H535 Power Supply and Graphic Card
I have did a lot of internet research, but I cannot seem to find what I am looking for. I plan to upgrade the video card in my machine, H535-57323780, because I have the need for 3+ monitors. I have been considering a XFX-R7750 core edition to meet the video needs. But with that card, I need a power supply that is 450w+. Also, I'm not sure if that card will work or not because some of the posts have referenced using a "low-profile" card.
Any advice on as to whether the card will work or not and suggestions for the appropriate power supply will be greatly appreciated.
Hi,
Your choice for a PSU will fit but it doesn't meet the AMD system requirements which is 400 watts.
The ASUS AMD 6670 that you have referenced should fit but it's always best to open your PC for inspection and measurement.
This Corsair CX430 meets the minimum AMD recommended PSU wattage size and it's actually a bit cheaper due to the available rebate and shipping charge. All of the 12 volt amperage is on one rail so you will not have to worry about 12 volt rail balancing.
Review this posted document for background information.
These HP 'how-to" articles should be helpful.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT
Similar Messages
-
Power Supply and Graphics Card Question for HP Pavilion a6432p
Hello!
I have the HP Pavilion a6342p, and I'm wanting to install an NVIDIA Graphics Card either 512MB or 1GB. However, I'm not sure what is the power supply to this model (most graphics cards are saying 300-350W supply required).
Can anyone tell me what is the power supply to this model, and what would be a good graphics card model to look at to upgrade my graphics card to with this model? I believe the expansion slots are PCI-Express, but I'm not sure on the power supply so I can get the right graphics card.
Thanks!
NathanQuote
Originally posted by thegrommit
That 9100 doesn't even have a fan, correct? It should have no problem running on that motherboard with that PSU.
Also, the links in my sig may prove useful.
[edit] err, the 9100 is an integrated video chipset. Are you sure that's the correct number?
No the 9100 is not just an integrated video chipset and is available in both AGP & PCI form.
The Antec is a good PSU but I would recommend getting something better such as the OCZ or Enermax as they have a higher +12v rail amp. -
New power supply and graphic card for Compaq CQ3232L
Hi all,
I am using Compaq CQ3232L and would like to upgrade the graphic card with one of the HD 5770, Sapphire HD 5770 Vapor-X 1Gb 128Bit DDR5 to be exact.
My current power supply (Bestec Model ATX01...) specs are:
+12V/11A, peak 13A
+5V/10A, +3.3V/10A,
-12V/0.3A, 180W according the manual.
I've been looking a replacement for the power supply but not sure which one will fit the case? And how much power will be need to run the Sapphire card and future upgrade (Blu-Ray drive and another HDD)?
Regards,
EkoWSH, besides measuring the PSU, you should assure that there is sufficient space for the video card. Open the case. Measure from the edge of the case to the opposite side of the motherboard where the PCIE slot is located. This is the approximate length of the card that will fit.
Also, I like OCZ and Corsair PSU's. They are both enthusiast/gamer manufacturers. Their products will provide clean, stable power for your system.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee. -
Molex power supply for Graphics card uograde
I hav" a "late 2004" G5 2.0 dual processor. To upgrade graphics card, I find many require a power supply splitter. Do I have a molex 4-pin connector? I can't see the location inside the box.
You should have one on the optical drive. You'll need to get an Y-cable to allow you to hook into it.
-
No vga new viedo card,mother board,power supply and cable
persario sr550r no vga signal on monitor,new cable,new power supply,new viedo card,new mother board,still no vga signal,I have tested monitor it is good?Do you need to remove any viedo chip when installing new viedo card?I can rebuild a car from ground up!This computer is kicking my butt! help!!!
Terkemoma, welcome to the forum.
Don't let the computer KYB! We'll solve the problem.
First, however, I believe that there is another number in the model of the computer. Once I have the full model I will see what I can do to help you.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee. -
MDD power supply and fan upgrade kit question.
Hello, Its been a few years since I posted anything here and I'm getting ready to (possibly) trade in my mirror drive door 1GHZ dual processor machine on one of the current imac-s.
I'm not real hopeful that putting much work into my current machine is worth it. Here's why:
1) crazy levels of noise - I wear woodworking hearing protectors when I surf the web. Listening to music on itunes is fine so long as you like a background of low level blow dryer noise!
2) I'm still running OSX version 10.2.8, I have been too cheap to buy the latest OS. I'm tempted to go out and spend the $119 on 10.5 but I only have the original 256mb of ram installed and since the min requirement of ram is 512, I know I'll need to spend an extra ~50$ on a 512mb PC2700 ram chip. My price tag to do a minimal update is rising...
3) I would love to neutralize the noise and install the Apple provided MDD power supply and fan retrofit kit that they sent me at no charge several years ago while I was still under warranty. But I never did because the tech at my local (Dayton Ohio) reseller told me that the kit only addressed high noise levels when rebooting in OS9. So I never bothered. Looking on ebay, I see where power supplies for G4's could fetch 75 or 100$ or so.
