Grey Screen & Grey Apple w/small timer running.
Hello to all. I am loss in this new challenge. I have a Grey G4 Power Mac which has not given me any problems until 3 days ago. I turned the power on and all I saw was Grey screen, grey apple and the timer running forever in a circle. Tried restart to no avail. Checked all connections and unplugged it from the power source as it would not shut off using the power button. Tried booting up from Tiger CD to no avail. Reseated the memory card and pushed the reset button, no change. Ok,time to go to the Mac Guy. They tried running Disk Warrior and it would only go to a certain point and it got a error message. They retrieved data from the hardrive, zeroed out old one and tried re-install of Tiger. It would not work even using 3 different CD's. They put a new hardrive w/Tiger pre-installed. It would boot but not take any updates, did the same with the old one and with the same result. Changed out the memory card, same results. Then put the new hardrive back in with all copied info, Tiger and updates. Zeroed out the old one and tried to copy from the new one and it came up with a Volumn Error Message. They are now saying it may be the logic board. Does anyone have any words/ideas of wisdom? Too much money and time to keep second guessing. I appreciate any help/time.
Lorin, Welcome to the discussion area!
Start your troubleshooting with KB 106464, Your Mac won't start up in Mac OS X.
Similar Messages
-
Computer won't start, grey screen with Apple logo only. Ideas?
Last night my wife's G5 froze. It is a G5 2.0 running OS X 10.4.11. I shut it down (had to use the power button) and tried to restart. No luck, just made it to the grey screen with Apple logo and spinning wheel. After a few seconds the Apple logo disappeared and a black box took its place, then the wheel stopped spinning. It was late, decided top wait until morning before trying again.
This morning I tried to start up again. This time got a warning(?) in upper left that a Firmtek item had already started. I'm sorry I didn't write this all down at the time, so I don't remember the entire message. Since there is a Firmtek card installed in one of the PCI slots I thought that might be the problem, and I pulled the card, as well as another Adaptec card that was also installed. Tried to start again, got to grey screen with Apple but this time no spinning wheel.
Opened media slot manually and inserted Diskwarrior. Tried to start with Diskwarrior but again only reached grey screen. Let run for ~5 minutes, until fans started to run and were begining to get noisy.
Next I reset the PRAM. No luck, still stuck on grey screen. Tried Diskwarrior again, this time got another message in upper left. Here is most of it -
System Failure : cpu=1; code=60000009 (Invalid pmap)
Lateset crash info for cpu1;
Exception state (sv=0x609bb280)
PC=0x000a4ad0; MSR=0x02003000 followed by more similar strings, then
backtrace terminated - unaligned frame address; 0xfc088891
So what's the diagnosis? I've had various issues with my G5s in the past, but have never had one refuse to boot with Diskwarrior before.
Thanks in advance for any help!Whew, could be many things, from RAM, (or RAM slots/solder issue), to CPU #1 being bad, (CPU#1 is actually the second one.
Does it boot into any of these modes?
Target mode...
http://support.apple.com/kb/HT1661
Does it boot to Single User Mode, CMD+s keys at bootup, if so try...
/sbin/fsck -fy
Repeat until it shows no errors fixed.
(Space between fsck AND -fy important).
Resolve startup issues and perform disk maintenance with Disk Utility and fsck...
http://docs.info.apple.com/article.html?artnum=106214
We might get clues with verbose mode...
http://support.apple.com/kb/HT1492 -
I Shut down my Mac by holding in the power button after my iMac froze and now when I try to turn it back it on all I get is the grey screen with Apple loge and the timer and doesn't get any further. I have tried the diagnostic test but nothing was found.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Hello my MBP 15" stops at grey screen after apple logo disappears
hello, my MBP 15" stops at grey screen after apple logo disappears, what can i do about this? ive tried booting into safe mode but screen turns blue with black lines also tried resetting NVRAM and PVRAM but still stops at grey screen, also tried using applejack, it shows no problems at all, says my disk volume is ok but the screen still stops at grey during start up, havent tried the installation disk thing because i dont have my installation disk with me
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My macbook pro 2011 shows grey screen with apple logo and want start
i was just using my macbook pro and it freezed for a while not responding and i turned it off by pressing the power button. afterwards, i turn it on and it shows a grey screen with apple logo but want start pls somebody help me because am having "my life" on the machine
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. -
My macbook pro is stuck on grey screen with apple symbol in center with the progress circle under it continusly spinning. After I had turned it on. Prior to turning it on I had to force close and shut down a few hours prior. Please Help I have tried everything I know to do
Unfortunately this means that there is a problem in the boot sector of your hard drive. It might be indicative of a fundamental corruption in the coding that allows your computer to boot your operating system from your hard drive. I had this problem twice and it resulted in me having to get a new hard drive and restore my data.
