H67MA-E45 Updated to latest BIOS now won't load BIOS?

Hi,
I ran the latest BIOS update 7678v32, all seemed to go fine and it said BIOS update completed will now restart. Now the LED and fan starts for 1-2 secs then goes off straight away, this repeats every 10secs or so.
I've tried clearing CMOS but still nothing. Any ideas
Cheers
Andy

ok it sounds like a bricked board to me. you could try to first do a full CMOS clear to make sure!
how to perform a full CMOS Clear:
1: remove power cord from PSU!
2: hold power Button on case for 30 seconds!
3: remove the CMOS Battery for 5-30mins!
4: now use the Clear Cmos Jumper to clear Data and then put it back in Keep Position
5: put the CMOS Battery Back in!
6: Reconnect Power
7: Power the PC Back on
if that doesn,t get the board working you have bricked the BIOS chip and it needs to be Re-programed and that will leave you with 2 options:
1: send the board in to MSI for them to Directly Flash the Chip to get it working!
2: Take the Board to a shop that has a SPI Flash Programmer to directly Flash the BIOS chip!

Similar Messages

I just updated to the latest aperture, i have projects previously saved on a drive (in the old version) that now won't load... how do i update them?

Hi,
i just updated to the latest aperture, i have projects previously saved on a drive (in the old version) that now won't load... how do i update them?

But, unless I missed something, you are doing the repair with Aperture 3.5 so if 3.5 can't open an earlier library before doing the upgrade then unless I'm missing something the library will be upgraded before the repair is run, no?
OT:
You got me there, Frank - I wondered about the same thing, but Aperture is behaving differently, when upgrading a library, depending on if you are launching into the First Aid Tools or not.
I repeated my experiments, to explore this difference:
I restored an Aperture 3.4.3 library and launched the First Aid Tools:
Apertur went directly into First Aid Mode without first asking to upgrade.
Then "Repair" asked to be allowed to upgrade the library as you predicted.
During the upgrade "Aperture"showed "Rebuilding", not "Repairing" or "upgrading".
Second experiment: When I only double-click the 3.4.3 library instead of repairing, the upgrade alert is very different:
It takes a shorter time and does not show "rebuilding".
I am quite certain, that Aperture will use a different upgrade prodecure, when launched into the First Aid panel for repairing or rebuilding.

I'm now showing I have 9 updates in the App Store but when I click on updates it is blank and won't load. Tried to reset but didn't help. What now?

I'm now showing I have 9 updates in the App Store but when I click on updates it is blank and won't load. Tried to reset but didn't help. What now?

Try again later today or tomorrow. Other users are posting the same issue > Apps update not working. Was before but...: Apple Support Communities
The problem has been reported to Apple.

Firefox updated to latest version, now I can not enter data in a discussion board dialog box in Blackboard. IE8 had same problem, change to compatability mode and IE functions. Any fix for firefox?

Am using Blackboard to teach classes at college. Have not updated firefox at college, works great. Wife hit yes to update to latest version last week. Now can nan not reply in the discussion board, the curser is not recognized in the dialog box.

Try to disable hardware acceleration in Firefox.
*Firefox > Preferences > Advanced > General > Browsing: "Use hardware acceleration when available"
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

After updating to latest version, Firefox won't open

I am running Windows 7. After updating to the latest version, Firefox won't open. I get a notice when I try to open Firefox saying "Couldn't load XPCOM. Is there a way I can undo the update so I can get Firefox to open. It's my favorite browser...I'm having to use another browser to ask my question.

