GRUB Install Fails

I'm trying to install Arch onto a laptop with a RAID 1 setup.  I followed the fake raid guide on the wiki and I'm stumped at the installing GRUB portion.
I'm able to chroot into the new environment and when I attempt to install GRUB on /dev/mapper/raidSet using "device (hd0) /dev/mapper/raidSet
I receive Error 15: File not found.
What file is it looking for that it cannot find?

Chances are that /dev/ isn't populated with the raid devices when you chroot into it. That's only a guess and I'm sorry I don't know what to do to fix it since my experience with RAID is only with ZFS.

Similar Messages

  • [solved] grub install fails /boot/grub is not readable

    virtualbox install
    single partition install (well, I have two partitions, #2 is / and #1 is the BIOS partition as defined in the install docs)
    when I get to the stage of installing grub, I use :
    grub-install --target=i386-pc --recheck /dev/sda
    which fails with
    Path '/boot/grub' is not readable by GRUB on boot. Installation is impossible. Aborting"
    it is ext4
    fstab looks correct. It shows one entry for
    /dev/sda1 / ext4
    I am not using UUID although when I did the result was the same.
    when run with debug, the problem is
    /usr/bin/grub-probe -t fs /boot/grub
    results in path no readable.
    when I run the grub-probe inside the chroot, I get error: unknown filesystem
    haven't had this before. This is the first time I've tried a GPT install.
    It is virtualbox 4.2.18
    I
    Last edited by timrichardson (2013-10-15 10:10:50)

    Ah, my mistake was an incorrect partition table back when I partitioned the disk. I did not make a partition table for GPT partitions.

  • Grub-install fails to install core.img to boot partition

    I am trying to reinstall Arch onto a Dell Precision T3600 workstation, where it used to work fine, but I am stuck at the booloader step.
    Details:
    1. I have only one disk, partioned with gpt.
    2. I am using Grub with Bios
    3. As per installation instructions (preliminary requirements, BIOS systems), I created a 1007KiB boot partition at the beginning of the disk, of type ef02.
        The partition (which is umber 5 in my partition table) goes from sector 34 to sector 2047
    4. I mounted the root partition to /mnt, arch-chroot'd into it, and ran
    # grub-install --target=i386-pc --recheck --debug /dev/sdx
    # grub-mkconfig -o /boot/grub/grub.cfg
    5. I generated the /boot/grub.cfg file with the recommended
    # grub-mkconfig -o /boot/grub/grub.cfg
    Results:
    when I try to boot, grub starts, but it cannot find anything to boot from and drops me into its shell.
    Furthermore (this may be unrelated), when I take a look at the dis again (after rebooting from the install disk), I see that the gpt partition table is corrupted. Exact message  from gdisk is:
    Caution: invalid backup GPT header, but valid main header: regenerating backup header from main header:
    Partition table scan:
    MBR: protective
    BSD: not present
    APM: not present
    GPT: damaged
    Can anyone tell me where I am going wrong? The Installation manual is not very explicit on how to deal with the (very small) boot partition. Is grub-install supposed to create the core.img file even when the partition is not mounted? Or should it be mounted. It certainly cannot contain eveyrthing that goes into /boot (which is over 100Mb).
    Thanks for the help

    Head_on_a_Stick wrote:
    Your partition table is corrupted; you could clear it using:
    # dd if=/dev/zero of=/dev/sd<x> bs=512 count=1; sync
    Then use gdisk to recreate your partition table and re-install.
    Alternatively, you could ask gdisk to re-create the backup GPT header from the main header: start up the program & press "r" followed by "d".
    I had already fixed the partition table exactly as you suggested---sorry for not having been clear. It still does not boot. 
    Head_on_a_Stick wrote:
    Your partition table is corrupted; you could clear it using:
    If it still will not boot, post your /boot/grub/grub.cfg along with the output of:
    # gdisk -l /dev/sd<x>
    lsblk -f
    Here they are:
    /boot/grub.cfg:
    # DO NOT EDIT THIS FILE
    # It is automatically generated by grub-mkconfig using templates
    # from /etc/grub.d and settings from /etc/default/grub
    ### BEGIN /etc/grub.d/00_header ###
    insmod part_gpt
    insmod part_msdos
    if [ -s $prefix/grubenv ]; then
    load_env
    fi
    if [ "${next_entry}" ] ; then
    set default="${next_entry}"
    set next_entry=
    save_env next_entry
    set boot_once=true
    else
    set default="0"
    fi
    if [ x"${feature_menuentry_id}" = xy ]; then
    menuentry_id_option="--id"
    else
    menuentry_id_option=""
    fi
    export menuentry_id_option
    if [ "${prev_saved_entry}" ]; then
    set saved_entry="${prev_saved_entry}"
    save_env saved_entry
    set prev_saved_entry=
    save_env prev_saved_entry
    set boot_once=true
    fi
    function savedefault {
    if [ -z "${boot_once}" ]; then
    saved_entry="${chosen}"
    save_env saved_entry
    fi
    function load_video {
    if [ x$feature_all_video_module = xy ]; then
    insmod all_video
    else
    insmod efi_gop
    insmod efi_uga
    insmod ieee1275_fb
    insmod vbe
    insmod vga
    insmod video_bochs
    insmod video_cirrus
    fi
    if [ x$feature_default_font_path = xy ] ; then
    font=unicode
    else
    insmod part_gpt
    insmod ext2
    set root='hd0,gpt3'
    if [ x$feature_platform_search_hint = xy ]; then
    search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt3 --hint-efi=hd0,gpt3 --hint-baremetal=ahci0,gpt3 74c69286-1775-44de-90c8-3834585da6b6
    else
    search --no-floppy --fs-uuid --set=root 74c69286-1775-44de-90c8-3834585da6b6
    fi
    font="/usr/share/grub/unicode.pf2"
    fi
    if loadfont $font ; then
    set gfxmode=auto
    load_video
    insmod gfxterm
    set locale_dir=$prefix/locale
    set lang=en_US
    insmod gettext
    fi
    terminal_input console
    terminal_output gfxterm
    if [ x$feature_timeout_style = xy ] ; then
    set timeout_style=menu
    set timeout=5
    # Fallback normal timeout code in case the timeout_style feature is
    # unavailable.
    else
    set timeout=5
    fi
    ### END /etc/grub.d/00_header ###
    ### BEGIN /etc/grub.d/10_linux ###
    ### END /etc/grub.d/10_linux ###
    ### BEGIN /etc/grub.d/20_linux_xen ###
    ### END /etc/grub.d/20_linux_xen ###
    ### BEGIN /etc/grub.d/30_os-prober ###
    ### END /etc/grub.d/30_os-prober ###
    ### BEGIN /etc/grub.d/40_custom ###
    # This file provides an easy way to add custom menu entries. Simply type the
    # menu entries you want to add after this comment. Be careful not to change
    # the 'exec tail' line above.
    ### END /etc/grub.d/40_custom ###
    ### BEGIN /etc/grub.d/41_custom ###
    if [ -f ${config_directory}/custom.cfg ]; then
    source ${config_directory}/custom.cfg
    elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
    source $prefix/custom.cfg;
    fi
    ### END /etc/grub.d/41_custom ###
    ### BEGIN /etc/grub.d/60_memtest86+ ###
    ### END /etc/grub.d/60_memtest86+ ###
    lsblk -f (sda1 is the swap partition, sda5 is the boot partition):
    NAME FSTYPE LABEL UUID MOUNTPOINT
    sda
    sda1
    sda3 /
    sda4 /home
    sda5
    sr0
    loop0
    loop1
    arch_root-image /etc/resolv.conf
    loop2
    arch_root-image /etc/resolv.conf
    Finally, here is the partition table from gdisk -l
    GPT fdisk (gdisk) version 0.8.10
    Partition table scan:
    MBR: protective
    BSD: not present
    APM: not present
    GPT: present
    Found valid GPT with protective MBR; using GPT.
    Disk /dev/sda: 1953525168 sectors, 931.5 GiB
    Logical sector size: 512 bytes
    Disk identifier (GUID): 8B675D08-1A4A-44D3-ADC3-A7763E331455
    Partition table holds up to 128 entries
    First usable sector is 34, last usable sector is 1953525134
    Partitions will be aligned on 8-sector boundaries
    Total free space is 0 sectors (0 bytes)
    Number Start (sector) End (sector) Size Code Name
    1 2048 67112959 32.0 GiB 8200 Linux swap
    3 67112960 276828159 100.0 GiB 8300 Linux filesystem
    4 276828160 1953525134 799.5 GiB 8300 Linux filesystem
    5 34 2047 1007.0 KiB EF02 BIOS boot partition

  • [SOLVED]Grub-Install can't Find Kernel and/or initrd, mkinitcpio Fails

    Hi all,
    I have recently installed Arch on my new build (with UEFI firmware). I successfully set up xorg, alsa/pulseaudio, xfce, etc... things were looking pretty good. Then, I tried to blacklist the pcspkr in order to silence the annoying beep every time I selected "Log Out" inside xfce. I executed
    mkinitcpio -p linux
    and was presented with the following errors:
    ==> Building image from preset: 'default'
    -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
    ==> ERROR: specified kernel image does not exist: `/boot/vmlinuz-linux'
    ==> Building image from preset: 'fallback'
    -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
    ==> ERROR: specified kernel image does not exist: `/boot/vmlinuz-linux`
    There were no such files anywhere on /boot. I tried doing
    find / -name vmlinuz-linux
    and nothing was found. I wasn't quite sure why that was happening, but I tried uninstalling/reinstall grub (grub-common and grub2-efi-x86_64). I installed grub to /boot using
    grub-install --directory=/usr/lib/grub/x86_64-efi --target=x86_64-efi --efi-directory=/boot --bootloader-id="Arch Linux" --boot-directory=/boot --recheck --debug
    and then generated /boot/grub/grub.cfg. I tried rebuilding the initramfs again but got the same error. I was tired and frustrated so I removed the old grub efi entry with
    efibootmgr -b 0 -B
    and then went to sleep.
    I didn't have the chance to turn the computer back on until tonight... I was then presented with a grub2 shell. Since I didn't know where the kernel/initrd were located I tried
    set root=(hd1,gpt1)
    chainloader +1
    but grub told me
    error: invalid EFI file path
    So that's about it. It appears that grub-mkconfig is having trouble locating the kernel/initrd so it doesn't make any entries, dropping me right into a shell. I've tried booting up with my installation USB and chrooting in and reinstalling grub again but nothing seems to work. So what I'd like to try to do is just boot up into my system and then modify add the grub boot entries entries I want... but I just can't figure out what's causing all these issues.
    Sorry if I mess up any terminology... still learning the ropes here. Thanks for any input.
    Last edited by cogeary (2012-09-17 05:35:51)

    DSpider wrote:
    ==> ERROR: specified kernel image does not exist: `/boot/vmlinuz-linux'
    Probably because you have a separate boot partition (not just the 512 MB "UEFISYS" FAT32 partition), which you forgot to mount (in fstab).
    Post your /etc/fstab.
    Thank you for your reply!
    However, I do not have a separate boot partition apart from the "UEFISYS" partition. Here is my fstab:
    # UUID=3ec307aa-0ead-4d33-b292-42bbe783d6ee
    /dev/sda2 / ext4 rw,relatime,data=ordered 0 1
    # UUID=B192-6C57
    /dev/sda1 /boot vfat rw,relatime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro 0 2
    When I first looked at the fstab I saw that both of the entries repeated themselves. This was because I had even tried reformatting /boot so I had to generate a new fstab, but for some reason I used ">> /mnt/etc/fstab" rather than "> ..."
    So I executed
    genfstab /mnt > /mnt/etc/fstab
    and reinstalled grub, but still no difference... mkinitcpio fails and I reboot to a grub shell.
    Last edited by cogeary (2012-09-16 18:15:51)

  • [SOLVED] grub-install command failing for UEFI

    I downloaded the 8/2013 iso and burned it with dd. I have an ASUS Rampage IV Extreme motherboard. I was booted into efi mode on both the ISO and in the chroot (the /sys/firmware/efi directory did exist).
    I followed the instructions in the Beginner's Guide, but with a 512 MB EFI partition as sda1, 50 GB root as sda2, the rest of my 256 GB SSD as /home, and a 100 GB space on my HDD as /tmp. Everything was ext4 and the EFI partition was a fat32. The EFI partition was mounted on /boot of the new install, as the beginner's guide stated it should be
    Everything worked until I get to the part of installing GRUB. Before installing, I again confirmed that /sys/firmware/efi existed. When booting, on the motherboard boot selection screen, it showed 2 options for my USB, one with the name of my drive and another with [UEFI] in front of the drive name. I selected the UEFI option, so I was booted into UEFI mode, and the USB's bootloader also gave options to boot into a UEFI shell instead of the standard Arch ISO bootloader I get on MBR computers (though I did not try those EFI shell options). I looked into te /sys/firmware/efi/efivars directory and it had 2 items in it
    Going back to the chroot's / directory, I did the first command in the guide for installing grub (after installing grub and efibootmgr with pacman).
    umount /sys/firmware/efi/efivarsk
    This gave the error that the directory was not mounted
    modprobe -r efivars and modprobe efivars worked correctly (or at least they didn't output any errors).
    When I got to
    grub-install --efi-directory=/boot --bootloader-id=arch_grub --recheck
    it gave this error:
    Fatal: Couldn't open either sysfs or procfs directories for accessing EFI variables.
    I searched around on the interwebs and for every other person this problem was occuring because they were booted into BIOS mode instead of UEFI mode, and booting the USB into UEFI mode fixed the problem for them. However, the /sys/firmware/efi directory exists and I made sure to boot into EFI mode in the BIOS.
    Are there any other reasons that this could be happening?
    Also, is there really any advantage to GPT/EFI booting over GPT/BIOS booting other than a 1-2 second shorter boot time?
    Last edited by subraizada3 (2013-08-23 21:10:37)

    You burnt it to CD?DVD, right? Not dd? Because that won't create an EFI bootable USB key, for example.
    modprobe efivars never gives errors (that I've seen). The question is whether the directories are populated. It isn't enough for /sys/firmware/efi to exist. /sys/firmware/efi/vars/ should be full of a *lot* of stuff. In fact /sys/firmware/efi/efivars/ should have lots of stuff before you umount it.
    Did you modprobe before arch-chroot? That's essential if the installed kernel is different from the one on the installer (which is very likely).
    I think you are confused. There's no such thing as GPT/MBR booting.
    GPT and MBR are 2 ways of partitioning disks. GPT has various advantages explained on the wiki page.
    EFI and BIOS are 2 ways of booting.
    In my personal opinion, if BIOS booting works for you, I'd stick with BIOS. EFI is buggy - why be a guinea pig if you can help it?
    Also in my personal opinion, if you can only use GPT in EFI mode, it is worth the hassle to use EFI to reap the benefits of GPT.
    At least, those are the decisions I made. Nothing will convince my laptop to boot BIOS mode with a GPT disk. MBR+BIOS is fine but GPT+BIOS is a non-starter. So I use GPT+EFI.  On machines that don't care, I prefer BIOS+GPT.
    If you are dual booting Windows, I believe BIOS+GPT may not be an option but I'm not certain of this.
    Your kilometres may vary.
    By the way, you almost certainly do not want a partition for /tmp unless you are extraordinarily short of RAM and even then...