In other words, your computer can't talk to your operating system so you can't access your data.
Here is my advice: DON'T CALL APPLE TECH SUPPORT though they are kind and usually helpful it will take you an hour just to explain the situation and they will only tell you to do what I'm gonna say here.
First: Shut down your computer completely
Two: boot up while holding down the following keys: command, option, p, and r. The computer will reboot 3 times. This solution will likely fail so if you're frustrated skip to the next step.
Three: Boot up while holding down the option key. Select recovery drive. Select your default language. Select disk utility, click on Macintosh HD, and select "verify and repair volume." Likely the verification will produce some line like "unused node not erased." Or something like that. If anything using the words "node structure" comes up, you need a new hard drive.
If after verification and repairs you still can't boot I sincerely hope you have apple care because you will need a new hard drive. Set up an appointment to come in to the apple store, they will tell you to go and get data recovery, just ask them to give you the old hard drive. Unless you have an up to date backup in which case you can just restore from that. If you're lucky the only issue is with the boot sector which means that if you ask them to give you the old hard drive, you can buy an enclosure and you have effectively been given a free external hard drive. It still works to store data just not to load an operating system.
If you have a back up drive bring it to the apple store and they'll do the whole thing right there, it should take around an hour and a half but may take longer.
Hope this helps, it's annoying but it's your safest bet.
All the best. -
My macbook pro doesn't bootbeyond the grey screen with apple icon and spinning wheel.
My macbook pro doesn't boot beyond the grey screen with apple icon and spinning wheel. I used the "Option" button to access the Disk Utility function and run Repair Disk and Repair Disk Permissions. Should I restart my computer?
The following support article is somewhat outdated. Where it refers to booting from an installation disc, you should boot from your recovery partition (if running 10.7 or later) by holding down the key combination command-R at the chime.
Mac OS X: Gray screen appears during startup -
Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?
Unfortunately do not know the operating system since I never updated anything and I can't get in to it.
Thanks for your assistance.If you want to preserve the data on the boot drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data. -
Grey screen with apple logo after new HDD install
I have a mid 2010 iMac A1312, this was given to me recently with the knowledge of its bad HDD, so I bought a new HDD. I followed step by step instructions on how to replace a Hard drive and I did. I switched the computer on and inserted my Snow Leopard 10.6.3 install disk and clicked the icon. It is now at a light grey screen with a dark Apple logo. I have waited about ten minutes and restarted the machine. Ive tried all variances of startup holding down c, option, command r and so forth. Currently I am going to give it a good long wait of 20 minutes or so and see if I was just being impatient and not allowing the install software chance to start up. But in the mean time... any suggestions? I have read I need the original disks that came with the computer from factory to get a new HDD going. Is this true? thank you for your time!
it has now been 30 minutes and no change. I still have the grey screen with apple logo. please help
-
Grey Screen with Apple Logo - HELP
First of all: I know there is another topic for this, but this is a different problem (i think?)
I was installing snow leopard... it came up with that green tick with restart below it. It shut down and when it booted up it went to the grey screen with apple logo and it hung there for 6 hours until I turned it off. The disc is still stuck in there (tried holding in the mouse button) and it won't come out. I also held in the C button which made the disc drive make a lot of noise.
Any help would be appreciated.Here there is a lot of topic about that subject.
By any change, have you completed all upgrade that your mac asked you before installing 10.6?
If yes, you're in this situation: http://support.apple.com/kb/TS2990 , you can try to install it again. Some people said that it took them 3 times to make it works. -
Can't get past grey screen with apple spinning wheel, had a loading bar for a few seconds?
HElp, can not open my Mac. Stuck on grey screen with apple and spinning wheel?
