GT 120 does not support resolution 1440 x 900?

Hi there.
I have a 15" Macbook Pro and wish to use the Apple remote desktop to control my 2009 Mac Pro remotely. However I can't figure out a proper resolution -- 1440x900 in the remote desktop... This resolution is not supported either when I work on the Mac Pro itself.
Suggestions are appreciated.
-oolong

Hi, SophiaHat and a Warm Welcome to Apple Discussions and the G5 Power Mac forum!
Do you have or are you buying a dual-core G5 with the PCI Express graphics?
http://www.apple.com/powermac/graphics.html
Which display do you have or are getting?
Can you link to the exact card you are thinking about?

Similar Messages

Iphoto does not support the resolution of my dslr camera...how do i upload full resolution photos?

iphoto does not support the resolution of my dslr camera...how do i upload full resolution photos?

You actually need to give information to get help - just stating an abstract problems (which is most certainly not a problem at all) gives the volunteers hearer nothing to work with to help you
What version of iPhoto? Of the OS? What exactly is the problem (iPhoto does support the resolution of your camera so that is NOT a problem)? what exactly are you doing? What error messages do you get? why do you incorrectly think that iPhoto does not support full resolution?
At this time your question is like my car won't start - why not? Could be anything from you did not put the key jun to being out of gas to having the engine stolen - no way to tell anything - except that the problem you claim is not true (at least in my example I would know that the car did not start)
LN

Installed graphics card does not support the opengl features recommended

I've installed FCP6 on my PowerMac (PPC G4 DP 1.25GHz), and when I run it, I get a warning ("...installed graphics card does not support the opengl features recommended...") and the program ends. The graphics card is the ATI Radeon 9000 Pro (64MB)
I'm looking for a definitive answer regarding my hardware compatibility with FCS2 (specifically, FCP6). I'm NOT looking for an answer along the lines of: your system is too old to run this.
I've checked the minimum system requirements from the apple website (http://www.apple.com/finalcutstudio/specs/
and http://www.apple.com/finalcutstudio/download/):
* A Macintosh computer with a 1.25GHz or faster PowerPC G4, PowerPC G5, Intel Core Duo, or Intel Xeon processor
* 1GB of RAM
* An AGP or PCI Express Quartz Extreme graphics card (Final Cut Studio is not compatible with integrated Intel graphics processors)
* A display with 1024-by-768 resolution or higher
* Mac OS X v10.4.11 or later
* QuickTime 7.3 or later
* DVD drive for installation
I have all that stuff. What I'd like is to know which component of my system is FCP6 complaining about (vis-a-vis the error message above), alternatively, if someone has had success with a similar configuration, I'd like to know anything they think might help.
Thanks in advance for any helpful advice you may have.

