. I am used to using two external monitors with a docking station. This new laptop does not have a docking station. What do I need to get to use two external monitors?
This question was solved.
View Solution.

Certainly not without a dock but even with, HP laptop docks pretty well limit you to one of the external monitor ports, even if there are two on the dock. We have used a device called an Atlona AT-HDPIX2 which is a usb to hdmi adapter. It provides a third monitor capability for a laptop....use the native external monitor port and the internal laptop display and then this device gives a third monitor which is full configurable from the Windows 7 display interface...clone, extend, etc. It allows full HD resolution and is responsive enough for even light gaming. HP makes no true docking station for your laptop.

Using ADC Monitor with the new Mac Mini

My husband has an Apple monitor with an ADC connection. I would like to purchase the new Mac Mini, but would like to use his current monitor. I know there is an ADC to DVI adapter, but the new Mac Mini uses the Mini Display...could I use yet another adapter? I am trying to save money, but don't want to the display quality to be really poor. Space is not an issue. Any help would be greatly appreciated.

I have located that, but my concern is the DVI connection to the Mini Display connection on the Mac Mini. My understanding is that they are different.

LCD Monitor with B&W G3 Tower

Hello, I am looking to replace my 17" Apple Studio Display CRT on my G3 B&W Tower with an LCD monitor. My questions are: 1) Will my computer (VGA port) accept any current LCD screens on the market, or do I have to stay with Apple's LCD monitors? 2) There are several Apple Studio LCD Displays offered on eBay. They mention DVI and ADC connections. How do I know which models will work with my B&W G3? Forgot to mention that I have upgraded the processor with a Sonnet G4 500Mhz. Thanks.

Hi,
your B&W (like mine) should be equipped with a standard VGA output on your video card, which should accept any monitor with a VGA connection.
I tried a couple of LCD (a Samsung and a Hewlett Packard) which worked flawlessly and did not give me any problems.
I am not sure whether you can connect any of the current generation Apple flat screens due to the different interface, but you surely can take advantage of any VGA equipped LCD.
cheers

3 Monitors with 1 iMac and 2 Cinema Displays conected to Windows Gaming PC Help!

Hi
I want to set up a 3 monitor gaming set up with 1 iMac in the middle and 2 cinema displays either side. This would be a tripple monitor set up.
I am looking to set up a new computer and i want to have 3 monitors. I also want to have an iMac so i want the iMac in the middle and two cinima displays next to each other. i Want to also conect these monitors with a Windows 7 gaming PC.
I want to hook up my very powerfull windows 7 gaming computer wich has 3 SLI GTX 560 EVGA cards. These cards have a display port output.
So i want to run 3 monitors from my gaming machine and i also want to have my iMac use the 3 monitors aswell. I also want to take advantage of the full, maximum resolution. I would get the thunderbolt cinema display monitors.
Gaming comupter has 3 display ports so i need to connect each graphics card to one of the monitors. I then need to conect the two cinema displays to the middle iMac.
I have not bought anything yet i just need to know if i can do this. Need to know stuff like what adapers to buy and what compatabilties.
I need to know if this is posible and how i would do it.
Thanks

Could i use some of these cables?
It says they are thunderbolt conpatable.
http://www.macfixit.com.au/shop/index.php?_a=viewCat&catId=229
http://www.macfixit.com.au/shop/index.php?_a=viewProd&productId=2444

How to use two monitors with my Mac mini

Hello,
I have a Mac mini and using a 20" Samsung Monitor with it which works well. I also have my 40" LCD Samsung telly, set up next to it. Whenever i watch a DVD using my Mac i have to swap over the cables. Is there a way of getting the right cables etc and making it so i would be able to watch a dvd on the 40" and still use the 20" surfing the net etc. I had a similar set up with my old windows laptop, but cant seem to work out how do it with the mac. Both monitors have modern sockets, the 40in has HDMI/DVI IN and AGV, the 20" has AGV and HDCP/DVI IN. Many thanks.

To the best of my knowledge there is no way to use dual displays on the Mini. You may be able to find some adapter that will allow you to physically connect two displays, but they will be mirrored, not spanned.
To do what you describe would take spanning, which the Mini is not capable of doing. Unless something has changed recently,..

Can I use the HDMI out on a HP ALL IN ONE TOUCHSCREEN Desktop to connect a second monitor with HDMI

Can I use the HDMI out on a HP ALL IN ONE TOUCHSCREEN Desktop to connect a second monitor with HDMI in without any additional software or graphics adaptor. I have a 520-1070
HP - 23" Touch-Screen TouchSmart All-In-One Computer - 8GB Memory - 2TB Hard Drive ? I used a HDMI to HDMI cable and the monitor was not recognized.

Here are the specs for your HP TouchSmart 520-1070 Desktop Computer. As previously stated your computer Doesn't have a HDMI output, instead it has a HDMI input. This is designed to let you connect a game console, a DVD/Bluray player, etc. to use as a monitor.
If you wish to conect a second monitor to your computer, you will need to use a USB-to-video adapter such as the EVGA UV Plus+ UV39 or EVGA UV Plus+ UV19. Using an adapter like these with the touch feature of your computer may cause issues with pointer control and you may need to disable the touch feature to use "extended desktop".
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

How to use one monitor with two Power Macs

I searched this forum and was unable to find an answer. Although I believe it's probably here.
Nevertheless, I have a Power Mac G5 and a rarely used Power Mac G3. I'd like to share the G5's VGA Accusync 120 CRT monitor with the G3. I know there is a way to switch the monitor between computers without pulling plugs in and out of the machines.
Does anyone have any specific switch I could buy to solve this issue. I don't care so much for picture quality for the G3. But I don't want to compromise picture quality for the G5.

You're looking for what's called a KVM (Keyboard, Video, Mouse) switch.
This one should do what you're looking for. I've not used it, but it does VGA switching like you want and is inexpensive.

Can i have multiple monitor with my mac mini ?

Can i have multiple monitor with my mac mini like i do with my PC ? 2 differents screens.. not mirror.

There's lots of Mac Mini models since 2006 or so. What do you have?
Most support two monitors but how you do it is different depending on model.
Put this phrase into Google
dual monitors, mac mini
and you'll come up with the solution needed based on which MM you have.

Green shaded monitor with an R9 280x

Similar Messages

Maybe you are looking for