Guest ssid with anchor controller and Web policy

We have a WLC4404 and and anchor controller WLC4402 to provide guest access to the wifi net. We configured both in the same mobility group, and the guest ssid to attach to the mobility anchor 4402. All is working fine until we enable the web policy authentication on the 4402. In this case the client join the guest ssid but neither get an ip address from the dhcp server nor go anywhere. Is we disable the web authentication all works fine again. We are runnig 4.0.206.0 on both WLC. Anyone can help us?

Two things you might check. (1) The 4404's mobility anchor should point to the 4402, and the 4402 should anchor to itself. (2) Make sure you are configuring the same security policy for the SSID on both the 4402 and 4404. So if the SSID is "guest" and you turn on web authentication on the 4402, make sure "guest" is on the 4404 with web authentication. We are using a similar setup for guest access at several sites.

Similar Messages

  • Central Web Auth with Anchor Controller and ISE

    Hi All
    I have a 5508 WLC on the corporate LAN and another 5508 sat in a DMZ as an anchor controller.
    I also have an ISE sat on the corporate LAN.
    Authenticate is working fine to the ISE and the client tries to re-direct to the ISE Portal but doesn't get there.
    DNS is working fine and the client can resolve the URL of the ISE to the correct IP address.
    I have a redirect ACL configured on the foreign controller which permits DNS, DHCP and traffic to and from the ISE.
    My questions are:
    1. Do I need to re-direct ACL to be present on both the foreign and anchor controllers?
    2. Since the Radius requests originate from the foreign controller do I need to configure the ISE server address on the WLAN on the anchor?
    3. Does the re-direct ACL need to be enabled on the advanced page of the WLAN on the foreign to over-ride the interface ACL - I don't believe it does.
    4. Is ICMP still blocked by the WLC until the web authentication is complete?
    Thanks.
    Regards
    Roger

    Hi Roger,
    Thanks for your brief explanation here are the answers for your queries.
    1. Do I need to re-direct ACL to be present on both the foreign and anchor controllers?
    The only catch is that since this web authentication method is Layer 2, you have to be aware that it will be the foreign WLC that does all of the RADIUS work. Only the foreign WLC contacts the ISE, and the redirection ACL must be present also on the foreign WLC.
    2. Since the Radius requests originate from the foreign controller do I need to configure the ISE server address on the WLAN on the anchor?
    Yes, you have to configure the ISE server address on the anchor WLC.
    3. Does the re-direct ACL need to be enabled on the advanced page of the WLAN on the foreign to over-ride the interface ACL
    Yes, you should override AAA under advanced tab of WLAN as ACL will be present on the foreign WLC.
    4. Yes, ICMP will work only after the sucessful web auth is complete.
    Please do go through the link below to understand the Anchor-Foreigh Scenario.
    http://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/115732-central-web-auth-00.html#anc11
    Regards
    Salma

  • Clients in Flex-connect SSID (with Anchor Controller) not able to connect with BYOD

    I have a WLC and having some SSIDs for Flex-connect mode (Mobility-group). Users trying to connect the wireless network using BYOD device but while they are trying to connect , it spins and spins . I checked controller , client is connected and got IP address and some users not but client says it spins and spins .No authentication prompt or no IP address
    Can anyone help me how to proceed to fix this issue .
    WLC : 2500
    Software Version
    7.4.110.0

    Hi
    I have tried this and things have changed slightly but it us still not syncing!!!! They are not talking!!!! my contact info is apparently not going to sync! ..... No good for my business !  Apple what are you doing.  Been loyal for 15 years!

  • Do Anchor controller and foreign controller have to run on the same code version?

    Hi All,
    I have a 4402 anchor controller and 8 4402/4404 foreign controllers all running on code 4.2.61.0 for 1 year without any problem. All guest users are connected to the foreign controllers and then tunneled back to the anchor controller. Right now I need to replace a 25-AP license 4402 foreign controller with a 50-AP license 4402 controller. The new controller is running on code 7.0.116.0. I am wondering if the new controller can join the mobility anchor group so that guest users won't lose connectivity after the swap.
    Please advise. Thank in advance.
    Robert

    Hi,
    The below link will answer ur question!! (Inter Release controller Mobility )
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7_0_116_0.html#wp568458
    Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • Using ISE for guest access together with anchor controller WLC in DMZ