In summary, here are my questions.
1) Has anything come along recently to tame MDD G4 fan noise that is easy to install, cost-effective and most of all, something that actually works to decrease the noise?
2) To get the quietest, quickest performance with the current OS 10.5 should I cut my losses now and trade (or sell on ebay) my MDD, sell the new power supply and just purchase a new machine with the OS already installed?
Thanks a bunch in advance for any assistance...
from Bill.Bill,
Carl has some pretty good points that I'd agree with - trying the replacement PSU and fans should quiet it down somewhat and replacing the stock main fan with a newer, quieter unit will also help. But I'm going to disagree with him on running Leopard on the G4's with a few reservations.
As you might notice from my profile, I'm running Leopard on my dual-867 MDD and find the performance acceptable; perhaps a little slower than Tiger in some respects but it does run well enough within the limitations of the G4's capabilities. The reservation I have about recommending Leopard on a G4 is the graphics card - without Core Image support (which you won't have unless you upgrade the video card) Leopard is going to tax the CPU more and may bog down in some tasks like Quick Look and Cover Flow.
In the end, whether to continue upgrading the G4 is a matter of use and economics. Tiger would be a fine upgrade with minimal cost and squeeze a few more years out of your G4 if you're not requiring software that needs an Intel CPU (like certain iLife '08 apps).
-Douggo -
Want to add Video and Graphic Card to my computer system
I Notice that one of the users' in the Apple discussion Board is Listed, (AndyO) he has help me many times in the Past and was succesful in my problrm solution, would he might be able to help me with this?
I had Purchased the Game Spore Creature Creator the Starter Kit which is just the Creature creator game and not the actual game itself. I wasn't able to install the the game on my computer because I don't have the right or not at all Video and Graphic Card install on my computer. I had Contacted the Company "EA" that puts out the Game Spore, this is what they said what the game requirements are: The minimum system requirements for Spore and Spore the Galactic Edition for Mac are as follows:
* Mac OS X 10.5.3 Leopard or higher
* Intel Core Duo Processor
* 1024 MB RAM
* At least 345 MB of hard drive space for installation, plus additional space for created creatures. (260 MB for the Trial Edition)
* Video Card - ATI X1600 or NVidia 7300 GT with 128 MB of Video RAM, or Intel Integrated GMA X3100
This game will not run on PowerPC (G3/G4/G5) based Mac systems (PowerMac).
For computers using built-in graphics chipsets, the game requires at least: an Intel Integrated Chipset GMA X3100 or Dual 2.0GHz CPUs, or 1.7GHz Core 2 Duo, or equivalent
Supported Video Cards
ATI Radeon(TM) series
* X1600, X1900, HD 2400, HD 2600
NVIDIA GeForce series
* 7300, 7600, 8600, 8800
Intel(R) Extreme Graphics
* GMA X3100
and that I need to upgrade my system. Basically I need; ATI Radeon 1600 or NVIDIA Geforce 7300 and a INTEL Extreme Graphic Video Card-GMA X3100, in order to be able to install and play this game. Since I already have this game, I would like to be able to upgrade my computer system which brings me to ask; does somone know or refer me to a web site that has and sells these Video and Graphic Card and supports for the Mini Mac?
Plus they say that I need a 1020 of MB of Ram, I Have already found that 1024 MB of Ram but I just need those Video and Graphic Cards for my computer system. I am adding my computer system Profile to my discussion board to show you what I have on my system, would you be able to tell me if I would be able to add these Video and Graphic card and the memory or Ram 1024 to my computer system?
Note: Here is a web site that I am looking at to add the 1024 MB of Ram to my computer system:
http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=24188 41&CatId=2453
what do you think?
