Guest Access to Internet NOT Working

We have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Can anyone PLEASE give me some fixes to this problem. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection. Any help would be appreciated. Thank you

What IP address do you get on that wireless computer?
Check the IP address on that computer and make sure that there is no static IP address. You will get IP address like 192.168.33.xxx.
Make sure that your router is running on the latest firmware.

Similar Messages

Guest access on E2500 not working but everything else is fine.

HI.. I did not use the CD to set up, and instead set this router up manually. We are using this router right now as a hotspot only.. and all is good. I can see both new networks and the WIFI laptops are talking no problem. Only issue I have is that guest access is not working - by that I mean it can't get out on the internet. I can see it as available and connect to it. Guest access and SSID broadcast are both enabled obviously.
Is there something special guests have to type into a browser? Or did I need to use the CD? (I read on a google search that cisco connect on the CD must be used?) Any help very much appreciated!

Really appreciate your help with this. I am a bit of a novice here.. but.. After some more searching on this issue I notice your comments (cut/pasted below) with respect to this router and bridging mode. You mentioned that I should update my firmware on this router and that this would (if I am interpreting your reply correctly) facilitate my LAN to LAN connection and of course using this router simply as an access point and more to the point - having the use of the guest network. So my question is even if I did update firmware, seems I would still require 3rd party software to make this work? (re your last sentence in your comments below) Just need to understand the process and determine whether or not it is worth it (or maybe I should upgrade the router) but I don't want to change the configs of the network wired router at this time... and need to use the E2500 or facsimile as simply an access point with guest network functionality, Thanks much appreciated.
"Again: some E series routers already support wired bridging in firmware, i.e. to use the router as simple access point.
This is and was always possible using a LAN-LAN setup instead.
The problem with the LAN-LAN setup is, however, that you have some limitations accessing the network storage or network printer, e.g. the router doesn't have the correct time and you cannot access the storage from remote using port forwarding through your main router.
These limitations have been overcome with the wired bridge mode (internet connection type = bridge mode).
But again: this has absolutely nothing to do with wireless bridging. That's something completely different and is not supported on Linksys routers in any firmware version so far. To do wireless bridging (i.e. the Linksys routers connects wirelessly to another main router) you need 3rd party firmware."

"access restrictions" did not work sometimes when using 3-tier DeskI.

My customer found that "access restrictions" did not work sometimes when using 3-tier DeskI.
But this issue can be solved by logging on from another machine, or restarting the DeskI.
For I can reproduce this issue, so I just want to know that:
1.What is it probably related to?
2.If this issue happens again, what can I suggest my customer for tracking it?
For example, get some log files from servers etc.
Thanks!

Hi Sarah,
Also you can try the following solution.
1. Import the universe.
2. Go to manage access restrictions
3. Remove the restriction .
4. Again create the rescrition and unchecked the " limit size of result set to"
5. Now assign it to the unlimited results group ( this is the name of
the group we have given to those users who should be able to retrieve
more than X rows)
6. Now we save the universe. (Dont export the universe).
I hope this will help you.
Regards,
Sarbhjeet Kaur

HT4993 why does my internet not work when not connected to wifi?

why does my internet not work when not connected to wifi

Hi farmgirl0812,
Thanks for using Apple Support Communities. This article has steps to try if you are unable to connect to a cellular network:
iPhone: Troubleshooting a cellular data connection
http://support.apple.com/kb/ts3780
Cheers,
- Ari

Windows 8 Last Access Time Stamps not working

Hi I have been trying to fix a issue with last access time stamps not working when I open a file
so will have time on created modified and accessed from when created but some are wrong like one file
saying
created ‎Sunday, ‎September ‎14, ‎2014, ‏‎5:19:32 AM
modified ‎Sunday, ‎September ‎14, ‎2014, ‏‎5:19:32 AM
accessed Sunday, ‎September ‎14, ‎2014, ‏‎5:19:32 AM
I'm not sure what can cause this please help thank you

