Grey screen with question mark on folder?

Just turned on my MacBook and it opened up with a grey screen with a folder in the middle with a question mark, what does this mean?  I am also hearing a clicking sound from inside the computer.

frederic, with due respect: this solution is good if the disk is good, if the disk is dying, therefore ? is not due to a corrupt system, but a dying disk, then this solution may impede later recovery of data, which is still possible, if need be and if the disk is not entirely dead. Usually they do not not die over night.

Similar Messages

  • Grey screen with question mark on boot up.

    My son's 2011-12 Macbook Pro displays a grey screen with a question mark and will not boot.  I pulled  that first drive, put that first drive in a USB cage and connected the USB cage  through a USB port and could boot a different machine with the first drive.  I put a brand new second drive with a formatted and journaled OSX drive in place of the original first drive in my son's macbook pro machine tand got the same grey screen and question mark.  Do I need a new electronics board?  If so that is a $500 repair and not worth it on a 3 year old machine.  Thoughts?

    It could be anything at this point - most likely, it seems, is that you've a faulty SATA cable. If you go to www.ifixit.com you can find the Apple part number for the cable (or buy the cable at ifixit, even) and search eBay for the part number (much less expensive on eBay and I've yet to hear of one from eBay having failed).
    I'm betting that's the problem.
    Clinton

  • TS3423 my start drive not responding. getting grey screen with question mark in a folder. when i use disk utility drive wont mount

    When I turn on my Mac I get a grey screen with a folder with a question mark . Have tried the disk utility to no avail as the disk has apparently dismounted and will not mount even though the mount option is available. I have recently upgraded from snow leopard go os x maverick

    This could be a software/state problem or a hardware problem.  In your case it sounds like the latter but you should try the steps below in case it might help.
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/kb/TS2570

  • Mac OS X Leopard not working (grey screen with question mark appearing)

    Hello. I have a Desktop Mac Running on Leopard (not Snow Leopard) and it gives me the grey screen with a question mark. It has been doing this for a month now, and i had to restart it holding the C key every time, and now it has stopped working. I am using a Logitech mouse and keyboard, and had a disk inserted so i cant insert the installation disk. What should i do?

    You will have to reinstall OS X. Connect the original keyboard and mouse. Restart the computer and hold down the mouse button immediately after the chime. This should force the optical drive to eject the disc. Otherwise see the following:
    Five ways to eject a stuck CD or DVD from the optical drive
    Ejecting the stuck disc can usually be done in one of the following ways:
    1. Restart the computer and after the chime press and hold down the left mouse button until the disc ejects.
    2. Press the Eject button on your keyboard.
    3. Click on the Eject button in the menubar.
    4. Press COMMAND-E.
    5. If none of the above work try this:
    Open the Terminal application in your Utilities folder. At the prompt enter or paste the following:
    /usr/bin/drutil eject.
    If this fails then try this:
    Boot the computer into single-user mode. At the prompt enter the same command as used above. To restart the computer enter "reboot" at the prompt without quotes.
    Once the disc has been removed you can try to do the following:
    How to Perform an Archive and Install
    An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
    1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
    Repairing the Hard Drive and Permissions
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then quit DU and return to the installer.
    2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
    3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
    4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
    5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
    6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

  • How do I fix grey screen with ? Mark Blinking

    Please help me to fix grey screen with ? Mark blinking thanks

    The support article linked below is somewhat outdated. Where it refers to starting up from an installation disc, you should instead start up in Recovery mode.
    If you don't have a current backup of all the data on the startup volume, and you want to preserve that data, then you must try to back up before you do anything else. Ask for instructions if you need them.
    A flashing question mark appears when you start your Mac

  • Grey screen with question in folder

    The color wheel would not go away after several minutes.  I turned off the MacBook and then turned it back on .  I got a grey screen with a flashing folder with a ? In the folder.
    What do I do?

