Guitar and USB SB Live! 24-bit Exter

Hallo all,
I was eager to buy the aforementioned SB model (USB SB Li've! 24-bit External) as my laptop doesn't seem to get any input from my guitar through the embedded sound card.
I was wondering, as this is the primary and only reason for me to buy this model, if I could plug my guitar in the input jack and record from there, or if a little amp is needed (as for other cards).
Any idea?
Thanks in advance for any kind response,
-marco-

okram wrote:
Hallo all,
I was eager to buy the aforementioned SB model (USB SB Li've! 24-bit External) as my laptop doesn't seem to get any input from my guitar through the embedded sound card.
I was wondering, as this is the primary and only reason for me to buy this model, if I could plug my guitar in the input jack and record from there, or if a little amp is needed (as for other cards).
Any idea?
Thanks in advance for any kind response,
-marco-
Hi
When you use LineIn for guitar you propably need a preamp (Guitar amp with LineOut, DI
box, POD, Mixer, ...).
If you use MicLine then you propably get a weak sound (set mic boosting +20dB, if there
is this setting on Li've! software).
Check also settings on Creative Mixer (input source, rec source, and levels).
(I do not have this card/software so I'm not sure 'bout what mixer settings you have.)
.jtp

Similar Messages

Blue screen after installing creative soundblaster live 24-bit exter

hey,have a bit of a prob here...i get random crashes after installing my external soundcard which i've just bought...i'll get the blue screen everytime it happens but unable 2 catch the blue screen msg as it flashes for 2 secs...anywayz i'll explain my com setting...i'm using a acer travelmate 270,about 3 yrs old now...it has 3 usb . ports at the rear n i added 2 usb 2.0 slots via pcmcia card...i connect my external hard disk using the 2 usb ports at the back as port has not enuf power..so that leaves port...n the pcmcia card ports i attach a external cd burner n a usb 2.0 hub....could it be that the error msg im getting is due to the lack of current in my laptop?is there a way 2 check the power capacity on the usb ports?the blue screen has appeared numerous times alredi n is very annoying...but i managed to solve the prob though for now when i go to control panel/sounds and audio devices..then under the volume tab,i goto speaker settings/advanced/performance..in here,i lower the hardware acceleration bar to the 2nd bar n the sample rate conversion quality bar to the st bar ...the crashes haven't happenned so far....but just wanna get anyone's opinion on why the blue screen crashes happen...isit bcoz my laptop is unable 2 supply sufficient power to the external soundcard when functioning at its full capacity?(causing me 2 lower its performance via lowering the bar)any help would be much appreciated...thanx.....

Have you try installing the X2 Dual core processor driver?
http://www.amd.com/us-en/Processors/..._87_38,00.html
Jason

Connection Logitech Z-680's to Creative Sound Blaster Live 24 Bit Exter

Trying to connect my Logitech Z-680?Speakers to connect to my Sound card. I can either use optical or the analog (3x 3.5mm jacks)
What is the best way to connect them?Also on the speakers depending on which cables i used, i have different effect options. If its using the analog :-6 channel directstereostereo x 2DD PL 2 MusicDD PL 2 Movie?If using optical:-StereoStereo x 2DD PL 2 MusicDD PL 2 Movie?Which should i use?for Music i will change the effect to DD PL 2 Music - so i get 5. sounds from my tracks. But which for movies?Are they're any changes that i have to make to the DVD program that i use?Also should i have CMSS on the soundblaster on or off?Thanks

I recommend using Optical (since its digital connection). (Also for to send to an external reci'ver to decode Dolby digital and DTS i beli've you need to use SPDIF (optical) out cause otherwise analog i beli've won't do it)?Those modes you?said?are up mixing modes for 2 channel sources like music?(best used with digital connections). Since movies are already 5. you don't need to use up mixing.
CMSS is for use on?analog?connections on the soundcard?only and is upmixing 2 channel?sources like music. Games i would recommend?analog since gaming can't do surround sound over digital. Depending on your DVD app wether it has SPDIF out is on the app. if its supports it should be fine.Message Edited by Stargazer on 02-24-20062:27 AM

Sb live 24 bit exter

Ive just bought a soundblaster li've 24bit external soundcard. I seem to be having problems playing BF2. I have disabled my onboard soundcard. (atleast i think i have). This is what appears in my device manager box.
audio codecs
legacy

Ive had to do a full reinstall of xp. I havent added my soundblaster li've 24bit external soundcard. I am using my original motherboard sound device.
I need someone to tell me which of these things i need to disable before i run my new external soundcard.
here is my list.. audio codecs
legacy audio drivers
legacy video capture devices
media control devices
mpu-40 compatible midi devices
nvidia nforce audio codec interface
nvidia nforce mcp audio processing unit
standard game port
video codecs
Ive noticed only a couple of these can be disabled. if i unistall any of them they reappear as soon as i restart windows.
please help me im a noob

Installed Windows & 32 Bit But Drivers and USB ports NOT WORKING.