Hi whowhatwere,
Are you only confused about the last access time not change when you open a file?
If you want to know more details about modified and created time, we can refer to the following KB.
http://support.microsoft.com/kb/299648/en-us
About the accessed time, please refer to the following blog.
How do I access a file without updating its last-access time?
http://blogs.msdn.com/b/oldnewthing/archive/2011/10/10/10222560.aspx
The blog mentioned that: In fact, the intuitive definition of access is more specific: It's "the last time I opened, modified, printed, or otherwise performed some sort of purposeful action on the file."
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

Internet not working and printer connected by cable but it is unable to communicate with the compute

Changed print cartridge and then problem started.
Internet not working and printer connected by cable but it is unable to communicate with the computer

Hi Joanna 59
Sorry to hear that you are having this issue and Hope you are well;
1.Do you see any light on the back on the printer where the cable is connected?
2. Do you see lights on the back of the router where the cable that comes from the printer is connected?
3.What type of cable are using to connect the printer? Have you try another cable to see if the problem is the current cable.
Please kindly include;
What router are you using (Brand and model)
Operating system i.e. Win 7
Complete Printer model
Thanks;
RobertoR
You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

Internet not working after turning Airport on

Hello,
All of a sudden, I can not connect to the internet when I turn the Airport on. The signal looks strong. But when I open my browser, it gives an error page. On a cafe where there is a free wireless internet that I go to often and had no problems connecting, gave me this message recently.
IP Configuration
192.168.1.46 in use by 00:18:39:88:81:fc, DHCP Server 192.168.1.1
Is there anything that I need to update in my Airport settings? If so, where? I have been trying to look for that and don't seem to have any luck.
Thanks for any help.
Rich
G4 Mac OS X (10.4.8)

See your other thread " Internet not working after turning Airport on".

Airport: Internet not working

Airport has self assigned IP address and will not connect properly to the internet. Have tried manually entering the IP address from another computer on the same network but still cannot connect to the Internet...Any advice/suggestions much appreciated

See your other thread " Internet not working after turning Airport on".

Cannot access the internet, not over wi-fi, nor over Verizon LTE; how do I fix it?

Have not been able to access internet for several days now. No access over wi-fi, or over the LTE.   Powered phone completely off and back on, but it did not help. What should I do next?

Problem has been happening on and off for a while; 2-3 weeks,
but have not been able to access internet at all for a week
or more. IOS version is 8.1.2.    Zip code is 44004.
Thanks
Original message -
>Date: Mon, 19 Jan 2015 19:28:03 -0800
>From: Verizon Wireless Customer Support
<[email protected]>
>Subject: - Cannot access the internet, not over
wi-fi, nor over Verizon LTE; how do I fix it?
>To: Cyndy Sleigh <[email protected]>
>verizon A message from the Verizon Wireless
       Community
        EXPLORE   SHOP MY VERIZON SUPPORT
         Cannot access the internet, not over wi-fi, nor
over Verizon
         LTE; how do I fix it?
       created by Verizon Wireless Customer Support in
iPhone 5 - View
       the full discussion
>

My internet not working

I must did something to my phone and the internet not working not on my wireless or att network that odd.
Safari could not open the page becuase the sever stopped responding that the error message but dail my phone still works.

I travel between Central New Jersey and New York City everyday, and EDGE has been awful for the past two weeks. In my wishful thinking, I've been turning flight mode on and off, and resetting the phone.
After seeing this, I can relax and put up with the crappy service
Today there is nothing...nada...zippo.

Port forwarding for the Web server for outside Internet (not working , help!!!!!!)