The minimum would probably be an nVidia Fx5200 or an ATI 9600...
Patrick

Lexmark does not support USB printing with Airport express

See email from Lexmark:
Hi Herman,
Welcome to Lexmark e-mail support. I appreciate your query into Lexmark.
Lexmark Inkjet printers are host based & work only USB attached. Currently Lexmark International does not support Airport Express on these printers.
If you have any more questions or concerns, please contact me at your convenience and I will be happy to assist you. (If I am not available, another representative will reply to you as soon as possible.) To respond, please select "Reply" in your e-mail software, and be sure that the past e-mail is included in this reply.
Regards,
Arshad
Lexmark Technical Support
***Original Message***
On Sun Jun 18th 03:20:53 PM EST 2006, hernan.
Dear Mamta,
Thank you very much for your support. I already tried what you
mention, but still without success. I downloaded again the x1100 all
in one driver but still I can't print.
Any suggestions?
Thank you,
Hernan
-----Original Message-----
From: [email protected] [mailto:[email protected]]
Sent: Sunday, June 18, 2006 7:30 AM
To: hernan
Subject: Re:Lexmark Technical Support (Req# 942782055)
Dear Hernan,
Thank you for contacting us regarding this matter. I appreciate the
opportunity to assist you, and I hope my suggestions will provide a
resolution.
Please follow the steps given below:
1. Click on "Start," "Control Panel" and "Printers and Faxes."
2. Right click on the Lexmark printer icon.
3. Click on "Properties."
4. Click on "Ports" tab.
5. Place a check mark against "Enable Bidirectional Support."
6. Click on "OK."
You may copy and paste the web address given below to access the
Lexmark 1000/1100 Color Jet printer Windows XP driver:
http://downloads.lexmark.com/cgi-perl/downloads.cgi?ccs=229:
1:0:1:0:0&emeafr
ame=&fileID=1580&searchLang=en&searchLang=en
Please use the following steps to download the Lexmark 1100 Color Jet
printer Windows XP driver to your desktop:
1. Click on "Download Now."
2. On the "File Download" screen, choose "Save."
3. The next screen will be titled "Save As." Choose to "Save in
Desktop"
and click "OK."
4. You should see files being transferred.
***Note*** If your browser uses a different file downloading format
than specified above, you will need to resort to your browsers help
files for downloading instructions. The object of steps 1 - 4 is to
download the driver to your desktop. This way it is easily accessible.
5. Once the files have completed downloading, double click on the icon
with your file name.
6. On the "Win Zip Self-Extractor" screen click "OK."
7. To unzip the downloaded file choose "Unzip."
8. A screen will then display the number of files unzipped
successfully, click "OK."
9. Please follow the on screen instructions to complete installation
of your Lexmark printer.
If you have any more questions or concerns, please contact me at your
convenience and I will be happy to assist you. (If I am not available,
another representative will reply to you as soon as
possible.) To respond,
please select "Reply" in your e-mail software, and be sure that the
past e-mail is included in this reply.
[AOL Users: In order to include the previous e-mail, you must
highlight it with your mouse when you are replying.]
If you need to reply, please be sure to include in your message all
information from prior e-mail messages & replies. If your e-mail
client automatically deletes prior e-mail thread information, it will
cause a delay while we look up your support history. If this is the
case you may want to save the old e-mails as attachments and attach
them to the current e-mail.
Sincerely,
Mamta V
Lexmark eSupport Team
http://support.lexmark.com
Rate Your Support Experience! Your feedback is extremely valuable to
us.
Please click the link below to participate in the Lexmark Customer
Support Survey.
http://support.lexmark.com//cgi-bin/survey.cgi?getSurveyID=7
07&getSurveyName
=
***Original Message***
On Sat Jun 17th 06:20:55 AM EST 2006,
hernan.>
I purchased the Apple airport express that connects
multiple
wireless-networked PCs to a usb printer.
is there a driver that can make this work?. I configured
the printer
according to the manual, received a test page and so on, but now it
takes ages to start printing and printing never gets to 100%
completion but to 99%. I am not able to cancel printing jobs and this
is a whole mess.
Best regards,
Hernan
vaio pcg-6c2l and IBM x40 Windows XP Both service pack2

Did you have a question?

Macbook Pro Retina HDMI Does Not Support 2560 x 1080

I have both the early and late 2013 rMBP 15 inch but it seems like the early 2013 does not support my Dell U2913WM at maximum resolution of 2560 x 1080 for some reason on HDMI. Are the HDMI ports any different between the two? I'm tried using SwitchResX, but at 2560 x 1080, I can only go up to 53 Hz before it says invalid configuation on the early 2013 rMBP. On the late 2013 rMBP, it can output 2560 x 1080 at 60 Hz fine. It would seem like both graphics cards are more than capable of pushing this resolution, and if I connect through Displayport, they're both fine too. I was hoping to use HDMI though to free up a Thunderbolt port. Why are the HDMI ports not outputting at the same capabilities?