Do a clean reinstall and delete the Firefox program folder before (re)installing a fresh copy of the current Firefox release.
Download a fresh Firefox copy and save the file to the desktop.
*Firefox 23: http://www.mozilla.org/en-US/firefox/all.html
Uninstall your current Firefox version, if possible, to cleanup the Windows registry and settings in security software.
*Do NOT remove personal data when you uninstall your current Firefox version, because all profile folders will be removed and you lose personal data like bookmarks and passwords from profiles of other Firefox versions.
Remove the Firefox program folder before installing that newly downloaded copy of the Firefox installer.
*(32 bit Windows) "C:\Program Files\Mozilla Firefox\"
*(64 bit Windows) "C:\Program Files (x86)\Mozilla Firefox\"
*It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
*http://kb.mozillazine.org/Uninstalling_Firefox
Your bookmarks and other personal data are stored in the Firefox profile folder and won't be affected by an uninstall and (re)install, but make sure that "remove personal data" is NOT selected when you uninstall Firefox.
*http://kb.mozillazine.org/Profile_folder_-_Firefox
*http://kb.mozillazine.org/Profile_backup
*http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

AI file that has loaded many times previously into FC, now won't load

I am starting to lose my mind working with Flash Catalyst.   I have created a file within AI CS5, imported into FC CS5 numerous times, now all of a sudden it won't load. The error message "Error initializing import libraries" appears.   I had this issue happen before, but after much frustration, I went back and re-created the AI file under the Flash Catalyst New Document profile and that seemed to solve the problem, now, even with an AI file created with the FC document profile, a document that has loaded into FC MANY times successfully, all of a sudden won't load.   Of course I am at the end of the project and was ready to export the final SWF files and it does this. I am about ready to throw my computer out the window at this point.
It is not a large file, under 1MB in fact, so that is not the issue.   Is there some kind of FC cache somewhere on my computer that I need to clear out?   I have scoured the internet looking for a solution as I have a deadline of Wednesday of this week for this project and I can't find anything helpful. This is beyong frustrating and seems to make no sense as the AI file has imported successfully in it's current state many times.
I tried to rebuild the project, move its file location, rename it, cut and paste it into FC and nothing seems to work. In fact, I can't cut and paste a simple object at this point without getting the "Error initializing import libraries" error message.   PLEASE HELP ME ADOBE!   I AM DYING HERE!!!   Thanks!!!!!!!!!!!