Hello
I am trying to learn something new here. We have web server inside our organization its IP address is 172.16.0.35. We want outside Internet users to access web server, How is it possible? Please have a look at the running configuration. Web server is working inside the organization but not at outside. Our Static Public IP is 197.255.232.15 it is assigned to Inetrface Gigabit ATM0.1 and ISP default GW is 197.255.232.1. Let me know whats next? How do I make web server inside the organization available for outside Internet users. Thank you.
Building configuration.
Current configuration : 1983 bytes
! Last configuration change at 17:57:15 UTC Sat Jan 24 2015
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router_test
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 10
ip dhcp excluded-address 172.16.0.34
ip dhcp pool test
network 172.16.0.32 255.255.255.224
dns-server 197.255.224.18 197.255.224.66
default-router 172.16.0.34
lease 9
ip cef
no ipv6 cef
license udi pid CISCO887VA-K9 sn FGL1818236L
controller VDSL 0
interface Ethernet0
no ip address
shutdown
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no atm ilmi-keepalive
interface ATM0.1 point-to-point
description ATM Routed Bridge Encapsulation (RBE) Internet
ip address 197.255.232.15 255.255.248.0
ip access-group netin in
ip access-group netout out
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
atm route-bridged ip
bridge-group 1
bridge-group 1 spanning-disabled
pvc 0/35
encapsulation aal5snap
protocol ip inarp
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Vlan1
description Lan
ip address 172.16.0.34 255.255.255.224
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1454
interface Dialer1
no ip address
ip default-gateway 197.255.232.1
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list natlist interface ATM0.1 overload
ip nat inside source static tcp 172.16.0.35 443 197.255.232.15 443 extendable
ip route 0.0.0.0 0.0.0.0 ATM0.1 197.255.232.1
ip access-list extended natlist
permit ip 172.16.0.32 0.0.0.31 any
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input all
end
http://pastie.org/9858814

Hi Karsten Iwen
I deleted ( ip access-group netin in and ip access-group netout out) but it still does not work
my config :
Building configuration...
Current configuration : 2267 bytes
! Last configuration change at 15:43:06 UTC Wed Jan 28 2015
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 10
ip dhcp excluded-address 172.16.0.34
ip dhcp pool my
network 172.16.0.32 255.255.255.224
dns-server 197.255.224.18 197.255.224.66
default-router 172.16.0.34
lease 9
ip cef
no ipv6 cef
license udi pid CISCO887VA-K9 sn FGL1818236L
controller VDSL 0
interface Ethernet0
no ip address
shutdown
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no atm ilmi-keepalive
interface ATM0.1 point-to-point
description ATM Routed Bridge Encapsulation (RBE) Internet
ip address 197.255.232.15 255.255.248.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
no ip virtual-reassembly in
atm route-bridged ip
pvc 0/35
encapsulation aal5snap
no protocol ip inarp
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Vlan1
description
ip address 172.16.0.34 255.255.255.224
ip nat inside
no ip virtual-reassembly in
ip tcp adjust-mss 1414
interface Dialer1
no ip address
ip default-gateway 197.255.232.1
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list natlist interface ATM0.1 overload
ip nat inside source static tcp 172.16.0.35 443 197.255.232.15 443 extendable
ip route 0.0.0.0 0.0.0.0 ATM0.1 197.255.232.1
ip access-list extended natlist
permit ip 172.16.0.32 0.0.0.31 any
line con 0
no modem enable
line aux 0
line vty 0 4
end
Router#sh ip nat translations
Pro Inside global Inside local Outside local Outside global
tcp 197.255.232.15:5183 172.16.0.33:5183 212.95.74.5:80 212.95.74.5:80
tcp 197.255.232.15:5196 172.16.0.33:5196 212.95.74.5:80 212.95.74.5:80
tcp 197.255.232.15:5602 172.16.0.33:5602 174.129.246.27:80 174.129.246.27:80
tcp 197.255.232.15:5785 172.16.0.33:5785 31.13.93.3:443 31.13.93.3:443
tcp 197.255.232.15:443 172.16.0.35:443 --- ---

"Automatically retrieve CD track names from internet" not working

I'm about to begin re-ripping all my CDs (400+) which I haven't done since at least 14yrs ago in order to take advantage on newer/better formats. I was excited to see that iTunes can automate a lot of this process with the following two options:
- When you insert a CD: (Import CD and Eject)
- [ ] Automatically retrieve CD track names from internet
Found in the "Playback" settings of iTunes 10.1.1
However after inserting my first CD, I noticed it started to import without downloading the track names first. Obtaining track names manually is working for me because if I choose "Advanced -> Get track names" it accesses Gracenote DB and works fine.
It's just the automatic operation after inserting a CD that is not working. This causes me to have to:
1) Insert CD
2) Choose "Advanced -> Get track names"
3) Click "Import CD"
4) Eject
as opposed to the one supposedly promised step of "Insert CD" and have the other 3 things happen automatically.
I've tried deleting my iTunes plists in my ~/Library/Preferences/ folder but it still works the same.
Any suggestions?