    Hi there,
    I setup a guest WLAN in our LAB environment. I have one internal WLC connection to an anchor controller in our DMZ. I'm using the WLC integrated web-auth portal which works fine.
    To gain more flexibility regarding guest account provisioning and reporting my idea is to use Cisco Identity Services Engine (ISE) for web-authentication. So the anchor controller in the DMZ would redirect the guest clients to the ISE portal.
    As the ISE is located on the internal network while the guest clients end up in the DMZ network this would mean that I have to open the web-auth portal port of ISE for all guest client IPs in order to be able to authenticate.
    Does anyone know of a better solution for this ? Where to place the ISE for this scenario, etc ?
    Thx
    Frank

    So i ran into a similar scenario on a recent deployment:
    We had the following:
    WLC-A on private network (Inside)
    ISE Servers ISE01 and ISE02 (Inside)
    WLC-B Anchor in DMZ for Guest traffic (DMZ)
    ISE Server 3 (DMZ)
    ISE01 and ISE02 are used for 802.1X for the private network WLAN.
    Customer does not allow guest traffic to move from a less secure network to a more secure network (Compliance reasons).
    The foreign controller (WLC-A) must handle all L2 authentication and it must use the same policy node that the clients will hit for web auth.  Since we want to do CWA, we use Mac Filtering with ISE as the radius server.  If you send this traffic RADIUS authentication for Mac Filtering to ISE01/ISE02, it will use https://ise01.mydomain.com/... to redirect the client to.  Since we don't allow traffic to traverse from the DMZ with the anchor in it back inside to the network where ISE01 and ISE02 are, client redirection fails.  (This was a limitation of ISE 1.1.  Not sure if this persists in 1.2 or not.
    So what now?  In our deployment we decided to use a 3rd ISE policy node (ISE03 in the DMZ) for guest authentiction from the Foreign controller so that the client will use a DNS of https://ise03.mydomain.com/... to redirect the client to.  Once the session is authenticated, ISE03 will send a CoA back to the foreign which will remove the redirect for the session.  Note, you do have to allow ISE03 to send a CoA.
    In summary, if you can't allow guest traffic to head back inside the network to hit the CWA portal, you must add a policy node in a DMZ to use for the CWA portal so they have a resolvable and reachable policy node.

  • GUest WLAN with Anchor WLC - roaming problems

    Hello,
    my wireless network consists in 3 WLC 4402 which manage 40 APs.
    I have a fourth WLC which I installed on my DMZ for guest vlan anchoring and web autentication.
    Everiting works fine but I have a problem:
    If my client associates with an AP and then I authenticate I'm ready to make traffic. As soon as my client roams to an AP managed by a differnt WLC I need to authenticate again. If I roam back to the first AP i need to reauthenticate.
    In my guest WLAN I use WEB authentication provided by the internal web server of the Anchor WLC.
    Thnks everybody