Absolutely, I understand that but I'm wondering if or why Apple has limited the HDMI port on the early 2013 rMBP. HDMI 1.4 should be more than capable at outputting up to 4k resolution, so it would seem like Apple is intentially limiting the early 2013 rMBP to HDMI 1.2? At least one post from as early as 2012 seems to suggest that installing Windows on a rMBP allows higher outputs. I thought Mavericks included support for HDMI 1.4 (http://www.reduser.net/forum/showthread.php?101431-10-9-Mavericks-4K-working-tes ting-it-now) but did they not extend it down to the early 2013 rMBP? Seems like it would be able to support it, no?
Perhaps the better question is whether anyone has been able to output anything at over 1080P on anything other than the latest rMBP after upgrading to Mavericks?
From the earlier discussion:
"The port definitely supports it, but OS X is another story. If I boot into Windows and connect it to a display capable of displaying 2560x1440 over HDMI, it just works. If I'm in OSX, it refuses to allow anything over 1920x1200. Even if I try to force the resolution with SwitchResX, it doesn't work. If I create a custom resolution with a 40Hz refresh rate instead of 60Hz, then it does actually work. 2560x1440 @ 40Hz fits within the bandwidth constraints of a single link at 165MHz. So it appears that OSX limits the port to 1.2 frequencies. I'm not realy sure why -- HDMI 1.4 should allow for frequencies upto 340MHz, and the hardware is clearly capable based on Windows."
Now that Mavericks supports higher than 1080P over HDMI at least on the latest rMBP, did they just not extend that support to earlier rMBP's even though the hardware is capable of it?

TestStand Open SQL Statement does not support SQL's ORDER BY clause???

TestStand 1.0.3
Windows 2000 SP1
SQL Server 2000 Personal
You've got to be kidding me...
It appears that the built-in TestStand Open SQL Step does NOT support the
"ORDER BY" clause in the SELECT statement, even though the documentation
says it does. Is this true?
I have an Open SQL Statement query:
"SELECT * FROM [MyTable] WHERE ([Batch ID]=1234)"
it works fine, returning a correct record count 120 records. If I change
the Open SQL Statement query simply by adding an ORDER BY clause, such as:
"SELECT * FROM [MyTable] WHERE ([Batch ID]=1234) ORDER BY [MyField] ASC"
it returns a record count of zero. I know that "MyField" exists in the
MyTable table and contains valid data. The
second query works fine in SQL
Server Enterprise Manager.
Am I missing something? Is it true that the TestStand Open SQL Step does
NOT support the "ORDER BY" clause? If not, what &#$!ing good is it and why
does the manual state it is supported? Is there any other way using just
the TestStand steps to order a database recordset on one or more fields?
Any help would be appreciated.
Grrrrr....
Bob Rafuse
Etec Inc.

> Bob -
> The database step types do not do anything special to the SQL command
> that you give it. The step just passes the command to the ADO
> provider. I tried a simple query using the step types with the
> following command,
>
> "SELECT UUT_RESULT.* FROM UUT_RESULT WHERE ([UUT_SERIAL_NUMBER] =
> 12345) ORDER BY [EXECUTION_TIME] ASC"
>
> and this return the expected results and the record count parameter
> was as expected. I tried this on TS 1.0.2 and TS 2.0 with MS Access
> 2000 and MS SQL Server 7.0. I do not have MS SQL Server 2000 at this
> time.
>
> It would be surprised if the step types are messing something up.
I've been doing some experimenting over the past couple of days. Simple,
one-table queries seem to handle the ORDER BY clause fine. Th
ings seem to
get messed up when I try multi-table queries with ORDER BY clause with the
TestStand database steps. I get no errors but the returned record counts
are always 0 with the ORDER BY and positive without the ORDER BY. The exact
same queries work fine in Visual Basic/ADO and the SQL Server Query
Analyzer.
> Questions:
> 1. Have you verified whether the data is actually returned even though
> the record count is zero?
Hmmm... yes data IS getting returned (at least on the two instances I just
checked), but the record count is always zero. I was not proceeding with
processing if the record count was 0.
Still... I don't know how to loop through the recordset without knowing how
many records there are an not eventually generate an error by passing EOF.
Is there another way using the TestStand database steps to determine a) the
number of records in the recordset or b) when I'm at EOF?
> 2. Are you using any advanced options on the Opend SQL Statement step
> type, specifically
the cursor type set to forward only? Forward only
> cursors do not allow for record counts.
Everything on the Advanced tab of the Open SQL Statement step is set to "Use
Default".
Bob.

Lightroom CC does not support Intel HD 3000 on MacBook Pro - please add support !!!!

Installed the new Lightroom but it does not support the graphics on:
MacBook Pro (13-inch, Early 2011)
OSX 10.10.3 (actual version)
Intel HD Graphics 3000 512 MB
I see that Intel 4400 is required in Adobe Photoshop Lightroom Help | Lightroom GPU FAQ,
but this peace of Hardware is just only 4 yeas old .... !
please do add this !

