HA SKU AP fallback is not working

According to the N+1 deployment guide, when the primary controller comes back up/online, the APs on the secundary (HA SKU) controllers should fallback to the primary. During my tests, this did not work. I enabled "AP Fallback" on both primary and secundary (HA SKU) controllers, but the APs remain on the secundary (while the primary was back online). Only after a boot of the secundary, did the APs go back to the primary. Is this normal ?
How long can it take for an AP to fallback ? I waited 10 minutes.
NOTE: the HA SKU is going to server multiple controllers, so he is not configured with the IP or name of any primary controller. I guess it is the AP itself that needs to remember what his primary controller was....
regards,
Geert

see below
- make sure AP SSO is disabled.
>> checked and true
- configure backup controller on the primary. WLC GUI>Wireless>Access points>Global Config
>> is done
- configure high availablity tab on the AP's
- made sure that the names of the WLC on the AP high availablity tab are identical "case sensitive"
>> ha, this is interesting. Are you saying that i need to configure this tab on each and every AP for AP fallback to work ??
>> I thought configuring the global redundancy Wireless -> Global Config would be enough (backup primary controller)
regards,
Geert

Similar Messages

  • Fallback Settings Not working for Non-Agreement Senders

    I am trying to test the fallback settings for X12 in Biztalk 2010.  I am processing an 837P and have one agreement in place that is processing files correctly when file is from the 'from' party of the agreement.  I am trying to use fallback to
    process files that are from a sender that is not part of the agreement.  I have enabled fallback and configured correctly as far as I can see.  When I send this type of file thru, I get these warning/errors in the event viewer - any thoughts?
    Error encountered during parsing. The X12 transaction set with id '' contained in functional group with id '125482', in interchange with id '000125482', with sender id '      382674344', receiver id '38-6004862    
    ' is being suspended with following errors:
    Error: 1 (Miscellaneous error)
     6: Finding the document specification by message type "http://schemas.microsoft.com/BizTalk/EDI/X12/2006#X12_00401_837" failed. Verify the schema deployed properly.
     A message received by adapter "FILE" on receive location "837_Receive_Location" with URI "c:\837\*.txt" is suspended.
     Error details: An output message of the component "Unknown " in receive pipeline "Microsoft.BizTalk.Edi.DefaultPipelines.EdiReceive, Microsoft.BizTalk.Edi.EdiPipelines, Version=3.0.1.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" is suspended due
    to the following error:
         Error encountered during parsing. The X12 transaction set with id '' contained in functional group with id '125482', in interchange with id '000125482', with sender id '      382674344', receiver id '38-6004862    
    ' is being suspended with following errors:
    Error: 1 (Miscellaneous error)
     6: Finding the document specification by message type "http://schemas.microsoft.com/BizTalk/EDI/X12/2006#X12_00401_837" failed. Verify the schema deployed properly.
     The sequence number of the suspended message is 1. 
     MessageId:  {D2CC89CA-5080-48E6-A9BF-7ABF6F37E9F2}
     InstanceID: {E2416749-D653-461B-9B7D-54AA47F75D00}
     Agreement Resolution for x12 Protocol based on the context properties DestinationPartySenderQualifier with value "ZZ", DestinationPartySenderIdentifier with value "38-6004862", DestinationPartyReceiverQualifier with value "ZZ" and DestinationPartyReceiverIdentifier
    with value "382674344" has failed.
     There was a failure executing the send pipeline: "Microsoft.BizTalk.Edi.DefaultPipelines.EdiSend, Microsoft.BizTalk.Edi.EdiPipelines, Version=3.0.1.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" Source: "EDI Assembler" Send Port: "837 Send 997"
    URI: "C:\837\ack\997_%SourceFileName%_%MessageID%.txt" Reason: Agreement Resolution based on the context properties for x12 Protocol has failed.
     Agreement Resolution for x12 Protocol based on the context properties DestinationPartySenderQualifier with value "ZZ", DestinationPartySenderIdentifier with value "38-6004862", DestinationPartyReceiverQualifier with value "ZZ" and DestinationPartyReceiverIdentifier
    with value "382674344" has failed.
     There was a failure executing the send pipeline: "Microsoft.BizTalk.Edi.DefaultPipelines.EdiSend, Microsoft.BizTalk.Edi.EdiPipelines, Version=3.0.1.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" Source: "EDI Assembler" Send Port: "837 Send TA1"
    URI: "c:\837\ack\TA1_%SourceFileName%_%MessageID%.txt" Reason: Agreement Resolution based on the context properties for x12 Protocol has failed.
     A message sent to adapter "FILE" on send port "837 Send 997" with URI "C:\837\ack\997_%SourceFileName%_%MessageID%.txt" is suspended.
     Error details: There was a failure executing the send pipeline: "Microsoft.BizTalk.Edi.DefaultPipelines.EdiSend, Microsoft.BizTalk.Edi.EdiPipelines, Version=3.0.1.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" Source: "EDI Assembler" Send Port:
    "837 Send 997" URI: "C:\837\ack\997_%SourceFileName%_%MessageID%.txt" Reason: Agreement Resolution based on the context properties for x12 Protocol has failed. 
     MessageId:  {D053BF43-B315-48C9-9024-842FE53B9906}
     InstanceID: {0732CFD5-A997-4704-9D29-B273E104486A}
     A message sent to adapter "FILE" on send port "837 Send TA1" with URI "c:\837\ack\TA1_%SourceFileName%_%MessageID%.txt" is suspended.
     Error details: There was a failure executing the send pipeline: "Microsoft.BizTalk.Edi.DefaultPipelines.EdiSend, Microsoft.BizTalk.Edi.EdiPipelines, Version=3.0.1.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" Source: "EDI Assembler" Send Port:
    "837 Send TA1" URI: "c:\837\ack\TA1_%SourceFileName%_%MessageID%.txt" Reason: Agreement Resolution based on the context properties for x12 Protocol has failed. 
     MessageId:  {A5BD0F9D-8AEC-4C33-A194-59EF0C619F87}
     InstanceID: {877126CD-1630-4FC9-9D30-F2EAA4AB09E7}
    Mike Dugan