    Here are the output of show mobility summary.
    The last WLC is the anchor.
    WLC1
    Symmetric Mobility Tunneling (current) .......... Disabled
    Symmetric Mobility Tunneling (after reboot) ..... Disabled
    Mobility Protocol Port........................... 16666
    Mobility Security Mode........................... Disabled
    Default Mobility Domain.......................... mob1
    Multicast Mode .................................. Disabled
    Mobility Domain ID for 802.11r................... 0x392f
    Mobility Keepalive Interval...................... 10
    Mobility Keepalive Count......................... 3
    Mobility Group Members Configured................ 2
    Mobility Control Message DSCP Value.............. 0
    Controllers configured in the Mobility Group
    MAC Address IP Address Group Name Multicast IP Sta
    tus
    00:23:04:7d:3e:e0 10.25.1.21 mob1 0.0.0.0 Up
    00:23:04:7d:73:20 10.20.1.21 mob1 0.0.0.0 Up
    WLC2
    Symmetric Mobility Tunneling (current) .......... Disabled
    Symmetric Mobility Tunneling (after reboot) ..... Disabled
    Mobility Protocol Port........................... 16666
    Mobility Security Mode........................... Disabled
    Default Mobility Domain.......................... mob1
    Multicast Mode .................................. Disabled
    Mobility Domain ID for 802.11r................... 0x392f
    Mobility Keepalive Interval...................... 10
    Mobility Keepalive Count......................... 3
    Mobility Group Members Configured................ 2
    Mobility Control Message DSCP Value.............. 0
    Controllers configured in the Mobility Group
    MAC Address IP Address Group Name Multicast IP Sta
    tus
    00:23:04:7d:3e:e0 10.25.1.21 mob1 0.0.0.0 Up
    00:23:04:7d:62:a0 10.20.1.22 mob1 0.0.0.0 Up
    WLC3
    Symmetric Mobility Tunneling (current) .......... Disabled
    Symmetric Mobility Tunneling (after reboot) ..... Disabled
    Mobility Protocol Port........................... 16666
    Mobility Security Mode........................... Disabled
    Default Mobility Domain.......................... mob1
    Multicast Mode .................................. Disabled
    Mobility Domain ID for 802.11r................... 0x392f
    Mobility Keepalive Interval...................... 10
    Mobility Keepalive Count......................... 3
    Mobility Group Members Configured................ 2
    Mobility Control Message DSCP Value.............. 0
    Controllers configured in the Mobility Group
    MAC Address IP Address Group Name Multicast IP Sta
    tus
    00:23:04:7d:3e:e0 10.25.1.21 mob1 0.0.0.0 Up
    00:23:04:7d:79:80 10.20.2.21 mob1 0.0.0.0 Up
    WLCAnchor
    (Cisco Controller) >show mobility summary
    Symmetric Mobility Tunneling (current) .......... Disabled
    Symmetric Mobility Tunneling (after reboot) ..... Disabled
    Mobility Protocol Port........................... 16666
    Mobility Security Mode........................... Disabled
    Default Mobility Domain.......................... mob1
    Multicast Mode .................................. Disabled
    Mobility Domain ID for 802.11r................... 0x392f
    Mobility Keepalive Interval...................... 10
    Mobility Keepalive Count......................... 3
    Mobility Group Members Configured................ 4
    Mobility Control Message DSCP Value.............. 0
    Controllers configured in the Mobility Group
    MAC Address IP Address Group Name Multicast IP Sta
    tus
    00:23:04:7d:3e:e0 10.25.1.21 mob1 0.0.0.0 Up
    00:23:04:7d:62:a0 10.20.1.22 mob1 0.0.0.0 Up
    00:23:04:7d:73:20 10.20.1.21 mob1 0.0.0.0 Up
    00:23:04:7d:79:80 10.20.2.21 mob1 0.0.0.0 Up

  • Problems with Ethernet controller and PCI device driver on Satellite L30-10X

    Hellow!
    Sorry for my bad English, I'm from Russia.
    Just few days ago I bought Satellite L30-10X with W Vista on board. My opinion, that this OS does't very good on this computer, so I install W XP.
    I have some problems with drivers. At first, I dont know what model I have:PSL30 or PSL33? I download all drivers for both models. But, after installation, computer doen't find drivers for Ethernet controller and PCI device...

    Hi
    Satellite L30-10X belongs to the PSL33E series. This number can be found on the label placed on the bottom of the unit!
    You have to choose this number from the driver download form to get the compatible XP drivers.
    I dont know why you are not able to install the LAN driver. Ive got the same notebook with Vista and Ive installed the XP and all drivers run fine.
    I assume you have installed the drivers in wrong order. Please take the look in the Toshiba installation instruction txt file. In this order you have to install the driver! Its important.
    I think you should install the XP again to ensure the clean registry and then download and install the compatible XP drivers like mentioned in the installation instruction file.
    Good luck

  • Installation issue with CS6 Design and Web Premium

    I purchased CS6 Design and Web Premium for school with a voucher from JourneyEd. I have downloaded (it took 13 hours not 1.5)and assume that it completed since I saw the files extracting in the download assistant. I always download to my desktop and install from there. I have two folders, CS6 Master Collection which is empty and CS6 Design and Web Premium which has three subfolders; Adobe CS6, Design and Web Premium and fonts. The first two have set-up file applications within them. There is no .exe file so I have run the set-up applications within these file folders. An installer appears and runs onscreen but nothing is installed. There are no error messages. I purchased this computer in June and it has more than enough space. I am using Windows 7. I really need this for school.

    If the current installation files you have downloaded are not working then please try downloading the trial of Creative Suite 6 Design and Web Premium from http://www.adobe.com/cfusion/tdrc/index.cfm?product=designweb_premium.  You can then enter the serial number for your purchase during the installation process.