    It looks like your hard drive has disappeared. Could be any number of reasons, including a dead hard drive.
    If you can, I suggest you make an appointment at an Apple Store genius bar, and ask them to diagnose the problem. That service is free.
    http://www.apple.com/retail/geniusbar/
    You will have to pay for repairs, unless the Macbook is under warranty.

  • Re iphoto: when I double click on a thumbnail i get e grey screen with exclamation mark..can't access my photos to edit, order prints etc

    Was wondering if anyone can help...I am not very computer friendly but want to be able to edit my photos, use them as jpegs, order prints etc. When I double click on a thumbnail ( am presuming the thumbnails are the small photos ) I get a grey screen with an exclamation mark on it. I cannot drag the thumbnail onto the desk top it just pings back. This doesn't happen with all the thumbnails and has been a problem since we upgraded to snowleopard. I recently reinstalled photos from the memory card from my camera and they are alright. I am presuming that the old photos are stuck in there somewhere if only I knew the right buttons to press to get them out. Thanks, Jane Thomas

    Easiest: Restore from your back up.
    Otherwise:
    Try these in order - from best option on down...
    1. Do you have an up-to-date back up? If so, try copy the library6.iphoto file from the back up to the iPhoto Library allowing it to overwrite the damaged file.
    2. Download <a href="http://www.fatcatsoftware.com/iplm/"><b><u>iPhoto Library Manager</b></u></a> and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
    Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.
    3. If neither of these work then you'll need to create and populate a new library.
    To create and populate a new *iPhoto 6* library:
    Note this will give you a working library with the same Rolls and pictures as before, however, you will lose your albums, keywords, modified versions, books, calendars etc.
    Move the iPhoto Library to the desktop
    Launch iPhoto. It will ask if you wish to create a new Library. Say Yes.
    Go into the iPhoto Library on your desktop and find the Originals folder. From the Originals folder drag the individual Roll Folders to the iPhoto Window and it will recreate them in the new library.
    When you're sure all is well you can delete the iPhoto Library on your desktop.
    In the future, in addition to your usual back up routine, you might like to make a copy of the library6.iPhoto file whenever you have made changes to the library as protection against database corruption.

  • Boot error with question mark on folder icon

    Hello.
    This is very newest iMac (2014 late).
    It worked very first time with basic way.
    But 3 days later, iMac doesn't boot at all.
    I've tried everything about reinstall and boot
    Internet recovery, P+R+Alt+Cmd, recheck and verify hard drive.
    However, sometimes There's no show hard drive on disk utility mode.
    Can't even erase or format because I don't see it on hard drive list.
    And now after power on, there's only [question mark on folder icon] and
    it looks like warning me something.
    Should I refund it? Or try something else?

    Hi
    Given Solution
    1st check Hard Disk Working  or Not
    2nd check Partition table
    3rd  check reinstall Mac Os
    and
    after any problem vist ;  [email protected]

  • Grey screen/ flashing question mark folder help!

    my macbook starts up into the grey screen (no logo or indicator) and will eventually go into the flashing folder with the question mark. After hours of scouring forums I have tried the following things:
    restart holding c with install disc in -> macbook spins disk, thinks, ejects disk
    restart holding option -> grey screen, this time with movable cursor, does not advance from there. i left it for about ten minutes- should i leave it longer?
    reset PMU as per Apple article -> no effect
    reset PRAM as per Apple article -> no effect
    i'm beginning to become resigned to the fact that it might be an HDD issue. i feel as though i should still be able to boot from disc. i could be wrong. just wondering if anyone has ANY other suggestions before going to Apple for repairs.

