Grey start up screen with clock countdown but no start up?

my less than a week old 2.2GHZ SR MBP seemed to be perfect but i keep getting the following problem.
the computer hangs at the grey screen that has the apple logo and refuses to start up properly, the counter thingy spins but the machine refuses to start.
i removed the battery and held down the power key for 5 secs and then it seems to start okay. this problem has happened a few times, should i be concerned?
The last time it did it i was using firefox browser and i had the beachball, could not close down so held power button till it shutdown and then it refused to restart.
I have also just reset the pvram by holding down the command, option, p and r keys till i heard the second chime.
Don,t know if that has solved the problem yet as it is too early to say.
Advice appreciated.
Simon

You have already performed some of the normal troubleshooting procedures.
Have you opened Disk Utilities from the utilities folder in the application folder and run the the Disk Repair Verification? You can verify without starting from a dvd or external disk. If Disk Repair says that the volume needs to be repaired; open your install dvd and start from it to run Disk Repair. That will check for any software problems.
To locate any possible hardware problem, insert the same install disc and press D as you restart the computer. That will bring you to the hardware test and then
you allow that to run and check for hardware problems.
If you find no problems and the hangup does not recur, just figure it might have been an anomaly caused by one of those programs that you were installing. The problem may have already been resolved.

Similar Messages

On start up I get grey screen with wheel turning but it goes no further

On start up I get grey screen with wheel turning but it goes no further

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
     a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, boot from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Accidentally deleted startupitems from library/startupitems on macbook now the computer wont startup and i get the grey startup loading screen with the apple symbol and a loading bar but wont load then turns off.

hi, please help.
Accidentally deleted startupitems from library/startupitems on macbook now the computer wont startup and i get the grey startup loading screen with the apple symbol and a loading bar but wont load then turns off.
i saved these files to a folder on the destop and then turned the computer off. oops!!! now computer wont start up
How do i put the startupitems back to this folder or beter yet get into the computer to fix this.
Please please help!!!

Reinstall OS X, either from disc or a recovery partition. You don't mention which version of OS X you're running so I don't know which it will be.

Computer wont go past grey apple startup screen with spinning gear help!!!!

Hey everyone Im hoping someone can help. I just did a software update download from Apple. It came back and said that not all of the items were installed and the computer needed to restart. I did the restart. Now it wont go past the grey apple screen with the spinning gear.
Any ideas anyone?
THanks

Hi Ghost516, and a warm welcome to the forums!
You have corruption on your Hard Drive, likely before the updates even.
"Try Disk Utility
1. Insert the Mac OS X Tiger Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then Safe Boot , (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it finishes.
The usual reason why updates fail or mess things up, or things don't load/run, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates again, or even do an A&I if you have enough free disk space.
The combo update for PowerPC-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateppc.html
The combo update for Intel-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateintel.html
Repair Permissions before & after re-install, then reboot again each time.
If all the above do not resolve the problem, then it's time for a relatively painless Archive & Install, which gives you a new/old OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space, and don't have any Disk Directory problems...
http://docs.info.apple.com/article.html?artnum=107120
Be sure to use Preserve Users & Settings.
I only use Software Update to see what is needed, then get them for real via...
http://www.apple.com/support/downloads/
That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.
If it appears to be time for An Archive & Install, which gives you a new OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space...
http://docs.info.apple.com/article.html?artnum=107120
Be sure to use Preserve Users & Settings.
If none ofthis works report back.

Stuck on grey boot-up screen with Apple logo & spinning icon for 12 hours

I awoke to find my computer displaying the 'Restart your computer' screen, which I did by holding down the power button. Upon restarting, I got the grey loading screen with the apple icon and the spinning wheel. It stayed that way for hours without proceding. Have tried removing the battery, removing the charger and restarting. Have tried doing a forced disk-boot by holding down 'c' and restarting with the OS X disc 1 in the drive, but all I got was a beep and then the same screen again.
I'm starting to get a little nervous here as nothing is working, and there don't seem to be any others with the same problem I'm having!