Here is part a copy info of my computer system Profile:
Trisha Foster’s Mac mini
10/10/08 5:39 PM
Hardware:
Hardware Overview:
Model Name: Mac mini
Model Identifier: Macmini2,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 1 GB
Bus Speed: 667 MHz
Boot ROM Version: MM21.009A.B00
SMC Version: 1.19f2
Serial Number: YM8073Q**
Network:
AirPort:
Type: AirPort
Hardware: AirPort
BSD Device Name: en1
IPv4 Addresses: 169.254.247.182
IPv4:
Addresses: 169.254.247.182
Configuration Method: DHCP
Interface Name: en1
Subnet Masks: 255.255.0.0
IPv6:
Configuration Method: Automatic
Proxies:
Exceptions List: *.local, 169.254/16
FTP Passive Mode: Yes
Ethernet:
MAC Address: 00:1f:5b:3e:ce:93
Media Options:
Media Subtype: Auto Select
Bluetooth:
Type: PPP (PPPSerial)
Hardware: Modem
BSD Device Name: Bluetooth-Modem
IPv4:
Configuration Method: PPP
IPv6:
Configuration Method: Automatic
Proxies:
FTP Passive Mode: Yes
Ethernet:
Type: Ethernet
Hardware: Ethernet
BSD Device Name: en0
IPv4 Addresses: 192.168.1.102
IPv4:
Addresses: 192.168.1.102
Configuration Method: DHCP
Interface Name: en0
NetworkSignature: IPv4.Router=192.168.1.1;IPv4.RouterHardwareAddress=00:21:29:c3:12:ae
Router: 192.168.1.1
Subnet Masks: 255.255.255.0
IPv6:
Configuration Method: Automatic
DNS:
Domain Name: cruzio.com
Server Addresses: 74.220.64.45, 74.220.64.55
DHCP Server Responses:
Domain Name: cruzio.com
Domain Name Servers: 74.220.64.45,74.220.64.55
Lease Duration (seconds): 0
DHCP Message Type: 0x05
Routers: 192.168.1.1
Server Identifier: 192.168.1.1
Subnet Mask: 255.255.255.0
Proxies:
Exceptions List: *.local, 169.254/16
FTP Passive Mode: Yes
Ethernet:
MAC Address: 00:16:cb:af:11:7f
Media Options: Full Duplex, flow-control
Media Subtype: 100baseTX
FireWire:
Type: FireWire
Hardware: FireWire
BSD Device Name: fw0
IPv4:
Configuration Method: DHCP
IPv6:
Configuration Method: Automatic
Proxies:
Exceptions List: *.local, 169.254/16
FTP Passive Mode: Yes
Ethernet:
MAC Address: 00:1f:5b:ff:fe:17:17:2a
Media Options: Full Duplex
Media Subtype: Auto Select
Software:
System Software Overview:
System Version: Mac OS X 10.5.5 (9F33)
Kernel Version: Darwin 9.5.0
Boot Volume: Macintosh HD
Boot Mode: Normal
Computer Name: Trisha Foster’s Mac mini
User Name: Trisha Foster (tiger)
Time since boot: 59 minutes
ATA:
ATA Bus:
PIONEER DVD-RW DVR-K06:
Capacity: 423.4 MB
Model: PIONEER DVD-RW DVR-K06
Revision: Q614
Removable Media: Yes
Detachable Drive: No
BSD Name: disk2
Protocol: ATAPI
Unit Number: 0
Socket Type: Internal
Low Power Polling: Yes
Mac OS 9 Drivers: No
Partition Map Type: Unknown
S.M.A.R.T. status: Not Supported
Volumes:
SPORE:
Capacity: 368.7 MB
Media Type: CD-ROM
Writable: No
File System: ISO Rockridge
BSD Name: disk2s0
Mount Point: /Volumes/SPORE
Audio (Built In):
Intel High Definition Audio:
Device ID: 0x83847680
Audio ID: 8
Available Devices:
Headphone:
Connection: Combo
Speaker:
Connection: Internal
Line In:
Connection: Combo
S/P-DIF Out:
Connection: Combo
S/P-DIF In:
Connection: Combo
Bluetooth:
Apple Bluetooth Software Version: 2.1.0f17
Hardware Settings:
Trisha Foster’s Mac mini:
Address: 00-1f-5b-72-12-aa
Manufacturer: Cambridge Silicon Radio
Firmware Version: 3.1965 (3.1965)
Bluetooth Power: On
Discoverable: Yes
HCI Version: 3 ($3)
HCI Revision: 1965 ($7ad)
LMP Version: 3 ($3)
LMP Subversion: 1965 ($7ad)
Device Type (Major): Computer
Device Type (Complete): Macintosh Desktop
Composite Class Of Device: 3154180 ($302104)
Device Class (Major): 1 ($1)
Device Class (Minor): 1 ($1)
Service Class: 385 ($181)
Requires Authentication: No
Services:
Bluetooth File Transfer:
Folder other devices can browse: ~/Public
Requires Authentication: Yes
State: Enabled
Bluetooth File Exchange:
Folder for accepted items: ~/Downloads
Requires Authentication: No
When other items are accepted: Ask
When PIM items are accepted: Ask
When receiving items: Prompt for each file
State: Enabled
Incoming Serial Ports:
Serial Port 1:
Name: Bluetooth-PDA-Sync
RFCOMM Channel: 3
Requires Authentication: No
Outgoing Serial Ports:
Serial Port 1:
Address:
Name: Bluetooth-Modem
RFCOMM Channel: 0
Requires Authentication: No
Diagnostics:
Power On Self-Test:
Last Run: 10/10/08 4:41 PM
Result: Passed
Disc Burning:
TEAC CD-W540E:
Firmware Revision: 1.0F
Interconnect: FireWire
Burn Support: Yes (Apple Supported Drive)
Cache: 8192 KB
Reads DVD: No
CD-Write: -R, -RW
Write Strategies: CD-TAO, CD-SAO, CD-Raw
Media: Insert media and refresh to show available burn speeds
PIONEER DVD-RW DVR-K06:
Firmware Revision: Q614
Interconnect: ATAPI
Burn Support: Yes (Apple Shipping Drive)
Cache: 2000 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -R DL, -RW, +R, +R DL, +RW
Write Strategies: CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media:
Type: CD-ROM
Blank: No
Erasable: No
Overwritable: No
Appendable: No
FireWire:
FireWire Bus:
Maximum Speed: Up to 400 Mb/sec
OXFORD IDE Device LUN 0:
Manufacturer: Oxford Semiconductor Ltd.
