Grey screen during installation with Macbook Pro 13" I5 processor

I have a Macbook Pro with an I5 processor. I used software called Wipedrive to wipe my hard drive completely clean (I should have used the OS to wipe my drive). I tried to install the OS with a copy of Snow Leopard 10.6.3 that I purchased at Best Buy at about the same time I purchased my Mac. I hold the "C" key down while booting with my OS but get nothing but a grey screen. I have no options to acess files or folders when I boot up. I tried repartitioning with a disk I got from the internet. I even tried deleting the partition and installing without a partition (hoping the installation disk would give the option to partition). How can I install Snow Leopard to the hard drive without any Mac specific data on my hard drive. I have an early 2011 processor in my 6 month old Mac. Any help would sure would be appreciated as I have spent a lot of time on this.

You need a newer DVD than the one you have, such as the computer's original disks.
(62044)

Similar Messages

Grey Screen of Death on MacBook Pro Retina late 2013

Hi everyone, I decided to open this thread in order to help to other people that can encounter the same problem. Here's what happened to me recently: I have a MacBook Pro, late 2013 model, and I've been using it now for 2 months. Everything worked perfect, and yesterday, when I turned off the computer, and tried to turn it on, a grey screen with the apple logo and the spinning circle appeared and it didn't boot. I thought it's some temporary problem and I turned it off and try to boot again. No help, it got stucked again on the grey screen with the apple logo. It was extremely frustrating because I was in the middle of the job, and I couldn't go on. I tried all kinds of things I've found on forums, but none of them helped. Here's what I've tried: reset SMC, reset NVRAM, start in the single user mode, start in the verbose mode, run the apple hardware test, start in the recovery mode. None of this made my mac book again as before. The recovery mode however booted, and I could check my HD and verify it, repair permissions, but it had nothing to do with my problem. In the recovery mode I had 2 options that I though could be useful in my situation. The first one allows to reinstall from time machine backup, and the other one reinstalls the OS. In my case it's Mavericks OS. My backup was 3 weeks old and I didn't want to lose some files, so I decided (after 7 hours and a sleepless night) to go to Apple Genius. I wanted to make sure that my mac hardware is ok, and maybe get some useful information about what made my mac behave that way. The Genius guy could't really answer what the cause was, and when he tried to run some diagnostics, only some of them worked, and some other diagnostics didn't boot again. However, he said my computer is fully functional and maybe some OS Mavericks file got corrupted and that's why it couldn't boot. He suggested me to reinstall the Mavericks OS. My biggest concer was what was going to happen with my files, and it turns out that (in case your hardware is OK) the best solution is to reinstall the OS. It keeps your files and preferences. Since I didn't want to wait at the Genius bar, I took the computer and reinstalled the OS at home. The computer booted again!!! :-)
My advice to everyone that may have the same problem: if resetting SMC and NVRAM doesn't help, reinstall from the latest time machine backup if you have one. If you don't have it yet, get one :-) it's a must. If you don't have a backup, or you have some old backup and you don't want to lose your files like it was in my case, just do a fresh OS install. That's the fastest solution, it saves your energy and time.

Hi everyone, I decided to open this thread in order to help to other people that can encounter the same problem. Here's what happened to me recently: I have a MacBook Pro, late 2013 model, and I've been using it now for 2 months. Everything worked perfect, and yesterday, when I turned off the computer, and tried to turn it on, a grey screen with the apple logo and the spinning circle appeared and it didn't boot. I thought it's some temporary problem and I turned it off and try to boot again. No help, it got stucked again on the grey screen with the apple logo. It was extremely frustrating because I was in the middle of the job, and I couldn't go on. I tried all kinds of things I've found on forums, but none of them helped. Here's what I've tried: reset SMC, reset NVRAM, start in the single user mode, start in the verbose mode, run the apple hardware test, start in the recovery mode. None of this made my mac book again as before. The recovery mode however booted, and I could check my HD and verify it, repair permissions, but it had nothing to do with my problem. In the recovery mode I had 2 options that I though could be useful in my situation. The first one allows to reinstall from time machine backup, and the other one reinstalls the OS. In my case it's Mavericks OS. My backup was 3 weeks old and I didn't want to lose some files, so I decided (after 7 hours and a sleepless night) to go to Apple Genius. I wanted to make sure that my mac hardware is ok, and maybe get some useful information about what made my mac behave that way. The Genius guy could't really answer what the cause was, and when he tried to run some diagnostics, only some of them worked, and some other diagnostics didn't boot again. However, he said my computer is fully functional and maybe some OS Mavericks file got corrupted and that's why it couldn't boot. He suggested me to reinstall the Mavericks OS. My biggest concer was what was going to happen with my files, and it turns out that (in case your hardware is OK) the best solution is to reinstall the OS. It keeps your files and preferences. Since I didn't want to wait at the Genius bar, I took the computer and reinstalled the OS at home. The computer booted again!!! :-)
My advice to everyone that may have the same problem: if resetting SMC and NVRAM doesn't help, reinstall from the latest time machine backup if you have one. If you don't have it yet, get one :-) it's a must. If you don't have a backup, or you have some old backup and you don't want to lose your files like it was in my case, just do a fresh OS install. That's the fastest solution, it saves your energy and time.