    Hi Mike,
    For the error " Finding the document specification by message type "http://schemas.microsoft.com/BizTalk/EDI/X12/2006#X12_00401_837" failed."
    Can you check out the section for X12 Schema Discovery in the following link
    http://msdn.microsoft.com/en-us/library/bb246089(v=bts.70).aspx. As you are using 4010A1 837_P, your incoming document should have 004010X098A1 at GS08. Or if providing  004010X098A1 at GS08 is not a requirement for your other partners,
    then I would recommend you to deploy 837_P schema by removing `_P` extension at the root node, such that the schema that you have deployed would be "http://schemas.microsoft.com/BizTalk/EDI/X12/2006#X12_00401_837"
    and that is what EDI Receive pipeline would look for.
    Regarding the other error for the 997 and TA1 documents failing with "Agreement Resolution based on the context properties for x12 Protocol has failed.". It is a new constraint that we have imposed on the EDI users in BizTalk 2010 that the 997/TA1
    that gets generated in EDI Receive Pipeline for an incoming document should resolve to an agreement with Sender and Receiver Identities which are the reverse of the Sender and Receiver Identities (ISA 5 6 7 8) in the incoming document. EDI Receive Pipeline
    would promote the following context properties DestinationPartyReceiverIdentifier, DestinationPartyReceiverQualifier, DestinationPartySenderIdentifier, DestinationPartySenderQualifier and EDI Send Pipeline has to do Agreement resolution based on them. Hence,
    there has to be an agreement with those particular identities otherwise the acknowledgements would fail. For your scenario I dont see any other way for you other than writing a custom pipeline component to remove those context properties by nullifying the
    values of the above mentioned context properties for all the messages with MessageType is
    http://schemas.microsoft.com/Edi/X12#X12_TA1_Root or
    http://schemas.microsoft.com/Edi/X12#X12_997_Root such that the messages would resolve to fallback settings. For more details on Agreement Resolution in EDI Send Pipeline please go through
    the link
    http://msdn.microsoft.com/en-us/library/bb259945(v=BTS.70).aspx
    Thanks,
    Kowshik Palivela