  • Component SMS_Contol_manager and SMS_Notification_server install failed on SCCM2012

    we have try to uninstall client and remove the ccm namespace from wmi, and reisntall MP, no luck
    below log from mpmsi.log.lasterror
    === Verbose logging started: 8/27/2014  20:50:23  Build type: SHIP UNICODE 5.00.9600.00  Calling process: H:\Program Files\Microsoft Configuration Manager\bin\x64\rolesetup.exe ===
    MSI (c) (9C:58) [20:50:23:592]: Resetting cached policy values
    MSI (c) (9C:58) [20:50:23:592]: Machine policy value 'Debug' is 0
    MSI (c) (9C:58) [20:50:23:592]: ******* RunEngine:
               ******* Product: h:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi
               ******* Action:
               ******* CommandLine: **********
    MSI (c) (9C:58) [20:50:23:592]: Client-side and UI is none or basic: Running entire install on the server.
    MSI (c) (9C:58) [20:50:23:592]: Grabbed execution mutex.
    MSI (c) (9C:58) [20:50:23:594]: Cloaking enabled.
    MSI (c) (9C:58) [20:50:23:594]: Attempting to enable all disabled privileges before calling Install on Server
    MSI (c) (9C:58) [20:50:23:594]: Incrementing counter to disable shutdown. Counter after increment: 0
    MSI (s) (24:FC) [20:50:23:598]: Running installation inside multi-package transaction h:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi
    MSI (s) (24:FC) [20:50:23:598]: Grabbed execution mutex.
    MSI (s) (24:48) [20:50:23:599]: Resetting cached policy values
    MSI (s) (24:48) [20:50:23:599]: Machine policy value 'Debug' is 0
    MSI (s) (24:48) [20:50:23:599]: ******* RunEngine:
               ******* Product: h:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi
               ******* Action:
               ******* CommandLine: **********
    MSI (s) (24:48) [20:50:23:599]: Machine policy value 'DisableUserInstalls' is 0
    MSI (s) (24:48) [20:50:23:603]: Note: 1: 2203 2: C:\Windows\Installer\inprogressinstallinfo.ipi 3: -2147287038
    MSI (s) (24:48) [20:50:23:605]: SRSetRestorePoint skipped for this transaction.
    MSI (s) (24:48) [20:50:23:606]: Note: 1: 1402 2: HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer 3: 2
    MSI (s) (24:48) [20:50:23:607]: File will have security applied from OpCode.
    MSI (s) (24:48) [20:50:23:619]: SOFTWARE RESTRICTION POLICY: Verifying package --> 'h:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi' against software restriction policy
    MSI (s) (24:48) [20:50:23:619]: SOFTWARE RESTRICTION POLICY: h:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi has a digital signature
    MSI (s) (24:48) [20:50:23:619]: SOFTWARE RESTRICTION POLICY: h:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi is permitted to run because the user token authorizes execution (system or service token).
    MSI (s) (24:48) [20:50:23:619]: MSCOREE not loaded loading copy from system32
    MSI (s) (24:48) [20:50:23:621]: End dialog not enabled
    MSI (s) (24:48) [20:50:23:621]: Original package ==> h:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi
    MSI (s) (24:48) [20:50:23:621]: Package we're running from ==> C:\Windows\Installer\6257f6f.msi
    MSI (s) (24:48) [20:50:23:624]: APPCOMPAT: Compatibility mode property overrides found.
    MSI (s) (24:48) [20:50:23:624]: APPCOMPAT: looking for appcompat database entry with ProductCode '{6CED3AB0-05AF-4C81-8DBE-A62661C26F40}'.
    MSI (s) (24:48) [20:50:23:624]: APPCOMPAT: no matching ProductCode found in database.
    MSI (s) (24:48) [20:50:23:626]: Machine policy value 'TransformsSecure' is 1
    MSI (s) (24:48) [20:50:23:627]: Note: 1: 2262 2: MsiFileHash 3: -2147287038
    MSI (s) (24:48) [20:50:23:627]: Machine policy value 'DisablePatch' is 0
    MSI (s) (24:48) [20:50:23:627]: Machine policy value 'AllowLockdownPatch' is 0
    MSI (s) (24:48) [20:50:23:627]: Machine policy value 'DisableLUAPatching' is 0
    MSI (s) (24:48) [20:50:23:627]: Machine policy value 'DisableFlyWeightPatching' is 0
    MSI (s) (24:48) [20:50:23:627]: APPCOMPAT: looking for appcompat database entry with ProductCode '{6CED3AB0-05AF-4C81-8DBE-A62661C26F40}'.
    MSI (s) (24:48) [20:50:23:627]: APPCOMPAT: no matching ProductCode found in database.
    MSI (s) (24:48) [20:50:23:627]: Transforms are not secure.
    MSI (s) (24:48) [20:50:23:628]: PROPERTY CHANGE: Adding MsiLogFileLocation property. Its value is 'h:\Program Files\Microsoft Configuration Manager\logs\mpMSI.log'.
    MSI (s) (24:48) [20:50:23:628]: Command Line: CCMINSTALLDIR=h:\Program Files\SMS_CCM CCMSERVERDATAROOT=h:\Program Files\Microsoft Configuration Manager USESMSPORTS=TRUE SMSPORTS=80 USESMSSSLPORTS=TRUE SMSSSLPORTS=443 USESMSSSL=TRUE SMSSSLSTATE=0 CCMENABLELOGGING=TRUE
    CCMLOGLEVEL=1 CCMLOGMAXSIZE=1000000 CCMLOGMAXHISTORY=1 CURRENTDIRECTORY=H:\Program Files\Microsoft Configuration Manager\bin\x64 CLIENTUILEVEL=3 MSICLIENTUSESEXTERNALUI=1 CLIENTPROCESSID=6556
    MSI (s) (24:48) [20:50:23:628]: Product Code passed to Engine.Initialize:           ''
    MSI (s) (24:48) [20:50:23:628]: Product Code from property table before transforms: '{6CED3AB0-05AF-4C81-8DBE-A62661C26F40}'
    MSI (s) (24:48) [20:50:23:628]: Product Code from property table after transforms:  '{6CED3AB0-05AF-4C81-8DBE-A62661C26F40}'
    MSI (s) (24:48) [20:50:23:628]: Product not registered: beginning first-time install
    MSI (s) (24:48) [20:50:23:630]: Machine policy value 'DisableMsi' is 1
    MSI (s) (24:48) [20:50:23:630]: Product {6CED3AB0-05AF-4C81-8DBE-A62661C26F40} is not managed.
    MSI (s) (24:48) [20:50:23:630]: MSI_LUA: Credential prompt not required, user is an admin
    MSI (s) (24:48) [20:50:23:630]: PROPERTY CHANGE: Adding ProductState property. Its value is '-1'.
    MSI (s) (24:48) [20:50:23:630]: Entering CMsiConfigurationManager::SetLastUsedSource.
    MSI (s) (24:48) [20:50:23:630]: User policy value 'SearchOrder' is 'nmu'
    MSI (s) (24:48) [20:50:23:630]: Adding new sources is allowed.
    MSI (s) (24:48) [20:50:23:630]: PROPERTY CHANGE: Adding PackagecodeChanging property. Its value is '1'.
    MSI (s) (24:48) [20:50:23:630]: Package name extracted from package path: 'mp.msi'
    MSI (s) (24:48) [20:50:23:630]: Package to be registered: 'mp.msi'
    MSI (s) (24:48) [20:50:23:631]: Note: 1: 2262 2: AdminProperties 3: -2147287038
    MSI (s) (24:48) [20:50:23:631]: Machine policy value 'AlwaysInstallElevated' is 0
    MSI (s) (24:48) [20:50:23:631]: User policy value 'AlwaysInstallElevated' is 0
    MSI (s) (24:48) [20:50:23:631]: Product installation will be elevated because user is admin and product is being installed per-machine.
    MSI (s) (24:48) [20:50:23:631]: Running product '{6CED3AB0-05AF-4C81-8DBE-A62661C26F40}' with elevated privileges: Product is assigned.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding CCMINSTALLDIR property. Its value is 'h:\Program Files\SMS_CCM'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding CCMSERVERDATAROOT property. Its value is 'h:\Program Files\Microsoft Configuration Manager'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding USESMSPORTS property. Its value is 'TRUE'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding SMSPORTS property. Its value is '80'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding USESMSSSLPORTS property. Its value is 'TRUE'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding SMSSSLPORTS property. Its value is '443'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding USESMSSSL property. Its value is 'TRUE'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding SMSSSLSTATE property. Its value is '0'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding CCMENABLELOGGING property. Its value is 'TRUE'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding CCMLOGLEVEL property. Its value is '1'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding CCMLOGMAXSIZE property. Its value is '1000000'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding CCMLOGMAXHISTORY property. Its value is '1'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding CURRENTDIRECTORY property. Its value is 'H:\Program Files\Microsoft Configuration Manager\bin\x64'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding CLIENTUILEVEL property. Its value is '3'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding MSICLIENTUSESEXTERNALUI property. Its value is '1'.
    MSI (s) (24:48) [20:50:23:631]: PROPERTY CHANGE: Adding CLIENTPROCESSID property. Its value is '6556'.
    MSI (s) (24:48) [20:50:23:631]: Machine policy value 'DisableAutomaticApplicationShutdown' is 0
    MSI (s) (24:48) [20:50:23:632]: PROPERTY CHANGE: Adding MsiRestartManagerSessionKey property. Its value is 'd8d0cefc1249514889002637bb750a41'.
    MSI (s) (24:48) [20:50:23:632]: RESTART MANAGER: Session opened.
    MSI (s) (24:48) [20:50:23:632]: PROPERTY CHANGE: Adding MsiSystemRebootPending property. Its value is '1'.
    MSI (s) (24:48) [20:50:23:632]: TRANSFORMS property is now:
    MSI (s) (24:48) [20:50:23:632]: PROPERTY CHANGE: Adding VersionDatabase property. Its value is '200'.
    MSI (s) (24:48) [20:50:23:633]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming
    MSI (s) (24:48) [20:50:23:634]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\Favorites
    MSI (s) (24:48) [20:50:23:634]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Network Shortcuts
    MSI (s) (24:48) [20:50:23:635]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\Documents
    MSI (s) (24:48) [20:50:23:635]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Printer Shortcuts
    MSI (s) (24:48) [20:50:23:636]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Recent
    MSI (s) (24:48) [20:50:23:636]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\SendTo
    MSI (s) (24:48) [20:50:23:637]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Templates
    MSI (s) (24:48) [20:50:23:637]: SHELL32::SHGetFolderPath returned: C:\ProgramData
    MSI (s) (24:48) [20:50:23:638]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Local
    MSI (s) (24:48) [20:50:23:638]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\Pictures
    MSI (s) (24:48) [20:50:23:639]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Administrative Tools
    MSI (s) (24:48) [20:50:23:640]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Startup
    MSI (s) (24:48) [20:50:23:640]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Start Menu\Programs
    MSI (s) (24:48) [20:50:23:641]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Start Menu
    MSI (s) (24:48) [20:50:23:641]: SHELL32::SHGetFolderPath returned: C:\Users\Public\Desktop
    MSI (s) (24:48) [20:50:23:642]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Start Menu\Programs\Administrative Tools
    MSI (s) (24:48) [20:50:23:643]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Start Menu\Programs\Startup
    MSI (s) (24:48) [20:50:23:643]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Start Menu\Programs
    MSI (s) (24:48) [20:50:23:644]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Start Menu
    MSI (s) (24:48) [20:50:23:644]: SHELL32::SHGetFolderPath returned: C:\Windows\system32\config\systemprofile\Desktop
    MSI (s) (24:48) [20:50:23:645]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Templates
    MSI (s) (24:48) [20:50:23:645]: SHELL32::SHGetFolderPath returned: C:\Windows\Fonts
    MSI (s) (24:48) [20:50:23:645]: Note: 1: 2898 2: MS Sans Serif 3: MS Sans Serif 4: 0 5: 16
    MSI (s) (24:48) [20:50:23:648]: MSI_LUA: Setting MsiRunningElevated property to 1 because the install is already running elevated.
    MSI (s) (24:48) [20:50:23:648]: PROPERTY CHANGE: Adding MsiRunningElevated property. Its value is '1'.
    MSI (s) (24:48) [20:50:23:648]: PROPERTY CHANGE: Adding Privileged property. Its value is '1'.
    MSI (s) (24:48) [20:50:23:648]: Note: 1: 1402 2: HKEY_CURRENT_USER\Software\Microsoft\MS Setup (ACME)\User Info 3: 2
    MSI (s) (24:48) [20:50:23:648]: Note: 1: 1402 2: HKEY_CURRENT_USER\Software\Microsoft\MS Setup (ACME)\User Info 3: 2
    MSI (s) (24:48) [20:50:23:648]: PROPERTY CHANGE: Adding DATABASE property. Its value is 'C:\Windows\Installer\6257f6f.msi'.
    MSI (s) (24:48) [20:50:23:648]: PROPERTY CHANGE: Adding OriginalDatabase property. Its value is 'h:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi'.
    MSI (s) (24:48) [20:50:23:648]: Machine policy value 'MsiDisableEmbeddedUI' is 0
    MSI (s) (24:48) [20:50:23:648]: EEUI - Disabling MsiEmbeddedUI due to existing external or embedded UI
    MSI (s) (24:48) [20:50:23:648]: EEUI - Disabling MsiEmbeddedUI for service because it's not a quiet/basic install
    MSI (s) (24:48) [20:50:23:648]: Note: 1: 2205 2:  3: PatchPackage
    MSI (s) (24:48) [20:50:23:648]: Machine policy value 'DisableRollback' is 0
    MSI (s) (24:48) [20:50:23:648]: User policy value 'DisableRollback' is 0
    MSI (s) (24:48) [20:50:23:648]: PROPERTY CHANGE: Adding UILevel property. Its value is '2'.
    === Logging started: 8/27/2014  20:50:23 ===
    MSI (s) (24:48) [20:50:23:649]: Note: 1: 2203 2: C:\Windows\Installer\inprogressinstallinfo.ipi 3: -2147287038
    MSI (s) (24:48) [20:50:23:649]: APPCOMPAT: [DetectVersionLaunchCondition] Launch condition already passes.