Model: 0x42A258
GUID: 0x1D200500648AF
Maximum Speed: Up to 400 Mb/sec
Connection Speed: Up to 400 Mb/sec
Sub-units:
OXFORD IDE Device LUN 0 Unit:
Unit Software Version: 0x10483
Unit Spec ID: 0x609E
Firmware Revision: 0x444133
Product Revision Level: 1.0F
Sub-units:
OXFORD IDE Device LUN 0 SBP-LUN:
Graphics/Displays:
Intel GMA 950:
Chipset Model: GMA 950
Type: Display
Bus: Built-In
VRAM (Total): 64 MB of shared system memory
Vendor: Intel (0x8086)
Device ID: 0x27a2
Revision ID: 0x0003
Displays:
L1916HW:
Resolution: 1280 x 800 @ 60 Hz
Depth: 32-bit Color
Core Image: Hardware Accelerated
Main Display: Yes
Mirror: Off
Online: Yes
Quartz Extreme: Supported
Rotation: Supported
Memory:
BANK 0/DIMM0:
Size: 512 MB
Type: DDR2 SDRAM
Speed: 667 MHz
Status: OK
Manufacturer: 0xAD00000000000000
Part Number: 0x48594D503536345336344350362D59352020
Serial Number: 0x0000**
BANK 1/DIMM1:
Size: 512 MB
Type: DDR2 SDRAM
Speed: 667 MHz
Status: OK
Manufacturer: 0xAD00000000000000
Part Number: 0x48594D503536345336344350362D59352020
Serial Number: 0x00001*
Power:
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Sleep On Power Button: Yes
Automatic Restart On Power Loss: No
Wake On LAN: Yes
Hardware Configuration:
UPS Installed: No
Printers:
Canon MP830:
Status: Idle
Print Server: Local
Driver Version: 4.8.3
Default: Yes
URI: usb://Canon/MP830?serial=19702D
PPD: Canon MP830
PPD File Version: 1.0
PostScript Version: (3011.104) 0
Serial-ATA:
Intel ICH7-M AHCI:
Vendor: Intel
Product: ICH7-M AHCI
Speed: 1.5 Gigabit
Description: AHCI Version 1.10 Supported
Hitachi HTS541612J9SA00:
Capacity: 111.79 GB
Model: Hitachi HTS541612J9SA00
Revision: SBDAC7MP
Serial Number: SB2EF9L7G3**
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Mac OS 9 Drivers: No
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
Macintosh HD:
Capacity: 111.47 GB
Available: 63.14 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s2
Mount Point: /
USB:
USB High-Speed Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBEHCI
PCI Device ID: 0x27cc
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0xfd
Keyboard Hub:
Version: 94.15
Bus Power (mA): 500
Speed: Up to 480 Mb/sec
Manufacturer: Apple, Inc.
Product ID: 0x1006
Serial Number: 000000000000
Vendor ID: 0x05ac (Apple Computer, Inc.)
USB RECEIVER:
Version: 25.10
Bus Power (mA): 100
Speed: Up to 1.5 Mb/sec
Manufacturer: Logitech
Product ID: 0xc50e
Vendor ID: 0x046d
Apple Keyboard:
Version: 0.69
Bus Power (mA): 100
Speed: Up to 1.5 Mb/sec
Manufacturer: Apple, Inc
Product ID: 0x0220
Vendor ID: 0x05ac (Apple Computer, Inc.)
iPod:
Version: 0.01
Bus Power (mA): 500
Speed: Up to 480 Mb/sec
Manufacturer: Apple Inc.
Product ID: 0x1291
Serial Number: aa1186ca1738fd28eef1eeb1b22754********
Vendor ID: 0x05ac (Apple Computer, Inc.)
USB2.0 Hub:
Version: 7.02
Bus Power (mA): 500
Speed: Up to 480 Mb/sec
Product ID: 0x0606
Vendor ID: 0x05e3
USB 2.0 3.5" DEVICE:
Capacity: 153.39 GB
Removable Media: Yes
Detachable Drive: Yes
BSD Name: disk1
Version: 0.01
Bus Power (mA): 500
Speed: Up to 480 Mb/sec
Manufacturer: Macpower Technology Co.LTD.