Andy
Thanks... But again, why would I have to do this now when it was never a problem before?
In any case, all the footage I'm using in this project is XDCAM EX, the only difference being that some footage is 720, while other footage is 1080, and then there's also a variation in terms of interlaced and progressive footage accross the board (it's a rock band documentary, don't ask! )... Could this have something to do with it?
I kinda doubt it, cos one of the TV shows I work on has the same codec, resolution and other settings accorss the board, and I experience the same stutter on these projects...

Exchange 2007 New Install Error - Read only MultiValuedProperty does not support this operation

Existing Server/Exchange 2003 environment. New 2003 R2 x64 server fully patched and updated with no other apps installed attempting to install Exchange 2007 SP2.
Initially I was getting the error "Could not find the default Administrative Group ‘Exchange Administrative Group (FYDIBOHF23SPDLT)’". This I
fixed by completely uninstalling per this Microsoft article,
this Microsoft FixIt article and this recommended blog post, ending with
setup.com /preparead. I'm making progress, because now I'm getting a new error attempting the install. Specifically, Hub Transport installation fails with "Read only MultiValuedProperty does not support this operation."
Executing
setup.com /prepareSchema fails. I've set the msExchVer attribute for CN=Offline Address Lists to 4535486012416 and gotten no change, the install still fails. This
Googled page exactly describes my problem, and all anyone could say was to add this version number. It doesn't work. Pretty much none of the threads I've read have a resolution beyond this. I'm stumped, any help would be greatly appreciated.

What's the error message when executing setup.com /prepareSchema fails? failed at Organization Checks?
Could you please check whether you are on the right schema version?

Using Outlook for Mac; emails and calendar announcements will not send--error message: "the server does not support secure connections" Help?

Am using Outlook calendar for Mac--needed for client connection. Invites will not go out. Error message: "server does not support secure connections." Resolution?

I have done a similar set of things and no results.
This is really odd, Mac Mail works other emasil clients work, just not Outlook.
The only event I can tie it back to is the outage a couple of weeks ago when AppleID's weren't working for a perdion of time. I ended up having to reset mine.
Is it feasible a local certificate got corrupted at the same or, oddly, that the SMTP servers don't have the updated password?
What's odd is that I no matter how much i Google, i can't find anyone else who has this problem, other than here?

IIS proxy 5.1 and Weblogic 6.1 does not support sticky session

Dear Sir,
Our system is migrating from Weblogic 5.1 to Weblogic 6.1. After testing on
development environment, it is found that IIS proxy for 5.1 plug-in and Weblogic
6.1 server is perfect match for our case. Since our appliction system hit some
bugs of IIS proxy for 6.1. In development environment, one IIS match with one
Weblogic.
During production launch, another problem found. It seems that IIS proxy 5.1
plug-in with Weblogic 6.1 does not support the sticky load balancing. A sticky
service is one where a client sends its requests to the same instance and those
requests are not redirected to other instances. In production, two IIS match with
two Weblogic. Below is
#WebLogicHost=10.0.3.12
#WebLogicPort=8012
WebLogicCluster=10.0.3.12:8012,10.0.3.13:8012
COnnectionTimeoutSecs=10
ConnectionRetrySecs=2
ErrorPage=https://www.xxxx.com/eBank/sysnotready.htm
CookieName=eBankingWebLogicSession
Anyone have idea on out case?
Thanks,
KAI