    MSI (s) (24:48) [20:50:23:649]: PROPERTY CHANGE: Adding ACTION property. Its value is 'INSTALL'.
    MSI (s) (24:48) [20:50:23:649]: Doing action: INSTALL
    Action start 20:50:23: INSTALL.
    MSI (s) (24:48) [20:50:23:650]: Running ExecuteSequence
    MSI (s) (24:48) [20:50:23:650]: Doing action: System64Folder.12C909B6_5F69_4C4D_8EC3_C225C1607933
    MSI (s) (24:48) [20:50:23:650]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'System64Folder.12C909B6_5F69_4C4D_8EC3_C225C1607933'
    MSI (s) (24:48) [20:50:23:650]: PROPERTY CHANGE: Adding System64Folder.12C909B6_5F69_4C4D_8EC3_C225C1607933 property. Its value is 'C:\Windows\system32\'.
    Action start 20:50:23: System64Folder.12C909B6_5F69_4C4D_8EC3_C225C1607933.
    MSI (s) (24:48) [20:50:23:651]: Doing action: SystemFolder.12C909B6_5F69_4C4D_8EC3_C225C1607933
    Action ended 20:50:23: System64Folder.12C909B6_5F69_4C4D_8EC3_C225C1607933. Return value 1.
    MSI (s) (24:48) [20:50:23:651]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'SystemFolder.12C909B6_5F69_4C4D_8EC3_C225C1607933'
    MSI (s) (24:48) [20:50:23:651]: PROPERTY CHANGE: Adding SystemFolder.12C909B6_5F69_4C4D_8EC3_C225C1607933 property. Its value is 'C:\Windows\SysWOW64\'.
    Action start 20:50:23: SystemFolder.12C909B6_5F69_4C4D_8EC3_C225C1607933.
    MSI (s) (24:48) [20:50:23:651]: Doing action: SystemFolder.A6940213_CD40_4753_8BA2_E803376DECC3
    Action ended 20:50:23: SystemFolder.12C909B6_5F69_4C4D_8EC3_C225C1607933. Return value 1.
    MSI (s) (24:48) [20:50:23:652]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'SystemFolder.A6940213_CD40_4753_8BA2_E803376DECC3'
    MSI (s) (24:48) [20:50:23:652]: PROPERTY CHANGE: Adding SystemFolder.A6940213_CD40_4753_8BA2_E803376DECC3 property. Its value is 'C:\Windows\SysWOW64\'.
    Action start 20:50:23: SystemFolder.A6940213_CD40_4753_8BA2_E803376DECC3.
    MSI (s) (24:48) [20:50:23:652]: Doing action: System64Folder.A6940213_CD40_4753_8BA2_E803376DECC3
    Action ended 20:50:23: SystemFolder.A6940213_CD40_4753_8BA2_E803376DECC3. Return value 1.
    MSI (s) (24:48) [20:50:23:652]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'System64Folder.A6940213_CD40_4753_8BA2_E803376DECC3'
    MSI (s) (24:48) [20:50:23:652]: PROPERTY CHANGE: Adding System64Folder.A6940213_CD40_4753_8BA2_E803376DECC3 property. Its value is 'C:\Windows\system32\'.
    Action start 20:50:23: System64Folder.A6940213_CD40_4753_8BA2_E803376DECC3.
    MSI (s) (24:48) [20:50:23:653]: Doing action: SystemFolder.F65FD590_5BEA_48BE_8408_26F7244E8B61
    Action ended 20:50:23: System64Folder.A6940213_CD40_4753_8BA2_E803376DECC3. Return value 1.
    MSI (s) (24:48) [20:50:23:653]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'SystemFolder.F65FD590_5BEA_48BE_8408_26F7244E8B61'
    MSI (s) (24:48) [20:50:23:653]: PROPERTY CHANGE: Adding SystemFolder.F65FD590_5BEA_48BE_8408_26F7244E8B61 property. Its value is 'C:\Windows\SysWOW64\'.
    Action start 20:50:23: SystemFolder.F65FD590_5BEA_48BE_8408_26F7244E8B61.
    MSI (s) (24:48) [20:50:23:653]: Doing action: System64Folder.F65FD590_5BEA_48BE_8408_26F7244E8B61
    Action ended 20:50:23: SystemFolder.F65FD590_5BEA_48BE_8408_26F7244E8B61. Return value 1.
    MSI (s) (24:48) [20:50:23:654]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'System64Folder.F65FD590_5BEA_48BE_8408_26F7244E8B61'
    MSI (s) (24:48) [20:50:23:654]: PROPERTY CHANGE: Adding System64Folder.F65FD590_5BEA_48BE_8408_26F7244E8B61 property. Its value is 'C:\Windows\system32\'.
    Action start 20:50:23: System64Folder.F65FD590_5BEA_48BE_8408_26F7244E8B61.
    MSI (s) (24:48) [20:50:23:654]: Doing action: SystemFolder.BFC13682_FB8F_4455_9724_4DDBBBF713D7
    Action ended 20:50:23: System64Folder.F65FD590_5BEA_48BE_8408_26F7244E8B61. Return value 1.
    MSI (s) (24:48) [20:50:23:654]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'SystemFolder.BFC13682_FB8F_4455_9724_4DDBBBF713D7'
    MSI (s) (24:48) [20:50:23:654]: PROPERTY CHANGE: Adding SystemFolder.BFC13682_FB8F_4455_9724_4DDBBBF713D7 property. Its value is 'C:\Windows\SysWOW64\'.
    Action start 20:50:23: SystemFolder.BFC13682_FB8F_4455_9724_4DDBBBF713D7.
    MSI (s) (24:48) [20:50:23:655]: Doing action: System64Folder.BFC13682_FB8F_4455_9724_4DDBBBF713D7
    Action ended 20:50:23: SystemFolder.BFC13682_FB8F_4455_9724_4DDBBBF713D7. Return value 1.
    MSI (s) (24:48) [20:50:23:655]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'System64Folder.BFC13682_FB8F_4455_9724_4DDBBBF713D7'
    MSI (s) (24:48) [20:50:23:655]: PROPERTY CHANGE: Adding System64Folder.BFC13682_FB8F_4455_9724_4DDBBBF713D7 property. Its value is 'C:\Windows\system32\'.
    Action start 20:50:23: System64Folder.BFC13682_FB8F_4455_9724_4DDBBBF713D7.
    MSI (s) (24:48) [20:50:23:655]: Doing action: SystemFolder.1114972D_590D_4AB6_BA2E_779928CEDCC2
    Action ended 20:50:23: System64Folder.BFC13682_FB8F_4455_9724_4DDBBBF713D7. Return value 1.
    MSI (s) (24:48) [20:50:23:656]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'SystemFolder.1114972D_590D_4AB6_BA2E_779928CEDCC2'
    MSI (s) (24:48) [20:50:23:656]: PROPERTY CHANGE: Adding SystemFolder.1114972D_590D_4AB6_BA2E_779928CEDCC2 property. Its value is 'C:\Windows\SysWOW64\'.
    Action start 20:50:23: SystemFolder.1114972D_590D_4AB6_BA2E_779928CEDCC2.
    MSI (s) (24:48) [20:50:23:656]: Doing action: System64Folder.1114972D_590D_4AB6_BA2E_779928CEDCC2
    Action ended 20:50:23: SystemFolder.1114972D_590D_4AB6_BA2E_779928CEDCC2. Return value 1.
    MSI (s) (24:48) [20:50:23:656]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'System64Folder.1114972D_590D_4AB6_BA2E_779928CEDCC2'
    MSI (s) (24:48) [20:50:23:656]: PROPERTY CHANGE: Adding System64Folder.1114972D_590D_4AB6_BA2E_779928CEDCC2 property. Its value is 'C:\Windows\system32\'.
    Action start 20:50:23: System64Folder.1114972D_590D_4AB6_BA2E_779928CEDCC2.
    MSI (s) (24:48) [20:50:23:657]: Doing action: LaunchConditions
    Action ended 20:50:23: System64Folder.1114972D_590D_4AB6_BA2E_779928CEDCC2. Return value 1.
    Action start 20:50:23: LaunchConditions.
    MSI (s) (24:48) [20:50:23:657]: Skipping action: CcmSwitchToRepairMode (condition is false)
    MSI (s) (24:48) [20:50:23:657]: Doing action: AppSearch
    Action ended 20:50:23: LaunchConditions. Return value 1.
    Action start 20:50:23: AppSearch.
    MSI (s) (24:48) [20:50:23:658]: Note: 1: 2262 2: Signature 3: -2147287038
    MSI (s) (24:48) [20:50:23:658]: Note: 1: 2262 2: Signature 3: -2147287038
    MSI (s) (24:48) [20:50:23:659]: PROPERTY CHANGE: Modifying CCMINSTALLDIR property. Its current value is 'h:\Program Files\SMS_CCM'. Its new value: 'C:\Windows\CCM\'.
    MSI (s) (24:48) [20:50:23:659]: Note: 1: 2262 2: Signature 3: -2147287038
    MSI (s) (24:48) [20:50:23:659]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE32\SOFTWARE\Microsoft\CCM\Embedded 3: 2
    MSI (s) (24:48) [20:50:23:659]: Note: 1: 2262 2: Signature 3: -2147287038
    MSI (s) (24:48) [20:50:23:659]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE32\Software\Microsoft\CCM\Logging\DebugLogging 3: 2
    MSI (s) (24:48) [20:50:23:660]: Note: 1: 2262 2: Signature 3: -2147287038
    MSI (s) (24:48) [20:50:23:660]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE32\SOFTWARE\Microsoft\SMS\IIS 3: 2
    MSI (s) (24:48) [20:50:23:660]: Note: 1: 2262 2: Signature 3: -2147287038
    MSI (s) (24:48) [20:50:23:660]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE32\SOFTWARE\Microsoft\SMS\MP 3: 2
    MSI (s) (24:48) [20:50:23:660]: Note: 1: 2262 2: Signature 3: -2147287038
    MSI (s) (24:48) [20:50:23:660]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE32\SOFTWARE\Microsoft\SMS\MP 3: 2
    MSI (s) (24:48) [20:50:23:660]: Note: 1: 2262 2: Signature 3: -2147287038
    MSI (s) (24:48) [20:50:23:661]: Skipping action: CcmAbortIfEmbeddedExists (condition is false)
    MSI (s) (24:48) [20:50:23:661]: Doing action: CCPSearch
    Action ended 20:50:23: AppSearch. Return value 1.
    MSI (s) (24:48) [20:50:23:661]: Note: 1: 2205 2:  3: CCPSearch
    MSI (s) (24:48) [20:50:23:661]: Note: 1: 2228 2:  3: CCPSearch 4: SELECT `Signature_` FROM `CCPSearch`
    Action start 20:50:23: CCPSearch.
    MSI (s) (24:48) [20:50:23:661]: Doing action: RMCCPSearch
    Action ended 20:50:23: CCPSearch. Return value 0.
    MSI (s) (24:48) [20:50:23:662]: Note: 1: 2205 2:  3: CCPSearch
    MSI (s) (24:48) [20:50:23:662]: Note: 1: 2228 2:  3: CCPSearch 4: SELECT `Signature_` FROM `CCPSearch`
    Action start 20:50:23: RMCCPSearch.
    MSI (s) (24:48) [20:50:23:662]: Doing action: ValidateProductID
    Action ended 20:50:23: RMCCPSearch. Return value 0.
    Action start 20:50:23: ValidateProductID.
    MSI (s) (24:48) [20:50:23:662]: Skipping action: CcmSetInstallDir32 (condition is false)
    MSI (s) (24:48) [20:50:23:662]: Doing action: CcmSetInstallDir64
    Action ended 20:50:23: ValidateProductID. Return value 1.
    MSI (s) (24:48) [20:50:23:663]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'CcmSetInstallDir64'
    MSI (s) (24:48) [20:50:23:663]: PROPERTY CHANGE: Adding TARGETDIR property. Its value is 'C:\Windows\CCM'.
    Action start 20:50:23: CcmSetInstallDir64.
    MSI (s) (24:48) [20:50:23:663]: Doing action: CcmSetInstallDirFromCmdLine
    Action ended 20:50:23: CcmSetInstallDir64. Return value 1.
    MSI (s) (24:48) [20:50:23:664]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'CcmSetInstallDirFromCmdLine'
    MSI (s) (24:48) [20:50:23:664]: PROPERTY CHANGE: Modifying TARGETDIR property. Its current value is 'C:\Windows\CCM'. Its new value: 'C:\Windows\CCM\'.
    Action start 20:50:23: CcmSetInstallDirFromCmdLine.
    MSI (s) (24:48) [20:50:23:664]: Doing action: CcmSetPrimaryFolder
    Action ended 20:50:23: CcmSetInstallDirFromCmdLine. Return value 1.
    MSI (s) (24:48) [20:50:23:664]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'CcmSetPrimaryFolder'
    MSI (s) (24:48) [20:50:23:664]: PROPERTY CHANGE: Adding PRIMARYFOLDER property. Its value is 'TARGETDIR'.
    Action start 20:50:23: CcmSetPrimaryFolder.
    MSI (s) (24:48) [20:50:23:665]: Doing action: FindRelatedProducts
    Action ended 20:50:23: CcmSetPrimaryFolder. Return value 1.
    Action start 20:50:23: FindRelatedProducts.
    MSI (s) (24:48) [20:50:23:665]: PROPERTY CHANGE: Adding SMSSP1COLOCDOWNGRADE property. Its value is '{8864FB91-94EE-4F16-A144-0D82A232049D}'.
    MSI (s) (24:48) [20:50:23:666]: Skipping action: SmsDetectUnsupportedUpgrade (condition is false)
    MSI (s) (24:48) [20:50:23:666]: Skipping action: SmsDetectDowngrade (condition is false)
    MSI (s) (24:48) [20:50:23:666]: Skipping action: CcmDetectUnsupportedUpgrade (condition is false)
    MSI (s) (24:48) [20:50:23:666]: Doing action: SmsDetectColocationDowngrade
    Action ended 20:50:23: FindRelatedProducts. Return value 1.
    MSI (s) (24:48) [20:50:23:666]: Note: 1: 2235 2:  3: ExtendedType 4: SELECT `Action`,`Type`,`Source`,`Target`, NULL, `ExtendedType` FROM `CustomAction` WHERE `Action` = 'SmsDetectColocationDowngrade'
    Action start 20:50:23: SmsDetectColocationDowngrade.
    MSI (s) (24:48) [20:50:23:666]: Product: ConfigMgr Management Point -- A newer version of the Configuration Manager Client is installed. Cannot continue installing this version of the management point.
    A newer version of the Configuration Manager Client is installed. Cannot continue installing this version of the management point.
    Action ended 20:50:23: SmsDetectColocationDowngrade. Return value 3.
    Action ended 20:50:23: INSTALL. Return value 3.
    Property(S): UpgradeCode = {ABD0F60F-1622-4311-8989-106B60D784FF}
    Property(S): TARGETDIR = C:\Windows\CCM\
    Property(S): ALLUSERS = 1
    Property(S): ErrorDialog = ErrorDialog
    Property(S): ProductName = ConfigMgr Management Point
    Property(S): ProductCode = {6CED3AB0-05AF-4C81-8DBE-A62661C26F40}
    Property(S): PackageCode = {5CBAF9F8-A298-49C0-B874-D0F5F0F39DB4}
    Property(S): Manufacturer = Microsoft Corporation
    Property(S): ProductVersion = 5.00.7804.1000
    Property(S): ProductLanguage = 1033
    Property(S): SMSCWSREGKEYNAME = MPCWSPath
    Property(S): CcmCheckRepairNotInstalled_ActionText = Abort repair if the product has not been installed.
    Property(S): CcmSwitchToRepairMode_ActionText = Product has been installed. Switch to repair mode for this installation.
    Property(S): CcmSuppressReboot_ActionText = Suppress machine reboot after installation.
    Property(S): CcmCheckFreeDiskSpace_ActionText = Check if the target volumn has enough space for the installation.
    Property(S): CcmCheckFreeDiskSpace2_ActionText = Check if the target volumn has enough space for the installation.
    Property(S): CcmSetInstallDirFromCmdLine_ActionText = Property custom action for setting install directory from command line.
    Property(S): CcmCreateWmiNamespacesInit_ActionText = Processes the table CcmWmiNamespace and sends the context to CcmCreateWmiNamespaces.
    Property(S): CcmCreateWmiNamespaces_ActionText = Creates the WMI namespaces found in the CcmWmiNamespace table
    Property(S): CcmCreateWmiNamespacesRollback_ActionText = Calls CcmRemoveWmiNamespaces. Deletes the WMI namespaces.
