GSR 12000 Router and Router 7609S

Hi all,
GSR 12816 supports 40GB/slot. How can I check this information ?
I tried to using Dynamic Configuration Tool to build 04 SPA-1X10GE-L-V2 on 12000-SIP-601 but It does not support.
Please answer as soon as possible.
Thanks

Oh, I checked again. The problem has been solved.
tks.

Similar Messages

We have router 7609s,so we need to know,router RAM,so how it will get i have show tech-support configuration.can you tell me pls

how will get ram of router 7609s and 7206 ,can you tell whats bydefault RAM of both routers,please give me response ASAP.

Hello
Do you want to know how much RAM you have in 7600, Show version command can be use to find it
Cisco 7206VXR (NPE400) processor (revision A) with 245760K/16384K bytes of memory.
Above router has 245760K+16384K/1024 = 256MB of RAM.
Thanks
Kunal

When i drag and drop to my ipod it wants to sync everything, but if i make changes to the syncing options and apply it wants to sync it all to make it work. i have 12000 songs and takes two days to sync everything. is there an easier way to drag and drop

when i drag and drop to my ipod it wants to sync everything, but if i make changes to the syncing options and apply it wants to sync it all to make it work. i have 12000 songs and takes two days to sync everything. is there an easier way to drag and drop just one album without making settings changes?

The first ever Sync of 12,000 songs to an empty iPod will take a while, but it shouldn't take two days.
Once all 12,000 songs have been Synced to the iPod, subsequent changes to just one album will result in a very short Sync time. That Sync will include:
the change to that one album
play counts on iPod updated into your iTunes Library
Smart Playlists updated: some complex Smart Playlists are not always updated by the iPod but have to wait for a Sync with the Library.
housework - in other words, behind the scenes tasks that we don't need to see.
Those subsequent Syncs do not sync every single song every time.
So, stick with Syncing. If the first Sync of all your songs is taking too long, try syncing part of the Library (say one or two genres) the first time, a further part the second time and so on. After all, with a Library that large, manually managing the iPod will be a source of torture.

Load distribution not so even for multicast traffic (ECMP) between a GSR 12410 (XR) and a CRS-1 router

Hi,
I have a scenario in which I see the multicast S,G streams are distributed not so even in the 3 interfaces between a GSR 12404 (XR 3.8.4) and a CRS1 (XR 3.6.2). The multicast mode is SSM.
The total S,G (sources and multicast groups) are 82.
The topology is as follows:
                                               ---link 1--------
Multicast sources ----- CRS1 ---link 2-------- GSR12404------- Receivers
                                                ---link 3--------
From the total of 82 S,G coming from multicast sources, I see the following S,G distribution between the three links:
Link 1: 37 S,G
Link 2: 21 S,G
Link 3: 24 S,G
The big question is why the Link 1 has very different number of S,G compared to link 2 and link 3?
Multipath is enabled on both links. I copy the multicast configuration of CRS and GSR that is the same:
multicast-routing
address-family ipv4
interface GigabitEthernet0/2/0/0
   enable
interface GigabitEthernet0/2/1/1
   enable
interface GigabitEthernet0/2/1/2
   enable
nsf
multipath
ssm range SSM
Thanks,
Carlos.

Hi Agherardi,
Did you try to disable your firewall and refer the following KB to confirm you have choose the correct Affinity and Load-Balancing Behavior of the Custom Port Rule.
Specifying the Affinity and Load-Balancing Behavior of the Custom Port Rule
https://technet.microsoft.com/en-us/library/cc759039(v=ws.10).aspx
More information:
Using NLB
https://technet.microsoft.com/en-us/library/bb687542.aspx
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

RSVP graceful restart support in 12000 router

Hi,
It seems like the router is not supporting graceful restart full mode.
If you have to GSR's that are connected to each other, will it be possible to setup graceful restart and work together with SSO?
I have tried but with no success, if it's should work, have somebody any config example?
/Niklas

Thanks,
I will contact our sales.
Means helper-mode that the router can help the other side to recover a RP failure situation?
The other router must also support full-mode?
BR Niklas

IOS XR

Hello:
Which Cisco router platforms use IOS XR?
Is it just the CRS-1, ASR 9000 and GSR 12000? What about the asr 1000?
What is the big difference between regular IOS and IOS XR?
What is the ASR 9000 used for? WAN edge? SP PE? SP core?
So for so many questions...
Thanks

