Guest wireless setup not working on 5500 series WLC

I have a 5508 core WLC with a 3850 as the local controller for an AP3G2-K9W8-M Access Point. The 3850 and the core WLC both have the wireless guest WLAN configured. My client can see the wireless LAN. When it tries to connect, it fails.
Can you give me debug commands that I can run on the AP, 3850, and/or WLC to try to determine why it won't connect?

Thanks! I ran the debug - but I haven't found anything in it yet to help. Hopefully I have overlooked something that will help.
I created a test wlan with no security and it is not connecting either. Any additional thoughts would be greatly appreciated.
(Cisco Controller) >debug client 48-F8-B3-AE-EC-CF
(Cisco Controller) >*mmMaListen: Dec 26 19:31:19.493: 48:f8:b3:ae:ec:cf Adding mob
ile on Remote AP 00:00:00:00:00:00(0)
*mmMaListen: Dec 26 19:31:19.493: 48:f8:b3:ae:ec:cf Scheduling deletion of Mobile
Station: (callerId: 69) in 1 seconds
*osapiBsnTimer: Dec 26 19:31:20.461: 48:f8:b3:ae:ec:cf apfMsExpireCallback (apf_ms
.c:626) Expiring Mobile!
*apfReceiveTask: Dec 26 19:31:20.462: 48:f8:b3:ae:ec:cf pemApfDeleteMobileStation2
: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfReceiveTask: Dec 26 19:31:20.462: 48:f8:b3:ae:ec:cf 0.0.0.0 START (0) Deleted
mobile LWAPP rule on AP [00:00:00:00:00:00]
*apfReceiveTask: Dec 26 19:31:20.462: 48:f8:b3:ae:ec:cf Deleting mobile on AP 00:0
0:00:00:00:00(0)
*mmMaListen: Dec 26 19:31:20.485: 48:f8:b3:ae:ec:cf Adding mobile on Remote AP 00:
00:00:00:00:00(0)
*mmMaListen: Dec 26 19:31:20.485: 48:f8:b3:ae:ec:cf Scheduling deletion of Mobile
Station: (callerId: 69) in 1 seconds
*osapiBsnTimer: Dec 26 19:31:21.461: 48:f8:b3:ae:ec:cf apfMsExpireCallback (apf_ms
.c:626) Expiring Mobile!
*apfReceiveTask: Dec 26 19:31:21.462: 48:f8:b3:ae:ec:cf pemApfDeleteMobileStation2
: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfReceiveTask: Dec 26 19:31:21.462: 48:f8:b3:ae:ec:cf 0.0.0.0 START (0) Deleted
mobile LWAPP rule on AP [00:00:00:00:00:00]
*apfReceiveTask: Dec 26 19:31:21.462: 48:f8:b3:ae:ec:cf Deleting mobile on AP 00:0
0:00:00:00:00(0)
*mmMaListen: Dec 26 19:31:21.476: 48:f8:b3:ae:ec:cf Adding mobile on Remote AP 00:
00:00:00:00:00(0)
*mmMaListen: Dec 26 19:31:21.476: 48:f8:b3:ae:ec:cf Scheduling deletion of Mobile
Station: (callerId: 69) in 1 seconds
*osapiBsnTimer: Dec 26 19:31:22.461: 48:f8:b3:ae:ec:cf apfMsExpireCallback (apf_ms
.c:626) Expiring Mobile!
*apfReceiveTask: Dec 26 19:31:22.462: 48:f8:b3:ae:ec:cf pemApfDeleteMobileStation2
: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfReceiveTask: Dec 26 19:31:22.462: 48:f8:b3:ae:ec:cf 0.0.0.0 START (0) Deleted
mobile LWAPP rule on AP [00:00:00:00:00:00]
*apfReceiveTask: Dec 26 19:31:22.462: 48:f8:b3:ae:ec:cf Deleting mobile on AP 00:0
0:00:00:00:00(0)

Similar Messages

E1000 Guest password setup not working - security is not activated

I used Cisco connect to set up guest access with a secure password. Cisco Connect now indicates guess access is allowed and shows the password. However, when I actually try to connect to the guest network, it shows no security at all, and I can join the network without a password. What could be wrong?

In this case, Guest network gets connect to the network without asking the password. But any one try to access the internet then at that point of time it will ask for the guest password..

So my airport extreme recently had some nat/dns issue and in the airport utility displayed a warning about it and to correct it. I wasn't sure what to do so i pressed the resolve icon and now my guest network is not working.

So my airport extreme recently had some nat/dns issue and in the airport utility displayed a warning about it and to correct it. I wasn't sure what to do so i pressed the resolve icon and now my guest network is not working.