    Property(S): CcmRemoveWmiNamespacesInit_ActionText = Processes the table CcmWmiNamespace and sends the context to CcmRemoveWmiNamespaces.
    Property(S): CcmRemoveWmiNamespaces_ActionText = Deletes WMI namespaces.
    Property(S): CcmRegisterWmiMofFilesInit_ActionText = Queues MOF files in the CcmWmiMofFile table to be compiled.
    Property(S): CcmRegisterWmiMofFile_ActionText = Compiles MOF files that were queued by CcmRegisterWmiMofFilesInit.
    Property(S): CcmWmiRollback_ActionText = Deletes the existin site policy config and then recompiles MOF to restore old WMI instances.
    Property(S): CcmDeleteWmiBackup_ActionText = Deletes the back up mof of the wmi namespace created for rolling back purposes.
    Property(S): CcmRemoveWmiObjectsInit_ActionText = Queries the CcmWmiObject table for WMI objects to be removed.
    Property(S): CcmRemoveWmiObjects_ActionText = Removes WMI objects found by CcmRemoveWmiObjectsInit.
    Property(S): CcmRemoveWmiObjectsRollback_ActionText = Calls CcmRemoveWmiObjects. Removes WMI objects found by CcmRemoveWmiObjectsInit.
    Property(S): CcmCreateIISVirtualDirectoriesInit_ActionText = Processes the CcmIISVirtualDirectory table and passes that information to CcmCreateIISVirtualDirectories to create the virtual directories.
    Property(S): CcmCreateIISVirtualDirectories_ActionText = Creates the virtual directories specified in the CcmIISVirtualDirectory table.
    Property(S): CcmRollbackIISVirtualDirectories_ActionText = Calls CcmRemoveIISVirtualDirectories. Removes IIS Virtual Directories found in CcmRemoveIISVirtualDirectoriesInit.
    Property(S): CcmRemoveIISVirtualDirectories_ActionText = Removes IIS Virtual Directories found in CcmRemoveIISVirtualDirectoriesInit.
    Property(S): CcmRemoveIISVirtualDirectoriesInit_ActionText = Queries the CcmIISVirtualDirectory table for IIS Virtual Directories to be removed.
    Property(S): CcmCreateIISApplicationPoolsInit_ActionText = Processes the CcmIISAplicationPool table and passes that context to CcmCreateIISAplicationPools custom action.
    Property(S): CcmCreateIISApplicationPools_ActionText = Creates the application pools specified in the CcmIISAplicationPools table.
    Property(S): CcmCreateIISApplicationPoolsRollback_ActionText = Calls CcmRemoveIISApplicationPools. Removes IIS Application Pools found in CcmRemoveIISApplicationPoolsInit.
    Property(S): CcmRemoveIISApplicationPoolsInit_ActionText = Queries the CcmIISApplicationPool table for IIS Application Pools to be removed.
    Property(S): CcmRemoveIISApplicationPools_ActionText = Removes IIS Application Pools found in CcmRemoveIISApplicationPoolsInit.
    Property(S): CcmDetectFilesInUseRemoveInit_ActionText = Detect if files are in used at uninstallation.
    Property(S): CcmDetectFilesInUseInit_ActionText = Detects file in use.
    Property(S): CcmDetectFilesInUse_ActionText = Moves files that are in use so that they will be deleted upon the next reboot.
    Property(S): CcmDetectFilesInUseRollback_ActionText = Rolls back files moved by CcmDetectFilesInUse.
    Property(S): CcmDetectFilesInUseCommit_ActionText = Commits action of CcmDetectFileInUse. After this we cannot rollback.
    Property(S): CcmDetectFilesInUseRemoveRollback_ActionText = Calls CcmDetectFilesInUseRollback. Rolls back the files moved by CcmDetectFilesInUse.
    Property(S): CcmDetectFilesInUseRemoveCommit_ActionText = Calls CcmDetectFilesInUseCommit. Commits action of CcmDetectFileInUse. After this the action cannot be rolled back.
    Property(S): CcmLookupAccountNames_ActionText = Looks up the name of the Administrators group, Users group, and Creator Owner account, then sets the properties CcmAdministratorGroupName, CcmUsersGroupName, and CcmCreatorOwnerAccountName.
    Property(S): CcmRegisterPerfCountersInit_ActionText = Processes the CcmPerfApplication table for components that will be registering a performance counter.
    Property(S): CcmRegisterPerfCounters_ActionText = Registers performance counters gathered in the CcmRegisterPerfCountersInit action
    Property(S): CcmUnregisterPerfCountersInit_ActionText = Processes the CcmPerfApplication table for components that will be unregistering a performance counter.
    Property(S): CcmUnregisterPerfCounters_ActionText = Removes performance counters gathered in the CcmUnregisterPerfCountersInit action
    Property(S): CcmRegisterPerfCountersRollback_ActionText = Rolls back any changes made by CcmRegisterPerfCounters if install fails.
    Property(S): CcmUnloadWmiProvidersInit_ActionText = Enumerates component table and builds a list of files that will be installed
    Property(S): CcmUnloadWmiProviders_ActionText = Enumerates all providers and unloads them, verifies they are unloaded, and then reloads them.
    Property(S): CcmTypelibRollbackInit_ActionText = Queues a list of type libraries to be registered on rollback.
    Property(S): CcmTypelibRollback_ActionText = In the event of install failing, this event rolls back the type libraries to the state before install started.
    Property(S): CcmSetObjectSecurityInit_ActionText = Queries the CcmObjectSecurity table and passes this information to CcmSetObjectSecurity.
    Property(S): CcmSetObjectSecurity_ActionText = Applying security permissions
    Property(S): CcmSetInstallDir32_ActionText = Property action for setting installation directory for Configuration Manager Client on 32-bit platform.
    Property(S): CcmSetInstallDir64_ActionText = Property action for setting installation directory for Configuration Manager Client on 64-bit platform.
    Property(S): CcmSetPrimaryFolder_ActionText = Property action for setting target installation folder.
    Property(S): PRIMARYFOLDER = TARGETDIR
    Property(S): VersionNT64 = 603
    Property(S): CCMINSTALLDIR = C:\Windows\CCM\
    Property(S): System64Folder.12C909B6_5F69_4C4D_8EC3_C225C1607933 = C:\Windows\system32\
    Property(S): SystemFolder.12C909B6_5F69_4C4D_8EC3_C225C1607933 = C:\Windows\SysWOW64\
    Property(S): CCMEXECFILEKEY = [#CcmExec_exe.A6940213_CD40_4753_8BA2_E803376DECC3]
    Property(S): CcmDetectUpgradeOldClient_Message = A previous version of the Configuration Manager Client is installed. Please upgrade the client to Configuration Manager 2012 before attempting to upgrade.
    Property(S): SmsDetectUpgradeOldMP_Message = A previous version of the Configuration Manager Management Point is installed. Please upgrade the management point to Configuration Manager 2012 before attempting to upgrade.
    Property(S): SmsDetectUnsupportedUpgrade_ActionText = Detect if a previous version of the Configuration Manager Management Point is installed before upgrading Configuration Manager Client.
    Property(S): CcmDetectUnsupportedUpgrade_ActionText = Detect if a previous version of the Configuration Manager Client is installed before upgrading Configuration Manager Management Point.
    Property(S): CcmAbortIfEmbeddedExists_ActionText = Abort installation if the Configuration Manager Client Embedded version is installed.
    Property(S): CcmRegisterHostingConfigurationInit_ActionText = Gathers configuration for Configuration Manager Client service to be registered on the system.
    Property(S): CcmRegisterHostingConfiguration_ActionText = Register configuration for Configuration Manager Client service.
    Property(S): CcmRegisterHostedApplicationsInit_ActionText = Gathers hosted out-of-proc DCOM applications running inside of Configuration Manager Client to be registered on the system.
    Property(S): CcmRegisterHostedApplications_ActionText = Register hosted out-of-proc DCOM applications running inside of Configuration Manager Client.
    Property(S): CcmRegisterHostedApplicationsRollback_ActionText = Rollback the registration of hosted out-of-proc DCOM applications running inside of Configuration Manager Client.
    Property(S): CcmRemoveHostedApplicationsInit_ActionText = Prepare to remove the registration of hosted out-of-proc DCOM applications running inside of Configuration Manager Client.
    Property(S): CcmRemoveHostedApplications_ActionText = Remove the registration of hosted out-of-proc DCOM applications running inside of Configuration Manager Client.
    Property(S): CcmRegisterEndpointsInit_ActionText = Gathers information such as log file name on each endpoint to be registered on the system.
    Property(S): CcmRegisterEndpoint_ActionText = Registers endpoint gathered in the action CcmRegisterEndpointsInit with WMI.
    Property(S): CcmRegisterEndpointRollback_ActionText = In the event of a failed installation, this action rolls back the changes from CcmRegisterEndpoint.
    Property(S): CcmRemoveEndpointsInit_ActionText = Gathers information for each endpoint to be removed from the system.
    Property(S): CcmRemoveEndpoint_ActionText = Removes endpoint gathered in the action CcmRemoveEndpointsInit with WMI.
    Property(S): CcmRegisterSystemTasksInit_ActionText = Processes the CcmSystemTask table and passes this information to CcmRegisterSystemTask.
    Property(S): CcmRegisterSystemTask_ActionText = Registers a System Task with WMI.
    Property(S): CcmRegisterSystemTaskRollback_ActionText = Rolls back the changes made by CcmRegisterSystemTask.
    Property(S): CcmRemoveSystemTasksInit_ActionText = Processes the CcmSystemTask table and passes this information to CcmRemoveSystemTask.
    Property(S): CcmRemoveSystemTask_ActionText = Deletes a System Task from WMI.
    Property(S): CcmRegisterProduct_ActionText = If product is registered in MSI database, then product is registered with WMI.
    Property(S): CcmRegisterProductRollback_ActionText = Calls CcmUnregisterProduct. Deletes the instance from the WMI in the Configuration Manager namespace using the ProductCode instance in the session.
    Property(S): CcmUnregisterProduct_ActionText = Deletes the instance from WMI in ccm namespace using the ProductCode instance in the session.
    Property(S): CcmRegisterComponentsInit_ActionText = Generates the list of components for CcmRegisterComponets action to register.
    Property(S): CcmRegisterComponents_ActionText = Registers components passed in from CcmRegisterComponentsInit
    Property(S): CcmRegisterComponentsRollback_ActionText = In the event of a failed installation, this action rolls back the changes from CcmRegisterComponents.
    Property(S): CcmUnregisterComponentsInit_ActionText = Generates the list of components for CcmUnregisterComponets action to unregister.
    Property(S): CcmUnregisterComponents_ActionText = Unregisters components passed in from the action CcmUnregisterComponentsInit.
    Property(S): CcmSetupLoggingInit_ActionText = Gathers log file information from the LogFile table and passes this information to CcmSetupLogging.
    Property(S): CcmSetupLogging_ActionText = Sets component logging information in WMI.
    Property(S): CcmStopService_ActionText = Stops the ccmexec service.
    Property(S): CcmStopServiceRollback_ActionText = Calls CcmStartService. Starts the ccmexec service.
    Property(S): CcmStartService_ActionText = Starts the ccmexec service.
    Property(S): CcmClearServiceSetupStamp_ActionText = Clear the time stamp for blocking the ccmexec service from starting up during upgrade.
    Property(S): CcmSetServiceConfigInit_ActionText = Gathers ServiceData and then queues actions CcmSetServiceConfig and CcmMigrateMessagingQueues.
    Property(S): CcmSetServiceConfig_ActionText = Sets WMI ServiceRootDir and configures CCMEXEC service.
    Property(S): CcmConfigDCOMInit_ActionText = Processes the CcmDCOMAplication table and  checks to see if the DCOM Component is being updated. If so, passes that information to custom action CcmConfigDCOM.
    Property(S): CcmConfigDCOM_ActionText = Configures registry key permissions for the DCOM Components passed from CcmConfigDCOMInit.
    Property(S): CcmFixupServiceConfigInit_ActionText = Gathers the services or load ordering groups which must be started before ccmexec starts.
    Property(S): CcmFixupServiceConfig_ActionText = Sets the services or load ordering groups which must be started before ccmexec can be started.
    Property(S): CcmRemoveService_ActionText = Removes BITS jobs and deletes the messaging queues.
    Property(S): CcmRemoveLanternDocuments_ActionText = Removing documents from Microsoft Policy Platform that have been submitted by Configuration Manager authority.
    Property(S): CcmSetPortConfigInit_ActionText = This custom action specifies the port the client should use when communicating with the management point and the server locator point.
    Property(S): CcmSetHttpsConfigInit_ActionText = This custom action configures the https port and http state.
    Property(S): CcmPreserveLastStateSerialNum_ActionText = Custom action to preserve last state message serial number.
    Property(S): CcmInitializePolicyInit_ActionText = Gather default policy information.
    Property(S): CcmInitializePolicy_ActionText = Sets and initializes default policy.
    Property(S): CcmMigratePolicySettingsInit_ActionText = Custom action to schedule the deferred execution of CcmMigratePolicySettings custom action.
    Property(S): CcmMigratePolicySettings_ActionText = Compiles Mof file to migrate root\ccm\Policy namespace schema from Pre-V4 Beta2 to V4 and above.