Hello Joe,
IOS XR is supported on CRS and GSR 12000 XR and ASR 9000
see
http://www.cisco.com/en/US/products/ps5845/products_installation_and_configuration_guides_list.html
about different IOS flavors:
http://www.cisco.com/en/US/products/ps6350/products_white_paper09186a0080b1351e.shtml
ASR 1000 supports IOS XE and Nexus supports NX-OS
IOS XR has a different architecture then IOS: it uses a real-time microkernel OS that provides basic services.
Over this common layer other SW layers are added for example OSPF or ISIS module, MPLS module and so on.
It is not a monolithic image, but rather it has a unix derived approach. Modularity provides also for the capability to perform partial updates of one or more SW modules. They are called SMU.
IOS XR is designed with service provider carrier class needs
ASR 9000 is designed for PE role and aggregation services and it is a young platform.
http://www.cisco.com/en/US/prod/collateral/routers/ps9853/data_sheet_c78-501767.html
to be noted also an ASR 14000 has been introduced recently but I cannot find info about it.
Hope to help
Giuseppe

About maximum ipv4 routes for GSR router

Hi all,
I am planning to install GSR 12404 router for Internet router to receive full BGP routing table. Just wondering what the maximum routes supported for GSR into the CEF?
The hardware will be used is as below
PRP-2
SIP-400 w/ SPA-2x1GE
Thanks,

looshfoo wrote:thinking about it, could it be the dhcp lease on the local router going up and it running a dhcp request and getting the route again?
Yes.
Your lease is only valid for X minutes/hours, after that it has to be renewed, which will recreate the def route. There's probably a config option in your dhcp client to ignore the def route.

Full internet routing in an internet MPLS VPN

Is it possible and advisable to run the full internet routing table in a seperate MPLS VRF. A default route is not an option
With kind regards,
Mike

Hi,
It is not advisable to have full Internet Routing table in a vrf.It is possible that you may run out of memory since different routers have different vrf routes holding capacity.e.g if you are using 12000 series and you have only one vrf configured then you can hold the entire Internet routing table in one vrf.
Which router you have ? Is it 12000 ?How many vrfs you have ? How many routes have you per vrf ?
You need to consider the above questions before making the decision.
-Waris

%ROUTING-RIB-3-UPDATE_TIMEOUT

Hi,
We are having GSR-12010 router in our n/w.Problm is that everytime any ospf link is going down we ae geting the error message listed below:
LC/0/2/CPU0:Jan 20 07:57:32 : ifmgr[164]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface POS0/2/3/0, changed state to Down
RP/0/8/CPU0:Jan 20 07:57:32 : ospf[304]: %ROUTING-OSPF-5-ADJCHG : Process 200, Nbr 10.181.128.3 on POS0/2/3/0 in area 0 from FULL to DOWN, Neighbor Down: interface down or detached
LC/0/2/CPU0:Jan 20 07:57:34 : g_spa_3[158]: %L2-SONET_LOCAL-4-ALARM : SonetPath0/2/3/0: B3_TCA
LC/0/2/CPU0:Jan 20 07:57:42 : ifmgr[164]: %PKT_INFRA-LINK-3-UPDOWN : Interface POS0/2/3/0, changed state to Up
LC/0/2/CPU0:Jan 20 07:57:42 : ifmgr[164]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface POS0/2/3/0, changed state to Up
LC/0/2/CPU0:Jan 20 07:57:45 : g_spa_3[158]: %L2-SONET_LOCAL-4-ALARM : SonetPath0/2/3/0: B3_TCA cleared
RP/0/8/CPU0:Jan 20 07:57:52 : ospf[304]: %ROUTING-OSPF-5-ADJCHG : Process 200, Nbr 10.181.128.3 on POS0/2/3/0 in area 0 from LOADING to FULL, Loading Done
RP/0/8/CPU0:Jan 20 08:27:32 : ipv4_rib[225]: %ROUTING-RIB-3-UPDATE_TIMEOUT : Client "ospf" updated the RIB without signaling update completion for Vrf: "default" Tbl: "default" Safi: "Unicast"
LC/0/2/CPU0:Jan 20 08:56:40 : ifmgr[164]: %PKT_INFRA-LINK-3-UPDOWN : Interface POS0/2/3/0, changed state to Down
LC/0/2/CPU0:Jan 20 08:56:40 : ifmgr[164]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface POS0/2/3/0, changed state to Down
RP/0/8/CPU0:Jan 20 08:56:40 : ospf[304]: %ROUTING-OSPF-5-ADJCHG : Process 200, Nbr 10.181.128.3 on POS0/2/3/0 in area 0 from FULL to DOWN, Neighbor Down: interface down or detached
LC/0/2/CPU0:Jan 20 08:56:40 : g_spa_3[158]: %L2-SONET_LOCAL-4-ALARM : SonetPath0/2/3/0: B3_TCA
LC/0/2/CPU0:Jan 20 08:56:50 : ifmgr[164]: %PKT_INFRA-LINK-3-UPDOWN : Interface POS0/2/3/0, changed state to Up
LC/0/2/CPU0:Jan 20 08:56:50 : ifmgr[164]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface POS0/2/3/0, changed state to Up
LC/0/2/CPU0:Jan 20 08:56:52 : g_spa_3[158]: %L2-SONET_LOCAL-4-ALARM : SonetPath0/2/3/0: B3_TCA cleared
RP/0/8/CPU0:Jan 20 08:57:00 : ospf[304]: %ROUTING-OSPF-5-ADJCHG : Process 200, Nbr 10.181.128.3 on POS0/2/3/0 in area 0 from LOADING to FULL, Loading Done
RP/0/8/CPU0:Jan 20 09:26:40 : ipv4_rib[225]: %ROUTING-RIB-3-UPDATE_TIMEOUT : Client "ospf" updated the RIB without signaling update completion for Vrf: "default" Tbl: "default" Safi: "Unicast"
Please help us to get route cause and solution to this error log.
Rgds,
Tejeshwar Saini