I bugh an HP Pavillion TS 14 Notebook that came preinstall with Windows 8.1 64 bit which I hate so wiped the drives and installed Windows 7 32 bit and now I have a big problem. None of my network drivers work and the 2 uSB ports where I plug my mouse and other SB hardware in no longer work.
I did a back up of the SW Set up file that has all of the HP dvers for my laptop but both the network and video divers won't install. And When I try to install the drives I get the eror message saying they are not compatible with this version of Windows.
I have loked on the HP website under my laptop model which s as above but HP don't do drivers for Windows 7 32 for my laptop. And I have looked on both the Realteck website for both the Realteck ethnet and Realteck wireless network drivers but none of them work or install on my operating system. The video drivers Intel don't work either. So I am really stuck a I cannot go back to Windows 8.1 as though that 32 bit Windows 7 would work on my laptop but most of my drivers are not compatible with the operating sytem And I don't want to install 64 bit Windows as I like 32 bit.
The drivers that are not working on Windows 7 32 bit are:
Realteck RTL8188EE 802-11b/gn witeless lan
Realteck ethnet die and
Intel High definition graphcs driver
Which don't work at all on Windows 7 32 bit as they are 64 bit only drivers.
So can you please post me a link bth the network and Intel graphics drvers that work with my laptop. As I have tried lots of different Realteck and raphics drivers for Window 7 but NONE of them work on my system. And None of my USB ports are working either. So how do I solve this problem?
This question was solved.
View Solution.

Hi:
Should be no problem to get W7 32 bit to work on that model.
Just use all of the drivers and software from the HP Probook 450 G0 on your model except the Audio, BIOS and firmware files.
Your model uses the Intel HD graphics driver only.
The first driver you have to install is the Intel chipset installation utility and then reboot.
http://h20565.www2.hp.com/portal/site/hpsc/public/psi/swdHome/?cc=us&lang=en&sp4ts.oid=5359407&ac.ad...
Audio: Accept the agreement. Download and install the first driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=24&Level=4&Conn=3&DownT...
If for some reason, the Intel HD graphics driver from that model does not work, then use this one...
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23713

Integrated SB Live 24 bit on K8N Neo4 SLI Plat and custom EAX

I want to be able to create some custom EAX settings but I can't seem to find any way to do that on the SB Live 24 bit that's integrated on the K8N Neo4 SLI Plat board. Is anyone able to do this or is it a limitation of the integrated SB Live 24 bit? I hope it's not the latter... Thanks.

Hello, uninstall your sound drivers and go to creative site and get the lastest drivers with creative sound console, install both this sould work.. also clean out all the old sound drivers after uninstalling with driver cleaner. I think thats how i did it. good luck henry9

PS3 Guitar Hero USB Microphone works with iPad and GarageBand ! :-)

I have a white USB adaptor that I use to connect my digital camera to my iPad. This morning I connected my guitar hero USB microphone into it and it worked using GarageBand !
I have not heard any distortions.... Is there anybody else out there that can also test this scenario ???
If you already have this mike, why pay more for another one that seems to do the same thing ??
Cheers,
Cyberjo

Was anyone able to get a singstar microphone to work with the camera connection kit? (i got it working with my windows computer.)

Windows 8.1 64 bit and USB 3.0 connection Error

What a Nightmare to me after I have purchased my Probook 470 G2 with window 8.1 64bit and USB 3.0. after my setup for my new laptop, there are 2 issues i am facing now:
1. my USB 3.0 external drive can work properly with my old window 7 laptop with USB 3.0 input. However, my USB 3.0 exernal drive can not function proplery when i try to plug in to my new laptop with window 8.1 64bit. it show me that it sometimes disconnect, sometimes connect frequently and I can not remove the drive safely
2. Once the laptop set up, there is 3 partition from HP, which is windows (c, recovery (D and HP tools (E. as i want to allocate more space fo save my old photo, HP technician has taught me to compress and release some space(around 150GB) from my C: . I can use the new drive successfully. However it seems i can not have window update manually so I am concerned if this is the mian point to create this issue.
Any HP technicians can help here?
This question was solved.
View Solution.