    Property(S): CcmMigratePolicySettingsCommit_ActionText = Just deletes the temporary MOF file.
    Property(S): CcmMigratePolicySettingsRollback_ActionText = Just deletes the temporary MOF file. Actual Rollback is done by the rollback action that rollbacks root\ccm namespace.
    Property(S): ExpandCcmExecFileKey_ActionText = Property action for setting CcmExec file key.
    Property(S): CcmMinAppVersion = 5.00.7000.0000
    Property(S): CcmMaxAppVersion = 5.00.9000.0000
    Property(S): SystemFolder.A6940213_CD40_4753_8BA2_E803376DECC3 = C:\Windows\SysWOW64\
    Property(S): System64Folder.A6940213_CD40_4753_8BA2_E803376DECC3 = C:\Windows\system32\
    Property(S): SystemFolder.F65FD590_5BEA_48BE_8408_26F7244E8B61 = C:\Windows\SysWOW64\
    Property(S): System64Folder.F65FD590_5BEA_48BE_8408_26F7244E8B61 = C:\Windows\system32\
    Property(S): USELEGACYSTATEMESSAGESTORE = 1
    Property(S): CcmValidateCustomWebSite_ActionText = This custom action validates that either the custom website or default website (if a custom website is not specified) can be used.
    Property(S): CcmValidateServerConfig_ActionText = Validates that IIS, BITS and WebDAV is installed and properly configured setup.
    Property(S): CcmLookupIISAnonymousAccountName_ActionText = Looks up the IIS AnonymousUserName and then sets the IISAnonymousUserAccount property to this value.
    Property(S): CcmSetServiceMPConfigInit_ActionText = Gathers Incoming and Outgoing directories and virtual directories for the MP. Queues the action CcmSetServiceMPConfig.
    Property(S): CcmSetServiceMPConfig_ActionText = Sets Incoming and Outgoing directories and virtual directories in WMI.
    Property(S): CcmSetServerDataRoot_ActionText = Property action for setting service data root folder.
    Property(S): CcmSetServerDataRootInstallDir_ActionText = Property action for setting service data folder.
    Property(S): CcmIncomingVDirName = CCM_Incoming
    Property(S): SystemFolder.BFC13682_FB8F_4455_9724_4DDBBBF713D7 = C:\Windows\SysWOW64\
    Property(S): System64Folder.BFC13682_FB8F_4455_9724_4DDBBBF713D7 = C:\Windows\system32\
    Property(S): CCMSERVERDATAROOT = h:\Program Files\Microsoft Configuration Manager
    Property(S): CcmSystemVDirName = CCM_System
    Property(S): CcmSystemRegVDirName = CCM_System_WindowsAuth
    Property(S): CcmSystemAltAuthVDirName = CCM_System_AltAuth
    Property(S): SMSCACHEDIR = Default
    Property(S): SMSCACHEFLAGS = Default
    Property(S): DISABLESITEOPT = Default
    Property(S): DISABLECACHEOPT = Default
    Property(S): SMSCACHESIZE = 5120
    Property(S): SmsShellNotify_ActionText = Notifies the shell for the file-association icon changes.
    Property(S): CCMINSTALLMSMQ = FALSE
    Property(S): CCMINSTALLMP = 1
    Property(S): ARPSYSTEMCOMPONENT = 1
    Property(S): ARPNOREMOVE = 1
    Property(S): ARPNOMODIFY = 1
    Property(S): CCMENABLELOGGING_Default = FALSE
    Property(S): CCMLOGLEVEL_Default = 1
    Property(S): CCMLOGMAXSIZE_Default = 2000000
    Property(S): CCMLOGMAXHISTORY_Default = 1
    Property(S): SecureCustomProperties = CCMENABLELOGGING;CCMLOGLEVEL;CCMLOGMAXHISTORY;CCMLOGMAXSIZE;CCMDEBUGLOGGING;CCMOSINSTALLPATHS;CCMINSTALLMSMQ;CCMINSTALLMP;SMSUPGRADEPRODUCTS;CCMSERVERDATAROOT;SMSUPLEVELPRODUCTS;USESMSPORTS;SMSPORTS;CCMHTTPPORT;SMSSP1COLOCDOWNGRADE;USESMSSSLPORTS;SMSSSLPORTS;SMSSSLSTATE;CCMHTTPSPORT;CCMHTTPSCERTNAME;SMSFWKUPGRADEFROMPREV4;CCMFWKUPGRADEFROMPREV4;CLIENTFWKUPGRADEFROMCM2007;SMSCWS;CCMSHAREMODE
    Property(S): AdminProperties = CCMENABLELOGGING;CCMLOGLEVEL;CCMLOGMAXHISTORY;CCMLOGMAXSIZE;CCMDEBUGLOGGING;CCMOSINSTALLPATHS;CCMINSTALLMSMQ;CCMINSTALLMP;CCMSERVERDATAROOT;CCMALLOWSILENTREBOOT;CCMHTTPPORT;CCMHTTPSPORT;CCMHTTPSCERTNAME;SMSCWS
    Property(S): CcmDefaultPolicyAuthorityPriority = 10
    Property(S): SmsDetectColocationDowngrade_Message = A newer version of the Configuration Manager Client is installed. Cannot continue installing this version of the management point.
    Property(S): SmsDetectColocationDowngrade_ActionText = Detect if a newer version of the Configuration Management Client is installed before installing the Configuration Manager Management Point.
    Property(S): SmsDetectDowngrade_ActionText = Check if a newer version of the Configuration Manager Client is already installed.
    Property(S): SmsMpRepairSucceeded_ActionText = Sends a wmi event to indicate MP repair succeeded.
    Property(S): SmsDetectMSXMLRebootRequired_ActionText = Tries to create an instance of SAXXMLReader to determine if a reboot is required.
    Property(S): SmsMpSetDefaultPolicyAuthority_ActionText = Set default policy authority for the Configuration Manager Management Point.
    Property(S): SmsMpSerializedKeyExist_ActionText = Wait for the Configuration Manager Management Point serialized key to exist.
    Property(S): ButtonText_Next = &Next >
    Property(S): ButtonText_Back = < &Back
    Property(S): ButtonText_Cancel = &Cancel
    Property(S): ButtonText_Finish = &Finish
    Property(S): ButtonText_Install = &Install
    Property(S): ButtonText_Close = &Close
    Property(S): ButtonText_OK = &OK
    Property(S): ButtonText_Abort = &Abort
    Property(S): ButtonText_Ignore = &Ignore
    Property(S): ButtonText_No = &No
    Property(S): ButtonText_Yes = &Yes
    Property(S): ButtonText_Retry = &Retry
    Property(S): ButtonText_Exit = &Exit
    Property(S): FilesInUse_Info = Setup has detected that it needs to update some files that are currently in use by other processes.
    To prevent having to reboot the machine, please close the following applications:
    Property(S): DefaultUIFont = DefaultDlgFont
    Property(S): DialogBox_Title = ConfigMgr Management Point Setup
    Property(S): WelcomeDialog_Info = This will install the ConfigMgr Management Point.
    Property(S): InstallDialog_Title = Install
    Property(S): InstallDialog_SubTitle = The product is now ready to install
    Property(S): InstallDialog_Info = Click Next to proceed.
    Property(S): ProgressDialog_Title = Please Wait
    Property(S): ProgressDialog_SubTitle = Setup is configuring your system.
    Property(S): CompleteDialog_Title = Setup Complete
    Property(S): CompleteDialog_SubTitle = Setup has finished updating your system.
    Property(S): CompleteDialog_Info = Setup was successful.
    Property(S): UserExitDialog_Title = Setup Aborted
    Property(S): UserExitDialog_SubTitle = Setup was cancelled
    Property(S): UserExitDialog_Info = The ConfigMgr Management Point setup was cancelled.
    Property(S): InstallErrorDialog_Title = Setup Aborted
    Property(S): InstallErrorDialog_SubTitle = Setup failed
    Property(S): InstallErrorDialog_Info = Setup encountered an error and could not continue.
    Property(S): SystemFolder.1114972D_590D_4AB6_BA2E_779928CEDCC2 = C:\Windows\SysWOW64\
    Property(S): System64Folder.1114972D_590D_4AB6_BA2E_779928CEDCC2 = C:\Windows\system32\
    Property(S): SMSSP1COLOCDOWNGRADE = {8864FB91-94EE-4F16-A144-0D82A232049D}
    Property(S): MsiLogFileLocation = h:\Program Files\Microsoft Configuration Manager\logs\mpMSI.log
    Property(S): ProductState = -1
    Property(S): PackagecodeChanging = 1
    Property(S): USESMSPORTS = TRUE
    Property(S): SMSPORTS = 80
    Property(S): USESMSSSLPORTS = TRUE
    Property(S): SMSSSLPORTS = 443
    Property(S): USESMSSSL = TRUE
    Property(S): SMSSSLSTATE = 0
    Property(S): CCMENABLELOGGING = TRUE
    Property(S): CCMLOGLEVEL = 1
    Property(S): CCMLOGMAXSIZE = 1000000
    Property(S): CCMLOGMAXHISTORY = 1
    Property(S): CURRENTDIRECTORY = H:\Program Files\Microsoft Configuration Manager\bin\x64
    Property(S): CLIENTUILEVEL = 3
    Property(S): MSICLIENTUSESEXTERNALUI = 1
    Property(S): CLIENTPROCESSID = 6556
    Property(S): MsiRestartManagerSessionKey = d8d0cefc1249514889002637bb750a41
    Property(S): VersionDatabase = 200
    Property(S): MsiSystemRebootPending = 1
    Property(S): VersionMsi = 5.00
    Property(S): VersionNT = 603
    Property(S): WindowsBuild = 9600
    Property(S): ServicePackLevel = 0
    Property(S): ServicePackLevelMinor = 0
    Property(S): MsiNTProductType = 3
    Property(S): MsiNTSuiteDataCenter = 1
    Property(S): WindowsFolder = C:\Windows\
    Property(S): WindowsVolume = C:\
    Property(S): System64Folder = C:\Windows\system32\
    Property(S): SystemFolder = C:\Windows\SysWOW64\
    Property(S): RemoteAdminTS = 1
    Property(S): TempFolder = C:\Windows\TEMP\
    Property(S): ProgramFilesFolder = C:\Program Files (x86)\
    Property(S): CommonFilesFolder = C:\Program Files (x86)\Common Files\
    Property(S): ProgramFiles64Folder = C:\Program Files\
    Property(S): CommonFiles64Folder = C:\Program Files\Common Files\
    Property(S): AppDataFolder = C:\Windows\system32\config\systemprofile\AppData\Roaming\
    Property(S): FavoritesFolder = C:\Windows\system32\config\systemprofile\Favorites\
    Property(S): NetHoodFolder = C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Network Shortcuts\
    Property(S): PersonalFolder = C:\Windows\system32\config\systemprofile\Documents\
    Property(S): PrintHoodFolder = C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Printer Shortcuts\
    Property(S): RecentFolder = C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\Recent\
    Property(S): SendToFolder = C:\Windows\system32\config\systemprofile\AppData\Roaming\Microsoft\Windows\SendTo\
    Property(S): TemplateFolder = C:\ProgramData\Microsoft\Windows\Templates\
    Property(S): CommonAppDataFolder = C:\ProgramData\
    Property(S): LocalAppDataFolder = C:\Windows\system32\config\systemprofile\AppData\Local\
    Property(S): MyPicturesFolder = C:\Windows\system32\config\systemprofile\Pictures\
    Property(S): AdminToolsFolder = C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Administrative Tools\
    Property(S): StartupFolder = C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Startup\
    Property(S): ProgramMenuFolder = C:\ProgramData\Microsoft\Windows\Start Menu\Programs\
    Property(S): StartMenuFolder = C:\ProgramData\Microsoft\Windows\Start Menu\
    Property(S): DesktopFolder = C:\Users\Public\Desktop\
    Property(S): FontsFolder = C:\Windows\Fonts\
    Property(S): GPTSupport = 1
    Property(S): OLEAdvtSupport = 1
    Property(S): ShellAdvtSupport = 1
    Property(S): MsiAMD64 = 6
    Property(S): Msix64 = 6
    Property(S): Intel = 6
    Property(S): PhysicalMemory = 5372
    Property(S): VirtualMemory = 4017
    Property(S): AdminUser = 1
    Property(S): MsiTrueAdminUser = 1
    Property(S): LogonUser = SYSTEM
    Property(S): UserSID = S-1-5-18
    Property(S): UserLanguageID = 1033
    Property(S): ComputerName = [servername]
    Property(S): SystemLanguageID = 1033
    Property(S): ScreenX = 1024
    Property(S): ScreenY = 768
    Property(S): CaptionHeight = 23
    Property(S): BorderTop = 1
    Property(S): BorderSide = 1
    Property(S): TextHeight = 16
    Property(S): TextInternalLeading = 3
    Property(S): ColorBits = 32
    Property(S): TTCSupport = 1
    Property(S): Time = 20:50:23
    Property(S): Date = 8/27/2014
    Property(S): MsiNetAssemblySupport = 4.0.30319.33440
    Property(S): MsiWin32AssemblySupport = 6.3.9600.16384
    Property(S): RedirectedDllSupport = 2
    Property(S): MsiRunningElevated = 1
    Property(S): Privileged = 1
    Property(S): DATABASE = C:\Windows\Installer\6257f6f.msi
    Property(S): OriginalDatabase = h:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi
    Property(S): UILevel = 2
    Property(S): ACTION = INSTALL
    === Logging stopped: 8/27/2014  20:50:23 ===
    MSI (s) (24:48) [20:50:23:717]: Note: 1: 1708
    MSI (s) (24:48) [20:50:23:717]: Product: ConfigMgr Management Point -- Installation operation failed.
    MSI (s) (24:48) [20:50:23:718]: Windows Installer installed the product. Product Name: ConfigMgr Management Point. Product Version: 5.00.7804.1000. Product Language: 1033. Manufacturer: Microsoft Corporation. Installation success or error status: 1603.
    MSI (s) (24:48) [20:50:23:721]: Deferring clean up of packages/files, if any exist
    MSI (s) (24:48) [20:50:23:721]: MainEngineThread is returning 1603
    MSI (s) (24:FC) [20:50:23:725]: RESTART MANAGER: Session closed.
    MSI (s) (24:FC) [20:50:23:725]: No System Restore sequence number for this installation.
    MSI (s) (24:FC) [20:50:23:726]: User policy value 'DisableRollback' is 0
    MSI (s) (24:FC) [20:50:23:726]: Machine policy value 'DisableRollback' is 0
    MSI (s) (24:FC) [20:50:23:726]: Incrementing counter to disable shutdown. Counter after increment: 0
    MSI (s) (24:FC) [20:50:23:726]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Installer\Rollback\Scripts 3: 2
    MSI (s) (24:FC) [20:50:23:726]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Installer\Rollback\Scripts 3: 2
    MSI (s) (24:FC) [20:50:23:727]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied.  Counter after decrement: -1
    MSI (c) (9C:58) [20:50:23:728]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied.  Counter after decrement: -1
    MSI (c) (9C:58) [20:50:23:728]: MainEngineThread is returning 1603
    === Verbose logging stopped: 8/27/2014  20:50:23 ===