Upgrading from Snow Leopard to Lion - couldn't complete as disk corrupt - went through everything - disk utulity, install disk etc. can't be fixed - grey screen - transferring data to macbook pro - unable to transfer photos - says locked volume - help

Hello - tried to upgrade to Lion (software all up to date) could not carry out as disk corrupt - tried to fix using disk utility, no luck, tried through install discs, noluck, screen went grey, went through all the troubleshooting steps advised - could get hard drive button up but wouldn't launch - took the last troubleshooting step (before wiping hard drive) and transferred data to MacBook Pro - all fine except for iPhotos - comes up as "locked volume" - have been through all the trouble shooting steps to all read/write access - file info says I have read/write access- any ideas - otherwise I have lost a bucket load of photos :-(
Thanks

See this tip if your data isn't backed up:
https://discussions.apple.com/docs/DOC-1689
In the future always backup your data before updating.

Grey screen and continuous beeping (macbook pro 2010)

Hi, I unplugged my computer from its display/keyboard/HDD setup to use it portably and then upon waking it from sleep - it froze and a continuous beeping began from within the computer.
When I started the computer I get the bong and white/grey screen (completely blank) and the beeping begins immediately. But thats as far as it goes.
I've looked online and there's a lot said about RAM related beeping but having removed the RAM i know this not to be the case as the beeping I hear is much quieter and far more regular than any of the loud RAM beeps.
Safe boot, pram reset and cmd s did nothing.
Any ideas whats wrong and how to solve?
Thanks

Hello there, whistler2014.
Sounds like you did some great troubleshooting already. You may just want to review the recommendations in the following Knowledge Base article to make sure you've covered all bases:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Screen stuck on gray, used shift key and my screen appears with MacBook Pro and not the recovery option. Please help

Screen stuck on gray, used shift key and my screen appears with MacBook Pro and not the recovery option. Please help!

Hi ..
Shift key boots into Safe Mode, not Recovery.
This only works on a Mac running v10.7 Lion or later.
Startup your Mac while holding down the Command + R keys. From there you should be able to access the built in utilities to repair the startup disk and restore OS X using OS X Recovery
If you can't boot into Recovery Mode, help here > Mac OS X: Gray screen appears during startup

After upgrading to Yosemite, I am unable to share screen with Macbook Pro

After upgrading to Yosemite 10.10 on a 2008 MacBook Pro I am unable to "Share Screen" using my authorized user account. It worked fine before I upgraded to Yosemite.
I can access "Share Screen" by "requesting permission", but of course this doesn't work unless I am sitting right by the MacBook Pro to give myself permission, which defeats my original purpose for using "Share Screen".
I attempted to add another authorized "Share Screen" user account, but was unable to access the list of add "Groups and Users" on the host MacBook Pro from the "Share Screen" dialog box. The dialog box pops up, when I press "+" to add another user, but the list of users fails to appear. I assume the list of authorized users for screen share has somehow become corrupt.
All other ways to access "sharing user" accounts appear to be working properly. I can add and remove other "sharing users" without problems. For example, I can add a new authorized "file share" user and share files without problems.
I ran Disk Utility in Recovery Mode and normal mode and corrected all errors, and user permissions on both machines. I also ran "resetpassword" from Terminal in Recovery Mode and "reset" user permissions. I am not an experienced Terminal or Recovery Mode user though.
I also tried turning the Firewall off, to no avail.
I am attempting to access "Screen Share" on the MacBook Pro via a Macbook Air 13" manufactured mid 2013 also with Yosemite 10.10, however, I also attempted with an older MacBook Air which experiences the same problem.