No. There is no need to go to a command line and there aren't any DOS commands that will help.
You should consider using Windows system restore to return your notebook's operating system to a date before this issue began. Choose a restore point dated before the problem surfaced.Use the search charm and type in restore. Choose create a restore point. The System Properties window will appear. Click on System Restore as seen in the following image.
Make certain the show me more restore points option has a checkmark in the box. Choose the restore point that you want and then click on next. This is safe and reversible.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Mac Mini and USB 2.0 hubs (hubs stop working within a month)

I have an aluminum Mini running OSX 10.6.6 (Snow Leopard). With only 4 USB ports, I have need of a USB hub to accommodate my external drives and other peripherals: keyboard/mouse, camera and iPhone have to use the existing ports in the Mini (difficult access to ports due to space limitations), leaving one port for up to 4 external drives (older drives 40-60gb used for backup and extra storage).
I have problems using powered USB 2.0 hubs with this computer; I have 'burned out' 2 hubs since buying the Mini in February. They just flat out stop working, though they still show power (the power indicator light on the hubs); no peripheral is recognized when plugged into the hub (which worked fine for about a month). I can unplug the 'must use Mini ports' (camera, iPhone, charger, etc) and the peripheral drives are recognized and work normally when plugged directly into the Mini ports.
One hub was a Belkin 4-port hub (about 1 year old) and the other was a GE 3-port hub with several flash card readers (19-in-1 card reader), also about a year old. Is there any reasonable explanation why powered hubs would suddenly stop working, related to use with the Mac Mini 2010 aluminum version?
I had worse problems with the USB ports in an old (~2006) Mac Mini (out of warranty), where the USB ports in the Mini stopped working, which is partly why I bought the new mini. In light of this tidbit, (be honest, please) are there known issues with Mac Minis and USB?

Each of the external drives has its own power supply; I generally only use one drive at any one time, but on rare occasions I have powered up more than one to confirm or transfer files. I don't leave any of those drives on when not in use, and when everything is working I properly eject/unmount them before turning them off.
There have been times when I powered up a drive connected to a powered hub and both the hub and the drive indicated activity but the drive didn't mount. On those occasions the drives sometimes would not appear in Disk Utility, and other times would appear, but would not be "mountable". I didn't know what the best way to deal with that was, so I would just turn the drive off, hoping the lack of mounting on the desktop meant no real drive activity was occurring and I wouldn't risk data loss or drive damage. So far all the drives seem to work fine when plugged directly into the back of the mini.
The main external hard drive I was using when the Belkin hub failed (iomega 40g) is USB 2.0 only (no firewire). I have another drive that is only firewire (la cie 60g)... so it wasn't a factor. Two other external drives are ACOM, one 40g one 120g, and then there's my old iMac G5 disk (display fizzled and everything but the disk recycled through Apple's recycling program) which is mounted in an external enclosure and is part of the USB contingent, but is not being used for anything but backup (all three both USB 2 and FW400 capable). (I know, too many toys... but why throw them out?)
The USB hubs both had their own power supplies, too, and I never used them without power (though I tried it as part of troubleshooting, before reading the Apple article on USB and power requirements). Other USB devices that only work when plugged into the mac directly are my Epson Stylus CX4800 all-in-one, and my Radio Shark.
So, whaddya think? Should I risk buying another powered USB hub or just live with plugging in peripherals to one available USB port (through a short USB 2.0 extension) and only use one at a time? That would be a bit of a pain, but if there are no issues you've heard of with Mac USB ports (several unanswered questions in the Mini Support forums here involving USB and peripherals, I noticed), what else would explain the seemingly short lives of USB hubs?
Oh, here's something I just remembered: the last time the Belkin hub was working (last night), I had my Radtech BT mouse charger cable plugged in (not charging, mouse not attached) along with two of the external hard drives, and my Fuji camera USB cable. I got an error message onscreen (on the Mini) that a drive had been improperly ejected (or put away?), yet the hard drive in question was still mounted on the desktop. I looked at the hub, and the loose ends of the charger and the camera USB cable were touching. Could that have caused the error (and maybe the hub to fail)? (Edit: the camera cable I think was plugged into the mini's one available port; 3 external drives and the mouse charger were plugged into the hub, _but only one drive powered up and in use (3rd edit)_. The camera end of its USB cable contacted the mini-plug end of the mouse charger... could that have short-circuited the hub? +That wouldn't explain the failure of the GE hub a couple weeks before... but I don't know if any of this is connected, so to speak--2nd edit.+)
Message was edited by: blick
Message was edited by: blick
Message was edited by: blick