  • Help with Radio Group and Web Service

    Hi,
         I created a Radio Group with Dynamic Entry List (Web Service).  It seems my list keeps coming back empty.  I am on SP10. 
         When I deploy I get warnings that "Entry List is missing output fields mapping.  I think this is a warning only because I don't have my form connected to any other components.  I just want to see the radio group populated. I don't think this is the cause. 
    I see references out there to this "Dynamic List" not working until SP12?  Can anyone add some insight to what is wrong?  unsupported until later?
    Thanks!

    I created a new model and the new model works fine.  Something must be cached.

  • Help with wireless controller and VLANs

    Hi I'm trying to setup a wireless controller in preparation for a large site go live later this year. I'm struggling to get the controller and the WLAN using the correct VLAN. I want the controller on VLAN 100 and the clients on the WLAN on VLAN 200.                 
    My thought is that I would need a config similar to:
    Switchport for wireless controller management port set to trunk VLAN 100 and 200 with no native VLAN set.
    The management interface on the controller set to VLAN 100.
    A dynamic interface created on VLAN 200.
    When setup like this I can get to the controller on its management address but only from VLAN100 not from another VLAN on site or from other sites over the WAN.
    I have setup a WLAN which is set to use the dynamic interface on VLAN 200.
    I have set the AP to use HREAP and set the native VLAN as 200 and added the dynamic interface into the VLAN mappings
    When I connecting a client to the WLAN I get an address on VLAN 100.
    The switchport for the AP is set to native VLAN 100 and trunk 200 – this setup works for standalone APs at other sites.
    What am I missing?
    Also any idea why the management interface address is not routing? The netmask and gateway are set correctly.
    Thanks
    Paul

    Just to add to Steve's post... You only need to create a dynamic interface for vlan 200 if you have ap's also in local mode.  If your ap's are in H-REAP/FlexConnect mode, you don't need a dynamic interface for vlan 200.
    In you H-REAP/FlexConnect ap, you would set the wlan to vlan mapping there and the switchport configuration would be a trunk allowing vlan 100 (im assuming your native vlan for your ap) and vlan 200.  You should see something like the following:
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • Creating DVD with PDF files and web links

    Hi all, first I'd like to say that these forums are a big help. I've spent DAYS scouring through topics learning. Of course, I know this opens it up for someone to post a link to a thread where my question has already been answered. Unfortunately, I haven't been able to find the specific help I need and would like to open a dialogue with experts.
    I am creating a marketing DVD for a product. We produced a video for it, but the client also wants the audience to have access to a large amount of research in this specific field. This exists as PDF files and links to websites.
    His previous Marketing CD was just that, a CD made with FileMaker and had the files and links and only worked in PC computers. I do not want to go back in that directions.
    I want to make an informative DVD with the video and a few pages of selling points and cool tricks (I discovered multilayered menus working on this!) for those viewing on TV or Computer, and then an option for Computer users to click for more info.
    How do I put PDF files on the disc and how do I put web links on there?
    Thanks,
    Byron

    DVDSP uses a tool called DVD@Access. It enables a user to link to URL and call such documents as pdfs. The problem is that its never was reliable - especially on the PC side of things.
    There have been many of posts in the last 2 days about its use. Do a search and you'll see.
    DVD was not designed with the web in mind - it was conceived long before that time. linking to "outside" documents requires a third party tool to take over.
    Just beware! - in fact if your client came to me I would refuse to do the job. I've seen the problems that exist doing work like this especially if your distributing to a large audience with different OS sets ups. If one of the users has Vista you can forget about it working at all.
    My suggestion would be to design a menu that tells the user the file paths to your pdfs or URLs on the disc.

  • CAC or smart card use with Oracle database and web server

    I've been asked to smart card (CAC) enable our Oracle web server and database access. We currently use CAC to access many of our other applications.
    Where can I find the following information
    Oracle software required (and is it an additional cost)
    How to integrate Oracle App server (web server) with CAC.
    How would I need to change the database users accounts to be CAC enabled rather than database users accounts.
    Thanks
    steven jackson
    [email protected]
    614-692-9768