Thanks for the idea but it did not work, I do not know why it is asking me for a password which I never needed before for a guest to use the computer? I have tried everything and I do not know which password it wants? I do not see any option for a password for the guest account, to create one or delete one or modify it? Maybe this bug\problem will be addressed in a future update?

Screen Issues with MacBook Pro (Static Lines)

Hey guys. I aam having problems with my Screen/Display on my Macbook Pro.
Static lines appear aprox 1/3 of the way in from the right side. The lines run horizontally about 1 inch in length and running vertically all the way down the display. A screen shot shows a normal working display. Took a pic of the problem:
I cannot run hardware tools. My computer did not come with a disc and I know they are only a shipping charge but I do not have even $5. I am a student and this is my only way to do my schoolwork. The Screen (inner display and outer protective screen) was replaced by Apple in May '12. The 1 yr warranty ran out in June '12. When the screen was replaced it started doing this as well, but had not gotten this bad. There are now 2 where there was only one yesterday. I am wondering if it may be the cable as moving the display often fixes or produces the problem. I know the cable is not very expensive and not to difficult to replace.
Here is the info on my Mac:
Nice Name:
Machine Model: MacBookPro9,1
Name: MacBook Pro (mid 2012) 15 inch
Family name: A1286
Model Number: MD103
Group1: MacBook
Group2: Pro
Generation:
CPU speed: 2.3GHz
Screen size: 15.4 inch
Screen resolution: 1440x900 pixels
Colour: Aluminium
Production year: 2012
Production week: 13 (April)
Model introduced: 2012
Memory - flavour: DDR3-S-1600
Memory - number of slots: 2
Memory - maximum total: 16GB
Memory - largest module: 8GB
Factory: C0 (Quanta Computer (Susidiary = Tech Com))

It is getting worse in the sense that it is occuring more often and taking longer to resolve. Moving the laptop lid/display would typically fix the prblem in the past but now it is hit or miss. Even vibrations will cause the issue to occur or resolve. We are leaning more towards the issue being a cable and not the display. Since taking a screenshot produces a pic without issues I would gather that the video card is fuctioning properly. I welcome any comments on this.

I have just used air display with macbook pro. i have disconnected now from apple tv. but my laptop screen is still very small like its connected to the tv. this means all the tabs and writing is very small, how do i full disconnect my laptop?

i have just used air display with macbook pro. i have disconnected now from apple tv. but my laptop screen is still very small like its connected to the tv. this means all the tabs and writing is very small. like the display down the bottom where al the applications are, is n the middle of the page and not spread down the bottom. this is seriously annoying! all the writing is every small and the tabs are small and its hard to read. the air display link has disappeared from my computer. but the laptop screen is still very small. i want to know how do i get rid of this and return my macbook screen to its normal size. thank you

Hello chrispyw,
If your content is still being displayed incorrectly, I would check the resolution setting for the built in display with this article:
OS X Yosemite: Adjust your display’s resolution
If it keeps happening whenever you use AirPlay then I would use this section of the following article to reset the display system:
Apple computers: Troubleshooting issues with video on internal or external displays
Reset the system
You can reset the Mac's parameter RAM and SMC.Reset the resolution
Start by resetting the Mac's parameter RAM. If the display does not come up, was previously set to an unsupported resolution, and still results in no video:
Start up in Safe Mode.
From the Apple () menu, choose System Preferences.
Choose Displays from the View menu to open the preferences pane.
Select any resolution and refresh rate that your display supports.
Restart your computer.
Thank you for using Apple Support Communities.
Regards,
Sterling

Replace the Glossy Screen with the Matte Screen on a 2008 Macbook Pro?

Can you replace the Glossy Screen with the Matte Screen on a 2008 Macbook Pro?
Where would I get a Matte Screen for a reasonable price if I could change it?

