H9-1150 PC wont Boot with WIndows 7 Premium 64 bit with ASUS 960 GTX Card.

I saw others have posted simular issues but i thought id repost this again in case there is more help.  I have the Pavalion Elite Phonix h9-1150 desktop with Windows 7 Home premium 64 bit.  and the HP 7.07 bios (seems no way to upgrade  the bios).
The issue is like others have had i install the new graphics card the Asus 960 GTX Card which came out last month and the system starts up  gives about 3 beeps in about 30 seconds each and then it goes to a black screen with a blinking curser and nothing else happens. cant enter bios or  the HP settings..
I did try to disable UEFI boot devices in the bios settings and only enable legacy devices (after switching back to my original card then switching to the new card) but it still gives the 3 beeps upon booting.   However i was able to enter windows. though i think it may be due to shutting off the computer with the old card in without powering down first. and  after the 3 beeps happens (which still locks you out of the bios menu) it shows up the window where you can select safe mode or normal mode.. as sometimes happens if you boot up your computer with windows 7 if you had just turned it off without powering down or something.  Through that i am able to enter windows and run the PC and graphics card with no issue its just when i try to boot the issue happens.
and No HP suppor it is NOT a defect with the Card itself. Like many before. i bought a EVGA Card a while back a 780 GTX and the SAME issue happend (though i didnt try the removing the UEFI boot devices then) ...
There is a spacific issue with HP computers that seem to lock out "new" hardware from booting.
Honestly ill be blunt. I really think this is poor doings I read somewhere that while HP will never state it they do this on purpose to prevent people messing up warrenty or any "liabity" occuring by people installing other hardware onto HP stock computers
that makes no since to me.  the PC SHOULD be able to run the card. in fact its running it now once i was able to bypass the lock out (temporarly)  check benchmarks everyhting is fine the card runs 3 times faster  then the old one (as should be the case).
But its just this lockout that HP for some reason has installed on their bios/motherboards that is the issue.
Good news is i got it from amazon and i have about a month till i have to return it. which i think this time i will do.  to see if anything crops up in a month or something.
The ONLY solution it seems HP offically has is that to disable secure boot under windows 8
but this is not a windows 8 computer. and i do assume even if iINSTALL windows 8 . the issue would not go away because since its an older bios there would be no way to have a secure boot option to remove?
HP you really need to get on the ball and give us a direct reply on this.  Is there ANY WAY to fix this? Can you not simply  make a update of older bioses to allow this? Or do you just not want to worry about older pCs?
either way i think this is wrong and very frustrating and to be honest. If this is the case when my pc otherwise SHOULD run the card
its a PCI express 16x slot that is 3.0
here is the deetailed specs as per your page
http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c03273835
the card SHOULD WORK fine.  I thought the 780 GTX was a bit too much for the PC as it had more then a six pin port and needed a bit more power so at first i thought that was the issue. so i returned it. and got this new card now.
however the ASUS 960 GTX card requires the SAME power supply as the default GTX 550 Ti card and the SAME SIX PIN connector
so it SHOULD work.
and benchmarks show that it DOES its just the stupid bios ..that is having the issue.
i am afraid to power down the computer at the moment and try again to see if windows boots normally after disabling the UEPI boot devvices because it may not boot  properly.......
HP you are one of the biggest suppliers of computers you know technology these are YOUR computers.  WHY cant you give us a direct awnser over this.
ITS VERY frustrating
and to be honest if i cannot resolve this issue i am very hestient to ever buy another HP product if their computers spacifically have this new hardware lockout mode.
because i have the card running now on my pc it runs great! 3 times faster as it should! and yet i know in the back of my mind if i cant figure out this issue likely ill just have to send it back.........least i have some time.
and right now i dont have the money to buy a new pc . this PC is JUST fine for what i need for now other then wanting a bit better card...
it shoudnt be this much of a hassle should it?
Thank you.
This question was solved.
View Solution.

Hi,
You need the BIOS update that is listed under Windows 8 in order to support the newer graphics.   You need to upgrade to Windows 8 or temporarily install Windows 8 so that you can install the BIOS update.  While there may be other ways to install the BIOS update, clearly having Windows 8 running will be the safest way.  The version 8 BIOS is your best chance at getting the newer graphics cards to work.
You can trial Windows 8 Enterprise for 90 days.
If you decide to install W8, then create the HP external recovery media and backup your data before you do anything.
The reality is that there is no guarantee that any particular graphics card will work in any particular PC even if the graphics card works in other PCs or even the same or similar model PCs. Know what the return policy is before you buy.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Similar Messages