Mac OS 9 Drivers: Yes
Partition Map Type: APM (Apple Partition Map)
Product ID: 0x0073
Serial Number: BC0*
S.M.A.R.T. status: Not Supported
Vendor ID: 0x0dc4
Volumes:
miniStack:
Capacity: 153.26 GB
Available: 42.96 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk1s10
Mount Point: /Volumes/miniStack
MP830:
Version: 1.15
Bus Power (mA): 500
Speed: Up to 480 Mb/sec
Manufacturer: Canon
Product ID: 0x1713
Serial Number: 197*
Vendor ID: 0x04a9
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBUHCI
PCI Device ID: 0x27c8
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0x1d
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBUHCI
PCI Device ID: 0x27c9
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0x3d
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBUHCI
PCI Device ID: 0x27ca
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0x5d
USB Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBUHCI
PCI Device ID: 0x27cb
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0x7d
Bluetooth USB Host Controller:
Version: 19.65
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Apple, Inc.
Product ID: 0x8205
Vendor ID: 0x05ac (Apple Computer, Inc.)
IR Receiver:
Version: 1.10
Bus Power (mA): 500
Speed: Up to 12 Mb/sec
Manufacturer: Apple Computer, Inc.
Product ID: 0x8240
Vendor ID: 0x05ac (Apple Computer, Inc.)
AirPort Card:
AirPort Card Information:
Wireless Card Type: AirPort Extreme (0x168C, 0x86)
Wireless Card Locale: USA
Wireless Card Firmware Version: 1.4.4
Current Wireless Network: Trisha's iPod
Wireless Channel: 11
Firewall:
Firewall Settings:
Mode: Allow all incoming connections
Locations:
Automatic:
Active Location: Yes
Services:
AirPort:
Type: IEEE80211
BSD Device Name: en1
Hardware (MAC) Address: 00:1f:5b:3e:ce:93
IPv4:
Configuration Method: DHCP
IPv6:
Configuration Method: Automatic
AppleTalk:
Configuration Method: Node
Proxies:
Exceptions List: *.local, 169.254/16
FTP Passive Mode: Yes
IEEE80211:
Join Mode: Automatic
JoinModeFallback: Prompt
PowerEnabled: 1
PreferredNetworks:
SecurityType: Open
SSID_STR: Apple Store
Unique Network ID: 4BCBEE2D-83B9-4CC1-B110-8D0E8E5DF49C
SecurityType: Open
SSID_STR: linksys
Unique Network ID: F2551FD6-95A7-4F98-9F7F-758A89DBD931
Bluetooth:
Type: PPP
IPv4:
Configuration Method: PPP
IPv6:
Configuration Method: Automatic
Proxies:
FTP Passive Mode: Yes
PPP:
ACSP Enabled: No
Display Terminal Window: No
Redial Count: 1
Redial Enabled: Yes
Redial Interval: 5
Use Terminal Script: No
Dial On Demand: No
Disconnect On Fast User Switch: Yes
Disconnect On Idle: Yes
Disconnect On Idle Time: 600
Disconnect On Logout: Yes
Disconnect On Sleep: Yes
Idle Reminder: No
Idle Reminder Time: 1800
IPCP Compression VJ: Yes
LCP Echo Enabled: No
LCP Echo Failure: 4
LCP Echo Interval: 10
Log File: /var/log/ppp.log
Verbose Logging: No
Ethernet:
Type: Ethernet
BSD Device Name: en0
Hardware (MAC) Address: 00:16:cb:af:11:7f
IPv4:
Configuration Method: DHCP
IPv6:
Configuration Method: Automatic
AppleTalk:
Configuration Method: Node
Proxies:
Exceptions List: *.local, 169.254/16
FTP Passive Mode: Yes
FireWire:
Type: FireWire
BSD Device Name: fw0
Hardware (MAC) Address: 00:1f:5b:ff:fe:17:17:2a
IPv4:
Configuration Method: DHCP
IPv6:
Configuration Method: Automatic
Proxies:
Exceptions List: *.local, 169.254/16
Can someone Please help me with any suggestions or otherwisde I will have to go to a Apple store and ask for help there.
Thank You,
Trisha Foster
<Edited by Moderator>Hi Trisha,
The only modern Mac's with video cards are the Mac Pro and Xserve (server) systems. They both are priced quite a bit higher than any Mac Mini.
Some systems, like the Mac Book Pro laptop can be ordered with different graphics cards, but that has be done when the system is built, as it is not replaceable once the system is built. To find out which systems, go to store.apple.com. For each system that you select, you can see if there's an option for a better video card.
David -
Severe Incompatibility between Mac Pro 2012 power supply and Tripp Lite LC2400 [switching transformer].
The Mac Pro will not power on when connected to the Tripp Lite LC2400. The Power Supply makes continuous clicking noises and repeatedly resets the Mac Pro every 3 seconds.
The same Mac Pro connected to an outlet with no Tripp Lite starts up with no problem.Hi,
I've the same notebook. I've not had any hardlocks so far, but I've not seen so much flash movies yet. Anyway, I just tried closing running youtube-video tab on Kde4 + enabled desktop effects -> Everything's fine.
