H55M-E23 low sound quality

Hello.I have this serious problem with my sound card.I have these rly awesome headphones and when i listen music the quality of the songs is realy low.I used the same headphones on my brother's laptop and the difference is amazing...... i can hear every instrument used in the recording of the song.While im on my own its super normal even low quality.I wana know guys is there a way to improve my quality with codecs or something else.I already downloaded the latest driver and its still the same.Is there anyway or should i buy a new and better sound card.Hope to hear from you soon.Thank you.

Did you try disconnecting the front connectors and see if it sounds better?
Try plugging the comp into a different room. *Perhaps the ground on that circuit of the house is messed up
Perhaps even remove the motherboard and put it on a piece of cardboard and test it there. *make sure there are no shorts
Has it always been like this, or is this new?
Is everything else working 100% with the comp?
You could check the memory with: >>Memtest86<< although I don't think thats the issue.
*other things that can cause.
1.)Software Issue or conflict (I usually just re-install the OS to rule this out)
2.) Interferance from another electrical applicance too close to the computer.
3.) bad electrical ground
4.) Hardware Failure

Similar Messages

TECRA A11 - low sound quality earphone to AUX

Tecra A11 provides *low sound quality* (iTunes) connecting with my hifi system *via earphone out to AUX* in. An Apple MacBook connected in the same way does much better. Any idea how could enhance the quality? Thanks in advance!

Hmmmmm...... have you tried to change sound settings, player equaliser?
Open control panel and check if there is Realtek sound manager (Realtek soundcard) and play a little bit with sound effects settings.

Fuzzy low sound quality with AirTunes

AirTunes sound quality sounds like a put a pillow over my speakers and its very fuzzy. I have no idea what could be wrong. Any thoughts?
And it has a good connection so that isnt the problem.

I asked the Apple WM guy if the AX Toslink digital signal could be sent to an outboard DAC ...and he said, no, it's an analog (music) signal, and then basically gave a disclaimer that Apple doesn't support any other uses for it. (???)
Huh? No. The Toslink is optically coupled digital data. It's the same data supplied to the Express's built-in DAC. The DAC's output is analog. Toslink (or the generic name digital optical audio) is commonplace with audio equipment.
http://www.toshiba.com/taec/components/ProdLineGuide/toslink.pdf
Apple's own specifications say the Express has a "3.5-mm audio minijack for analog *or optical digital sound*". The Einstein you spoke to doesn't understand his own product. Ask to speak to someone who does.
You could easily modulate an analog signal and transmit it over optical fiber using the same inexpensive plastic fiber optics that Toslink uses, and subsequently demodulate and amplify the received optical signal. I did that in grade school. But that does not describe the Express's optical output, which is strictly a digital signal.
Perhaps this product would interest you?
http://www.audiocubes.com/product/Audio-TechnicaAT-HA25D_HeadphoneAmp.html
Here's another:
http://www.audio-technica.com.sg/products/headphones/at-dha3000
Message was edited by: John Galt

Z1 Compact headphone low sound quality

hello , after i upgraded to loliop i started to have problems with my headphones MH750 , the sound quality became variant und bad , i have tried to change the clear audio+ and dynamic normaliser but not much to mention , any solutions ? thanx in advanced

I have the same issue with audio output on my z1. It is completely random, sometimes the bass will be almost non existent until i restart the walkman app a few times until the bass is there. Sometimes channeling through the headphone types will bring the bass back in, sometimes not. It's a complete pain and unpredictable.

Lower sound quality / lower bass after upgrade to Windows 8

Hello, just upgraded to Windows 8 on my Pavilion m7.
Before, my audio quality was rich and bassy, using Beats Audio, and after the upgrade sounds poor and quite muted. No matter what I do, I cannot improve quality especially with the deep bass. I am using external speakers, not the ones built in laptop.
In order to troubleshoot, I did a factory restore back to Windows 7... sounded fantastic. When I redid a clean 8 install on top of that, back to the same lack of bass.
Has anybody else experienced something like this?

Hi Zerxiisiis,
Sorry to hear about your audio issue during the upgrade. I will be happy to assist you with that. There are a couple of things that you can try. The first is uninstalling your current audio driver. Uninstall it through device manager.
http://msdn.microsoft.com/en-us/library/windows/hardware/ff553572(v=vs.85).aspx
Then download and install your audio driver again. I have included the link below.
http://msdn.microsoft.com/en-us/library/windows/hardware/ff553572(v=vs.85).aspx
If that doesn't work you might just need to adjust your equalizer settings for your Beats Audio. I have included a link to a thread where a user has posted some good levels.
http://h30434.www3.hp.com/t5/Notebook-PC-Sound-and-Audio/Beats-Audio-EQ-Setting-General-Sound-Advice...
Let me know how it goes.
Thank you!
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

HT204387 iPhone 6+ A2DP implementation and blutooth sound quality

My iPhone 6+ plays over blutooth to volkswagen RNS810 media system with much lower sound quality than CDs or even AAC. Normally I cannot tell the difference between AAC and CD in my car. Does the A2DP implementation here send AAC files from iPhone to RNS810 or there is some other re-compression going on on the way ? Also no titles show on the RNS810 screen. How to get best sound quality here and see track information on RNS810 screen? TIA.