  • PC wont boot with X-Fi Fatal1ty card instal

    ok, so my pc refuses to boot when this card is installed. im running Windows Vista Ultimate x64 Bit
    on a ASUS Striker Extreme motherboard, with 2 gigs of 800Mhz Crucial ram, and i have a GeForce 8800GT installed and nothing else. when i get the loading screen of vista on startup. the loading bar startes to fade in, then i BSOD and pc restarts its self. tried booting in safe mode, it loads all the drivers stops when trying to load crcdisk.sys and then BSOD and restarts its self. i've tried everything in my bios. onboard audio isnt installed when i do this and its set to disabled in the bios. i even tried with it enabled and onboard audio card not installed. and with the card installed disabled and enabled. it just dosnt want to work. i have the latest bios. i even tried reflashing it. no clue whats going on. person told me its possible its my PSU but i have a 700W PSU. if any knows please help

    If possible, you might want to try the card on another computer. This should tell you if the card is faulty or if there's something else that needs work on your current system.
    If you are unable to test the card on another computer or if the card does work on another system, you might want to contact support and providing the system information so that they can assist you. Be sure to run the system information utility only after you have installed the sound card on the system in question.
    The article below further explains on the Creative System Information Tool.
    http://us.creative.com/support/kb/ar...p?l=3&sid=2964

  • Edge 531 puter wont boot in Windows 8.1 "auto repair going for over 2 hours"

    PuteR wont boot up windows cant do restore repair anything but watch "repairing disk errors this might take ovewr one hour to complete" that was 2 1/2 hours ago Have a windows 8.1 repair dvd disk and something on a flash drive I made a year ago but cant get puter to boot from them . Cant get windows to bootup. Cant figure out how to procede  Really cvould use some advice/help ps puter was running fine just hours earlieR  AM STUMPED lol Thanks

    ashtastic wrote:
    Now using a linux live usb drive, boot into your favorite brand of linux and run gparted.  You should see your unallocated space sandwiched between your OS X partition (which gparted may or may not formally 'see') and the NTFS Windows partition.  Simply move the Windows partition over to occupy the unallocated space and extend it to the end of drive and you're done. 
    Everything has worked so far, I have freed up about 75GB that is in between OSX and my 8.1 Bootcamp Partition, however I can't for the life of me seem to make a working Linux USB. How can you make a BOOTABLE (from this retina macbook pro) Live CD with Gparted. What tools/ISO did you use?

  • Wont boot after windows update

    M y Sateite A305 s6916 wont boot after windows updates tried to install.

    Satellite A305-S6916
    tried .. every option on F8
    Try this. Download a repair disc from here.
       Windows Vista Recovery Environment ISO X64 version (64 bit)
    If you can reach the Recovery Environment by booting that, try the Startup Repair and let us know what happens. Sometimes you need to run it more than once.
       Startup Repair: frequently asked questions
    Also try a System Restore.
       What are the system recovery options in Windows Vista?
    -Jerry

  • I can t update my ipod touch 4th gene. because I had a version of i tunes on my computer for windows 7 premium 6e bits that didn t work well. So I uninstalled it and try to install e newer version but the newer version won t read the music from the older

    I can t update my ipod 4th gen. for facebook because I uninsatalled the program itunes from my computer  as it didn t work well it would freeze on me all the time. So i installed another version for windows 7 premium 64 bits, but when i tried to open it it wouldn t let me as it said it coudn t read the music library from the last version of i tunes . So I uninstalled it too. So Now I really don t know what to do ??????

    thanks I didn't end up needing to try it! my ipod randomly decided to work again like "hmm, Ellie seems to have been really annoyed at me for ages now, maybe I should try being nice to her or something like that"

  • Will my creative suite 3 program work on windows home premium 64 bit computer? I need to switch computers because my current pc is windows xp

    will my creative suite 3 program work on windows home premium 64 bit computer? I need to switch computers because my current pc is windows xp

    yes, though you may need to use compatibility mode to install.

  • P35 Neo FR wont boot with 1066 Ram

    Hi Guys,
    I have a problem with a new build.  The specs are
    P35 Neo FR
    E8400 (not overclocked)
    2 gb Crucial Balistax tracer 1066 Ram
    XFX 7900GS card
    450W PSU
    It will boot and I have been into windows to which all seems fine, however I have an issue.
    1. The BIOS and CPU-Z are showing my ram at 667.  I have manually adjusted it to 5-5-5-15 and set the divider so it should be running 1066.  However it wont boot and goes into the re-boot over and over and over and over and over again "mode".  This can only be rectified by re-setting the CMOS and then it will boot with its origional 4-4-4-24 timing @ 667.  I have checked the voltages and they make no difference.  It will only boot when the LED's on both ram sticks are lighting up on first power up.  Ram has been tested in another PC and doesnt seem an issue. 
    Bios is 1.5 I think.  Should I flash and go to 1.8?
    I will also try the Mobo, PSU, HD and GPU without anything else attatched to see if there is a problem
    Also, 1 stick of ram at a time to see if thats causing an issue.
    I would appreciate any suggestions 
    Thanks