You can seach the Gracenote site directly. I don't know if that would help you decide which option you needed to use.
http://www.gracenote.com/music/index_old.html

Access Based Enumeration not working Windows 2012 R2 Datacenter

I am having a hard time figuring out why Access Based Enumeration is not working for me. I have set and re-set the settings and I'm still able to see folders I should not. I do get denied access on folders I don't have access to.
I have checked effective access which say everything is denied to me but I can still see the folder(s) listed.
I have the share permissions set to authenticated Users - Full Control
I have the NTFS permissions set to the correct Dept. Groups. - Modify, and Domain Admins - Full Control and Guests - Deny Full Control
Any idea's?
--------Update--------
I believe I had found the issue. It was a rights issue with a group that added to the local admins group.

Hi,
It seems that you have resolve the issue.
Please feel free to let us know if you need further assistance.
Best Regards,
Mandy
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Access Restrictions still not working with latest firmware

Linksys WRT54GS V5 with firmware v1.52.2
I cannot believe what a frustrating experience this is. All I want to do is block facebook.com from my two high schoolers until they’ve done their homework.
Starting out, it simply did NOT work, and I discovered from this forum that the initial firmware did not work for this feature. So here is what I did:
- Downloaded v1.52.2 firmware, which is indicated as being the latest for this router
- Upgraded the router, per the instructions with this firmware.
- Pressed (and held)the reset button for the indicated 30 seconds
At this point, my router switched back to the default access point name and access password. Fortunately, I had backed up my configuration, so I then:
- Loaded my previous configuration that included my Wireless security settings, different AP name, etc...
- Powered down, then back up router, cable modem.
Router now works wireless as before, but Access Restrictions still does not restrict. Router does list the correct firmware on the admin screens.
Here is how I sent up my one (and only policy)
Internet Access Policy: 1(facebook)
Status: Enable
Enter policy name: facebook
PCs: Allow checked
Days: Everyday checked
Times: 24 hours checked
Blocked Services: NONE
Wewbsite Blocking by URL Addresses:
3 entered, they are:
http://www.facebook.com
http://static.ak.facebook.com
http://apps.facebook.com
Website blocking by keyword: All 6 boxes empty
This was easier to do on my old netgear router, and it also actually WORKED. ARGHHHHHH

Thanks, but that did not work either. It seems to me that, entering mac addresses ended up totally taking away all internet access for the computers on the MAC list. This is really pathetic that a concept that on the surface seems so simple, as in 'deny access to hostname xxx.com' can be so difficult to implement. If there wasn't the suggestion that this were a feature of the router, I wouldn't care. But it *is* supposedly a feature, and the feature simply does not work.
It seem to me that LinkSys has too many mutually exclusive options on a single page. It would be easier to grok if the hostname filter had it's own page, then you wouldn't be wondering what the 'deny/allow' check box did or did not do in conjunction with your selections.
Does the feature work or not? As I mentioned, this was childishly easy to accomplish on my Netgear router. If it didn't suck so bad in other areas of performance, I'd simply go back to it.

Time access control does not work

I set up the time access control for my kids devices, but they can still access the internet.

Several possibilities exist:
1) The Timed Access entries are not being set up correctly. Have you tested each device yourself?
2) The kids are smart enough to know how to work around the settings
3) The kids know how to get on another nearby wireless network.
Regarding 2) and 3), there are numerous popular sites on the Internet that kids visit that provide them with tips and techniques to get around security on popular routers, so that possibility may be more real than you might imagine.
Regarding 1), we may be able to help, as there are two basic ways to set up Timed Access.....one being quite a bit more secure than the other. Unfortunately, this means a more time consuming and tedious set up.

Guest Access to Internet NOT Working

Similar Messages

Maybe you are looking for