    Virtualisation is not certified for Oracle RAC on Windows.
    +Certified Software on Oracle VM [ID 464754.1]+ note states:
    Oracle Real Application Clusters (RAC)
        Oracle 10.2.0.4 and up (10gR2) and 11.1.0.7 and up (11gR1) and 11gR2 RAC for Linux x86 and Linux x86_64 certified on Oracle VM
            Guest OS: Oracle Linux 5.1 (and above) RHEL 5.1 (and above) for Linux x86 / Linux x86_64
            Paravirtualized (PV) mode only (Guest OS and drivers)
            Only supported on Oracle VM 2.1.2 and above
            Live-migration of an Oracle RAC VM is supported with Oracle VM 2.2.1 and above.
            Previous versions are not supported. Please refer to this link for best practices.
            Over-committing CPUs is not recommended, but supported with the following restrictions:
                The total amount of VCPUs allocated to guest domains (running Oracle RAC guests), should not exceed
                two times (2x) the amount of real CPUs / cores in the Oracle VM server.
                The amount of VCPUs allocated to a single guest domain should not exceed the amount of real CPUs /
                cores in the Oracle VM server.
                Maintain Oracle VMs default VCPU allocation for dom-0: Oracle VM will allocate 1 VCPU for each real CPU or core to dom-0.
                CPU pinning is only recommended for hard partitioning. If no hard partitioning is required, CPU pinning should not be used.
            Static support only (dynamic support is being planned):
                Dynamic resizing of guest virtual machine is not supported (VCPU, memory and I/O)
                Virtual Machine Pause/Restore of an active Real Application Cluster virtual machine is not supported.

  • Trouble with xsd:any and web services

    I am trying to generate client code from a WSDL for a getter and setter for a chunk of XML.
    The getter:<s:element name="GetData">
      <s:complexType>
        <s:sequence>
          <s:element minOccurs="0" maxOccurs="1" name="id" type="s:string"/>
        </s:sequence>
      </s:complexType>
    </s:element>
    <s:element name="GetDataResponse">
      <s:complexType>
        <s:sequence>
          <s:element minOccurs="0" maxOccurs="1" name="GetDataResult">
            <s:complexType>
              <s:sequence>
                <s:any/>
              </s:sequence>
            </s:complexType>
          </s:element>
        </s:sequence>
      </s:complexType>
    </s:element>The setter:<s:element name="SetData">
      <s:complexType>
        <s:sequence>
          <s:element minOccurs="0" maxOccurs="1" name="id" type="s:string"/>
          <s:element minOccurs="0" maxOccurs="1" name="data">
            <s:complexType>
              <s:sequence>
                <s:any/>
              </s:sequence>
            </s:complexType>
          </s:element>
        </s:sequence>
      </s:complexType>
    </s:element>
    <s:element name="SetDataResponse">
      <s:complexType/>
    </s:element>When we use the <autotype> and <clientgen> ant tasks to generate our web service client code from the WSDL, we're getting the following warnings:
    [autotype] Autotyping for wsdl http://xxx.xxx.xxx.xxx:8080/xxx/xxx.asmx?WSDL
    [autotype] WARNING: Unable to fully map ['http://xxx.xxx/xxx/xxx/2005/11/30']:GetDataResultAnonType using javax.xml.soap.SOAPElement
    [autotype] WARNING: Unable to fully map ['http://xxx.xxx/xxx/xxx/2005/11/30']:dataAnonType using javax.xml.soap.SOAPElement
    [autotype] WARNING: Unable to fully map ['http://xxx.xxx/xxx/xxx/2005/11/30']:SetData using javax.xml.soap.SOAPElement
    [autotype] WARNING: Unable to fully map ['http://xxx.xxx/xxx/xxx/2005/11/30']:GetDataResponse using javax.xml.soap.SOAPElementOur client code for the getData() call looks mostly correct. There's a GetData object created with an "id" field. Typically, I've seen that when the web service method calls are generated, it gives me two ways to call:
    - one that takes a bean (in this case, a GetData object)
    - one that takes the actual fields (in this case, just a String)
    Only the method that takes the bean is getting generated, but that's not a big deal.
    The client code for the setData() call, however, is all screwed up. There is no SetData bean object, and the only method call that gets generated takes just a SOAPElement, the "id" field is left completely out. Without any way to specify the id of the data I'm setting, the setData() method call is worthless.
    My first suspicion was that the Ant tasks did not know how to handle the <any> tag. But we're getting exactly what we want, a SOAPElement object returned in the getter and a SOAPElement to set in the setter. The problem is that it's leaving out the "id" string in the setter. I guess I'm having a hard time seeing why it's almost working.
    Anyone have any ideas? I almost feel like this could be a bug. Sorry for the long post.
    Tobin

    Hi!
    Did you ever solve this? I get similar warnings for our wsdl, and can't figure out if they are the kind I can ignore, or if they indicate that my code will go down the drain :).
    /JMK

  • IPhone problem with iPhoto 08 and Web Gallery 08

    I have created web photo galleries in iPhoto 08. Then I have opened iWeb08 and created a page an added a web gallery widget for each of the galleries on this page, everything works fine. Now I fire up the iPhone and go to my iWeb page where the widgets are located.
    The problem is the web gallery widget appears on the iPhone screen as a blue cube with a question mark on two sides and some round grey circles on top. I can not access the galleries from iPhone. Are these cubes a representation for some program that the iPhone can't open? Any help is appreciated.