    Quote from: Jack the Newbie on 19-March-08, 22:28:13
    Which FSB/Memory Ratio did you choose in BIOS?
    Does it work, if you choose the divider for DDR2-800 MHz?
    What is the memory voltage recommended for these modules @1066 MHz effective speed?
    Did you try with one stick of RAM only?
    Thanks for the quick reply
    I think the divider was 1.1-6?  I will confirm in a couple of hours once I am home. It works at 1-1 but the speed was 400mhz.  It also ran at 667. Whatever that divider was.
    I am going to try the one memory module test tonight and I will also report on that and the DDR800 settings.
    http://www.crucial.com/uk/store/partspecs.aspx?IMODULE=BL2KIT12864AL1065  Is my ram and its rated at 2.2V
    Thanks in advance and I will update in the next few hours.

  • Comp wont boot with ram in any slots besides 1&3 no matter what, faulty board?

    Ok i've tried pretty much everything, got latest bios, changed timings to everything but the comp just wont boot if I have any ram in slots 2&4. Actually got the comp to boot up with ram in slots 1&2 once, but tried with all 4 slots filled and didn't work, and after that slot 2 didn't work again.
    Could it be a faulty board? I know it's not the ram.

    Ahh, turns out you were right tiresmoke.
    Even though I thought I had 4 sticks that were exactly the same..one wasn't. 3 of them are xms32004.1 0427033 - 0...the one i've always had in my comp is 5.1 0430069 - 1. Put in 2 of the 4.1 and was able to run dual channel np. That explains why one time I was able to run dual channel then switch the ram and couldn't..had no idea there was minor differences..and have no idea why I got 3 of one kind and 1 of another when I orderd the 4 sticks.
    Going to try and exchange the 4 sticks for 2 1 gig sticks..how good is neweggs return policy heh? Been like nearly 2 months..

  • Comp wont boot with ram in any slots besides 1&3

    No idea why...have 4 of the exact same ram and i've mixed and matched so it's not the ram..if I put ram in slot 2 or 4 the comp just wont boot.
    Anyone know what is causing this? Thanks in advance
    Corsair xms 3200 and k8n neo2 plat btw

    Quote
    Originally posted by Paul Foster
    Mine works just fine. Take one step at a time. Go back to the minimum configuration and use memtest86 to try to isolate where the problem is. This thread is a great place to start:
    Basic Building tips
    ditto - usual problem is BIOS - stick in one stick - boot into windows or whichever way you normally flash your BIOS and get the latest bios

  • MSI p67a-gd53 (b3) Wont boot with ram in slot 1 and 3, or 2 and 4.

    Hi i recently built my own system, with just one ram stick in it boots fine and everything.
    When i try to put the other stick in slot for so that in runs dual channel it just wont boot, it turns on starts the fans up and then just goes off, and repeats this.
    The ram i have is Corsair Vengeance Low Profile 4GB (2x2GB) DDR3 PC3-12800C9 1600MHz Dual Channel Kit.
    It also doesnt work in slots 2 and 4, can anyone help me :(?
    My setup is :
    OCZ ZS Series 650W '80 Plus Bronze' Power Supply
    Intel Core i5-2500K 3.30GHz (Sandybridge) Socket LGA1155 Processor - Retail
    MSI P67A-GD53 Intel P67 (Socket 1155) DDR3 Motherboard
    MSI ATI Radeon HD 6870 OC HAWK 1024MB
    Corsair Vengeance Low Profile 4GB
    Seagate Barracuda 500gb HD
    Gets no beeps on boot with just one stick in, im really confused :s
    All Help will be appreciated.

    Both ram sticks worked in slot one and it would boot but I tried running a game and it froze each occasion, cud this be due to the ram being dual channel and only having one in? Or that the ram has the wrong settings.
    I have returned the motherboard along with the ram to the shop i got it from for tests to see if the dimm slots had problems. Il let you guys know what they say.
    Thanks for the advice, when I get it back il build it again and see if it runs fine, if not il try the things youve said.
    Can anyone else shed any light on this? Any other things I may have to try?
    Thx again

  • New Z87-G45 wont boot to windows - restart loop

    I purchased a new MSI Z87-G45 Mobo and i5 4440 and now I cant boot into windows.
    It was blue screening but now it just gets to windows load screen for a second and then restarts.
    I have an older sata HDD would that be the issue?
    I was able to install windows on a new SSD and it boots and works fine so its obviously something to do with the older HDD.