There are a number of issues you should consider before embarking on this project.
1. If you have a late-2008 unibody MBP, you are undoubtedly aware that there was never any anti-glare option offered for that machine. So there is no anti-glare display that was made to work with it.
2. If you choose to replace only the LCD panel and not the entire display assembly — which is probably feasible but involves a great deal of painstaking work — you will also need to buy (separately) the aluminum bezel that takes the place of the glossy cover glass panel in models that came equipped with the nonglare screen. The bezel covers and protects the edges of the LCD and the delicate electronic connections there, and hides all that from view.
3. If you go that route, you will have to make sure that the cabling related to the display you are installing is identical to the cabling related to your original display. This means checking to make sure the cable lengths, connectors and routing both within the display assembly and hinge cover and within the lower case of the computer are all the same.
4. If you choose to replace the entire display assembly with one that contains a nonglare LCD, you will have the entire, intact glossy display assembly available to sell afterward. If you replace only the LCD panel, the LCD and glass cover panel that you remove will have much less resale value and are likely to be much harder to sell at all, because you won't practically be able to offer any warranty with them and because there are probably far fewer people willing to tackle the fussy, risky display disassembly process than are willing to replace the whole assembly as a unit.
5. Even if you choose to replace the entire assembly, you will need to verify that the cables dangling from the replacement display assembly are the right lengths and have the right connectors to tie into your lower case properly. Because the assembly will have come from a later MBP model than yours, cable routing and connectors may have changed from one to the other.
If this all sounds more daunting than you were expecting, you may want to consider just applying a nonglare film to the glass covering your present screen. If you aren't happy with the results, you can fall back on the replacement option.

I'm getting the grey screen during start up and can't boot the computer. I did a cmnd R but worried it would automatically wipe my hard drive and reinstall OS. Is there a risk at cmnd R will result in wiped HD without me actively making that choice?

I'm getting the grey screen during start up and can't boot the computer - MacBook Pro with lion.
I did a command r after doing some research but got nervous that it would automatically wipe my hard drive and reinstall OS.
I was nervous because it asked me for language for software use before any options were presented (such as repair via disk utility). It looked similar to an OS install.So I powered off....Is there a risk at command r will result in wiped HD without me actively making that choice?

Repair the Hard Drive and Permissions - Mavericks, Lion/Mountain Lion
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall Mountain Lion or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is
three times faster than wireless.

Apples update didn't work for me: Boot Camp: iMac displays a black screen during installation of Windows 7

Boot Camp: iMac displays a black screen during installation of Windows 7 - Apple Support
I have followed each of the steps listed in the link above with no success.
Prior to adding the extra drivers I was able to start the Windows install process up to reformatting the "Windows" Bootcamp drive. After that the computer would go through some instal processes and eventually restart. After the restart the screen would go black. The black screen lead me to the Apple Support link above dated March 5 2015. After going through steps listed in the link above, I get an error message stating that the D:\Sources\instal.win. file cannot be located. I am forced to restart the computer at that point and theWindows install process attempts to start again but always ends up at the same point.
Note: I am installing windows 7 Pro from a DVD. I scanned the AutoUnattend.xml file and noticed that it refers to "Windows 7 ULTIMATE" but not "Pro" or any others that I could see. (see below). Could that be part of the issue?
Any feedback would be greatly appreciated.
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
</unattend>
iMac (27-inch, Late 2009)
2.66 GHz Intel Core i5
16 GB 1067 MHz DDR3
ATI Radeon HD 4850 512 MB

Here is an over-simplified explanation of WIM and CLG files. Assume your DVD Media contains
W7- Ultimate
W7- Professional
W7- Home Premium
W7- Home Basic
WIM Files
File1
y
y
y
y
File2
y
y
y
y
File3
y
File4
y
y
File4
y
y
y
The File .wim will contains a compressed image which contains File [1...5].
The W7-Ultimate .clg will have 5 entries, with all set to 'Y'.
The W7-Professional .clg will have 5 entries, with 'Y','Y','N','Y','Y'.
The W7-Home Premium .clg will have 5 entries, with 'Y','Y','N','N','Y'.
The W7-Home Basic .clg file will have 5 entries, with 'Y','Y','N','N','N'.
This allows a single .wim Image file on the DVD media to be used to install any of the 5 flavors of Windows. When you enter your product key, the Installer knows what specific W7 variant you have the key for and will tell the WIM to extract the specific files the installer needs to be extracted.
The following line
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
is telling that a retail product key will be entered, which should go look for this specific .clg file (from the five you already have on disk). You can test if it will work for you by changing this line to the following
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 PROFESSIONAL" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
If it does not work, the other issue can be related to device discovery. Typically A: and B: device names are reserved for Floppy Drives. C: is your internal HDD.
D: can either point to the Optical drive, or the USB. The normal convention is that the removable media is named from Z: backwards. Y: and Z: are usually used for Network drives, so X: should be your USB. First try with the change to "Professional". If it does not work,