Question about interface for recording electric guitar and vocals

Ok, I've been messing around with Garageband all day, totally stoked and I'm ready to get into it. Right now I'm using a First Act quarter inch plug to USB cord to hook up my guitar and start recording and after some messing around I got it to work.
Here's my question... to really make quality recordings, what's the best way to hook up the guitar? Is the way I'm doing it now fine with the USB cord or is some sort of interface better? Can someone recommend one that's on the cheap side? Also, I haven't tried yet, but what's the best way to record vocals? Should I invest in a USB mic? Can anyone recommend one? I have a Shure SM58 already, what's the best way to hook that up?
Really excited about this, can't wait to start cranking out some songs!
PS: When I use the USB cord, I don't see any way to control the recording level, and sometimes I get a Feedback control warning. How can I lower the level so I don't get that? Thanks!
Message was edited by: xSlamx

I have a total now of 4 interfaces - I recently purchased a FOCUSRITE SAPPHIRE 6 USB - it's amazing quality and I only paid $149 for it at my local Guitar Center. I use it with my Guitar and everything sounds fantastic - they say the preamps are really high-quality for Mics too... I recommend it. I have a firewire interface too but the Sapphire is my man baby now - don't let the USB 1.1 fool you - it works flawlessly with my Mac and my Windows 7 machine too. It also comes with a selection of software including Ableton Live Lite and 4 really nice Focusrite plug-ins too.

A question about grub and USB

Hi All
I have a quick question about grub and USB that I can't quite find the answer to by searching. Most of the FAQs discuss booting a full linux dristribution from USB. My situation is this. I am getting a new computer with two drives, the second will be arch and the first will be Vista (for my wife). I want the computer to boot the same way that my wife's machine boots at work so I don't want to install grub on the MBR. So, is there a way to have all of the grub config files and kernels installed on the second drive and simply install to grub boot loader to the MBR of a USB stick? My goal would be to simply plug the USB stick into the new PC and boot arch from the second drive.
Thanks
Kev

i cant say for hp's
havent worked on any in a while
recent machines have been coupleof dell's , vaio & emachine
which dells do offer it at least the ones i tried , my laptop does(dell)
all home pc's are built by me which do offer to boot individual drives
what hp you getting it may tell in specs
are both discs sata? if so it might not offer this option with 2 drives of same interface
check your power supply alot of these preconfigured machines put cheap under reated power supplies in there
& will burn your motherboard i just replaced PS(250 watt) & mobo(845gvsr) in an emachines <cheap stuff<
i hope you researched the pc before buying ie : mobo, power supply are the biggest concerns
i find it much more benificial to build my own machine gives me peace at mind. the cost is sometimes more in $ but not always , your biggest expense is time researching hardware
if you live in usa the best places to start looking are bensbargains.net & pricewatch.com
i am not affiliated with either & niether sell the hardware they are just advertisers a place to buy
for costomized machines that i would trust is unitedmicro.com theyll asemble & test before shipping
i have gotten 2 machines so far from them with NO PROBLEMS with hardware (knock knock)
you may want to consider this in your next venture for pc

Bitlocker without TPM and USB

Hello Team,
I am working for a company which has Windows Server 2012 R2 domain server and mixture of Windows 7 and Windows 8 client computers.
The problem is, I need to configure bit-locker in all client machine, but some machine doesn't have TPM. I found a way to configure bit-locker without TPM, but it requires USB(key within it) at every startup.
So I want to configure Bit-locker in all client machine without TPM and USB, but with PIN. And all bit-locker recovery keys should be backed up to Active directory.
Please let me know the steps to configure this rather than HTTP links.
Thanks in Advance.
Have a great day ahead and make a great day for me.

Hi.
Having a PIN is only possible in combination with a TPM, but having a password alone is possible since windows 8.