Anyway, perhaps we can collect some issues and solutions in this thread. Here are problems, that I encounter:
- restart does not work
- errors during boot:
[ 2.399277] pnp 00:0b: [irq 23]
[ 2.399308] pnp 00:0b: Plug and Play ACPI device, IDs SMO8800 (active)
[ 2.932179] pnp 00:0c: can't evaluate _CRS: 12311
[ 14.616662] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 14.616771] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 14.616792] iTCO_wdt: cannot register miscdev on minor=130 (err=-16)
[ 14.616904] iTCO_wdt: probe of iTCO_wdt failed with error -16
[ 9.262898] sdhci-pci 0000:0b:00.1: SDHCI controller found [1217:8321] (rev 5)
[ 9.262920] sdhci-pci 0000:0b:00.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 9.262966] sdhci-pci 0000:0b:00.1: Invalid iomem size. You may experience problems.
[ 9.263176] sdhci-pci 0000:0b:00.1: setting latency timer to 64
Issued solved:
- in order to make nvidia graphics working you have to disable Optimius in BIOS.
- Battery not recognized -- fixed after recend updates
- grub2 does not work. As soon as grub2 loads, the laptop reboots. -> stick to grub1 -- works now (either I did sth wrong the first time or a new version of grub2 fixes this issue)
- in order to make the touchpad work properly install psmouse-elantech from AUR
update: this is only a half-solution. vertical scrolling on the right edge works but graphical tools which rely on x11-input-synpatics still don't work. However, everything works fine with kernel 3.3. Once this in the main arch repos you won't need psmouse-elantech anymore.
Last edited by knue (2012-03-06 23:26:26) -
What is maximum temperature for hard disk and graphics card?
After an hour of running mac, it gets so slow that after a while, i have no choice but to switch off with power key (pressed for 10 secs or so).
I downloaded temperature monitor gadget and I am noticing harddisk and graphics card temperature going high from 84 F to 130+ F
Is there any specifications on temperature range for different devices of iMac 24, 2007 model?psachania wrote:
Is there any specifications on temperature range for different devices of iMac
24, 2007 model?
Apple does not provide this information. Though the hard drive details can be looked up at the manufacture website. Most consumer grade drives have a maximum operating temperature of 60C. Though heat can play into lifespan of the drive so I would not want the drive running anywhere near that for extended periods. My advice is to keep the hard drive under 50C.
What applications you are running? How much RAM do you have? and how much free space is left on your hard drive?
George -
Recommend compatible PSU and graphics card for P35D3?
Recommend compatible PSU and graphics card for P35D3?
This weekend I’ll be taking my rig to a PC repair shop and ask them to swap out my PSU and my graphics card.
Because I’ve RMA’d all the components (see signature) several members of different forums, and the tech support of the various components, seem to think that my boot problem is because of a compatibility issue with either my Ultra X3 600W PSU or my XFX 8600 GT and my P35D3.
I need to be ready to make decision, without having time to research, if the repair tech recommends a replacement.
Here’s my considerations:
I selected the Ultra because it's both modular and 85% efficient (it also has the required 8-pin cable to power the P35D3's CPU and it has SATA power cables.
I selected the XFX 8600 GT card because it is dual-link (2 DVI outs -- Dell 30” & Viewsonic 19”) and it has no fan, and is DX10 ready. I’m not attached to the idea of no fan. I’m a speed freak but not a gamer or an over clocker--I like the option of trying out games.
Both the Ultra and the XFX are somewhat medium priced.
If the repair tech discovers that other PSUs or graphic cards work then I might be able to get Ultra or XFX to accept a return. Neither company accepted my offer to pay extra to exchange mine for another better model.
Suggestions please.
Thank you,
KerryThanks Boss,
Quote
Look here for good PSU suggestions:
https://forum-en.msi.com/index.php?topic=112039.msg836246#msg836246
About VGA any should work, you can see MSI Test Report for your board here:
http://global.msi.com.tw/index.php?func=prodtestreport&prod_no=1230&maincat_no=1&cat2_no=&cat3_no=#menu
lots of good info.
Wish me luck today (Thu), that the tech finds out my XFX or Ultra is not compatible.
Kerry -
Solution for monitor power supply and raid 5 on x4150 server
Hi everybody,
a simple question :
my compagny have some server SunFire x4150 in some Datacenter, and there is a thing that we cannot really monitored remotly : the status of the 2 power supply and the status of the raid 5 of the server.
(i want to know if a power is down or if a disk is "dead")
We are using Nagios, cacti and munin actually, so can we use these interfaces for that?
if the answer is no, a script can be developed , if only i knew the command that can be used to take informations from the state of the raid5, i'll comunicate later the type of the raid card.
what are the best solutions availables for monitor those things?
thanks by advanceWe have some x4150s but they're running Linux. There are separate solutions for each of the 2 problems.
1. For the power supplies, you can use the ELOM/ILOM system management interface (also used for monitoring the fans and temperature). If you've got it configured and connected to the network, you can set it up to email you about any events. We have the older ELOM firmware running, which includes the ability to add some actions to take in response to specific events. The new and supposedly better ILOM firmware doesn't seem to include this. Since this is IPMI compatible you can probably also hook into this using ipmitool or SNMP tools.