    A newer version of the Configuration Manager Client is installed. Cannot continue installing this version of the management point.
    Action ended 20:50:23: SmsDetectColocationDowngrade. Return value 3.
    Action ended 20:50:23: INSTALL. Return value 3.
    The installer certainly thinks that you still have a previous ConfigMgr client installed. Perhaps you haven't completely removed it. Use ccmclean.exe from the SMS 2003 tool kit.
    If that fails, why not just rebuild the server - you've said that this is a fresh install. I don't like too much messing at the beginning. This can be difficult enough - you need to start with a clean installation of the product.
    Gerry Hampson | Blog:
    www.gerryhampsoncm.blogspot.ie | LinkedIn:
    Gerry Hampson | Twitter:
    @gerryhampson

  • ProClarity 6.3 PAS install fails on Windows Server 2012

    We are trying to install PAS 6.3 on Windows Server 2012 and the install fails with the following error
    The following requirements are missing:
    Windows Server 2003 SP1
    We have successfully installed on Windows Server 2008 R2, so it really isn't a Windows Server 2003 SP1 issue.
    Has anyone successfully installed on Windows Server 2012?  Is there a way to force the installer not to check for the OS?
    Thanks.
    Kevin

    I have a PAS server running in Windows 2012, by doing exactly the same pre-requisites  that you do in Windows 2008 r2 (iis, Framework, SQL ADO 2005 / 2008). With the Windows Server 2003 SP1 message you can avoid it by doing a really simple thing that
    is right click the setup file --> properties, and head to the "Compatibility Tab" and run it with compatibility mode Windows 7, also run it with Admin permissions. This let you pass by the message and let you install the product.  Remember, after  the
    installation, you need to check all the IIS config, folder permissions, that you did in Windows 2008 x64  installation. Also, the App pool needs to work with .NET 2.0 not 4.0. 
    Good luck! 
    Byron
    BNavas

  • G5 10.5.8 Combo Update codec overrun - install fails

    Hi,
    I still have my first mac, a Power Mac G5, but it has been acting as a center speaker stand for some time now. A couple of years ago it started playing up, I spent hours and pounds trying to fix it, gave up and bought a shiny new iMac. So with the festive season upon us and orders to tidy up, I thought I'd have one last try at fixing it before turning it into a drinks cabinet.
    As I recall, it all started to go wrong one day when I tried to download a large update to something. When I tried to install the update I got a Codec Overrun error and/or a Corrupt File message. As it stands today the machine is running a clean install of OSX 10.5.6 and I am failing to install the MacOSXUpdCombo10.5.8.dmg upgrade. I currently have 2 copies of the update.
    One copy on the desktop  was downloaded directly from the Apple support site. The .dmg opens and verifies OK and I can launch the MacOSXUpdCombo10.5.8.pkg. This runs through the installation sequence, past the password but finally comes up with an error message "Install Failed. The installer could not validate the contents of the 'MacOSXUpdCombo10.5.8' package. Contact the software manufacturer for assistance."
    Another copy in my downloads folder, put there by the Software Updater, doesn't get that far. It comes up with "Warning,The following disk image failed to mount. Image - MacOSXUpdCombo10.5.8.dmg, Reason - codec overrun."
    So far I have tried:-
    Memory - run third party memory checker application (can't remember which one) and found no faults.Tried different set of memory cards
    Hard disk - run all the disk check and repair utilities, re-formatted, repartitioned. Tried a different hard disk.
    OSX 10.5.6 - reinstalled from original disks several times.
    MacOSXUpdCombo10.5.8 - downloaded via Software Updater process and direct from Apple Support website. Downloaded via wi-fi, ethernet, different Mac, different PC. Always get the exact same file size.
    Resetting the PRAM etc
    New standby battery
    Installing in Safe Mode
    Swearing.
    None of this has worked. I get some different error messages but they are all variations of "codec overrun", "corrupt file" or "Install failure"
    Anyone got any other ideas? Or should I just get on with the drinks cabinet conversion?
    Thanks

    That message isn't a space available message. If you bring up Disk Utility, how does it say the partition is formatted, ie, partition format, write status, and partition map scheme? Assume SMART status is verified, yes?

  • Family Pack Leopard install fails G4 Dual 1.2Ghz

    All, I purchased the Leopard family pack and have successfully installed it on an Intel Macbook Pro and a G5 2.3Ghz DP machine - flawless, no problems during installation or after.
    However, any attempt to install on a G4 Dual 1.2Ghz + 2Gb of RAM + just bought a Seagate 500Gb Barracuda internal drive (well within the designated technical requirements), I've tried the following.
    1. Booting the G4 off the Leopard install DVD, I get the following error: Failed Install message = "The Installer could not validate the contents of the Essentials Package...".
    I can never get beyond this point. After receiving this error, the internal disk isn't even recognized on the bus - I have to pull the disk out, put it in an external case to reformat it. I've even tried a low level format and also had Seagate replace the disk thinking it was defective.
    2. I then thought it may be an issue with putting the Seagate disk in cable select mode versus master / slave configuration. The Seagate is the only hard drive in the machine. I have tried both cable select and master/slave configuration - both freeze after install, etc. without fail.
    3. Tried installing Leopard on the G4 by connecting it to the G5 in target disk mode. It installed, but routinely just freezes (NEVER had this issue with Tiger on this machine).
    I do see lots of people posting issues with the "The Installer could not validate the contents of the Essentials Package..." error.
    For the record, after successful Leopard install using technique #1 and #3 - I am also unable to run the Migration assistant - it fails every time with a kernel panic. I'm not having any trouble with the Leopard install media on any of the other 2 machines, nor did I have issues running the migration assistant.
    Any ideas are appreciated. thx,

    themdg - you said you put back your 2-512 original RAM cards and tried to install Leopard and the install failed. But my original, factory-installed RAM was third-party RAM which prevented me from installing Leopard, giving the “essentials” error. Only when I purchased RAM from Apple, and used only that RAM to install, could I get it to work correctly.
    Check your original RAM. If it is not the Apple brand, it may not work because of that, even if it was the factory-installed RAM.
    After I installed Leopard with only the Apple RAM, I added back the third-party RAM and I’ve been running Leopard flawlessly since.
    It seems the installation software, which meticulously checks the installer disk for flaws, should also check the RAM to see if the installation will be successful (i.e., check to see if it is going to produce the “essentials” error) and also check to see if you have enough valid RAM to install, before it begins installation, and to let the user know there will be a problem unless the RAM is changed to valid cards.
    I “assumed” I had enough valid RAM when I first tried to install Leopard because I had a G5, but it had only 256 MB of non-Apple brand RAM (minimum of 512 is required). A direct check of that by the installer and letting me know it was a problem would have saved me a lot of trouble checking lots of other potential problems, like a bad installer disk, a third-party drive, etc., before I figured out it was insufficient and incompatible RAM for the installation.
    I read the minimal requirements for installation of Leopard and probably someone will say I should have checked all those before I tried the installation, but I didn’t, as I’m sure many others have not, because we “assume” Apple had tested it and would prevent us from making any mistake like this.
    Previously Apple made their software and hardware to “just work” by providing error messages before we made an error and we have come to rely on that. But they overlooked this problem on this update. It’s the first time I’ve had a problem with an update from Apple.
    I’m still a loyal Apple user, but I’ll check requirements a little closer with future updates.

  • SCOM agent install fails Error 80070035 - the network path was not found

    I have deployed SCOM 2012 agents to most servers (2008, 2008 R2, 2012, 2012R2) in our estate but some either fail to install or are not monitored. I assume the two problems are related, but for now I am concentrating on the servers that fail completely.
    Installation is from the Discovery Wizard and I have about 20 servers that fail of various server versions.
    So looking at one specific server that is failing to install the agent - a 2008 standard service pack 2
    The firewall in on and file and printer sharing is enabled for domain, remote administration is enabled for domain
    I added a specific rule to allow TCP 5723 and 5724
    DCOM is enabled
    I can Ping the target server from the SCOM server by both name and FQDN - both return the same IP and our DNS server has only one entry for this server
    I can browse to the admin share \\server\C$ from the SCOM Server, using the same account that I specify for the agent install that is a domain admin with rights on this server (and on the other servers the agent
    did install to) and the server has plenty of disk space available
    I am not sure what else to look at so would welcome any ideas
    Thanks

    Hi Petro,
    I have a Agent installation failure cheat sheet, For your error 80070035 it is said to perform a manual installation.
    So i would like to understand which version of SCOM is this ? 2007 R2 or 2012 or 2012 r2 ?
    Also check if your agents have the WMI service started and enabled ?
    Also if yours is a SCOM 2007 R2 do you have a RMS & MS in your management group ? If yes then Pushing the agent installation from MS may cause such issue. So would suggest you push the installation from RMS.
    Also check if your Network connectivity meets the minimum requirement as recommended by SCOM. Below is applicable for Both SCOM 2007 R2 & SCOM 2012 & 2012 R2.
    Component A
    Component B
    Minimum Requirement
    Root management server or management server
    Agent
    64 Kbps
    Root management server or management server
    Agentless
    1024 Kbps
    Root management server or management server
    Database
    256 Kbps
    Also check if you have any Anti virus / Firewall which is blocking the install / communication. If yes disabe or add the "Monitoringhost.exe to the safe list or what your feature is.
    Check if you have another IP assigned to the NIC card and remove it tempraurly andchecl.
    Also post the event logs of the Agents which are in not monitored state for analysis.
    SCOM Agent installation failure error codes
    Error
    Error Code(s)
    Remediation Steps
    The MOM Server could not execute WMI Query "Select * from Win32_Environment where
    NAME='PROCESSOR_ARCHITECTURE'" on computer server.domain.com
    Operation: Agent Install
    Install account: domain\account
    Error Code: 80004005
    Error Description: Unspecified error
    80004005
    1.  Check the PATH environment variable.  If the PATH statement is very long, due to lots of installed third party software - this can
    fail.  Reduce the path by converting any long filename destinations to 8.3, and remove any path statements that are not necessary.
    2.  The cause
    could be corrupted Performance Counters on the target Agent.
    To rebuild all Performance counters including extensible and third party counters in Windows Server 2003, type the following commands at a command
    prompt. Press ENTER after each command.
    cd
    \windows\system32
    lodctr /R
    Note /R is uppercase.
    Windows Server 2003 rebuilds all the counters because it reads all the .ini files in the C:\Windows\inf\009 folder for the English operating system.
    How to manually rebuild Performance Counter Library values
    http://support.microsoft.com/kb/300956
    3.  Manual agent install. 
    The MOM Server could not execute WMI Query "Select * from Win32_OperatingSystem" on
    computer “servername.domain.com”
    Operation: Agent Install
    Install account: DOMAIN\account
    Error Code: 800706BA
    Error Description: The RPC server is unavailable.
    8004100A
    800706BA
    1.  Ensure agent push account has local admin rights
    2.  Firewall is blocking NetBIOS access
    3.  Inspect WMI health and rebuild repository if necessary
    4.  Firewall is blocking ICMP  (Live OneCare)
    5.  DNS incorrect
    The MOM Server failed to open service control manager on computer "servername.domain.com". Access is Denied
    Operation: Agent Install
    Install account: DomainName\User Account
    Error Code: 80070005
    Error Description: Access is denied.
    80070005
    80041002
    1.  Verify SCOM agent push account is in Local Administrators group on target computer.
    2.  On Domain controllers will have to work with AD team to install agent manually if agent push account is not a domain admin.
    Disable McAfee antivirus during push
    The MOM Server failed to open service control manager on computer "servername.domain.com".
    Therefore, the MOM Server cannot complete configuration of agent on the computer.
    Operation: Agent Install
    Install account: DOMAIN\account
    Error Code: 800706BA
    Error Description: The RPC server is unavailable.
    800706BA
    1.  Firewall blocking NetBIOS ports
    2.  DNS resolution issue.  Make sure the agent can ping the MS by NetBIOS and FQDN.  Make sure the MS can ping the agent by NetBIOS
    and FQDN
    3.  Firewall blocking ICMP
    4.  RPC services stopped.
    The MOM Server failed to acquire lock to remote computer servername.domain.com. This means there is already an agent management operation proceeding
    on this computer, please retry the Push Agent operation after some time.
    Operation: Agent Install
    Install account: DOMAIN\account
    Error Code: 80072971
    Error description: Unknown error 0x80072971
    80072971
    This problem occurs if the LockFileTime.txt file is located in the following folder on the remote computer:
    %windir%\422C3AB1-32E0-4411-BF66-A84FEEFCC8E2
    When you install or remove a management agent, the Operations Manager 2007 management server copies temporary files to the remote computer. One
    of these files is named LockFileTime.txt. This lock file is intended to prevent another management server from performing a management agent installation at the same time as the current installation. If the management agent installation is unsuccessful and
    if the management server loses connectivity with the remote computer, the temporary files may not be removed. Therefore, the LockFileTime.txt may remain in the folder on the remote computer. When the management server next tries to perform an agent installation,
    the management server detects the lock file. Therefore, the management agent installation is unsuccessful.
    http://support.microsoft.com/kb/934760/en-us
    The MOM Server detected that the following services on computer "(null);NetLogon" are not running. These services are required for push
    agent installation. To complete this operation, either start the required services on the computer or install the MOM agent manually by using MOMAgent.msi located on the product CD.
    Operation: Agent Install
    Remote Computer Name: servername.domain.com Install account: DOMAIN\account
    Error Code: C000296E
    Error Description: Unknown error 0xC000296E
    C000296E
    1.  Netlogon service is not running.  It must be set to auto/started
    The MOM Server detected that the following services on computer
    "winmgmt;(null)" are not running
    C000296E
    1.  WMI services not running or WMI corrupt
    The MOM Server detected that the Windows Installer service (MSIServer) is disabled on computer "servername.domain.com". This service is
    required for push agent installation. To complete this operation on the computer, either set the MSIServer startup type to "Manual" or "Automatic", or install the MOM agent manually by using MOMAgent.msi located on the product CD.
    Operation: Agent Install
    Install account: DOMAIN\account
    Error Code: C0002976
    Error Description: Unknown error 0xC0002976
    C0002976
    1.  Windows Installer service is not running or set to disabled – set this to manual or auto and start it.
    The Agent Management Operation Agent Install failed for remote computer servername.domain.com.
    Install account: DOMAIN\account
    Error Code: 80070643
    Error Description: Fatal error during installation.
    Microsoft Installer Error Description:
    For more information, see Windows Installer log file "C:\Program Files\System Center Operations Manager 2007\AgentManagement\AgentLogs\servernameAgentInstall.LOG
    C:\Program Files\System Center Operations Manager 2007\AgentManagement\AgentLogs\servernameMOMAgentMgmt.log" on the Management Server.
    80070643
    1.  Enable the automatic Updates service…. Install the agent – then disable the auto-updates service if desired.
    Call was canceled by the message filter
    80010002
    Install latest SP and retry. One server that failed did not have Service pack installed
    The MOM Server could not find directory \\I.P.\C$\WINDOWS\. Agent will not be installed on computer "name". Please verify the required
    share exists.
    80070006
    1.  Manual agent install
    Possible locking on registry?
    http://www.sysadmintales.com/category/operations-manager/
    Try manual install.
    Verified share does not exist.
    The network path was not found.
    80070035
    1.  Manual agent install
    The Agent Management Operation Agent Install failed for remote computer "name". There is not enough space on the disk.
    80070070
    1.  Free space on install disk
    The MOM Server failed to perform specified operation on computer "name". The semaphore timeout period has expired.
    80070079
    NSlookup failed on server. Possible DNS resolution issue.
    Try adding dnsname to dnssuffix search list.
    The MOM Server could not start the MOMAgentInstaller service on computer "name" in the time.
    8007041D
    80070102
    NSlookup failed on server. Possible DNS resolution issue.
    Verify domain is in suffix search list on management servers.
    The Agent Management Operation Agent Install failed for remote computer "name"
    80070643
    1.  Ensure automatic updates service is started
    2.  Rebuild WMI repository
    3.  DNS resolution issue
    The Agent Management Operation Agent Install failed for remote computer "name". Another installation is already in progress.
    80070652
    Verify not in pending management. If yes, remove and then attempt installation again.
    The MOM Server detected that computer "name" has an unsupported operating system or service pack version
    80072977
    Install latest SP and verify you are installing to Windows system.
    Not discovered
    Agent machine is not a member of domain
    Ping fails
    1.  Server is down
    2.  Server is blocked by firewall
    3.  DNS resolving to wrong IP.
    Fail to resolve machine
    1.  DNS issue
    The MOM Server failed to perform specified operation on computer "name". Not enough server storage…
    8007046A
    1.  This is typically a memory error caused by the remote OS that the agent is being installed on.
    There are currently no logon servers available to service the logon request.
    8007051F
    1.  Possible DNS issue
    This installation package cannot be installed by the Windows Installer service. You must install a Windows service pack that contains a newer version
    of the Windows Installer service.
    8007064D
    1.  Install Windows Installer 3.1
    The network address is invalid
    800706AB
    Possible DNS name resolution issue.
    Tried nslookup on server name and did not get response.
    Verify domain is in suffix search list on management servers.
    The MOM Server failed to perform specified operation on computer servername.domain.com
    80070040
    1.  Ensure agent push account has local admin rights
    The MOM Server detected that the actual NetBIOS name SERVERNAME is not same as the given NetBIOS name provide for remote computer SERVERNAME.domain.com.
    80072979
    1.  Correct DNS/WINS issue.
    2.  Try pushing to NetBIOS name
    Gautam.75801