Help required: Guitar to USB Lead cuts all sound

Hi, I'm having a small problem I'm hoping someone clever here might have a quick solution to:
I recently bought this Guitar to USB lead:
http://www.maplin.co.uk/Module.aspx?ModuleNo=225789
And plugged it into my MacBook after booting up Logic. The problem is that
when the lead is plugged in it cuts all sound from Logic - i.e. I cannot
hear any other tracks playing, nor indeed the guitar sound itself (but
other applications such as Safari do have sound). Logic is recognising the
lead's input, the levels go up when I strum the guitar and I can record the
guitar as audio into Logic. But I cannot hear the recorded guitar parts or
anything else until I remove the USB lead. Which makes the thing pretty
useless really...unless of course I'm being useless (a likely outcome).
So, can anyone supply a reason why plugging in this USB to guitar lead into
a Macbook with Logic is cutting all sound from Logic?
Thanks
(I bought this lead because I wanted a simple and cheap plug-and-play to connect my guitar to Logic - if someone has another solution for this then I'd also be interested in hearing that - thanks!)

I'm pretty sure an Aggregate device -WILL- work. In fact I know you have to use one.
Make sure your Aggregate device uses the Built-in audio OUT as the master clock device.
Also, If your USB guitar shows up as both an input and output device in aggregate setup -do not- include the output device newly created aggregate device.
pancenter-

DAQ vi to perform digital write and read measurements using 32 bits binary data saved in a file

Hi
DAQ vi to perform digital write and read measurements using 32 bits binary data saved in a file
Two main
sections:
1)
Perform
write and read operations to and fro different spread sheet files, such that
each file have a single row of 32bits different binary data (analogous to 1D
array) where the left most bit is the MSB. I don’t want to manually enter the
32 bits binary data, I want the data written or read just by opening a file
name saves with the intended data.
      2)
And
by using test patterns implemented using the digital pattern generator or build digital data functions or otherwise, I need to
ensure that the
            binary data written to a spreadsheet file or any supported file type
then through the NI-USB 6509 is same as the data read.
I’m aware I can’t use the simulated
device to read data written to any port but if the write part of the vi works I
‘m sure the read part will work on the physical device which I’ll buy later.
My Plan
of action
I’ve
created a basic write/read file task and a write/read DAQ task for NI USB 6509
and both combine in a while loop to form a progress VI which I’m confuse of how
to proceed with the implementation.
My
greatest problem is to link both together with the correct functions or operators
such that there are no syntax/execution errors and thus achieve my intended
result.
This
project is one of my many assignments for my master thesis, so please i’ll
appreciate every help as I’m not really efficient with LabVIEW programming but
I prefer it because is fun and interesting if I get to know it.
Currently I’m
practicing with LabVIEW 8.6/NI DAQmx 8.8 Demo versions and NI USB 6509
simulated device.
Please see
the attached file for my novice progress, thanks in
advance for the support
Rgds
Paul
Attachments:
DIO_write_read DAQ from file.vi ‏17 KB

What does your file look like? The DAQmx write is expecting a single U32 value, not an array of I64.
Message Edited by vt92 on 09-16-2009 02:42 PM
"There is a God shaped vacuum in the heart of every man which cannot be filled by any created thing, but only by God, the Creator, made known through Jesus." - Blaise Pascal

Please Read this ! USB Sound Blaster 24-Bit External : The Story of the endless problem

In order to keep the good behavior here (I`m really pissed off !) I just?want to tell you something (this is ESPECIALLY for all the guys from the stuff)?Before 2 days I`ve decided to buy a new sound system for my room. I bought myself Creative Inspire t600 5. surround system. Cool. I was very happy. I?needed only to buy a sound card?working with 5. because I have a notebook DELL INSPIRON 50 who has only 2 canals. So in order to be everything beautiful I gave $70 for Usb sound blaster 24-Bit external. And from that time the problems began. In short :? I was using Vista but I found out that it wont work with this soundcard. The first problem : Didn`t identify the device. I tried with several drivers... Nope. No sound card with Vista.(This problem seems to appearance with many owners like me)?I pluged the usb soundcard in my old pc running XP and it worked . PERFECTLY. So I removed Vista from my notebook and intalled XP. This took me whole day to rebuild all my software. Finally it left to set up the sound drivers. The cherry of the icecream. Aaaaand ..... **bleep**. When I play?any track it CRACKLES. Again problem appearanced with many here. I tried to find out here what is the problem but unfortunately as u can see my english is quite bad?so I cant understand?what I need.I really like Creative but if they cant manage this problem I will?no longer buy their stuffs??JUST PLEASE SOMEBODY ANSWER ME IS THERE ANY SOLUTION FOR THIS OR NOT. I JUST WANT STRAIGHT ANSWERPS : Please do not delete my post. I know there are plenty like this. I dont want this crackles

well ?

Guitar and USB SB Live! 24-bit Exter

Similar Messages

Maybe you are looking for