  • OAM 11gR1: WNA Fallback does not works

    Hi all
    I have configured Kerberos authentication in OAM 11.1.1.5 BP04 and it works fine. The basic authentication also works fine in my environment.
    But when I try to access the OAM protected resource from a browser which is not configured for WNA, I get a basic prompt for credentials and upon providing valid/invalid credentials, I am redirected to an OAM error page with the following message:
    Error: The user account is locked or disabled. Please contact the System Administrator.
    I am not able to figure out what can the problem be. Any clue will be appreciated. Thanks !!!

    WOW, that solves the problem. Still not clear why selectBooleanCheckbox needed PPR, but the other inputText components that are part of the same record in the form do not need PPR.
    Thanks, a lot.

  • ISE 1.1.1 (Fallback to local Vlan if radius server is found to be dead) not working

    We have configured following commands on switch to fallback to local Vlan if both radius server (policy persona's) is found dead. For test purpose we shutdown both servers (policy persona's) but fallback didn't work. We have 3750 switch running image 12.2(55)SE6 having following configuration.
    We do not know whether we configured switch in proper way or do we need to modify it.
    aaa new-model
    aaa authentication dot1x default group radius
    aaa authorization network default group radius
    aaa authorization auth-proxy default group radius
    aaa accounting update periodic 5
    aaa accounting auth-proxy default start-stop group radius
    aaa accounting dot1x default start-stop group radius
    aaa accounting system default start-stop group radius
    aaa server radius dynamic-author
    client 10.10.10.10 server-key 7 12345678 (Policy Persona 1)
    client 10.10.10.11 server-key 7 12345678 (Policy Persona 2)
    server-key 7 12345678
    ip device tracking
    epm logging
    radius-server attribute 6 on-for-login-auth
    radius-server attribute 6 support-multiple
    radius-server attribute 8 include-in-access-req
    radius-server attribute 25 access-request include
    radius-server dead-criteria time 30 tries 3
    radius-server host 10.10.10.10 auth-port 1812 acct-port 1813 key 7 12345678 (Policy Persona 1)
    radius-server host 10.10.10.11 auth-port 1812 acct-port 1813 key 7 12345678 (Policy Persona 2)
    radius-server vsa send accounting
    radius-server vsa send authentication
    Port Configuration
    interface GigabitEthernet0/1
    switchport access vlan 305
    switchport mode access
    ip access-group ACL-DEFAULT in
    authentication event fail action next-method
    authentication event server dead action reinitialize vlan 305
    authentication event server alive action reinitialize
    authentication host-mode multi-auth
    authentication open
    authentication order mab dot1x
    authentication priority dot1x mab
    authentication port-control auto
    authentication periodic
    authentication timer reauthenticate server
    mab
    dot1x pae authenticator
    dot1x timeout tx-period 10
    spanning-tree portfast
    Please help....
    Thanks

    Tabish-
    The pre-auth ACL that you have on your port is used for what's called a "Low-Impact" mode type of setup. With Low-Impact mode you are allowing services defined in the pre-auth ACL until the user/devices is authenticated. Once authenticated the pre-auth ACL gets replaced with the dACL/authorization policy that you have defined in the authorization profile. As a result, it is not possible to use "fail-open" configuration with low-impact as there is nothing to replace that pre-auth ACL since your NAD device(s) are unavailable.
    If you want to use the "fail-open" features you will have to use the "High Securty/Closed Mode." In that mode you cannot utilize the pre-auth ACL and essentially only EPoL traffic is allowed on port until authenticated.
    For more info you should reference the TrustSec design guide located at:
    http://www.cisco.com/en/US/solutions/ns340/ns414/ns742/ns744/landing_DesignZone_TrustSec.html
    Thank you for rating!

  • ITunes 12.1.1 does NOT work with Windows - Fix??