Have you changed your Ram or done anything else
lately - here's a reference to your 'beep'...
http://docs.info.apple.com/article.html?artnum=58442
I'd suggest trying an SMC reset...
http://docs.info.apple.com/article.html?artnum=303319
followed by a Pram reset...
http://docs.info.apple.com/article.html?artnum=2238
Hopefully some of these resets will correct the
problem. Have you 'jarred' you book and maybe
loosened the ram??
I unfortunately have tried all of those and haven't had any luck.
Pardone my ignorance, but if I have dislodged the RAM, how would I know? And, potentially more significantly, how do I fix it?
Thanks for the help thus far, though.

Grey and Blue Screens with Spinning Pinwheel

Mid 2009 Macbook Pro 13 inch with Mac OSX Snow Leopard installed. 2.26 GHZ 4 GB 160 GB Version 10.6.3
I got this dead Macbppk Pro from my daughter . I put in a new battery and re-installed Mac OSX Snow Leopard from the licesned disc she bought so I could get rid of all her files and have free space and to make the Macbook now mine with my passwords etc. I got free support from Apple on how to install the disc and overwrite everything that was on it.
Until now ... I get a Grey Screen with the Spinning Pinwheel for endless time.
So the I tired the Hold Alt/ Option + Command + holding the P and R buttons while starting it up and got a Blue Screen with the spinning Pinwheel.
Any Help on what to try next ?
I only use it about once a month because I have a desktop. Does using it only once a month harm anything ? Should I be doing anything to not have this problem with it ?
Or do I have to re-install the disc again and if so .... what would be the procedure to do so ( I forget )
Thanks Eric

Hi Eric,
Thanks for visiting Apple Support Communities.
If your MacBook Pro is only starting up to a blue screen with spinning pinwheel, reinstalling OS X may be necessary. I would recommend going through all of these steps first:
Restart the computer in safe mode. If the computer successfully starts up in safe mode, choose Apple menu > Restart to see whether the computer will restart normally.
Starting up in safe mode
If you see the login window prompting you for a user name and password, but starting up doesn't progress, you may have incompatible login items.
Eliminating incompatible login items
Repair your startup disk or disk permissions by starting up from your Mac OS X installation disc and using Disk Utility.
Repairing a disk
Back up your disk and then reinstall Mac OS X by starting up your computer with your Mac OS X installation disc.
Reinstalling Mac OS X
From:
Mac OS X 10.6: If you see a blue screen at startup
Best Regards,
Jeremy

IMac has gray screen with spinning wheel, but cannot login

After power failure last night, iMac has gray screen with spinning wheel when turned on, but does not go to login screen.

Having the same problem myself. iMac locked up and I had to hold the power button to turn it off. Ended up with the apple logo screen and spinning wheel. I tried the disk repair and got the same message as yourself, in that it couldn't repair it.
I linked up an external hard drive and installed OSX on it and booted from it. I was able to recover some files, but most I couldn't. I'm currently giving it a one pass erase in the hope (long shot) that a complete pass through the hard drive will show up any faults. Has anyone had this problem and been able to continue using the same hard drive? I really don't relish the thought of having to send it off to be replaced :-/
Assuming that the erase goes well I plan to put OSX back onto it and then run disk utility from directly on the drive and see if any faults show up. I'm kicking myself for not taking advantage of TimeMachine, but we live and learn.

Got the white screen with flashing ? But no startup disk to be found

Need some help as following all instructions from everyone I cannot reinstall OS X mountain lion (I was using Mavericks but Mountain Lion is all that is coming up - issue is when asked to select disk where I want to install nothing come up??

A flashing question mark appears when you start your Mac
Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by one or more of these:
Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
Boot drive's directory has been corrupted - Repair with Disk Utility.
Critical system files are damaged or deleted - Reinstall OS X.
The disk drive is physically non-functional - Replace the hard drive.
Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

All my pictures have disappeared all that i see is gray screen with dashed boarders but picture titles are there

I am running on Lion and iphoto. My 13000 pictures seem to have disappeared except for a dashed boarder where each picture should be and the title of the photo. I use timemachine for backup but when I try to restore I get an error message saying I don't have privileges for iphoto. What should I do?