2. For the RAID card, assuming it's the standard Adaptec (rebranded as StorageTek) controller, you can install and use StorMan software (it's on the tools & drivers CD if not pre-installed). Once again you can configure email notification from the StorMan GUI, but this time it relies on OS host services to do the mail forwarding via the host NIC.
I'm not familiar with the details of your network system admin tools, but hopefully these tips will provide pointers on what hooks are available for these tools to tie into. Presumably there's also Sun N1 management software which can probably do this in a more built-in way, but it sounds like you've already got more than enough management tools. -
NX6800GT-T2D256E, Power supply and 6-pin connector
My NX6800GT-T2D256E came with a power adapter: 2x 4-pin Molex to a 6-pin connector that goes into the VGA-Card.
I've noticed that I have an identical 6-pin connector directly on my power supply (a Cieftec GPS-400AA-101A)
According to the power supply's manual, it is a PCI power connector, seemingly for powering PCI-express VGA cards.
Of course I want to use that connector, as it seems to be the ideal way of powering the card, but first I compared the pin configuration to make sure it is the same thing - and found a slight difference.
On the Adapter supplied with the card, 1 of the pins is empty (not connected) while on the connector from my power supply it is connected to +12V
Basically the pin configuration looks like this:
1 4
2 5
3 6
On the adapter supplied with the card they are:
1: +12V
2: NOT CONNECTED
3: +12V
4: Ground
5: Ground
6: Ground
On the power supply they are:
1: +12V
2: +12V
3: +12V
4: Ground
5: Ground
6: Ground
Can I safely use the connector from my power supply or could the additional +12V damage my VGA card?Your PC has a standard ATX power supply and physical sizes will vary slightly. You might want to measure the dimensions of your power supply. Normally the standard ATX PSU will measure 5.9" by 5.5" by 3.4". You don't want to get too far away from the dimensions of your PSU since the HP mini-tower cabinets are very tight inside. I prefer the modular model PSUs to help with excess cabling issues. www.newegg.com has many good brands. Not all PSUs are created equal. Look at the warranty period, amperage on the 12+ volt bus, specification level, i7 support, efficiency rating etc..
OCZ, Enermax, Corsair and Rosewill are all good brands as is Thermaltake.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT -
The Crew –Racing with Your Coolest MSI Gaming Motherboard and Graphics Card
Most gaming fans are crazy about racing games, and there is a new game title just launched to fulfill gamers’ dream. We want to share with you the experience from Taiwan user who assembles a rig with a brand new MSI Z97 Gaming 5 motherboard and 960 graphics card, along with a hardware and game (The Crew) benchmarks. You may find the original article from:
https://forum-tc.msi.com/index.php?topic=113352.0
The Crew - Launch Trailer
PC configuration:
CPU: Intel i5-4670K
RAM: Avexir DDR3-1600 8G*2
VGA: MSI GTX960 GAMING 2G
SSD: Kingston HyberX 3K SSD 240G
CPU Cooler: SilverStone AR01
The MSI Z97 Gaming 5 motherboard box
Overview of the motherboard: Black and Red color scheme, it’s also the favorite color combination from MSI’s user reservation.
The PCI-E slots and bandwidth are enough for a two-way SLI setting.
Killer Ethernet, outstanding performance on internet access, especially reduce the lag issue.
The new arrival MSI GTX960 GAMING 2G graphics card
New cooling design: ZeroFrozr
The dragon symbol on LED panel
With MSI Gaming series motherboard plus graphics card, you can enable a Gaming App to overclock CPU and GPU. There are 3 modes to choose.
6-month free trail of the XSplit game caster software, free bundled with MSI gaming motherboard and graphics card
Done with assembling, quiet nice color combination and clean cable arrangement.
An overview of the very gaming look system.
Some benchmark results before racing with The Crew.
CPU and GPU info on CPU-Z and GPU-Z applications:
3DMark Fire Strike score: 6441
3DMark Fire Strike Extreme score: 3384
3DMark Fire Strike Ultra score:1262
The excel performance proof the brand new 960 graphics card comes with good a high Cost/Performance Value.
Now, check out this test benchmark score of the renowned game “The Crew”.
The game presents an ultra-quality display, 60 Frames Per Second (FPS)
FPS: Average frames is at:
Frames: 3859 - Time: 76828ms - Avg: 50.229 - Min: 43 - Max: 56
The comments of the game for your reference:
There are many types of missions that can be chosen from the America’s map.
Street racing, high-speed collision, breakaway from police, sky jumps, zigzagging, etc… make the game quite dynamic.
Now, when it comes to multi-player matches, the performance has exceeded expectations. Perhaps, it is the killer Ethernet that’s working the magic. Thus, this game is highly recommended if you have the right rig.
The downside is that the display intricacy is not as refined as GTA V and in addition, the game FPS is limited at 60 FPS. However, the overall gaming flow and performance is better than good.