    Hi everyone,
    I had issue after issue with the latest iTunes update (12.1.1) not working on my windows 7. It simply would not lunch when clicking on the shortcut to open.
    After a fair bit of searching I found this alternative version which seemed to do the trick and now it works:
    iTunes 12.1.1.4 for Windows (64-bit - for older video cards) - iTunes64Setup.exe(2015-02-18)

    The "for older video cards" installer - which, like most prior "64 bit" versions of iTunes, is actually a 32 bit application with a 64 bit installer - may be a useful fallback if the full 64 bit version does not install or run correctly.  Although 12.1.1.4 is a major improvement over 12.1.0.71, there are clearly still some lurking incompatibilities with some 64 bit Windows systems/components.  It is, however, a little misleading to say that "iTunes 12.1.1 does NOT work with Windows" - in many cases it works fine without switching to the alternative version.  I have the full 64-bit version of 12.1.1.4 running on three systems - two Windows 7 and one Windows 8.1 - no issues with either installation or operation on any of them.

  • Issue with spamassassin, now mail not working

    Hi ! I installed spamtrainer almost two months ago. Been feeding the [email protected] for several weeks now , 700 emails each day at least .
    There was very little improvement if none at all. Tried to add "@local_domains_maps = (1)" to amavisd.conf last night thinking it might be the problem , though no virtual domain exist. This was one of the issue on the default Amavisd config. The other one is adding the symbolic link which I already done.
    Computer froze while adding the parameter "@local_domains_maps = (1)", so I manually turn off the Power Mac, then mail stopped altogether. The mails are filing up but the clients couldn't send or receive since this incidence .
    FF is the maincf. and amavis.conf
    All help are greatly appreciated.
    mail:/Users/sysadmin root# postconf -n
    alias_maps = hash:/etc/aliases,hash:/var/mailman/data/aliases
    always_bcc =
    command_directory = /usr/sbin
    config_directory = /etc/postfix
    content_filter = smtp-amavis:[127.0.0.1]:10024
    daemon_directory = /usr/libexec/postfix
    debug_peer_level = 2
    enable_server_options = yes
    html_directory = no
    inet_interfaces = all
    local_recipient_maps = proxy:unix:passwd.byname $alias_maps
    luser_relay =
    mail_owner = postfix
    mailbox_size_limit = 0
    mailbox_transport = cyrus
    mailq_path = /usr/bin/mailq
    manpage_directory = /usr/share/man
    maps_rbl_domains =
    message_size_limit = 31457280
    mydestination = $myhostname,localhost.$mydomain,localhost,mail.cpplaw.com,cpplaw.com
    mydomain = cpplaw.com
    mydomain_fallback = localhost
    myhostname = mail.cpplaw.com
    mynetworks = 127.0.0.1/32,192.168.1.0/24,127.0.0.1
    mynetworks_style = host
    newaliases_path = /usr/bin/newaliases
    owner_request_special = no
    queue_directory = /private/var/spool/postfix
    readme_directory = /usr/share/doc/postfix
    recipient_delimiter = +
    relayhost =
    sample_directory = /usr/share/doc/postfix/examples
    sendmail_path = /usr/sbin/sendmail
    setgid_group = postdrop
    smtpd_client_restrictions = permit_mynetworks permit
    smtpd_tls_key_file =
    unknown_local_recipient_reject_code = 550
    virtual_mailbox_domains =
    virtual_transport = virtual
    mail:/Users/sysadmin root# postconf -n
    alias_maps = hash:/etc/aliases,hash:/var/mailman/data/aliases
    always_bcc =
    command_directory = /usr/sbin
    config_directory = /etc/postfix
    content_filter = smtp-amavis:[127.0.0.1]:10024
    daemon_directory = /usr/libexec/postfix
    debug_peer_level = 2
    enable_server_options = yes
    html_directory = no
    inet_interfaces = all
    local_recipient_maps = proxy:unix:passwd.byname $alias_maps
    luser_relay =
    mail_owner = postfix
    mailbox_size_limit = 0
    mailbox_transport = cyrus
    mailq_path = /usr/bin/mailq