The ! turns up when iPhoto loses the connection between the thumbnail in the iPhoto Window and the file it represents.
Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Rebuild iPhoto Library Database from automatic backup.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. .
Regards
TD

My macbook pro 2011 shows grey screen with apple logo and want start

i was just using my macbook pro and it freezed for a while not responding and i turned it off by pressing the power button. afterwards, i turn it on and it shows a grey screen with apple logo but want start pls somebody help me because am having "my life" on the machine

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

G5 freezes at startup, get grey screen with logo, but no spinning gear

As subject says, I get the Grey Startup screen with aple logo, but no spining gear.
do i need a new install of OS X? Or ???

Hi wampaskitty, and a warm welcome to the forums!
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
If that doesn't work, Boot off your original G5 Install Disk while holding down Option/alt key to select AHT, then run the extended Apple Hardware Test.

My powerbook won't load past the grey apple logo screen

I had been away on business for a few weeks and yesterday I decided to run the latest updates for my powerbook. In the middle of it the computer froze for what I think is the first time since I bought it 2 years ago. I ended up having to shut the computer down with the power button. When I turned it on it wouldn't and still won't advance past the grey apple logo screen with the progress indicator. It just sits there for hours on end if I let it.
So far I've tried the following, all to no avail.
Booting in safe mode I get the same result.
Zapping the Ram
Resetting the PMU
Reinstalling OS X, during which the computer either randomly shuts down or goes to sleep and then shuts down and requires me to reset the PMU in order to start again.
Running the hardware diagnosis. I did this once and it froze during the logic board test, 1 minute 6 seconds in to it.
Anyone have any ideas that don't involve spending 900 dollars on a logic board? Thanks a lot for any help.

joeuu, thanks for the reply. i checked the airport and the ram and both seem to be seated properly.
i ran the quick hardware diagnosis and it came back showing everything was fine.
when i ran the extended one i got more progress than i did the first time. it got to the RAM diagnosis (about 6:45 seconds in) and then froze - i let it sit like this for an hour and a half to make sure it was actually frozen.
i also tried to run the disc utility from the installation disc and it just sits there with the progress wheel spinning, but nothing else is going on.

Black Screen with cursor that doesn't move! Help!

Hi, a few months ago my family encountered a problem when we started up our laptop and it prompted us that our laptop failed to start. As usual, I just pressed "Launch Startup Repair". That lead us to a black screen with nothing else but a cursor
that DOES NOT move.
We put the laptop aside as none of us knew the resolution and somebody we knew might have been able to fix it, but unfortunately to this day he hasn't been over to help us out. Our laptop is still in the same state and we're very eager to get it working
without having to spend lots of money at a computer specialist.
Our specifications are as following:
Toshiba Satellite A660
Intel Core i5 CPU M 450
2.40GHz
4096 MB Memory
I am unable to get other specifications such as Video Card and Graphics Drivers as I cannot access the desktop.
Any fixes? We are very desperate to get this computer working.
< Disclaimer > We do have another PC in the household if that is necessary for the fix. Thank you.

Hello PamelaMay,
What is your current situation?
Have you tried the solution as MVP Robear Dyer mentioned?
Best regards，
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

There isn't Org. Search in free search of PERNR on PNP Screen with report

Hi experts,
I create a standard PNP screen with HR report, but i find there isn't org. structure search in free search for PERNR .
Should I do configure anywhere to use the org. struture search of PERNR ?
Thanks a lots.
Yoga.

Hi,
do you use a reportclass e.g. X__X2201 ?
Regards
Bernd

I am experiencing some major problems with my MacBook Pro. I have had some issues with it turning on/off at random times, but today, when starting, I get the grey start-up screen and a recovery bar. After filling in approx 1/4 of the way, the machine dies

I am experiencing some major problems with my MacBook Pro. I have had some issues with it turning on/off at random times, but today, when starting, I get the grey start-up screen and a recovery bar. After filling in approx 1/4 of the way, the machine dies. After starting it in recovery mode, it will not allow me to download OS X Mavericks- it says the disk is locked. Any ideas? I do not have a back-up and do not want to erase everything before I have explored my options. Help?

try forcing internet recover, hold 3 keys - command, option, r - you should see a spinning globe
most people will tell you to do both pram and smc resets (google) and if you still have issues, either clean install (easy) or troubleshoot (hard)

Grey start up screen with clock countdown but no start up?

Similar Messages

Maybe you are looking for