My test was with 6.1 SP3.
The way to tell is by analyzing the cookie(JSESSIONID).
Perhaps the behaviour changed post SP1. I can't say for sure.
Eric
"Gary Rudolph" <[email protected]> wrote in message
news:[email protected]...
Is that entirely true concerning you don't need the persistence set to
replicated in the weblogic.xml to gain sticky load balancing?
The reason I ask was that in our situation sticky wouldn't work without
having the persistence set to replicated. This was with NSAPI and WLS 6.1
SP1. The weblogic servers were configured in a weblogic cluster. So..based
on this statement we should not have needed to set the persistence, but in
practice we did for it to work.
Gary
"Eric Gross" <[email protected]> wrote in message
news:[email protected]...
I just checked, and you are correct. You just need to have clustering
enabled in 6.1. You do not necessarily need to have persistence set to
replicated.
Of course, you won't get failover, but you will get the sticky load
balancing.
Regards,
Eric
"Ricky Wong" <[email protected]> wrote in message
news:[email protected]...
Why do we need to set session persistence to replicate in order to
perform
sticky load balancing ? There is no such requirement in WebLogic 5.1.
As
far
as I know, the IIS plugin simply interprets the value of the sessioncookie,
which should be embedded with the application server address, then
forward
the request to that particular application server.
We didn't use session replication in our environment because not allsession
variables are serializable.
"Eric Gross" <[email protected]> wrote in message
news:[email protected]...
The problem you mentionned in the other newsgroup post has been
fixed
and
will be in SP4. If you are in production or nearing production and
need
a
resolution now, then please open a case with support.
You should not need any other parameters to do the load balancing.
But
to
have the sticky load balancing, you must make sure you have session
persistence set to replicated for the webapp in question.
I'm not sure I am understanding your 3rd question.
In any case, my advice is to either wait for SP4 to bereleased(scheduled
sometime this month) or if you really need to go into production
soon,
contact support to obtain the latest IIS plugin.
Regards,
Eric
"Mike" <[email protected]> wrote in message
news:[email protected]...
Dear Eric,
Thanks very much for you kindly information, but we still have thefollowing issues
regarding the WL IIS proxy:
1. We have already tried the IIS proxy that comes with WL6.1 SP3.However, the
result from that version of IIS proxy is not satisfactory, as weexperienced cases
where the web page is not displayed correctly (as in
http://newsgroups.bea.com/cgi-bin/dnewsweb?cmd=article&group=weblogic.develo
per.interest.plug-in&item=994&utag=).
If there is any IIS proxy released after WL6.1 SP3, Could you
kindly
give
us
a pointer to the plugin?
2. In WL5.1 case, we are only required to have "WebLogicCluster"
parameter
set
to two weblogic servers in order use the load balancing features.
In
WL6.1, we
do not come across any additional settings required to support
load
balancing.
Is there any such settings required (e.g. in
config.xml,weblogic.xml,
application.xml,
etc?)
3. Does WL IIS proxy problem has anything to do with the version
of
the
IIS server/windows
versions that are using? we have already tried with IIS4 and IIS5
and
have
different
kinds of issues.
Thanks in advance for your kind assistance.
Mike
"Eric Gross" <[email protected]> wrote:
Yes, the session format has changed when using clustering and you
cannot
use
the 5.1 plugin to proxy to 6.1.
What problems did you have using the 6.1 plugin? Maybe you need
the
latest
6.1 plugin.
Regards,
Eric
"KAI" <[email protected]> wrote in message
news:[email protected]...
Dear Sir,
Our system is migrating from Weblogic 5.1 to Weblogic 6.1.
After
testing on
development environment, it is found that IIS proxy for 5.1
plug-in
and
Weblogic
6.1 server is perfect match for our case. Since our appliction
system
hit
some
bugs of IIS proxy for 6.1. In development environment, one IIS
match
with
one
Weblogic.
During production launch, another problem found. It seems
that
IIS
proxy 5.1
plug-in with Weblogic 6.1 does not support the sticky load
balancing.
A
sticky
service is one where a client sends its requests to the same
instance
and
those
requests are not redirected to other instances. In production,
two
IIS
match with
two Weblogic. Below is
#WebLogicHost=10.0.3.12
#WebLogicPort=8012
WebLogicCluster=10.0.3.12:8012,10.0.3.13:8012
COnnectionTimeoutSecs=10
ConnectionRetrySecs=2
ErrorPage=https://www.xxxx.com/eBank/sysnotready.htm
CookieName=eBankingWebLogicSession
Anyone have idea on out case?
Thanks,
KAI

Does the later 2009 MacBook support the Apple DVI to Video Adapter (s-video). I want to connect it to an old tv which does not support HDMI. Any suggestions?