I had the same problem on my 4s after the update. I rebooted phone and all is well.
Hope this works for you.......

Issues with sound quality after moving library to external HD

after i moved my itunes library to an external HD, the sound quality of the music files (both imported from CDs and itunes purchases) developed significant hissing and crackling and slight pitch shifts.
even after i switched back to using the internal itunes library, the low sound quality persisted.
is there some sort of an audio setting that needs to be changed? is this an itunes issue or something related to the HD? please help.
here's some info on my set up:
new HD: fantom g-force 500gb usb 2.0
mac mini: 1.42 ghz powerpc g4/1gb memory/80 gig internal HD
itunes: 7.6.2
quicktime: 7.5

go what I needed from a fellow mac user

MDR-ZX100 sound results not same as bundles headset sound quality

Hi guys, could you help me, how can MDR-ZX100 headset produce the same quality of sound as the bundled headset of xperia z1? The sound quality of MDR-ZX100 produces low sound quality including the bass... Could an adapter solve the problem?

its because the z1 3.5 aux port does not give high voltage that is the reason for low noise xda dev have found the solution but dont know why sony isint giving us a proper software in the firmware
this is the link but for this u have to root the phone
http://www.xda-developers.com/android/increase-the-volume-on-the-sony-xperia-z1/

Why such sorry sound quality on iTunes? On some of my purchases the sound level is suppressed on the audio. On others the volume is so low that if I have it set for another song and a new one starts I have to increase the volume to hear it.

Why such sorry sound quality on iTunes? On some of my purchases the sound level is suppressed on the audio. On others the volume is so low that if I have it set for another song and a new one starts I have to increase the volume to hear it.
There is so much distortion on some of the music I have to play it with QuickTime to get a "clean" track.
What can be done to get a consistent volume level or is this another typical Apple product that you have to take what you get and be happy because it's not a Microsoft product?

If that's the best you can do why don't you get on another forum?

HT1481 My ipod's sound quality has changed and its sound's very low. How should I fix it?

Dear sir,
My ipod once got formatted. Now I hear low sound from my ipod.

First, make sure your headphones are working properly. You can try them with another device, or try a different set with your shuffle.
If the headphones are fine, go to the shuffle's Settings or Summary screen in iTunes. It's the screen that appears when you select the shuffle in iTunes. There is a Limit maximum volume setting there. Make sure that slider bar did not get set to a low volume.
If that does not help, you can try doing a Restore on the shuffle in iTunes. The Restore button is on the Settings or Summary screen in iTunes. This will erase the shuffle, re-install its software, and set it to default settings. If the cause is related to a problem with software or settings, the Restore should fix it.
If that does not help either, there may be a hardware-related problem on your shuffle.

Sound quality: If you want to hear the difference between higher and lower bit rates

Have you ever wondered about the difference in the sound quality of music at different bit-rates? Can you hear the difference?
If you listen to 64kbps and 28kbps (either wma or mp3), you'll hear the great difference. However, if you listen to 28kbps and 92kbps (either wma or mp3), you'll find that there is little or no difference (to me, that is).
collegeboy wrote:
We all know that wma 28kbps sounds just as good as wma 320kb
ps.
the reason i and you go higher than 28 is because where able to. you can deny all you want.
If you want to experience better sound quality at higher bit-rates, the best thing to do is to listen to the music at a quiet place. This may sound like lame advise, but it really works. Try 320kbps for the best results. You'll be able to hear minor details you never had before.

SSR wrote:
Wayyyyyy back when I first started encoding MP3s I was using 28 with an inferior encoder. At the time I couldn't spot the difference, but now the difference is stark. Particular types of music (and more specifically instruments and combinations) do emphasise it though.
Actually, you cannot hear the difference when the background noise is loud, or example, public transport. I suggest that one uses a noise cancellation headset. $$$

Poor sound quality in timeline and export; fine in Source?