Anytime you change networking hardware, it is always a good idea to perform a complete power recycle of your networking components.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

HP 5524 Wireless does not work after firmware upgrade

HI,
I have just purchased an HP5524. After initial problems setting up the WPA key from the printer screen, I connected via USB, found the printer and swapped to wireless successfuly. I then installed the printer software on all my computers at home successfully over wireless.
The printer then needed a firmware upgrade to support eprint (?), which is successfully connected, downloaded the fireware, installed and went through the boot cycles successfully.
However, ever since wireless will not work. Before I return it to the retailer as "not fit for purpose" I thought I would ask the forum. The diagnostics downloaded a tool, which I went through, but this did not offer solutions that I had not already tried.
Thank you

Hi,
Thank you for posting you query,
In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen instructions.
If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"
(Although I am employed by HP, I am speaking for myself and not for HP)

Keyboard wireless key not working after upgrading to windows 8.1

Hello,
I am having hp pavilion dv6-6165tx notebook, where keyboard having a wireless button that turns ON and OFF all wireless devices, After upgrading to windows 8.1, HP Connection Manager is not getting installed, as well as Key is not working, key color turns red and white but no action is performed.
Kindly suggest me some solution.
Note: HP Doesn't provide drivers for windows 8/8.1 ONLY WINDOWS 7 for hp pavilion dv6-6165tx.
Thanks.

Hi @Jayesh_Bhadja ,
Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Pavilion dv6-6165tx Notebook and the Wireless keyboard not working correctly. Here is a link to troubleshoot the keyboard.
The HP Connection Manager is something that is for Windows 7 not Windows 8.1. I would uninstall this from your Notebook. Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system that need updating. It has a troubleshooting tool in this.
Make sure all your updates have been completed. I would try restarting my Notebook a few times.
If that does not help I would uninstall the keyboard from the Device manager.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Error message on my HP Photosmart C7280 All-in-One 'Wireless Radio not Working'

error message on my HP Photosmart C7280 All-in-One 'Wireless Radio not Working' My broadband is BT Infinity with a very strong signal throughout the house and my operating system is Windows XP. My printer will not connect wirelessly to my network, what can I do with respect to the error message 'Wireless Radio not Working'

Hello @GeoffH777 ,
Perfect! You are very welcome, I am very happy to hear the reset helped!
If you have a quick moment, please scroll back to my last message here and click the "Accepted Solution" button, so others can find our thread if they happen to run into the same issue.
Greatly appreciated, have a wonderful day!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Tecra A3 - Creative Mouse Wireless does not work

My Creative Mouse Wireless does not work while touchpad is installed.
Even if I disable the Touchpad, the mouse seal does not work.
Does anyone know how to solve this problem?
Thank you,
R.P.

Hello
On this way it is not easy to say what the problem is. I assume that you got some installations software for your external device. Install it and it should works.
As far as I know functionality of external mouse doesn`t depend on touchpad settings.
Bye

My wireless keypad not working even in a full battery, window display continously switching automatically without touching the cursor.

my wireless keypad not working even in full battery

I have a wireless keyboard with the attached keypad. The keyboard is working great, but the keypad quit working. I put in new batteries...did not help. Any suggestions?

5500 Series WLC internal DHCP Server - Exclusion?

Hi there,
We're using the internal DHCP server on our 5500 Series WLC which works fine.
However on one WLAN we ran out of addresses so changed the subnet from a /25 to a /24.
The problem is that the router/gateway is still in the middle (124/125/126) and not easily changed.
I've moved the WLC interface to the top of the subnet (251) but the router is more difficult as its externally managed/controlled.
So is there a way we can create a DHCP pool of .1 through 250 on a /24 mask but exclude 124/125/126?
Thanks
Mike
PS - Router subnet masks were changed so can see whole subnet.

Mike,
The WLC isn't a fully functional DHCP server, it only allows you to define what is in scope, not what is out of scope. Now if you have a cisco router/switch, you could use that for the DHCP server and specifically exclude the necessary addresses.
HTH,
Steve

Cisco 5500 Series WLC Field Recovery Compatibility

Is Software Version 7.2.111.3 compatible with Field Recovery Image Version 7.6.95.16.

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154556/cisco-5500-series-wlc-field-recovery-compatibility

Dell Inspiron 15 3000 Series, Problem installing Network driver, Wireless Key not working

Hi,
This is a brand new Dell, which has Windows 8.1 Pro 64bit installed, and I re-installed all drivers, and did BIOS update as well, but when downloading Network drivers with correct Service Tag and product, I get to the installation screen where it asks to Activate Wireless Key. The Fn + PrtScr does not work, even if I go to PC Settings, Bluetooth, I can switch it on with mouse, but when using the Fn + PrtScr it does not switch between On & Off within PC Settings. So I cannot install the Wireless drivers at all, I have to Cancel Installation.
Any suggestions?