    you can't boot from older OS installation on new different mobo

  • HP 8740w WH279UA wont boot after Windows 7 Updates

    Hi!
       Thank you all for reading my case. I'm the happy owner of a HP 8740w, I have 20GB of RAM and 500GB hard drive. My litle monster has been working perfectly for the last year and a half.
    My problem began last night while I was doing a fresh Windows 7 Pro Installation, I did this after installing Windows 8.1 on the laptop and I was not happy with the overall system performace. these are the steps I run before the computer stopped working:
    1. Boot from Windows 7 Pro DVD
    2. Delete/Create/Format hard drive
    3. Computer Boot Ok
    4. Installed Wifi Driver Ok
    5. Downloaded all System Drivers from HP website
    6. Installed all System Drivers
    7. Reboot computer it showed 107 windows Updates to be applied
    8. Computer Rebooted 2 times while configuring updates
    9. Computer Failed to Boot
    Now every time I boot the computer the Caps Lock and Num Lock leds Blinks 3 times, according to HP Web Site the 3 times blinking leds indicates Memory Chip failure,  these are the steps i tried to troubleshoot the memory error:
    1. Boot the computer with the combination of the 4 memory so-dimms, failed
    2. Boot the computer without memory, failed
    3. Boot the computer without memory, and without hard drive, failed
    4. Boot the computer without memory, hard drive, and motherboard battery, failed.
    I reallt don't understand how can this had happend to my laptop. Warranty ranned out on 2013 so i'm not elegible to request a replacement. any ideas?

    Hi dgonzalezln,
    Your Elitebook 8740w is a commercial product and to get your issue more exposure I would suggest posting in the commercial forums. Here is a link to the Commercial Notebook forum.
    Thank you,
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • RADEON 7950 WONT BOOT WITH P67A-GD65

    Just got a new ATI Radeon HD7950 graphics card a couple of days ago and it refuses to even boot in my main PC (Intel i7-2700K, MSI P67A-GD65).
    Won't even get into BIOS. Just black screen.
    Updated to latest BIOS. Still nothing.
    Today I have tried the card in an older PC (Intel Q6600, ASUS Maximus Formula) and it works just fine.
    So I thought it might have been a power supply issue so I swapped the power supply from old PC into my new PC, but it still didn't work.
    So now I think its an incompatibility with the MSI P67A-GD65 motherboard.
    Note: Previous graphics card was ATI Radeon 6870 which is still working fine with P67A-GD65.
    Can anyone suggest why this graphics card won't boot with the P67A-GD65?

    Quote from: Froggy Gremlin on 02-March-13, 06:16:55
    What OS are you running? UEFI/BIOS version? CPU? Is this an MSI graphics card? If not, have you visited with the card manufacturer for any available information they may have?
    Too much time passed for me to edit and delete this question of CPU, as you did list it.

  • Visual studio wont install on Windows 8.1 32 bit machine

    The install goes through the motions then fails to install.
    n.Wright

    Double post of thread
    https://social.msdn.microsoft.com/Forums/en-US/9b84ad66-7d29-4aad-9e18-e312276b8105/visual-studio-wont-install-on-windows-81-32-bit-machine?forum=visualstudiogeneral in which the OP advised Windows 8.1 was not up to date and apparently updating Windows
    8.1 resolved the issue.
    La vida loca

  • CS3 Production Premium compatibility with Windows 7 Premium 64 bit?

    I am starting to think that CS is not compatible with Windows 7 Home Premium 64 bit.
    Can anyone confirm this?
    If so, is there a way around it?

    I recommend you expand your search to include the Photoshop forum. Some people there have bene running W7 ever since the first Public Beta was released and they may know which buttons to push. It generally seems to work, though, so your issues are probably caused by a specific combination of hardware, drivers and system libraries eitehr missing or not being installed correctly.
    Mylenium

Maybe you are looking for

  • I dropped my Iphone in water and the on/off button stopped working, how do I fix it?

    I dropped my phone in some water and it was only in there for about two or three seconds. I grabbed it and dried it straight away and made sure to get in all of it, and it was fine, everything worked. But about an hour after the on/off button stopped

  • Any Function Module which will give user id or position

    Hello Friends,    is there any standard function module which will give the attribute position id or user name if i pass the 'attribute id as CNT' with value of the CNT. i know there is a standard function module 'BBP_READ_ATTRIBUTES'. but this FM wi

  • Smooth movement of images

    Hi, I am just experimenting with a kind of JavaFX slide show component but I have a problem with smoothly letting images flow over the screen. Especially when the images are moving slowly you can see them jump from one pixel position to the next. Jav

  • Firefox closes at start

    Firefox closes on first attempt to start after boot. Seems to work fine after. Windows 8.1 Comcast customer with Constant Guard Protection Suite and Norton Security Suite but all disabled Problem occurs after start or restart Persistent in safe mode

  • Bid invitations in SUS

    Hi experts I am configuring the integration bid invitation and SUS, so vendors already can acsses SUS and create responses for bids, when vendors click in BID INVITATION the system open a new page with the bid invitations, I need the system open the