There's a soft white dot on the screen of my new MacBook Pro Retnia

There's a soft white dot on the screen of my new MacBook Pro Retnia That is visible especially when the background is light. It isn't a sharp dot but rather a soft blurred looking dot. Does anybody else have something like this or does anyone know what it is? I'm thinking its s dead pixel but it doesn't look like one that i've seen on other lcd displays.
I set my desktop background to a 50% grey and that's how I found it. Now that I did, i can't stop looking at it. I tried to take a pic of it its in the center of the photo. Its not easy to see on the photo but, its very easy to see on the display. Oh and its not dirt or something on the surface. Not sure if i should go to the genius bar on it. I am worried that it may get worse. Any input is appreciated.

I also had this problem, same make and model and specifications as you have. Brought it into Apple and also called them about. They stated they have not heard of this yet although I find that hard to believe with the # of cases on this being reported. Must have been a bad lot or batch of Retina MBP's that were made and this got by quality control. But they were okay with giving me a new one on the spot.
As you said, doesn't show on darks but on whites; oh boy it sure does and it is annoying on photo editing and documents where white is all you see; about 1.5mm x 1mm big and bright like a little star. Very hard to detect at first unless you have the white background up as wallpaper.
I sent my MBP back for a replacement and told them I did not want a repair on a computer that was less than 3 weeks old. Stuff happens and no one is perfect so long as Apple and their resellers stand by and make amends by issuing new MBP's. I did not buy mine via Apple direct this time, but rather used a authorized Apple reseller and fortunately they agreed to issue a new one. Keeping fingers crossed.

How do I take a screen shot on my macbook pro?

How do I take a screen shot on my macbook pro?

Press the Shift, Command, and 3 keys to capture the whole screen.
Press the Shift, Command, and 4 keys to capture a draggable part of the screen, or follow it with the spacebar to capture a window.
Open the PNG on the desktop. Alternatively, combine either of the above with the Control key to put the screenshot onto the clipboard instead of the desktop.
(104403)

Everything keeps freezing/crashing after Mavericks installation on MacBook Pro

Everything keeps freezing/crashing after Mavericks installation on MacBook Pro.
It started with Photoshop, then Safari, and now the Kinect sensor.
Mavericks is the worse thing that happened to me I have a thesis project to work on!
What can I do?
How can I remove Mavericks and go back to Mountain Lion?
Thanks

Hey StephSassine,
First, I would run through these steps:
Your computer’s startup disk may not have enough free disk space. To make disk space available, you can move files to another disk and then delete files you no longer need on the startup disk:
Increase disk space
http://support.apple.com/kb/PH10677
If that doesn't work, you may need to repair your computer’s disk in Disk Utility:
Choose Apple menu > Software Update to make sure you have the latest version of Mac OS X.
Software updates sometimes change a file’s permissions to improve security, so updating your software can solve some permissions problems.
Open Disk Utility, in the Utilities folder in Launchpad.
Select the disk you want to check.
Click First Aid.
Click Repair Disk Permissions to test and repair permissions.
via: Disk Utility 12.x: Repair disk permissions
http://support.apple.com/kb/PH5821
If that doesn't help resolve the issue, you can revert to a previous OS X version:
OS X Mavericks: Revert to a previous OS X version
http://support.apple.com/kb/PH14176
Sincerely,
Delgadoh

Using Thinkpad Trackpoint USB Keyboard with MacBook Pro, Air, Retina (with pictures)