The Service Tag may be listing the wrong wireless card variant. Please provide the hardware IDs so we can confirm:
http://dellwindowsreinstallationguide.com/downloading-drivers-checking-hardware-ids-and-downloading-and-installing-dell-system-drivers-in-the-correct-order/checking-hardware-ids-in-the-device-manager/

Guest network does not work when bridging airport express to extreme

Hello everyone,
i just upgraded my airport extreme 5th gen and airport express (dual band) to 7.6.3 which is supposed to enable guest network extenstion..
my airport extreme is hardwired to airport express (set as bridged mode), eveything works fine with internet connectivity and roaming between the two since both are set with the same ssd name and wpa pass, i have enabled guest network on both to test the new update, which worked fine with airport extreme, then i went downstairs to test airport express guest network which didnt work.. i can see and join the network, IPs are set correctly exactly like airport extreme.
while testing airport express guest network i noticed that i can only browse google website or google search results, youtube website can be accessed too but it will not broadcast youtube videos.. any other website cannot be accessed thru airport express guest network..
since airport express guest network is providing a very limited access i tried enabling vpn on my iphone and managed to get full access with extremely slow speed.. can this be a bug on the firmware, did anyone find a solution???
Thanks

AirPort Extreme is the main base station handlng DHCP and NAT for the network. Normally, I do not use the Guest Network feature of this dual band router, but decided to check out the new firmware.
The AirPort Express is normally connected back to the AirPort Extreme via a wired Ethernet connection so it functions as a separate access point in a roaming network configuration.
I tried out the Guest Network option in the new firmware on the AirPort Express and had no issues. Then, decided to try the Express out as a test connecting using wireless only. I moved it to a location that was about 30 feet and a few rooms away from the AirPort Extreme and enabled the Guest Function with no problems.
I would not expect your setup to work with the Guest Network features, since you do not have an Apple router installed and functioning as the main router for the network. That would be the device that "creates" the Guest Network and other AirPorts "extend" it using either an Ethernet or wireless connection.
Apple used VLAN for the Guest Network feature before and I assume that has been expanded somewhat with the new feature to extend the Guest Network option to other Apple routers on a network.

Guest network does not work

Hi
I have latest Airport Extreme with 2TB hard disk (Time Capsule). I have working private network after latest firmware update (7.7.2 here) except my guest network. I have tried to setup the guest network as open network and WPA/WPA2 network with password but it does not work.
I can see the guest network but when I try to connect to it the connection does not work (= there is no internet connection or I cannot connect at all). Private network works fine (WPA2 Personal). Router mode is off (bridged network).
Any ideas how to get it work?

Router mode is off (bridged network).
Any ideas how to get it work?
The TC will nor produce a working guest network without being in Router mode.. ie DHCP + NAT.. you will not get it working in bridge.. it tricks you.. it looks so like it is going to work.. but no. it cannot.
You must rearrange your network so the TC is main router..
Or
IMHO the easier way is to go and buy a cheap wireless router.. a $35 tp-link etc.. and simply use that as AP. It is cheaper, easier and much faster.. guest network is still adding clients to the same wireless.. whereas setting up a second AP allows you to have an entirely separate connection.

Wireless connection not working after installed newest Lenovo ThinkVantage System Update programs

Hi, everyone!
I've installed some newest programs through Lenovo ThinkVantage System Update and just after that my wireless connection has stopped working. Here are the installed programs:
ThinkPad UltraNav Driver for Windows 32-bit version 15.0.24.0;
ThinkPad Power Management Driver version 1.60;
ThinkPad Modem Adapter version 7.80.8.0;
ThinkPad Hotkey Features Integration Package Setup version 3.11.0001;
Inter Wireless WiFi Link for Window XP version 13.02.0000;
ThinkVantage Access Connections for Windows XP version 5.62;
ThinkPad Power Manager version 1.88;
Lenovo ThinkVantage Toolbox (32-bit) version 6.0.5514.61.
I've got a Lenovo T61 with Windows XP SP3.
Also in Device Manager, there are now the two "Other devices" bellow with a yellow question point and a yellow exclamation point by side:
Bluetooth Hands-free Audio;
Bluetooth LAN Access Server Driver.
Does anyone have any idea what can be done to have these issues solved?
P.S.: when I click Fn+F5 it shows only the Bluetooth Radio.

Hello and welcome,
I've seen something like this on XP machines after updates a couple of times now - my T61, a friend's T400, and his daughter's T61. I guess that makes 3
_Maybe_ your situation is the same.
The fix in all 3 cases was to go to device manager and uninstall the wifi driver. Then scan for hardware changes and let it reinstall the driver. Something about how Access Connections or some other networking mangement thingy was hooking the drivers I guess.
On both of the friend's machines, the wired networking was also b0rked. Same fix there.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Wireless printing on HP 6500A Plus -wireless does not work

windows 7, linksys E2000 router, sony vio computer wireless N.
No issues printing by USB. When using wireless, prints first few lines, then slows to a stop. Loses feed from router and disconnects. Tried disabling all firewalls, removed antivirus, etc - nothing is working. Not the only computer in household with same issue as well - Toshiba running xp is having same problems. Need fix or I will trash printer and never purchase HP again and I have long been an HP customer for printers.

There have been a few issues with printing using the new E-series Linksys routers. Make sure the router has the latest firmware. If that does not work, set a static IP address for the printer:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). Yours is 192.168.1.100 to .149. Let's use 192.168.1.200 for your printer.
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Enter your router's IP (on the Network Config Page) for the gateway and first DNS. Leave the second one blank.
- Click 'Apply'.
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Guest wireless setup not working on 5500 series WLC

Similar Messages

Maybe you are looking for