    manpage_directory = /usr/share/man
    maps_rbl_domains =
    message_size_limit = 31457280
    mydestination = $myhostname,localhost.$mydomain,localhost,mail.cpplaw.com,cpplaw.com
    mydomain = cpplaw.com
    mydomain_fallback = localhost
    myhostname = mail.cpplaw.com
    mynetworks = 127.0.0.1/32,192.168.1.0/24,127.0.0.1
    mynetworks_style = host
    newaliases_path = /usr/bin/newaliases
    owner_request_special = no
    queue_directory = /private/var/spool/postfix
    readme_directory = /usr/share/doc/postfix
    recipient_delimiter = +
    relayhost =
    sample_directory = /usr/share/doc/postfix/examples
    sendmail_path = /usr/sbin/sendmail
    setgid_group = postdrop
    smtpd_client_restrictions = permit_mynetworks permit
    smtpd_tls_key_file =
    unknown_local_recipient_reject_code = 550
    virtual_mailbox_domains =
    virtual_transport = virtual
    mail:/Users/sysadmin root#
    _______________________Amavisd.cof_________________________
    use strict;
    # Configuration file for amavisd-new
    # This software is licensed under the GNU General Public License (GPL).
    # See comments at the start of amavisd-new for the whole license text.
    #Sections:
    # Section I - Essential daemon and MTA settings
    # Section II - MTA specific
    # Section III - Logging
    # Section IV - Notifications/DSN, BOUNCE/REJECT/DROP/PASS destiny, quarantine
    # Section V - Per-recipient and per-sender handling, whitelisting, etc.
    # Section VI - Resource limits
    # Section VII - External programs, virus scanners, SpamAssassin
    # Section VIII - Debugging
    #GENERAL NOTES:
    # This file is a normal Perl code, interpreted by Perl itself.
    # - make sure this file (or directory where it resides) is NOT WRITABLE
    # by mere mortals, otherwise it represents a severe security risk!
    # - for values which are interpreted as booleans, it is recommended
    # to use 1 for true, and 0 or undef or '' for false.
    # THIS IS DIFFERENT FROM OLDER AMAVIS VERSIONS where "no" also meant false,
    # now it means true, like any nonempty string does!
    # - Perl syntax applies. Most notably: strings in "" may include variables
    # (which start with $ or @); to include characters @ and $ in double
    # quoted strings, precede them by a backslash; in single-quoted strings
    # the $ and @ lose their special meaning, so it is usually easier to use
    # single quoted strings. Still, in both cases a backslash need to be doubled
    # - variables with names starting with a '@' are lists, the values assigned
    # to them should be lists as well, e.g. ('one@foo', $mydomain, "three");
    # note the comma-separation and parenthesis. If strings in the list
    # do not contain spaces nor variables, a Perl operator qw() may be used
    # as a shorthand to split its argument on whitespace and produce a list
    # of strings, e.g. qw( one@foo example.com three ); Note that the argument
    # to qw is quoted implicitly and no variable interpretation is done within
    # (no '$' variable evaluations). The #-initiated comments can not be used
    # within the string. In other words, $ and # lose their special meaning
    # withing a qw argument, just like within '...' strings.
    # - all e-mail addresses in this file and as used internally by the daemon
    # are in their raw (rfc2821-unquoted and nonbracketed) form, i.e.
    # Bob "Funny" [email protected], not: "Bob \"Funny\" Dude"@example.com
    # and not <"@example.com>; also: '' and not ''.
    # Section I - Essential daemon and MTA settings
    # $MYHOME serves as a quick default for some other configuration settings.
    # More refined control is available with each individual setting further down.
    # $MYHOME is not used directly by the program. No trailing slash!
    #$MYHOME = '/var/lib/amavis'; # (default is '/var/amavis')
    # : $mydomain serves as a quick default for some other configuration settings.
    # : More refined control is available with each individual setting further down.