The user's comment for using MSI Gaming 5 motherboard and 960 graphics card:
(The following commends are translated from user’s article, does not represent the viewpoint of MSI) ^^
Recently, MSI GTX 960 just launched so the initial price tag is still adjustable.
According to the current product line, it seems like this GPU is going to replace 750Ti. So once all the stocks (750Ti) at the store empties, we are most likely to see a price drop on GTX960.
Once the price hits the sweet spot, it’s time to try out GTX960 SLI’s performance.
The CP value on MSI GTX960 and GAMING 5 MB is pretty high. But the XSplit software that comes with the product is a bit annoying since the authentication steps are divided into 2 parts to go through for using it.
Enough said, anyways, GAME ON!NVIDIA 960 card + GAMING 5 motherboard = best bundle for budget gaming!
it would be nice to see more testing of hardware-demanding games! -
Processor and graphics card upgrade for hp dc5100 MT(EF633US)
Can someone kindly tell me a variety of Intel processors and graphic cards which i can install in my pc coz right now i'm using Intel pentium 4 CPU 2.80 GHz and Intel 82915G/GV/910GL express chipset. but i would like to upgrade to a faster processor and a graphics card which can play games which require large graphic memory (eg FIFA 2013,GTA 5.etc)
Hi:
Personally, I wouldn't invest the money to upgrade that PC.
You would be better off getting an off lease newer dc5800 MT or dc7800/dc7900 model that has a PCIe x16 video slot.
The killer for your model is you can only install a PCI graphics card.
Very inefficient and pretty expensive for what you get in return.
After you install the required microcode update, the best processor I know for sure you can install would be the P4 650.
Below is the link to the quickspecs. The supported processors are listed on page 7.
I do not know of anyone who that has installed the 651 or 661 processors and got them to work--even though the specs state they are supported.
You can try the 651 or 661 and if you do, please let me know if they worked for you.
http://h18000.www1.hp.com/products/quickspecs/12145_ca/12145_ca.pdf -
I am using an Agilent Power Supply to apply a voltage to a
thermistor to heat an Al chassis. I want to use LabVIEW to tell
the power supply to apply 5V for 10 minutes, then step to 7V for 10
minutes, etc. I am completely new to LabVIEW, so any help would be greatly appreciated!
In addition to that, I want to place a type J thermocouple onto the Al
surface and use a Keithley 2000 DMM to monitor the temperature (it has
a built in conversion from V to Temp for type J). I will also be
using another Kelthley 2000 DMM to record the output voltage of a new
uncalibrated thermocouple. I would like to collect the output
voltage for this uncalibrated thermocouple and the temperature reading
from the type J simultaneously. How should I go about doing this
in LabVIEW? I will be using version 6.1. The power supply
and DMMs will be connected to a PC using GPIB.
Again any suggestions would be greatly appreciated- I have no idea
where to begin on such a project. I have taught myself how to
make a basic VI- converting temp in oC to oF, but that is as far
as my knowledge goes.What you want to do should be fairly straightward and a good way to learn labview.
First off, if you haven't already, I would download the drivers for the Keithley and Agilent instruments. I found the keithley drivers at the link below. You will need to find the labview drivers for the Agilent PS at their website. Drivers are the VI's you will use in your program to control the insturments.
http://sine.ni.com/apps/we/niid_web_display.download_page?p_id_guid=E3B19B3E90B0659CE034080020E74861
If you open Labview and go to the help menu and click on Labview bookshelf there is alot of information on getting you started coding labview. This should get you started, if you have anymore questions just ask in this same thread and I am sure you will get all the help you need.
Brian
Message Edited by BrianPack on 09-14-2005 05:21 PM
Message Edited by BrianPack on 09-14-2005 05:21 PM
Maybe you are looking for
-
Font problem with Openoffice 3
This image shows the problem, its KDE ina virtual Machines (Currently on ubuntu and testing arch for a near-future change and real installation) Can anyone help me? Last edited by Xi0N (2008-12-01 20:44:00)
-
How to make NetBoot images appear in the option boot screen?
So I have a NetBoot server. Yay! Everything works great, but I want certain images to appear when you option boot the machine. Is this possible?
-
Photoshop Not Saving Due to Program Error
Just had a user unable to save a document. Didn't matter is it was to a local HD, server or even a USB Thumbdrive. We traced it down to a single Hue Saturation adjustment layer and layer mask. Once removed, the document saved. Any ideas on what could
-
Chess.app runs OK on my MacBookPro under OS 10.6.8. Under the same OS on my Mac Pro Chess.app will not show the hint for the next move. The detail on the desktop MacPro is Model Name: Mac Pro Model Identifier: MacPro1,1 Processor Name:
-
Create or crop an .swf at runtime?
hello, if i have a .swf with some graphics created on it (dynamic shapes, text...) and it's dimensions are, say 300x300, would it be possible to have an event which would "crop" it to say 100x100 based on coordinates entered? furthermore, would it be