  • ITunes 10.6.1 install failed

    The system attempted to automatically update iTunes recently. It failed. I was busy at the time so I didn't really pay any attention to it. Fast forward a few days to now. When I launch iTunes, I am told "This copy of iTunes is corrupted or is not installed correctly. Please reinstall iTunes." I tried to do just that. I downloaded the 10.6.1 installer from Apple and attempted to install it. Again, the installation failed. Below are the Console messages. How do I correct this problem? I have already repaired disk permissions, verified the disk, and rebooted. The most notable things I did recently were:
    1) Updated Xcode from the App Store app. When the download and update completed, I accidentally hit the update all button in the App Store app again causing Xcode to start downloading. I immediately paused the download. The paused download disappeared from the App Store app's available updates list but it did appear in Launchpad. I tried to delete paused download from Launchpad and it didn't appear to work but somehow, it is now nowhere to be found in Launchpad.
    2) Streamed videos from my MacBook to my new Apple TV. Incidentally, the Apple TV malfunctioned (all icons but Computers and Settings were displayed) and I had to reset it to factory defaults. It works again.
    3/30/12 11:27:06.200 PM Installer: iTunes  Installation Log
    3/30/12 11:27:06.200 PM Installer: Opened from: /Volumes/iTunes 10.6.1/Install iTunes.pkg
    3/30/12 11:27:06.453 PM Installer: Performance: Please update this scripting addition to supply a value for ThreadSafe for each event handler: "/Library/ScriptingAdditions/SIMBL.osax"
    3/30/12 11:27:08.509 PM Installer: InstallerStatusNotifications plugin loaded
    3/30/12 11:27:19.290 PM Installer: ================================================================================
    3/30/12 11:27:19.290 PM Installer: User picked Standard Install
    3/30/12 11:27:19.290 PM Installer: Choices selected for installation:
    3/30/12 11:27:19.290 PM Installer:           Upgrade: "iTunes"
    3/30/12 11:27:19.290 PM Installer:           Upgrade: "Apple Mobile Device Support"
    3/30/12 11:27:19.290 PM Installer:           Upgrade: "iTunes"
    3/30/12 11:27:19.290 PM Installer: ================================================================================
    3/30/12 11:27:24.120 PM Installer: Configuring volume "Lion"
    3/30/12 11:27:24.133 PM Installer: Free space on "Lion": 170.99 GB (170993594368 bytes).
    3/30/12 11:27:24.133 PM Installer: Create temporary directory "/var/folders/63/fs0yw4ld62xdpyp0ysk7jcd00000gn/T//Install.560hqV9Ph"
    3/30/12 11:27:24.139 PM Installer: IFPKInstallElement (5 packages)
    3/30/12 11:27:24.315 PM authorizationhost: SFBuiltinEntitled: Installer.app is not entitled for system.install.apple-software
    3/30/12 11:27:24.342 PM authorizationhost: SFBuiltinEntitled: Installer.app is not entitled for system.install.app-store-software
    3/30/12 11:27:24.369 PM authorizationhost: SFBuiltinEntitled: Installer.app is not entitled for system.install.app-store-software
    3/30/12 11:27:24.370 PM com.apple.SecurityServer: Failed to authorize right 'system.install.app-store-software' by client '/System/Library/PrivateFrameworks/PackageKit.framework/Versions/A/Resources/installd' [568] for authorization created by '/System/Library/CoreServices/Installer.app' [560]
    3/30/12 11:27:24.373 PM installd: PackageKit: ----- Begin install -----
    3/30/12 11:27:48.648 PM xpchelper: could not open dyld map file: (null)
    3/30/12 11:27:50.142 PM sudo:     root : TTY=unknown ; PWD=/private/tmp/PKInstallSandbox.MNraFl/Scripts/com.apple.pkg.AppleMobileDeviceSupport.yxOS2Q ; USER=root ; COMMAND=/bin/launchctl unload //System/Library/LaunchDaemons/com.apple.usbmuxd.plist
    3/30/12 11:27:50.000 PM kernel: Kext com.apple.driver.AppleMobileDevice not found for unload request.
    3/30/12 11:27:50.000 PM kernel: Kext com.apple.driver.AppleUSBEthernetHost not found for unload request.
    3/30/12 11:27:54.582 PM shove: [source=file] failed _RelinkFile(/var/folders/zz/zyxvpxvq6csfxvn_n0000000000000/Cleanup At Startup/PKInstallSandbox-tmp/Root/Applications/iTunes.app/Contents/Resources/Spanish.lproj/CDInfo.nib/keyedobjects.nib, /Applications/iTunes.app/Contents/Resources/Spanish.lproj/CDInfo.nib/keyedobjects.nib): Operation not permitted
    3/30/12 11:27:54.585 PM shove: srcPath = /var/folders/zz/zyxvpxvq6csfxvn_n0000000000000/Cleanup At Startup/PKInstallSandbox-tmp/Root/Applications/iTunes.app/Contents/Resources/Spanish.lproj/CDInfo.nib/keyedobjects.nib NSFileOwnerAccountID=0 NSFileHFSTypeCode=0 NSFileSystemFileNumber=7909127 NSFileExtensionHidden=0 NSFileSystemNumber=234881028 NSFileSize=12863 NSFileGroupOwnerAccountID=0 NSFileOwnerAccountName=root NSFileCreationDate=2012-03-21 07:31:07 +0000 NSFilePosixPermissions=420 NSFileHFSCreatorCode=0 NSFileType=NSFileTypeRegular NSFileGroupOwnerAccountName=wheel NSFileReferenceCount=1 NSFileModificationDate=2012-03-21 07:31:07 +0000
    3/30/12 11:27:54.586 PM shove: dstPath = /Applications/iTunes.app/Contents/Resources/Spanish.lproj/CDInfo.nib/keyedobjects.nib NSFileOwnerAccountID=0 NSFileHFSTypeCode=0 NSFileSystemFileNumber=6522007 NSFileExtensionHidden=0 NSFileSystemNumber=234881028 NSFileSize=12863 NSFileGroupOwnerAccountID=0 NSFileOwnerAccountName=root NSFileCreationDate=2012-03-07 06:13:35 +0000 NSFilePosixPermissions=420 NSFileHFSCreatorCode=0 NSFileType=NSFileTypeRegular NSFileGroupOwnerAccountName=wheel NSFileReferenceCount=1 NSFileModificationDate=2012-03-07 06:13:35 +0000
    3/30/12 11:27:54.587 PM shove: dstParentPath = /Applications/iTunes.app/Contents/Resources/Spanish.lproj/CDInfo.nib NSFileOwnerAccountID=0 NSFileSystemFileNumber=1255061 NSFileExtensionHidden=0 NSFileSystemNumber=234881028 NSFileSize=2270062258 NSFileGroupOwnerAccountID=0 NSFileOwnerAccountName=root NSFileCreationDate=1972-02-24 19:55:33 +0000 NSFilePosixPermissions=493 NSFileAppendOnly=1 NSFileType=NSFileTypeDirectory NSFileGroupOwnerAccountName=wheel NSFileReferenceCount=50889 NSFileModificationDate=1970-01-10 05:55:04 +0000 NSFileImmutable=1 XATTR=com.apple.FinderInfo
    3/30/12 11:27:54.587 PM com.apple.installd: Operation not permitted
    3/30/12 11:27:55.044 PM installd: PackageKit: Install Failed: Error Domain=PKInstallErrorDomain Code=120 "An unexpected error occurred while moving files to the final destination." UserInfo=0x7fb87b913c20 {NSLocalizedDescription=An unexpected error occurred while moving files to the final destination., arguments=(
        "-f",
        "-s",
        "/var/folders/zz/zyxvpxvq6csfxvn_n0000000000000/Cleanup At Startup/PKInstallSandbox-tmp/Root",
    ), NSUnderlyingError=0x7fb87b914c80 "The operation couldn’t be completed. Operation not permitted"} {
        NSLocalizedDescription = "An unexpected error occurred while moving files to the final destination.";
        NSUnderlyingError = "Error Domain=NSPOSIXErrorDomain Code=1 \"The operation couldn\U2019t be completed. Operation not permitted\"";
        arguments =     (
            "-f",
            "-s",
            "/var/folders/zz/zyxvpxvq6csfxvn_n0000000000000/Cleanup At Startup/PKInstallSandbox-tmp/Root",
    3/30/12 11:27:55.415 PM Installer: Install failed: The Installer encountered an error that caused the installation to fail. Contact the software manufacturer for assistance.
    3/30/12 11:27:55.571 PM Installer: IFDInstallController AD3348B0 state = 7
    3/30/12 11:27:55.571 PM Installer: Displaying 'Install Failed' UI.
    3/30/12 11:27:55.573 PM Installer: 'Install Failed' UI displayed message:'The Installer encountered an error that caused the installation to fail. Contact the software manufacturer for assistance.'.
    3/30/12 11:27:55.588 PM Installer: The Installer encountered an error that caused the installation to fail. Contact the software manufacturer for assistance.

    This problem is resolved. I deleted the old iTunes (with write permissions turned on for my account) and reinstalled successfully. Removing the deleted iTunes from Trash was troublesome even with root but after playing around with permissions and flags, I was able to remove it.

  • _10.7 push install failed, and fubar'd everything

    Just got a push notice to update to 10.7 (from 10.6.??).  I acked the message, and after a zillion minutes, got an error message that the install failed, and that I need to do download only and manually install.  So, I tried that.  Failed with-- "The installer as encountered an unexpected error installing this package.  This may indicate a problem with this package.  The error code is 2324."  So, I tried uninstall, presumably of the 10.6.?? that's been on the machine for a while, and has been working.  Uninstall fails with same error as above.  So... I downloaded 10.7 and tried to install ON TOP OF current, still working install.  Same permission error, and now, whatever munged version is actually on the machine (the previously working 10.6, 10.7, or some amalgam of the two) gives me the following error when I attempt to run it-- "The item referred to by this shortcut cannot be accessed. You may not have the appropriate permissions."  If I Explorer to %ProgramFiles(x86)%\iTunes, I get "... is not accessible. Access is denied."  I CAN access %ProgramFiles%\iTunes (the 64 bit folder), and there are files... but nothing executable... just a resource folder and a handful of dll's. 
    I am admin on the machine (actually, I am the ONLY human account on the machine... only others are typical system service accounts).  Machine is WIN7 Premium, SP1.  It is very stable, has no recent (in the last month or so) changes, except a hanful of Windows Update patched from last week. 
    Suggestions on how to get the machine out of this "iTunes is broken, but can't uninstall/install to fix it" loop??? 
    Grrrrrr.