Hello Tejeshwar,
the OSPF adjacency comes up correctly?
is the device able to forward and receive over the link?
the message appears to just signal the OSPF process has modified the RIB table, because the OSPF neighbor came up, without providing a signal to another process and
This may be without impact or with impact on your device
if you see that there is an impact you should open a TAC service request.
if there is no impact, you may be able to live with this message
You are using IOS XR 3.6. TAC will probably suggest you an upgrade that can take the form or one or more SMU packages or a whole IOS XR upgrade.
Hope to help
Giuseppe

12000 GSR support of tunneling (GRE / IPinIP)

Can anyone please advise if the GSR (12000) routers support tunneling with either the GRE or the IPinIP protocols ?
If so please indicate which IOS version support those features.

no. The only tunneling supported on the GST is UTI.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120limit/120s/120s18/uti_gsr.htm

Ask the Expert: Cisco Prime Infrastructure - Implementation and Deployment

Welcome to the Cisco Support Community Ask the Expert conversation.
This Ask The expert Session will cover questions spanning Cisco Prime Infrastructure on Implementation and Deployment on Wired and Wireless. This will be more specific to Customer’s and Partners questions product covering PI on configuration, Features and Menu, Network Monitoring, Maps, Implementation, High Availability and Maintenance and t/s parts.
Monday, February 2nd, 2015 to Friday, February 13th, 2015
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Prime Infrastructure and Cisco Wireless products. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC) certifications.
Afroz Ahmad is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS),CCIE (DC), and SCJP (Sun Certified Java Professional )
Vinod Kumar Arya is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 8 years of industry experience working with large enterprise and service provider networks. He also holds VCP 5 and RHCE certifications.
** Remember to use the rating system to let the experts know you have received an adequate response.**
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure community, > Network Management, shortly after the event. This event lasts through February 13th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.