    If the computer is under warranty the cost is carried by Apple. If it isn't, here's what I'd do...then again, I'm a tech and have access to lots of equipment. First I'd remove the drive (easy to do. turn off the computer, remove the battery, remove the little gate, remove the drive. The instructions are in the little booklet that came with the computer) and put it into an enclosure, connect to another computer and run drive diagnostics. If the drive can be repaired I'd format it, clone from my backup, and return to the computer. If the drive is dead I'd buy a new drive, clone from my backup, and be back up and running. There's a third, remote possibility - that the problem is the logic board and not the drive. But it is remote.
    What I'm getting at here is that yes, you can do it yourself but...you probably don't have an enclosure for a 2.5" drive so you'll probably just have to assume the drive is toast and buy a new one - check out NewEgg or Macsales.com. Without the external drive enclosure you give up the chance of restoring the drive and recovering data. Then again, if you can't anyway you'll have wasted $$$ on an enclosure you didn't need.
    Instead of worrying about what you've heard, call the local store and get a quote on replacing the drive and installing a drive that you bring yourself. That'll give you a ballpark figure to work with and you can move forward from there.

  • MBP has gray screen with question mark folder on start up

    Hi Mac Experts,
    I have a MBP that won't start up. I get a gray screen with the question mark folder. Nothing else. I tried starting without the battery and also while holding the shift key but still get the same result. Any idea what happened and what I should try next? Thanks!

    Need a Vacation:
    Use the Leopard disk.
    Repair Disk
    Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
    Go to Installer menu (Panther and earlier) or Utilities menu (Tiger and later) and launch Disk Utility.
    Select your HDD (manufacturer ID) in the left panel.
    Select First Aid in the Main panel.
    (Check S.M.A.R.T Status of HDD at the bottom of right panel, and report if it says anything but Verified)
    Click Repair Disk on the bottom right.
    If DU reports disk does not need repairs quit DU and restart.
    If DU reports errors Repair again and again until DU reports disk is repaired.
    If DU reports errors it cannot repair you will need to use a utility like Tech Tool Pro or Disk Warrior

  • My macbook fell and since then a white screen with question mark appears

    hey guys!
    i really need to know what to do, my macbook fell while it was on. it froze so i restarted it, but the white screen comes in with the apple begining sound and everything but the screen stays blank for about two minutes and then a folde with a question mark appears. i tried putting in the cd that came with it, samething happened but after a while the appe sign appears and the computer started off my installation disc, so i try re installing everything, but when i get to the screen that asks to select a destination, there is nothing available.
    i realize that the best thing to do is to go to an apple store and then sort everything out, but i am in haiti where the nearest apple store is in miami, i really need your help and i'm desparate cuz i cannot do anything without my laptop... please send me your help as soon as possible.
    thanks in advance

    Your hard disk has been damaged. At this point, it will need to be replaced with a new one. You'll need to call AppleCare and they'll have you mail it in for repairs. I'm not sure what the usual turnaround time for that is internationally, but in the United States it's about a week. I'd tack on a few extra days to get the laptop to and from Haiti.
    Either way, your computer will need to be repaired and the data that was on your hard disk will be lost. (Unless you take the machine to a 3rd party repair shop that specializes in recovering data from damaged hard disks.)

  • File folder with question mark, file folder with question mark

    Battery died went to turn on computer with adapter plug...
    white screen with flashin file folder with a question mark???
    How do i fix this?

    That folder with the question mark icon means that the MacBook can't find the boot directory. That can either mean it can't find the hard drive or the Operating System data on the hard drive is somehow corrupted.
    Put your install DVD into the optical drive (CD/DVD drive) and reboot. Be sure to either use the disc that came with your Mac, or, if you installed a later Mac OS X version from disc, use the newer disc. As soon as you hear the boot chime, hold down the "c" key on your keyboard (or the Option Key until the Install Disk shows up) until the apple shows up. That will force your MacBook to boot from the install DVD in the optical drive.
    Or if you are running 10.7 Lion, boot from the recovery partition (Command +R on boot) and use Disk Utility to repair your OS 10.7 partition.
    When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it. When it comes up is your Hard Drive in the list on the left?
    If it is, then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've clicked on the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions. After repairing use Startup Disk from the same menu to choose your hard drive for restarting from your hard drive.
    If your hard drive isn’t recognized in Disk Utility then your hard drive is probably dead.