I have a late 2009 MacBook which I want to connect to an old LG tv. The tv does not support HDMI it only has the (red, while, and yellow) ports. Sorry I dunno the exact name for it.
So I was thinking of using the Apple Mini DVI to Video Adapter (s-video), link below...
http://store.apple.com/Catalog/dk/Images/M9319_screen.jpg
But I'm afraid that the MacBook might not support the adapter.
Can anyone give me a solution for this? Is there an alternative way of doing this? I'm kinda new to apple display adapters.

The Late 2009 model 6,1 has a Mini DisplayPort not the Mini-DVI. To see which model you have go to the Apple in the upper left corner and select About This Mac, then click on More Info. When the System Profiler comes up check the Model Identifier.
Composite is the name for the red, white and yellow RCA plugs on your TV or red, white and S-Video plugs. If you want to use the Composite input on your TV there’s no Mini DisplayPort to Composite. You’ll have to get a Mini DisplayPort to VGA adapter http://www.amazon.com/s/ref=nb_sb_ss_i_1_19?url=search-alias%3Delectronics&field -keywords=mini+displayport+to+vga&sprefix=mini+Displayport+to and a VGA Adapter to TV S-Video RCA Out Cable for PC Video. http://www.amazon.com/VGA-Adapter-S-Video-Cable-Video/dp/B000Y7T5UU/ref=sr_1_7?s =electronics&ie=UTF8&qid=1316369974&sr=1-7
Only the Yellow plug or the S-Video plug for video will work. For sound you'll also need audio cables to the TV using a 3.5mm stereo headphone jack to RCA sound plugs. You attach it from the headphone jack of your MacBook to the appropriate input plugs on your TV http://www.amazon.com/s/ref=nb_sb_noss?url=search-alias%3Daps&field-keywords=min i-dvi&x=9&y=13#/ref=nb_sb_ss_i_2_19?url=search-alias%3Daps&field-keywords=macboo k+audio+cable&sprefix=macbook+audio+cable&rh=i%3Aaps%2Ck%3Amacbook+audio+cable

IE11/Win 8.1 error 'Your client does not support opening this list in windows explorer'

I hoping someone might be able to help with this frustrating issue.
I work on a project where we are using various versions of on-line SharePoint (2007/O365). In order to quickly drag and drop folders we need to often open the document libraries by using the 'open in windows explorer view'.
Using the same device, on occassion this works. But often it gives a rather unhelpful message 'Your client does not support opening this list in Windows Explorer'.
I've searched for this issue over the net and confirm that the sites are added to the 'trusted' sites area and that the 'remember you credientials' is checked on logging in.However, the searches do not seem to apply to IE11/Win8.1 or on-line version of sharepoint
(the suggested hot fix is not suitable)
Only this morning, using the same device I was able, for a short while to open in explorer view, and then for no apparent reason, it began to display the error message. I had changed nothing regarding settings or even closed the browser.
Do you have any support/ideas/fixes on how to resolve this.
Many thanks
val

Hi Val,
sometimes an answer can be found on the internet by typing the error message from your computer into your favourite search engine.
eg.
http://www.bing.com/search?q=your+client+does+not+support+opening+this+list+in+windows+explorer&form=IE10TR&src=IE10TR&pc=HPNTDFJS
see
http://blogs.technet.com/b/asiasupp/archive/2011/06/13/error-message-quot-your-client-does-not-support-opening-this-list-with-windows-explorer-quot-when-you-try-to-quot-open-with-explorer-quot-on-a-sharepoint-document-library-in-office-365-site.aspx
follow the directions given above.... you need to add the domains to your Intranet sites list, not the Trusted sites list.
Perhaps you already have it mapped to your intranet zone....in which case make sure that you have unchecked "Enable Enhance Protected Mode" on the Intranet zone dialog in Internet Options.
If this is happening 'randomly' on client machines, then users are probably changing their internet security settings in Internet Options. Ensure they are accepting the default.... Internet Options>Security tab, click "Reset all zones to default".
Consult with your system administrators to find out if they are applying a custom security template for the Intranet zone... It may be removing the sharepoint domains from the client Intranet zone's domains lists.
HTH.
Rob^_^

AS I FOUND OUT LATE, LION DOES NOT SUPPORT ROSETTA, WHICH SUPPORTS QUICKEN AND CLASSIC AOL, AND MANY OTHER APPS. CAN I TAKE LION AWAY AND GO BACK TO SNOW LEOPARD?