Hello Wilson,
Thanks for joining us.
1841 should just work fine for net flow . Hope you have a valid "PI Assurance license" installed on the server.
"PI Assurance license" is required for "net-flow" feature
Devices supporting Netflow in PI ::
1400, 1600, 1700 & 1800
2500, 2600 & 2800
3600, 3700, 3750 & 3800
4500 & 4700
AS5300 & 5800
7200, 7300, 7400 & 7500
Catalyst 4500 ASCI
Catalyst 5000, 6500, & 7600 ASCI
ESR 10000 ASCI
GSR 12000 ASCI
Cisco IOS Software Release Version
Supported Cisco Hardware Platforms
11.1CA, 11.1CC
Cisco 7200 and 7500 series, RSP 7200 series
12.0
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series
12.0T, 12.0S
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8600 series
12.0(3)T, 12.0(3)S
Cisco 1720, 2600, 3600, 4500, 4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)T
Cisco 1400, 1600, 1720, 2500, 2600, 3600, 4500,
4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)XE
Cisco 7100 series
12.0(6)S
Cisco 12000 series
NetFlow is also supported by these devices Cisco 800, 1700, 1800, 2800, 3800, 6500, 7300, 7600, 10000, CRS-1 and these Catalyst series switches: 45xx, 55xx, 6xxx.
NetFlow export is also supported on other Cisco switches when using a NetFlow Feature Card (NFFC) or NFFC II and the Route Switch Module (RSM), or Route Switch Feature Card (RSFC). However, check whether version 5 is supported, as most switches export version 7 by default.
You can check the below steps to diagnose the issue::
To verify that NetFlow is exported from a device to PI, follow the steps below:
1)   Browse to Administration > Data Sources page. Check the value in column ‘Last Active Time’ for the ‘Device Data Sources’ table. If the table is empty or the value does not represent recent time, then
it is possible that the device is not exporting NetFlow or PI Assurance license is not applied / expired.
2)   Login to PI console ( via SSH) as root user and run the command:
                netstat –an | grep 9991 – Output of this should be like : udp        0      0 :::9991         :::*
                Check the firewall settings on PI server using the command: firewall -L
1)   Check the configuration on an IOS / IOS –XE device. Run the commands
a)   sh running-config | inc destination
1)   This should list the IP address of the PI SERVER ( along with other outputs if any)
b)   sh running-config | inc 9991
1)   This should list at least one entry.
c)   If the above are fine, then verify that the flow monitor, flow exporter and the flow records are correctly configured on the device.
Refer to the URLs below to configure NetFlow export.
http://preview.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_monitor.html#wp1056427
Thanks-
Afroz
***Ratings Encourages Contributors ****

ACL based Forwarding in Cisco 12000

I have Cisco 12000 router running on XR 4.1.1 where i need to do below configuration.
track up_01
type rtr 103 reachability
track up_02
type rtr 113 reachability
track down_01
type rtr 104 reachability
track down_02
type rtr 114 reachability
ipv4 access-list DOWN
100 permit tcp any eq www any nexthop track down_02 1.1.1.2
110 permit tcp any gt 1044 any nexthop track down_02 1.1.1.2
200 permit tcp any eq www any nexthop track down_01 1.1.2.2
210 permit tcp any gt 1044 any nexthop track down_01 1.1.2.2
500 permit ipv4 any any
ipv4 access-list UP
100 permit tcp any any eq www nexthop track up_02 1.1.3.2
110 permit tcp any any gt 1044 nexthop track up_02 1.1.3.2
200 permit tcp any any eq www nexthop track up_01 1.1.4.2
210 permit tcp any any gt 1044 nexthop track up_01 1.1.4.2
500 permit ipv4 any any
interface x/x/x
description **UPLINK**
ipv4 address a.a.a.a b.b.b.b
bundle minimum-active links 1
load-interval 30
ipv4 access-group DOWN ingress
Issue is that i can not use NextHop option in ACL, Seems that is not available in XR 4.1.1
I found different opinion in http://www.cisco.com/c/en/us/td/docs/routers/xr12000/software/xr12k_r4-2/addr_serv/command/reference/b_ipaddr_cr42xr12k/b_ipaddr_cr42xr12k_chapter_01.html#wp5137027590
Do anyone have suggestion to do this config or any alternate configuration

hi there,
yeah you need PBR or ABF for this configlet you're showing.
dont believe that the GSR has that capability in that release.
If I see it right, then you need minimally 420+ for this functionality.
But also pay attention to the engine type cards you have, because there is likely a dependency there also.
xander

What is the maximum capacity of Edge 7206VXR Backend connectivity to GSR 12

hi,
we have one XDM 1000 and one GSR 12000 at one place
and in noc we have one xdm 100 and and one Edge 7206 VXR.
now we want to aggregate or increase the backend connectivity between EDGE and GSR.
can it possible the STM 4 or STM 16 bandwidth between these two routers.
can one can help me out

Tell me what bandwidth or data rate you expect. If you can specify that, I can provide you more options on which to use to achieve that bandwidth.

My photoshop elements 12 catolog is empty. I had over 12000 pics. what do I do

My photoshop elements 12 catalog is empty. I had over 12000 pics and they are all gone. what do I do

Most times when this happens, it just means that PSE forgot your original catalog for some reason and started a new one for you. Go to file>Manage catalogs and locate your old catalog, then repair and optimize it and it should work again.

How do I remove duplicate pictures in iPhoto and in folders?

I have 12000 pictures and duplicate annihilator is so slow and can only be used fopr 500 pictures. How do I remove duplicates pictures i iPhoto and in all the original folders?

What do you mean by "in all the original folders" ?
If you purchase and registers Duplicate Annihilator then the 500 photo limit is removed.
Regards
TD

GSR 12000 Router and Router 7609S

Similar Messages

Maybe you are looking for