I found the FC log files and the log for my last attempt at importing my AI file is below. Do I have a Java issue?   This is WAY above my pay grade, but I'm hoping maybe it's a simple fix? Run Java update?
!SESSION 2011-11-08 09:01:17.129 -----------------------------------------------
eclipse.buildId=unknown
java.version=1.6.0_16
java.vendor=Sun Microsystems Inc.
BootLoader constants: OS=win32, ARCH=x86, WS=win32, NL=en_US
Command-line arguments: -os win32 -ws win32 -arch x86 -clean
!ENTRY com.adobe.thermo.core 1 0 2011-11-08 09:01:28.111
!MESSAGE Loading ThermoPanels from bundleentry://51/ThermoPanelsSWF/ThermoPanels.swf
!ENTRY org.eclipse.equinox.p2.ui.sdk 2 0 2011-11-08 09:01:34.225
!MESSAGE Could not locate the running profile instance
!ENTRY com.adobe.flexbuilder.project 4 43 2011-11-08 09:02:09.931
!MESSAGE Error during import: Error initializing import libraries
!STACK 0
java.lang.Exception
    at com.adobe.flexbuilder.project.internal.FlexProjectCore.createErrorStatus(FlexProjectCore. java:972)
    at com.adobe.flexbuilder.util.logging.GlobalLogImpl.log(GlobalLogImpl.java:66)
    at com.adobe.flexbuilder.util.logging.GlobalLog.log(GlobalLog.java:50)
    at com.adobe.thermo.importnativeartwork.importer.ImportManager.showErrorDialog(ImportManager .java:1982)
    at com.adobe.thermo.importnativeartwork.importer.ImportManager.importArtworkIntoNewFile(Impo rtManager.java:404)
    at com.adobe.thermo.importnativeartwork.importer.ImportManager.importArtworkWithProgress(Imp ortManager.java:305)
    at com.adobe.thermo.welcome.ProjectCommands.importArtworkWithProgress(ProjectCommands.java:4 19)
    at com.adobe.thermo.welcome.ProjectCommands.access$0(ProjectCommands.java:405)
    at com.adobe.thermo.welcome.ProjectCommands$1.run(ProjectCommands.java:368)
    at com.adobe.thermo.interfaces.FlexDialogManagerInterface$RunnableWrapper.run(FlexDialogMana gerInterface.java:77)
    at org.eclipse.swt.widgets.RunnableLock.run(RunnableLock.java:35)
    at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:133)
    at org.eclipse.swt.widgets.Display.runAsyncMessages(Display.java:3800)
    at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3425)
    at com.adobe.thermo.interfaces.FlexDialogManagerInterface.doRunnable(FlexDialogManagerInterf ace.java:182)
    at com.adobe.thermo.importnativeartwork.ui.ImportProgressDialog.runImportNewProject(ImportPr ogressDialog.java:353)
    at com.adobe.thermo.welcome.ProjectCommands.doImportArtwork(ProjectCommands.java:361)
    at com.adobe.thermo.welcome.ProjectCommands.doImportArtwork(ProjectCommands.java:320)
    at com.adobe.thermo.welcome.ProjectCommands.createProjectFromArtwork(ProjectCommands.java:30 2)
    at com.adobe.thermo.welcome.ProjectCommands.createProjectFromArtworkRemote(ProjectCommands.j ava:313)
    at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
    at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source)
    at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source)
    at java.lang.reflect.Method.invoke(Unknown Source)
    at com.adobe.thermo.core.remoteobject.IncomingCommandHandler.invoke(IncomingCommandHandler.j ava:152)
    at com.adobe.thermo.core.remoteobject.IncomingCommandHandler.access$0(IncomingCommandHandler .java:139)
    at com.adobe.thermo.core.remoteobject.IncomingCommandHandler$1.run(IncomingCommandHandler.ja va:124)
    at org.eclipse.swt.widgets.RunnableLock.run(RunnableLock.java:35)
    at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:133)
    at org.eclipse.swt.widgets.Display.runAsyncMessages(Display.java:3800)
    at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3425)
    at org.eclipse.ui.internal.Workbench.runEventLoop(Workbench.java:2382)
    at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2346)
    at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2198)
    at org.eclipse.ui.internal.Workbench$5.run(Workbench.java:493)
    at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:288)
    at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:488)
    at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149)
    at com.adobe.thermo.application.ThermoApplication.start(ThermoApplication.java:133)
    at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:193)
    at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLau ncher.java:110)
    at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.jav a:79)
    at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:382)
    at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179)
    at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
    at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source)
    at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source)
    at java.lang.reflect.Method.invoke(Unknown Source)
    at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:549)
    at org.eclipse.equinox.launcher.Main.basicRun(Main.java:504)
    at org.eclipse.equinox.launcher.Main.run(Main.java:1236)

Since updating to iOS 6, gamecenter won't load?

So yeah, finally broke down and updated my iPhone 4 to iOS 6, and now Gamecenter won't load. Brown bars, green felt, aaand... CRASH. Every time. Any ideas?
Thanks!

I'll answer my own question because someone else might benefit and there is NOTHING on the web...
Get another device, log out of Gc, log back in, aaand... Presto.
DBC

Flashed BIOS, now there's a BIOS password? Why would Toshiba do this?

Failed BIOS update bricked my customer's Toshiba P205-S3647. Upon reflashing from USB floppy at boot, I am now presented with a BIOS password that was not previously there. I've searched high and low but cannot find the Toshiba default password. I flashed to an earlier BIOS ROM but same problem. Why would Toshiba do this? Please help!

There is no default BIOS password, and Toshiba didn't do that. That sounds like an error of some sort. Unfortunately, you'll need to have it serviced.
- Peter

I just upgraded to Safari 5.0.6 and my gmail now won't load. Please help.

I just upgraded my Safari to 5.0.6 (using Mac OS X 10.5.8) on my MacBook Pro and now my G mail account won't load...all I get is a blank page. G mail still loads with Firefox (which, for some reason, I do not have "permission" on my laptop to upgrade). I have deleted the cookies, cleared the cache, but still can't get G mail to work. Does anyone have a solution? Thanks so much.