I found out after the install of LION, that it does not support Rosetta, which runs Quicken and the classic AOL software and a myriad of other apps.
Can I go back to Snow Leopard? Is there a way to retrieve my thousands of saved E mails, which are saved on my Mac?
I still see the filing cabinet with my screen name but cannot get them to open.
Please help! Lion may roar, but the fact it does not support apps like quicken means it purrs.

I had the Apple store wiped out my hard drive and I restore my last hard drive downloard by first placing Snow leopard DVD in the DVD drive and holding "C" when turning on the machine then I follow the instructions. I am back on snow leopard and trying out two finance software to replace Quicken for mac 2007. I am trialing Quicken essentials and ibank. They are both compatable with LION. So when I am ready will download Lion again. Also, Micorsoft Office needs to be 2011 version for it to work on Lion

I am told that my browser does not support iframes when trying to access a web site.

This is Google's cache of http://sitetrail.com/askearth.com. It is a snapshot of the page as it appeared on Sep 19, 2010 10:44:02 GMT. The current page could have changed in the meantime. Learn more
Full version These search terms are highlighted: history askearth com
* Contact Us
SiteTrail - Website News and Analysis
* Business
* Dev & Design
* Entertainment
* Mobile
* Social Media
* Tech
Search in SiteTrail askearth.com (visit site) This data was last updated 6 months ago (update data).
Site Profile Estimated Value: $5,582.16 USD Estimated Revenue: $7.60 USD per day $227.90 USD per month $2,772.81 USD per year Estimated Pageviews: 3,355 per day 100,648 per month 1,224,551 per year Alexa Rank: #447,581 Google Index: show google links Yahoo Index: show yahoo links Bing Index: show bing links History: show history Site Title: Interesting Questions - AskEarth Site Traffic
Site Server Server IP Address: 140.174.79.37 Server IP Decimal: -1934733531 Server IP Location: Pordenone, Friuli-Venezia Giulia, Italy
Your browser does not support iframes. Whois Information Welcome to the Network Solutions(R) Registrar WHOIS Server.
The IP address from which you have visited the Network Solutions Registrar WHOIS database is contained within a list of IP addresses that may have failed to abide by Network Solutions' WHOIS policy. Failure to abide by this policy can adversely impact our systems and servers, preventing the processing of other WHOIS requests.
To see the Network Solutions WHOIS Policy, click on or copy and paste the following URL into your browser:
http://www.networksolutions.com/whois/index.jhtml
If you feel that you have received this message in error, please email us using the online form at http://www.networksolutions.com/help/email.jsp with the following information:
Whois Query: askearth.com YOUR IP address is 174.129.155.56 Date and Time of Query: Tue Feb 23 00:49:37 EST 2010 Reason Code: IE DNS Records Host Class Type IP TTL Target Other askearth.com IN A 140.174.79.37 7199 askearth.com IN NS 7200 ns53.worldnic.com askearth.com IN NS 7200 ns54.worldnic.com askearth.com IN SOA 7200 mname: NS53.WORLDNIC.com rname: namehost.WORLDNIC.com serial: 108121504 refresh: 10800 retry: 3600 expire: 604800 minimum-ttl: 3600 HTTP Headers HTTP/1.1 302 Found Date: Tue, 23 Feb 2010 05:59:34 GMT Server: Apache/2.2.11 (Unix) mod_fastcgi/2.4.2 PHP/4.4.9 with Suhosin-Patch mod_ssl/2.2.11 OpenSSL/0.9.7m mod_apreq2-20051231/2.6.0 mod_perl/2.0.3 Perl/v5.8.7 Location: http://askearth.com/go/home Content-Length: 417 Connection: close Content-Type: text/html; charset=iso-8859-1
HTTP/1.1 200 OK Date: Tue, 23 Feb 2010 05:59:35 GMT Server: Apache/2.2.11 (Unix) mod_fastcgi/2.4.2 PHP/4.4.9 with Suhosin-Patch mod_ssl/2.2.11 OpenSSL/0.9.7m mod_apreq2-20051231/2.6.0 mod_perl/2.0.3 Perl/v5.8.7 Set-Cookie: id=11010246; EXPIRES=Sun, 01-Apr-29 00:00:00 GMT; PATH=/ Set-Cookie: pass=u0zit0yv; EXPIRES=Sun, 01-Apr-29 00:00:00 GMT; PATH=/ Set-Cookie: since=1266904775; PATH=/ Connection: close Content-Type: text/html Firefox Add-on SiteTrail Firefox Add-onPerform SiteTrail lookups via right-click menu straight from your web browser! Popular Lookups
* google.com#1
* facebook.com#2
* youtube.com#3
* yahoo.com#4
* live.com#5
* baidu.com#6
* wikipedia.org#7
* blogspot.com#8
* msn.com#9
Browse Lookups
A B C D E F G H I
J K L M N O P Q R S T U V W X Y Z Recent Lookups
* askearth.com#447,581
* evdenevenakliyatv.com#442,990
* mytaskhelper.com#756,476
* fikralari.net#639,299
* typemytape.com#1,547,530
* tmmod.info#1,078,434
* torrentplus.org#233,938
* communitycollegelistin...#430,008
* cadbury.co.uk#104,852
* myhobbyblogs.com#297,443
Random Lookups
* solidmastermind.com#931,183
* homelegance.com#277,584
* homepage-anleitung.de#1,091,134
* icicigroupcompanies.co...#1,513,887
* ptiboo.ch#744,058
* fachportal-paedagogik....#312,102
* lcpo.com#336,926
* spitinet.gr#904,561
* sportingpulse.com#37,069
* v-pillsbuyutucuhap.com#543,342
* sameskyboard.com#51,252
* alparslanpazarlama.com...#1,444,281
* ventausa.com#221,470
* dentalmag.org#234,937
* digitalfoci.com#1,214,872
* blank-label.com#273,247
* efun.ir#446,350
* greatamericandays.com#579,258
* it007.com#58,123
* hairyclipz.com#760,892
Navigation
* Contact Us
Categories
* Business
* Dev & Design
* Entertainment
* Mobile
* Social Media
* Tech
Recent News
* VP of Twitter Says Twitter is NOT A Social Network
* Google Puts White Spaces To Use
* YouTube Instant Experiment Gives Creator a Job At YouTube
* YouTube Time Machine – A New Website To Waste Hours On
* Google’s New Instant Search – Saving 11 Hours Every Second
* Facebook Notes Gets New Tools
Recent Lookups
* askearth.com#447,581
* evdennakliyateve.com#442,990
* mytaskhelper.com#756,476
* maximumwoman.com#639,299
* typemytape.com#1,547,530
* tmmod.info#1,078,434
© 2010 SiteTrail. All Rights Reserved.