    # : $mydomain is never used directly by the program.
    $mydomain = 'cpplaw.com'; aol.com'; # (no useful default)
    # Set the user and group to which the daemon will change if started as root
    # (otherwise just keep the UID unchanged, and these settings have no effect):
    $daemon_user = 'clamav'; # (no default; customary: vscan or amavis)
    $daemon_group = 'clamav'; # (no default; customary: vscan or amavis)
    # Runtime working directory (cwd), and a place where
    # temporary directories for unpacking mail are created.
    # (no trailing slash, may be a scratch file system)
    $TEMPBASE = $MYHOME; # (must be set if other config vars use is)
    #$TEMPBASE = "$MYHOME/tmp"; # prefer to keep home dir /var/amavis clean?
    # $helpers_home sets environment variable HOME, and is passed as option
    # 'home_dir_for_helpers' to Mail::SpamAssassin::new. It should be a directory
    # on a normal persistent file system, not a scratch or temporary file system
    #$helpers_home = $MYHOME; # (defaults to $MYHOME)
    #$daemon_chroot_dir = $MYHOME; # (default is undef, meaning: do not chroot)
    #$pid_file = "$MYHOME/amavisd.pid"; # (default is "$MYHOME/amavisd.pid")
    #$lock_file = "$MYHOME/amavisd.lock"; # (default is "$MYHOME/amavisd.lock")
    # set environment variables if you want (no defaults):
    $ENV{TMPDIR} = $TEMPBASE; # wise, but usually not necessary
    # MTA SETTINGS, UNCOMMENT AS APPROPRIATE,
    # both $forward_method and $notify_method default to 'smtp:127.0.0.1:10025'
    # POSTFIX, or SENDMAIL in dual-MTA setup, or EXIM V4
    # (set host and port number as required; host can be specified
    # as IP address or DNS name (A or CNAME, but MX is ignored)
    #$forward_method = 'smtp:127.0.0.1:10025'; # where to forward checked mail
    #$notify_method = $forward_method; # where to submit notifications
    # NOTE: The defaults (above) are good for Postfix or dual-sendmail. You MUST
    # uncomment the approprate settings below if using other setups!
    # SENDMAIL MILTER, using amavis-milter.c helper program:
    #$forward_method = undef; # no explicit forwarding, sendmail does it by itself
    # milter; option -odd is needed to avoid deadlocks
    #$notify_method = 'pipe:flags=q argv=/usr/sbin/sendmail -Ac -i -odd -f ${sender} -- ${recipient}';
    # just a thought: can we use use -Am instead of -odd ?
    # SENDMAIL (old non-milter setup, as relay):
    #$forward_method = 'pipe:flags=q argv=/usr/sbin/sendmail -C/etc/sendmail.orig.cf -i -f ${sender} -- ${recipient}';
    #$notify_method = $forward_method;
    # SENDMAIL (old non-milter setup, amavis.c calls local delivery agent):
    #$forward_method = undef; # no explicit forwarding, amavis.c will call LDA
    #$notify_method = 'pipe:flags=q argv=/usr/sbin/sendmail -Ac -i -f ${sender} -- ${recipient}';
    # EXIM v3 (not recommended with v4 or later, which can use SMTP setup instead):
    #$forward_method = 'pipe:flags=q argv=/usr/sbin/exim -oMr scanned-ok -i -f ${sender} -- ${recipient}';
    #$notify_method = $forward_method;
    # prefer to collect mail for forwarding as BSMTP files?
    #$forward_method = "bsmtp:$MYHOME/out-%i-%n.bsmtp";
    #$notify_method = $forward_method;
    # Net::Server pre-forking settings
    # You may want $max_servers to match the width of your MTA pipe
    # feeding amavisd, e.g. with Postfix the 'Max procs' field in the
    # master.cf file, like the '2' in the: smtp-amavis unix - - n - 2 smtp
    $max_servers = 2; # number of pre-forked children (default 2)
    $max_requests = 10; # retire a child after that many accepts (default 10)
    $child_timeout=5*60; # abort child if it does not complete each task in n sec
    # (default: 8*60 seconds)
    # Check also the settings of @av_scanners at the end if you want to use
    # virus scanners. If not, you may want to delete the whole long assignment
    # to the variable @av_scanners, which will also remove the virus checking
    # code (e.g. if you only want to do spam scanning).