Can you easily do this with Mac mail?
Yes you can.
Open Mac Mail. From the menu bar click Mail / Preferences then select the General tab.
Then select Accounts from the menu then the Account Information tab.
Click + (plus) under the Accounts window on the left.
Enter your name, your Gamil user name and password then click Create.
To start a new mail window, from the menu bar click File / New Message
Click the pop up menu next to: From
Select your Gmail account.
Click Attach form the new mail message window to include photos or links or just drag items to the window from your Desktop.

WinXP booted after BIOS update cleared RAID setting, now won't boot in RAID mode

I updated the P965 Platinum BIOS to 1.7 and my system stopped booting. After much experimentation I discovered it would boot if I unplugged the monitor and mouse, so I was able to "upgrade" to 1.6, and it's working again. However, the first time it booted blind with 1.7 it got all the way to Windows before I realized what happened.
My system was set up with a RAID1 pair, but the BIOS upgrade cleared the SATA mode to IDE, and it booted Windows before I changed it back. Now Windows won't boot when I set it to RAID. It complains <windows>/system32/hal.dll is missing or corrupt. It seems to work (mostly) when I put it back to IDE mode. How do I get it back to RAID1?
P965 Platinum
Core Duo 6600
2GB RAM
2x320GB Seagate SATA hard drives
Samsung IDE DVD-RAM drive

Quote from: erikFC on 05-November-07, 23:41:04
I updated the P965 Platinum BIOS to 1.7 and my system stopped booting. After much experimentation I discovered it would boot if I unplugged the monitor and mouse, so I was able to "upgrade" to 1.6, and it's working again. However, the first time it booted blind with 1.7 it got all the way to Windows before I realized what happened.
My system was set up with a RAID1 pair, but the BIOS upgrade cleared the SATA mode to IDE, and it booted Windows before I changed it back. Now Windows won't boot when I set it to RAID. It complains <windows>/system32/hal.dll is missing or corrupt. It seems to work (mostly) when I put it back to IDE mode. How do I get it back to RAID1?
P965 Platinum
Core Duo 6600
2GB RAM
2x320GB Seagate SATA hard drives
Samsung IDE DVD-RAM drive
Hi,
Why did you upgrade to 1.7 bios?
Also, you do not by have by any chance a Nvidia based card in system?
Del

890FXA-GD70 bios update via Live Updat & now won't load windows...help pls

Hi There
First off, please excuse the fact that I am not very experienced with the tech aspects of a home build (which this is & I bought off the builder), or any build for that matter..
I was getting a 'keyboard/interface' press f1 to continue error message, when I started my computer, along with most of the usb ports not working when windows 7 ultimate (64) sp1 (build 7601) loads.
Otherwise it was working fine..
So I deceided to follow the instructions of the Live Update tool & used the total installer to update the bios from American Megatrends V1.10 06/30/2011 to the latest bios. I know now that wasn't very wise (why is it even an option if it can do soooo much harm?).
After it updated the bios there was a question (which I don't recall of course), something about ROM I think and not being the same, with 3 choices to correct it and I'm pretty sure I went with the 1st option for it to be corrected.
So now when I turn the computer on it starts loading everything (I can get in to the bios setup), right after it shows the windows logo it flashes a blue screen with some type on it & goes to windows startup repair which of course doesn't help & tries to do a system recovery which also doesn't work.
I don't want to do any more damage by fiddling around with things I know little about.
I was encouraged to read in one of the post answers that if it gets to the point where Windows goes to load than the mobo is ok...hopefully!
Any assistance would be greatly appreciated.
Specs: (Copied from a Belarc Advisor scan)
O/S Windows 7 Ultimate (x64) Service Pack 1 (build 7601)
Main Board: 890FXA-GD70, Bus Clock: 200 megahertz BIOS: American Megatrends V1.10 06/30/2011
Processor: 3.30 gigahertz AMD Phenom II X 6 1100T Multi Core Not hyper-threaded
Drive: ST3500418AS Hard drive 500 gig SMART Status: Healthy
HL-DT-ST DVDRAM GH24LS50 ATA Device (optical drive)
Optiarc DVD RW AD-728OS ATA Device (optical drive)
PSU: Corsair GS500
12 gigs of RAM 1. 2048, 2. 2048, 3. 4096 4. 4096
Display adapter: MSI R7850 Twin Frozr 2GD5
Local Drive Volumes: c: (NTFS on drive 0)
Hopefully that is the required info on the specs.
Thanks in advance for any assistance.
Rob