PReviously opened fine but I could not remember my password try a number of passwords. I now know my password but when I turned it off and back on got this screen?THe command R took me to a dark scree with Mac OS X Utilities with 4 choices
REstore From Time Machine Back Up
REinstall Mac OS X
GEt Help Online
DIsk Utility
HElp -
grey screen no apple followed by blue screen with vertical lines. Graphics and logic board replaced <6 months ago. What to do? I held down shift, it gets HOT HOT and makes noises. (for safety mode) followed by a blank grey screen and blue screen. Then tried the other way (sorry, I think it's command alt delete? I don't remember) and it turned from grey (no apple symbol) to blue blank. Then third time, grey followed by blue with vertical lines, not blocky clear lines that you can see if you are close to it.
Thanks for any help!You have to take the computer to the Apple store to have it checked out.
Genius Bar reservation
http://www.apple.com/retail/geniusbar/
Best. -
Retina MBP, grey screen of death (GSOD) 3 times in first 4 days. Hardware issue?
I just picked up a Retina MBP 4 days ago. So far I've mostly just done light web browsing on it (using Google Chrome Canary), maybe ten hours of total usage. It's died to the Grey Screen Of Death (GSOD) three times so far. Is this likely a physical hardware issue, or are there some software kinks they are working out? Should I try to return it within 14 days, or take my chances getting it fixed if it turns out to be a hardware issue?
This is my first mac (previously all thinkpads), and I have to admit that if a windows laptop BSODed on me three times it would be in the return mail, and I wouldn't even bother to re-order. This is because I have enough experience with windows to know that three BSODs doing nearly nothing is absolutly a hardware problem. What's it like on the Apple side of the fence? Is this probably a hardware issue, or possibly poor quality control on drivers?Digging in a little deeper, I found the location of the kernel panic logs, and all three of them look like they are the same Intel HD4000 driver bug ticked by Google Chrome which is talked about here.. Perhaps it's not bad hardware after all.
https://discussions.apple.com/thread/4086406?start=0&tstart=0 -
Need Help For iMac G5 Stuck On Grey Screen Or Apple Logo No Spinning Gear!
Hello everyone i'm new here and i'm new for using iMac for some reason i was trying to clean or to fresh installation the iMac that my brother gave it to me that he bought it into the flea market without the original disk on it! when i erase the Macintosh HD and some of the partition o iMac then reboot it now the iMac stuck on grey screen or apple logo no spinning wheel shown. and i also try to search and try all the tips of all mac user's like all the command key's and follow the instruction of them but still nothing happen..
Holding CMD & R just to go disk utilities nothing shown up only apple logo and the noisy fan.
Holding alt and it go to blue screen and show my mouse Pointer Refresh Logo, Hard drive Icon, Arrow Sign.
i can click Arrow Sign and it go Apple Logo and within 2-3 seconds and it change to Power Sign Logo,
i can click Refresh Logo but nothing happen .
i can't click the Hard Drive icon.
CMD, Option, P & R to Reset i also try and it's the same nothing change.
CMD, Option, ESC no action shown.
Is there anyway to fix this issue or problem please and thank you for help.
Hoping to get result for all of you guys P.S
iMac G5
v10.5.8
LeopardYou need to have the install DVD that was issued with the iMac
You can call Apple at 1-800-275-2273 -
I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?
Maybe this might help.
http://support.apple.com/kb/TS2570
Maybe you are looking for
-
I just downloaded the trial version and can't see anything that says initiate or upload to get images - also keep getting that darned error message. I use MAC OS X 10.7.5
-
IProcurement Requisition Details - Results in Error Page
Hi, Clicking on our requisition details or view my requisitions results in a error page, any ideas why this occuring? Exception details: oracle.apps.fnd.framework.OAException: java.lang.NullPointerException at oracle.apps.fnd.framework.OAExceptio
-
http://www.sbcforums.com/forums/ It's EXTREMELY annoying. >.>
-
Filtering of ToDos in Apple Mail
I'm impressed with the ToDo view in the new Mail 3.0. However, I can see no way of filtering the list. In particular, I am attempting to hide completed ToDo items. I've searched the menus and interrogated the Help file without success. I cannot belie
-
Change owner for transport from an external system
Hi Everyone, I have some transports that were brought into our DEV system from an external system. (They're BSI transports but I don't think that detail is important.) We are using a third party transport management system (Insite) and in order to