Using Thinkpad Trackpoint USB Keyboard with MacBook Pro, Air, Retina (with pictures)
The purpose of this discussion thread is to:
(1) Get community thoughts around using alternative and complimentary mousing approaches with MacBooks
(2) To share a current and searchable set of resources for those interested in leveraging a best-of-both-worlds approach for using a non-Apple Trackpoint Keyboard with an Apple MacBook.
(3) To level-set the fact that a Thinkpad Trackpoint USB Keyboard works with MacBooks automatically and instantly out-of-the-box.
Note: I created this discussion because I found that all the other discussion threads related to using a Thinkpad Trackpoint Keyboard with MacBooks were archived and therefore I could not post my thoughts there.
I have been using MacBooks for 3+ years now. Airs, Pros, Retinas etc. I LOVE the built-in MacBook Apple Trackpad. It is wonderful. Apple has no equal as far as Trackpads go.
In addition, I have been using the Thinkpad Trackpoint USB Keyboard with my MacBooks for ~2 years, and below is why I have found BOTH the Apple Trackpad and Thinkpad Trackpoint to be great.
The Trackpoint and Trackpad both have their sweet spots. Personally I use the built-in Apple Trackpad on my MacBooks when I'm using my MacBook for less than 1 hour, loosely speaking. If I am going to be heads-down for more than 1 hr writing, reading, surfing, graphic designing, programming, workshop facilitating, teaching, mindmapping, presenting, demoing, etc. then I pull out my "Lenovo Thinkpad USB Keyboard with Trackpoint (55Y9003) > https://www.google.com/search?&q=lenovo+thinkpad+trackpoint+usb+keyboard
I know many will laugh at me for using a Thinkpad Trackpoint Keyboard with a MacBook... Keeping an open mind, let's just agree that there is historical precedence for alternative mousing devices. If I could only choose one, I would use the Apple MacBook built-in Trackpad exclusively, however with alternatives come potential benefits. Keep in mind that Apple, Microsoft, Logitech and many other companies make millions of dollars each year providing alternative peripheral devices for computers, and mousing is no exception. Regardless, I just want to share my positive experiences using both. :-)
Why should you care? For *some* people the following is true and meaningful. The Trackpoint (the little red eraser head stick thingy) in the midle of the keyboard enables useful and unique dynamics/use-cases, including:
You don't have to take your hand(s) off the keyboard to mouse
You can independantly click without accidentally moving the mouse (Yes I know some people don't have issues with this)
You don't run out of finger-gesture runway when you're moving your mouse across the screen (I know this is a gray area for some people)
For mouse-movement-heavy applications (e.g. Graphics, drawing, etc.) the Trackpoint *is at times* more exacting
Below I share some pictures (which I know *look* ridiculous to some people, but none-the-less help demystify what this looks like. And, while ridiculous looking, it is actually quite thin and elegant once you get over the initial shock of seeing these two diverse technologies combined in this way.
Rest assured, the keyboard shown below (google "55Y9003") is VERY light, thin and fits in almost any laptop case/backpack easily so it is not a big deal to carry it, if you work on-the-go. In addition:
It is UNCANNY how well it fits on top of the keyboard space of all MacBooks.
It fits perfectly around the corners of the MacBook Pro/Air/Retina keyboard
Note: I took one of the 5 rubber feet/pads off the bottom of my keyboard, the one in the middle
Lastly, you can actually use the built-in Apple Trackpad at the SAME TIME as the Trackpoint Keyboard.
It is quite a nice best-of-both-worlds approach for people that like the benefits of the "Why should you care?" use cases above.
Please reply and comment with your thoughts and please let's keep it positive, constructive and friendly :-)
Pictures Below:
My two Retina MBPs, one with and one without the keyboard, so you can easily see the difference. (As if you wouldn't)
A slightly closer-up shot of just the RMBP with the Trackpoint Keyboard on top
Please reply and comment with your thoughts and please let's keep it positive, constructive and friendly :-)

Newer Bluetooth version of the ThinkPad External Trackpoint Keyboard available...
The new version is smaller, so you can use your MacBook Trackpad at the same time as your Trackpoint keyboard.
Here is the Lenovo model/Part Number# 0B47190
Here is a picture of what it looks like:
Note: Just like the older larger USB model keyboard, there is a rubbery footpad in the middle of the bottom of the keyboard that I just peeled off. Otherwise, it makes the "H" key press accidentally under-neath the keyboard. Once I took that off, it fit perfectly over and around the built-in MacBook keyboard, so I can optionally put it on top of my MacBook for easy typing. :-)

Grey screen during installation with Macbook Pro 13" I5 processor

Similar Messages

Maybe you are looking for