  • Grey boxes with question marks

    When I view some PDFs, a grey box with a red question mark inside appears. I cannot move, edit, or delete these boxes. I searched the web and most of the responses indicated that such boxes indicated corrupt images, but my documents do not have images. Mine appear at the start and end of text blocks. They do not appear in thumbnail view. I am running Acrobat Professional, version 8.1.
    What are these boxes and how can I get rid of them?
    Attached is a screen shot of what I am seeing.
    Robert

    A little more info to follow up the excellent diagnosis.
    When Acrobat opens a PDF and it finds annotations of an unknown type it shows these boxes. The way to get them to disappear (or change to something else) is to install a specific plug-in designed to show them.
    Older versions of Acrobat would just show nothing at all.
    Acrobat 5 would show nothing.
    Acrobat 7 would show the boxes.

  • White screen with question mark on iMac

    I have a white screen with a file folder icon and a question mark.  Anyone know what's wrong?  The iMac will not load.

    Besides checking out the possible solutions over in the "More Like This" thread over here----------------------->
    Check out KB Article: 
    http://support.apple.com/kb/PH11046 OS X Mountain Lion: If a flashing question mark appears

  • White Screen with Question Mark Flashing

    Hi
    All the sudden I have the white screen with the flashing question mark.  I have a macbook pro 2010.  I unscrewed the bottom of my Mac and wiggled a couple of wires around and it actually booted up and ran for a while.  Then it started to freeze on me.  I put in the Mac disk, and I went to the disk Utitlity and it says disk 2 Mac OS X Base System.  So it looks like it is reading the Hard Drive, but I don't know because I do not know that much about computers.  The thing is it will not let me erase or repair that drive.  Does anybody have any idea on what this is?  I used my computer around 1:30 in the afternoon and then came home to do homework around 5 and in a matter of 4 hours my computer does not work.  I am guessing that it is probably something serious and I will not be buying mac again.
    Any Help??
    Thanks,
    Matt   

    Hi
    All the sudden I have the white screen with the flashing question mark.  I have a macbook pro 2010.  I unscrewed the bottom of my Mac and wiggled a couple of wires around and it actually booted up and ran for a while.  Then it started to freeze on me.  I put in the Mac disk, and I went to the disk Utitlity and it says disk 2 Mac OS X Base System.  So it looks like it is reading the Hard Drive, but I don't know because I do not know that much about computers.  The thing is it will not let me erase or repair that drive.  Does anybody have any idea on what this is?  I used my computer around 1:30 in the afternoon and then came home to do homework around 5 and in a matter of 4 hours my computer does not work.  I am guessing that it is probably something serious and I will not be buying mac again.
    Any Help??
    Thanks,
    Matt   

Maybe you are looking for

  • XSLT for ABAP to XML: how can I get a variable in a literal field

    Hi, I have the requirement to provide an xml format (for Intrastat reporting) which contains some dynamic data within "". Example (I'll put the variables between && for clarity): <?xml version='1.0' encoding='UTF-8'?>      <DeclarationReport xmlns="h

  • .swf files not viewing properly

    I am trying to place a .swf file that was made on a PC into my keynote document. All I am getting is a tall black column with type in it. This file works fine in power point but I would like to use Keynote for this presentation. Can anyone help?

  • ComboBox in a Matrix

    Hi, How do I build a Combo box in a matrix? (C#, (or VB)) I have a empty matrix which the user key in data; so after row 1, row 2 has to be created with combo box, etc. Thank you, Rune

  • Changing Freight Conditions on PO

    The issue that I am having is that we have created a PO with a freight condition. Instead of the price for the condition being for one 1 ton it was for 1 pound. There was a goods receipt already done for this line item. I have tried to back out the r

  • Getting playlists to sync and remember playback position

    Hi -- Is it possible to create a playlist where all the items in that playlist have the "Remember playback position" ticked, such that both ipod and itunes sync up the playlist position when connected? I've tried this, and for some reason even with "