    Community support seems to be slow moving .  Others not having this problem?
    I spent 4 hours culling through registry, killing off any keys that remotely resembled "apple" or "itunes," manually deleted program files, and then forced msiexec to unregister the GUID, mixed in with a zillion reboots, and was able to install 10.7 clean.  BTW, SAME problem on second machine... so it is highly unlikely this is "a Windows problem."  Apple, please check your installer package... methinks it'd fubar.

  • Install failed with exit code 11?

    Hi,
    I am trying to deploy a language pack and set the override language to English-US which I have created 2 programs for in my package. When the first program runs I am getting an error in the execmgr.log that "Install failed with exit code 11" Any
    ideas what this means? When I run this command manually on the machine it works fine:
    "C:\WINDOWS\System32\Dism.exe" /online /add-package /packagepath:"en-us\lp.cab"
    I checked the dism.log as well but I don't see any errors. Both logs are below, any help or suggestions would be greatly appreciated TIA
    <![LOG[Command line = "C:\WINDOWS\System32\Dism.exe" /online /add-package /packagepath:"en-us\lp.cab", Working Directory = C:\WINDOWS\ccmcache\4j\]LOG]!><time="08:00:28.447+300" date="01-27-2015" component="execmgr"
    context="" type="1" thread="4976" file="scriptexecution.cpp:352">
    <![LOG[Running "C:\WINDOWS\System32\Dism.exe" /online /add-package /packagepath:"en-us\lp.cab" with 32bitLauncher]LOG]!><time="08:00:28.447+300" date="01-27-2015" component="execmgr" context=""
    type="1" thread="4976" file="scriptexecution.cpp:370">
    <![LOG[Created Process for the passed command line]LOG]!><time="08:00:28.509+300" date="01-27-2015" component="execmgr" context="" type="1" thread="4976" file="scriptexecution.cpp:513">
    <![LOG[Raising event:
    [SMS_CodePage(437), SMS_LocaleID(1033)]
    instance of SoftDistProgramStartedEvent
     AdvertisementId = "LIA20115";
     ClientID = "GUID:428D91E4-84BD-4740-97D9-9177C39FA3F0";
     CommandLine = "\"C:\\WINDOWS\\System32\\Dism.exe\" /online /add-package /packagepath:\"en-us\\lp.cab\"";
     DateTime = "20150127130028.509000+000";
     MachineName = "";
     PackageName = "";
     ProcessID = 2012;
     ProgramName = "Install";
     SiteCode = "";
     ThreadID = 4976;
     UserContext = "NT AUTHORITY\\SYSTEM";
     WorkingDirectory = "C:\\WINDOWS\\ccmcache\\4j\\";
    ]LOG]!><time="08:00:28.509+300" date="01-27-2015" component="execmgr" context="" type="1" thread="4976" file="event.cpp:715">
    <![LOG[Raised Program Started Event for Ad:LIA20115, Package:LIA002A0, Program: Install]LOG]!><time="08:00:28.509+300" date="01-27-2015" component="execmgr" context="" type="1" thread="4976"
    file="executioncontext.cpp:459">
    <![LOG[Raising client SDK event for class CCM_Program, instance CCM_Program.PackageID="LIA002A0",ProgramID="Install", actionType 1l, value NULL, user NULL, session 4294967295l, level 0l, verbosity 30l]LOG]!><time="08:00:28.509+300"
    date="01-27-2015" component="execmgr" context="" type="1" thread="4976" file="event.cpp:405">
    <![LOG[Raising client SDK event for class CCM_Program, instance CCM_Program.PackageID="LIA002A0",ProgramID="Install", actionType 1l, value , user NULL, session 4294967295l, level 0l, verbosity 30l]LOG]!><time="08:00:28.509+300"
    date="01-27-2015" component="execmgr" context="" type="1" thread="4976" file="event.cpp:405">
    <![LOG[MTC task with id {B7EEE891-740D-4762-8D2B-BA2D7E351F1D}, changed state from 4 to 5]LOG]!><time="08:00:28.525+300" date="01-27-2015" component="execmgr" context="" type="1" thread="5904"
    file="execreqmgr.cpp:6288">
    <![LOG[Program exit code 11]LOG]!><time="08:00:28.650+300" date="01-27-2015" component="execmgr" context="" type="1" thread="2488" file="scriptexecution.cpp:676">
    <![LOG[Looking for MIF file to get program status]LOG]!><time="08:00:28.650+300" date="01-27-2015" component="execmgr" context="" type="1" thread="2488" file="executionstatus.cpp:282">
    <![LOG[Script for Package:LIA002A0, Program: Install failed with exit code 11]LOG]!><time="08:00:28.650+300" date="01-27-2015" component="execmgr" context="" type="3" thread="2488" file="executionstatus.cpp:252">
    <![LOG[Raising event:
    [SMS_CodePage(437), SMS_LocaleID(1033)]
    instance of SoftDistProgramErrorEvent
     AdvertisementId = "LIA20115";
     ClientID = "GUID:428D91E4-84BD-4740-97D9-9177C39FA3F0";
     DateTime = "20150127130028.650000+000";
     ExitCode = "11";
     MachineName = "";
     PackageName = "LIA002A0";
     ProcessID = 2012;
     ProgramName = "Install";
     SiteCode = "";
     ThreadID = 2488;
     UserContext = "NT AUTHORITY\\SYSTEM";
    ]LOG]!><time="08:00:28.650+300" date="01-27-2015" component="execmgr" context="" type="1" thread="2488" file="event.cpp:715">
    <![LOG[Raised Program Error Event for Ad:LIA20115, Package:LIA002A0, Program: Install]LOG]!><time="08:00:28.650+300" date="01-27-2015" component="execmgr" context="" type="1" thread="2488"
    file="executioncontext.cpp:572">
    <![LOG[Execution is complete for program Install. The exit code is 11, the execution status is FailureNonRetry]LOG]!><time="08:00:28.665+300" date="01-27-2015" component="execmgr" context="" type="1"
    thread="1956" file="execreqmgr.cpp:4165">
    <![LOG[Requesting MTC to delete task with id: {B7EEE891-740D-4762-8D2B-BA2D7E351F1D}]LOG]!><time="08:00:28.681+300" date="01-27-2015" component="execmgr" context="" type="1" thread="1956"
    file="executionrequest.cpp:9041">
    <![LOG[MTC task with id: {B7EEE891-740D-4762-8D2B-BA2D7E351F1D} deleted successfully.]LOG]!><time="08:00:28.681+300" date="01-27-2015" component="execmgr" context="" type="1" thread="1956"
    file="executionrequest.cpp:9070">
    <![LOG[Raising client SDK event for class CCM_Program, instance CCM_Program.PackageID="LIA002A0",ProgramID="InstallEN", actionType 10l, value Result:FALSE, user NULL, session 4294967295l, level 0l, verbosity 30l]LOG]!><time="08:00:28.697+300"
    date="01-27-2015" component="execmgr" context="" type="1" thread="1956" file="event.cpp:405">
    <![LOG[Deleting request for program Install. Failing parent program InstallEN]LOG]!><time="08:00:28.697+300" date="01-27-2015" component="execmgr" context="" type="1" thread="1956" file="execreqmgr.cpp:8147">
    <![LOG[Requesting MTC to delete task with id: ]LOG]!><time="08:00:28.697+300" date="01-27-2015" component="execmgr" context="" type="1" thread="1956" file="executionrequest.cpp:9041">
    <![LOG[This execution request does not have a corresponding task in MTC.]LOG]!><time="08:00:28.697+300" date="01-27-2015" component="execmgr" context="" type="1" thread="1956" file="executionrequest.cpp:9059">
    <![LOG[Requesting MTC to delete task with id: {B7EEE891-740D-4762-8D2B-BA2D7E351F1D}]LOG]!><time="08:00:28.697+300" date="01-27-2015" component="execmgr" context="" type="1" thread="1956"
    file="executionrequest.cpp:9041">
    <![LOG[This execution request does not have a corresponding task in MTC.]LOG]!><time="08:00:28.697+300" date="01-27-2015" component="execmgr" context="" type="1" thread="1956" file="executionrequest.cpp:9059">
    <![LOG[Raising client SDK event for class CCM_Program, instance CCM_Program.PackageID="LIA002A0",ProgramID="Install", actionType 1l, value , user NULL, session 4294967295l, level 0l, verbosity 30l]LOG]!><time="08:00:28.697+300"
    date="01-27-2015" component="execmgr" context="" type="1" thread="1956" file="event.cpp:405">
    015-01-27 08:00:28, Info                  DISM   DISM.EXE:
    2015-01-27 08:00:28, Info                  DISM   DISM.EXE: <----- Starting Dism.exe session ----->
    2015-01-27 08:00:28, Info                  DISM   DISM.EXE:
    2015-01-27 08:00:28, Info                  DISM   DISM.EXE: Host machine information: OS Version=6.3.9600, Running architecture=x86, Number of processors=4
    2015-01-27 08:00:28, Info                  DISM   DISM.EXE: Dism.exe version: 6.3.9600.16384
    2015-01-27 08:00:28, Info                  DISM   DISM.EXE: Executing command line: "C:\WINDOWS\System32\Dism.exe" /online /add-package /packagepath:"en-us\lp.cab"
    2015-01-27 08:00:28, Info                  DISM   DISM Provider Store: PID=5984 TID=4336 Getting Provider FolderManager - CDISMProviderStore::GetProvider
    2015-01-27 08:00:28, Info                  DISM   DISM Provider Store: PID=5984 TID=4336 Provider has not previously been encountered.  Attempting to initialize
    the provider. - CDISMProviderStore::Internal_GetProvider
    2015-01-27 08:00:28, Info                  DISM   DISM Provider Store: PID=5984 TID=4336 Loading Provider from location C:\WINDOWS\System32\Dism\FolderProvider.dll
    - CDISMProviderStore::Internal_GetProvider
    2015-01-27 08:00:28, Info                  DISM   DISM Provider Store: PID=5984 TID=4336 Connecting to the provider located at C:\WINDOWS\System32\Dism\FolderProvider.dll.
    - CDISMProviderStore::Internal_LoadProvider
    2015-01-27 08:00:28, Info                  DISM   DISM.EXE: Image session has been closed. Reboot required=no.
    2015-01-27 08:00:28, Info                  DISM   DISM.EXE:
    2015-01-27 08:00:28, Info                  DISM   DISM.EXE: <----- Ending Dism.exe session ----->
    2015-01-27 08:00:28, Info                  DISM   DISM.EXE:

    Thanks, it seems as though it is not doing anything now. I just see that the policy has arrived in the log below but it is not installing it? The dism.log hasn't changed at all so it seems that it isn't even executing the command now? Am I missing something
    else? I even tried re-advertising it though client center.
    Command is now:
    C:\WINDOWS\sysnative\Dism.exe  /online /add-package /packagepath:"en-us\lp.cab"
    <![LOG[Raising client SDK event for class CCM_Program, instance CCM_Program.PackageID="LIA002A0",ProgramID="InstallEN", actionType 45l, value NULL, user NULL, session 4294967295l, level 0l, verbosity 30l]LOG]!><time="08:52:28.943+300"
    date="01-27-2015" component="execmgr" context="" type="1" thread="5036" file="event.cpp:405">
    <![LOG[Policy arrived for child program Install]LOG]!><time="09:12:48.440+300" date="01-27-2015" component="execmgr" context="" type="1" thread="3528" file="execreqmgr.cpp:6867">
    <![LOG[Policy arrived for parent package LIA002A0 program InstallEN]LOG]!><time="09:12:48.487+300" date="01-27-2015" component="execmgr" context="" type="1" thread="3528" file="execreqmgr.cpp:6893">
    <![LOG[Raising client SDK event for class CCM_Program, instance CCM_Program.PackageID="LIA002A0",ProgramID="InstallEN", actionType 6l, value NULL, user NULL, session 4294967295l, level 0l, verbosity 30l]LOG]!><time="09:12:48.487+300"
    date="01-27-2015" component="execmgr" context="" type="1" thread="3528" file="event.cpp:405">
    <![LOG[Raising event:
    [SMS_CodePage(437), SMS_LocaleID(1033)]
    instance of SoftDistProgramOfferReceivedEvent
     AdvertisementId = "LIA20116";
     ClientID = "GUID:428D91E4-84BD-4740-97D9-9177C39FA3F0";
     DateTime = "20150127141248.502000+000";
     MachineName = "";
     ProcessID = 2012;
     SiteCode = "";
     ThreadID = 3528;
    ]LOG]!><time="09:12:48.502+300" date="01-27-2015" component="execmgr" context="" type="1" thread="3528" file="event.cpp:715">
    <![LOG[The user has logged off.]LOG]!><time="09:36:59.174+300" date="01-27-2015" component="execmgr" context="" type="1" thread="4320" file="execreqmgr.cpp:5138">

  • The desktop on which I had Lightroom and PhotoshopCC installed failed and I no longer have access to it. How do I deactivate the software on those machines so that I can reinstall it on my new Mac?

    Question: The desktop on which I had Lightroom and PhotoshopCC installed failed and I no longer have access to it. How do I deactivate the software on those machines so that I can reinstall it on my new Mac?

    Absolutely - but I had no idea there were two versions. When I got my new laptop I just went to the Adobe site to download and install LR5. It never asked if I had a license; it just directed me to install CC to start a trial which I thought I could license after downloading. Several sessions and many hours of looking through the forums and Google for an answer I never ran across anything that made this distinction. I still haven't found a path from www.adobe.com that would get me to the standalone download page (it's probably there, wasn't obvious to me) and looking at the download page it doesn't make any CC/standalone distinction.
    There are many places I could have gotten a hint - for instance the license could be tagged "stand alone edition", the CC-version could recognize the stand-alone key and either accept it or produce a more meaningful error message, or the download site or the CC app could ask if I had previously purchased a key, etc.
    It was my error to assume this was a deactivation problem, but it looked the same as a previous deactivation problem with Photoshop.
    In any event, thank you for your help.

  • Final cut studio 2 install failed?

    I just bought a new final cut studio 2 and i put in the install disc, Than it said to put in the audio content 1 disc so i did. And than it said put in the final cut studio disck (Which i presume is the install disc) So i did than it said the install failed cause my source media was damaged? Anybody know how to fix this?
    P.S I already tried cleaning the disc. No luck

    I can't remember starting with an audio content disc during FCS2 setup.
    From what you describe it sounds like an installation disc problem.
    Contact your local Apple Store for their advice.
    Al

Maybe you are looking for