I'm not clear on where you are seeing that text. When I view Google's cached page from the page found in this search
https://www.google.com/search?q=site%3Asitetrail.com%2Faskearth.com
It doesn't match yours exactly. There is an iframe with a Google map in it in the "Hosting Analysis" section, which in your pasted page seems to be the "Site Server" section.
Which Google site did you search?

Adobe Creative Cloud does not support Bootcamp by Apple IOS operating system, but does work with boot camp Win 8.1 why"

Adobe Creative Cloud does not support APPLE latest IOS operating system, but does allow Windows 8.1 to be accepted. This seems a shame to me, as
Apple IOS is the leader in graphics, photography. The advertising states it is usable under both APPLE IOS and Microsoft 8.1 windows operating systems. Adobe Support Chat Sooraj tells me on 02/19/2015 that i must buy two computers to have it operate on both operating systems. Adobe will not support apple's Boot CAMP allowing both operating systems.
i love the apple product and love the ADOBE Photoshop CC, but it simply does now work with an apple keyboard and a WiN operating system. .[email protected] Adobe Creative Cloud

In Thehatters defence, this was initially posted in the MacbookPro forum and then moved to Boot Camp,
If you have any joy solving your trackpad device driver issue, feel free to post here (there might be a similar fix for my wireless adapter device)
Thanks

GT 120 does not support resolution 1440 x 900?

Similar Messages

Maybe you are looking for