    I'd post your question in the iPhone forum because it seems to be an iPhone issue rather than an iPhoto one.
    Do you Twango?
    TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
    I've created an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. It's compatible with iPhoto 08 libraries and Leopard. iPhoto does not have to be closed to run the application, just idle. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

  • Export/import table with XMLTYPE data_type and fine_grained policy

    Hi friends!
    I'm trying to export a table with XMLTYPE and faine-grained policy.
    Source: HP-UX - Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64bi
    Target: Linux 2.6.18-238.el5 - Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production
    I do it thru exp/imp old utilities as mention in metalink ID 1318012.1.
    One of the things that surprised me after exp/imp is that the number of objects increased:
    Objects at Source:
    exp \"/ as sysdba\" owner=xml log=xml file=xml.dmp
    Type
    Number of Objects
    TYPE
    431
    TRIGGER
    6
    TABLE
    17
    PROCEDURE
    2
    LOB
    120
    INDEX
    17
    FUNCTION
    1
    On Target:
    imp \"/ as sysdba\" file=xml.dmp fromuser=xml touser=xml log=xml.log
    Type
    Number of Objects
    TYPE
    431
    TABLE
    32
    PROCEDURE
    2
    LOB
    429
    INDEX
    478
    FUNCTION
    1
    Why is this happening? Is it normal?
    Other problem that I found is triggers are not imported, why!?!?
    Thank you very much for your help!
    José

    Hi!
    The new squema was created empty. If I run the following query:
    select '10g', TABLE_NAME,COUNT(*)
    from  DBA_LOBS@DSN_HP
    where OWNER='XML'
    group by TABLE_NAME
    union
    select '11g', table_name,count(*)
    from  DBA_LOBS
    where OWNER='XML'
    group by TABLE_NAME
    order by 2,1
    As a result:
    Version
    Table_name
    Total
    10g
    ACTION_TABLE
    1
    11g
    ACTION_TABLE
    1
    10g
    Document1767_TAB
    14
    11g
    Document1767_TAB
    13
    10g
    Document1852_TAB
    14
    11g
    Document1852_TAB
    13
    10g
    Document1941_TAB
    16
    11g
    Document1941_TAB
    15
    10g
    Document2016_TAB
    14
    11g
    Document2016_TAB
    13
    10g
    Document2087_TAB
    13
    11g
    Document2087_TAB
    12
    10g
    IBT_XML_RECIBIDOS
    1
    11g
    IBT_XML_RECIBIDOS
    1
    10g
    LINEITEM_TABLE
    2
    11g
    LINEITEM_TABLE
    2
    10g
    PURCHASEORDER
    7
    11g
    PURCHASEORDER
    7
    10g
    PurchaseOrder1145_TAB
    9
    11g
    PurchaseOrder1145_TAB
    7
    10g
    RICARDO
    13
    10g
    RICARDO2
    1
    11g
    RICARDO2
    1
    10g
    RITNTFER
    1
    11g
    RITNTFER
    1
    10g
    RITNTFRE_08
    13
    11g
    SYS_NT3+LEU6vbfGLgQ18DLgrURw==
    69
    11g
    SYS_NT3+LEU6vffGLgQ18DLgrURw==
    76
    11g
    SYS_NT3+LEU6vjfGLgQ18DLgrURw==
    63
    11g
    SYS_NT3+LEU6vpfGLgQ18DLgrURw==
    1
    11g
    SYS_NT3+LEU6vqfGLgQ18DLgrURw==
    2
    11g
    SYS_NT3+LEU6vTfGLgQ18DLgrURw==
    65
    11g
    SYS_NT3+LEU6vXfGLgQ18DLgrURw==
    66
    10g
    TESTCLOB
    1
    11g
    TESTCLOB
    1
    There are many new tables created...I suppose because the differences between versions...
    Any ideas?
    Thanks a lot!
    José

Maybe you are looking for