Hello all.
Newbie to Pr but experienced pro in digital audio. I'm stumped and know I'm just missing something somewhere.
I've made a music video for one of my songs. The graphics are all done (in AE), imported to Pr and eveything looks great. I import the final mix of the audio and it sounds very low quality when played from the timeline and in the final output, regardless of format (I've tried several presets and custom settings as well). I played around and noticed that the audio sounds fine when played from the Source window inside Premier.
The Pr session is comrised of 18 video tracks (not all playing at once, of course) and one stereo audio track.
I've tried re-exporting the audio from Logic at different bit depths, sample rates and file formats (mp3, wav, AAC, etc) but the results are the same every time: Source (Pr)sounds fine, Logic output sounds fine, rendered / timeline playback sounds like very low quality mp3 and final product sounds just as bad.
I've tried everything I can think of. I hope one of you can show me what I'm missing.
TIA!
Mark
Premier Pro CC
Processor 2 x 2.8 GHz Quad-Core Intel Xeon
Memory 8 GB 800 MHz DDR2 FB-DIMM
Graphics ATI Radeon HD 2600 XT 256 MB
Software OS X 10.9.1 (13B42)

Thank you for the reply!
I was experiencing the same results no matter what export settings I used. Plus the poor sound quality was present in the timeline itself, without even exporting the project.
I finally threw my hands up, started a completely new project, drug the same audio file in... sounded fine. Copied / Pasted the video clips from the original, broken project and boom, eveything is fixed. Yeah, corrupted Pr file it turns out. All I had to do was start a new project and import all the old components.
I've had to do this in Logic a lot (increasingly, these days). I just wish I'd tried it 10 hours earlier! Ha.
Anyway, problem solved, and thanks very much!

Why is the sound quality and volume in itunes so different than when I use other media players

This is an issue which has been vexing me for some time. I've researched it all over the web and have not found a worthwhile answer. Some other posts on these forums have asked similar questions without successful answers. But, none the less, I will try...
I have spent a lot of time over the last two years trying to get my itunes library organized as well as getting good digitized versions from my vinyl records as well as CDs. I was pleased with my results and then I added the songs to itunes. I could not believe how inconsistent the sound quality was. Invariably the volume is always lower. [Please do not post a reply such as: Check the volume controls in itunes proper as well as in itunes preferences (i.e., Sound Check, Sound Enhancer) & the Volume Adjustment in the Information pane under Options for particular songs.] I tried all of those means of adjusting volume. They do NOT work.
There is something more insidious at work in itunes which prevent good sound reproduction. I will give an example. I have played Frankie Valle and the Four Season's song "C'Mon Marianne" on the OS X system sound (i.e. clicking the play button to the song file when selected on the desktop or wherever it resides) as well as in Amadeus Pro. The song sounds great. When I play it when it's in the itunes' library the first part of the song is too lound and then when Frankie Valle starts singing his voice is at a significantly reduced volume.
I have edited the foregoing song in Amadeus Pro to a very high volume (i.e., Effects>Amplify), reloaded it into itunes and it still does not inprove the volume of Frankie's voice in the song, even though the rest of the song is somewhat louder. I have played with the Equalizer in itunes to no effect. It just does not work.
Now, I would glading move away from itunes and use another media player. However, I have other Apple devices through which I listen to music. And the only way I know of to listen,e.g., on the iphone is through itunes.
The other related problem with itune, or should I say iCloud, is icloud match. The icloud Match has taken great sounding music and given me back music of an inferior quality, even though it is a Matched AAC format.
I'm am sorry if I am a little peeved about this issue. If anyone has some suggestions or input to a solution, I will be eternally grateful. Thanks a bunch.

fbuerg,
You are welcome. Glad my good fortune was helpful to you.
Time Keeper

Extremely poor sound quality

Sound quality on two systems has recently become terrible. It sounds like underwater or too much vibrato/reverb. Could this be related to the latest QuickTime update?
G5, G4 Mac OS X (10.4.6) iTunes 6.0.4

Always a good start in this situation is to turn off the EQ using the appropriate tool in the lower right corner of the iTunes player window, and going to iTunes > Preferences > Playback and disabling Sound Enhancer.

MacBook Pro 13" Audio Output sound quality terrible after Lion upgrade

Hi guys,
I have recently upgraded my 2011 MBP 13 to Lion, and ever since have had terrible audio out sound quality, i.e. it is 'grainy' and full of feedback - very unpleasant to listen to.
Is anyone else in the same boat and does anyone have the solution to my problem?
Thanks,
Sam

Sorry for the late reply, yes mine does does recover but I still think it is the same issue with different levels of severity. This is a guess but possibly my higher spec Retina MacBook Pro can work its way through the issue where your 13" MBP can't or can't in a reasonable amount of time.
I have also thought that it is related to window server and was wondering if someone else would bring it up as semi-confirmation since 2 people would have to came to the same conclusion, yes I am weird you don't have to tell me. I am thinking it is possibly related to the lower priority for background apps; it gets caught thinking every window is in the background, chokes, and does not know what to do which is why the cursor will still move since it never gets "backgrounded". As for the caps lock, it is pretty much hardware based which is why we can have a virtual machine not read the caps lock on someimes if it is turned on when the VM is started.
I wish Apple would have more testers so things like this would not slip through. I see more complaints like this when there are external displays on MacBooks than single display iMacs/Minis. Something that may not be tested enough since it requires more specific circumstances.
Sorry, I don't know how to restart window server without the terminal. I would have loved to test the theory since that would answer the question of what is at fault quickly.

H55M-E23 low sound quality

Similar Messages

Maybe you are looking for