yes the BIOS controls the CMOS from that User interface with all the settings menus!
and yes its in there where you can see what Drive mode its set at!
if its using the older style BIOS like my board has and not a UEFI then in this heading set:
1: go into your BIOS (press Delete)
2: Integrated Perifirals
3: On-Chip ATA Devices
4: Raid Mode <--- the options for that should be in there if its the same and may have been set to IDE mode before the update but may be set to AHCI now after you flashed the BIOS via live update which is more then likely why your getting a BSOD as it in the wrong operating mode!

I just updated to latest version, now sidebar (bookmarks, downloads) won't widen beyond a certain width, though the main window will. What should I do?

The left right arrow toggle button works only so far going to the right, then the sidebar separates and doesn't expand any further. Any ideas how to get the toggle button to stay connected to both sidebar and main window??

'''Try Firefox Safe Mode''' to see if the problem goes away. Safe Mode is a troubleshooting mode, which disables most add-ons.
''(If you're not using it, switch to the Default theme.)''
* Open the Help menu and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
''Once you get the pop-up, just select "'Start in Safe Mode"''
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension.
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
Please report back with your report.

Security update interrupted... now WON'T BOOT?

I just did the most recent software update, installing the new security update thing, but my MacBook froze in the middle, and now it won't start up.
All I see is a a screen with an apple and a little spinner, like I normally do at startup, but it doesn't go away. I've left it for 10 minutes, and nothing.
The trick is, I can't find my restore disks. Is there any way to resolve this without them? Maybe put the thing in firewire HD mode, and put replace the system files from another computer?
HELP!!!!

You need to find the install package that shipped with your Mac for a number of important reasons - the ability to run Disk First Aid repair and in case you ever need or want to perform an Archive & Install or an Erase & Install or re-install an individual application, etc. In addition if you ever sell your Mac at some point, the person that makes the purchase will want and expect the install package that shipped with your Mac when new which is model and build specific.
I strongly suggest that you contact AppleCare with your computer serial number available to request a replacement install package for your Mac. I believe all you will be required to pay is a shipping and handling fee and keep the replacement in a known/easy accessible/safe location.
You can run fsck via a command line which is not as good as running Disk First Aid repair via Disk Utility when booted from your Tiger install disc but better than nothing. You can't replace any system files from another Mac - how would you know what to replace and you would need to do so from an identical model and build anyway which is why you need to request a replacement install package.
http://docs.info.apple.com/article.html?artnum=106214

TS4148 Have just updated to 6.0, now won't recognize SIM, what next?

Have just updated to iOS 6. When update completed the No SIM icon activated. Have tried to restore settings, but no help. now at a point that when I try to power up it won't activate due to not recognizing the SIM. SIM has been checked.

IPod does not appear in iTunes
http://docs.info.apple.com/article.html?artnum=61771

I am receiving an error message when updating itunes - now won't load?

Somehow my Itunes update was interrupted a few days ago and now I am receiving an error message "Error 7 Windows 126" and MSVCR80.dll was not found and need reinstallation. Thanks

Try the following user tip:
Troubleshooting issues with iTunes for Windows updates
Fo the reinstall, use a fresh copy of the iTunesSetup.exe (or iTunes64Setup.exe) installer file downloaded from the Apple website. (Delete any versions of the installer file that you currently have in your downloads areas.)

H67MA-E45 Updated to latest BIOS now won't load BIOS?

Similar Messages

Maybe you are looking for