    # Here is a QUICK WAY to completely DISABLE some sections of code
    # that WE DO NOT WANT (it won't even be compiled-in).
    # For more refined controls leave the following two lines commented out,
    # and see further down what these two lookup lists really mean.
    #@bypass_virus_checks_acl = qw( . ); # uncomment to DISABLE anti-virus code
    #@bypass_spam_checks_acl = qw( . ); # uncomment to DISABLE anti-spam code
    # Any setting can be changed with a new assignment, so make sure
    # you do not unintentionally override these settings further down!
    # Lookup list of local domains (see README.lookups for syntax details)
    # NOTE:
    # For backwards compatibility the variable names @local_domains (old) and
    # @local_domains_acl (new) are synonyms. For consistency with other lookups
    # the name @local_domains_acl is now preferred. It also makes it more
    # obviously distinct from the new %local_domains hash lookup table.
    # local_domains* lookup tables are used in deciding whether a recipient
    # is local or not, or in other words, if the message is outgoing or not.
    # This affects inserting spam-related headers for local recipients,
    # limiting recipient virus notifications (if enabled) to local recipients,
    # in deciding if address extension may be appended, and in SQL lookups
    # for non-fqdn addresses. Set it up correctly if you need features
    # that rely on this setting (or just leave empty otherwise).
    # With Postfix (2.0) a quick reminder on what local domains normally are:
    # a union of domains spacified in: $mydestination, $virtual_alias_domains,
    # $virtual_mailbox_domains, and $relay_domains.
    @local_domains_acl = ( ".$mydomain" ); # $mydomain and its subdomains
    # @local_domains_acl = qw(); # default is empty, no recipient treated as local
    # @local_domains_acl = qw( .example.com );
    # @local_domains_acl = qw( .example.com !host.sub.example.net .sub.example.net );
    # @local_domains_acl = ( ".$mydomain", '.example.com', 'sub.example.net' );
    # or alternatively(A), using a Perl hash lookup table, which may be assigned
    # directly, or read from a file, one domain per line; comments and empty lines
    # are ignored, a dot before a domain name implies its subdomains:
    #read_hash(\%local_domains, '/var/amavis/local_domains');
    #or alternatively(B), using a list of regular expressions:
    # $local_domains_re = new_RE( qr'[@.]example\.com$'i );
    # see README.lookups for syntax and semantics
    # Section II - MTA specific (defaults should be ok)
    # if $relayhost_is_client is true, IP address in $notify_method and
    # $forward_method is dynamically overridden with SMTP client peer address
    # if available, which makes possible for several hosts to share one daemon
    #$relayhost_is_client = 1; # (defaults to false)
    #$insert_received_line = 1; # behave like MTA: insert 'Received:' header
    # (does not apply to sendmail/milter)
    # (default is true)
    # AMAVIS-CLIENT PROTOCOL INPUT SETTINGS (e.g. with sendmail milter)
    # (used with amavis helper clients like amavis-milter.c and amavis.c,
    # NOT needed for Postfix and Exim)
    $unix_socketname = "$MYHOME/amavisd.sock"; # amavis helper protocol socket
    #$unix_socketname = undef; # disable listening on a unix socket
    # (default is undef, i.e. disabled)
    # (usual setting is $MYHOME/amavisd.sock)
    # Do we receive quoted or raw addresses from the helper program?
    # (does not apply to SMTP; defaults to true)
    #$gets_addr_in_quoted_form = 1; # "Bob \"Funny\" Dude"@example.com
    #$gets_addr_in_quoted_form = 0; # Bob "Funny" [email protected]
    # SMTP SERVER (INPUT) PROTOCOL SETTINGS (e.g. with Postfix, Exim v4, ...)
    # (used when MTA is configured to pass mail to amavisd via SMTP or LMTP)
    $inet_socket_port = 10024; # accept SMTP on this local TCP port
    # (default is undef, i.e. disabled)
    # multiple ports may be provided: $inet_socket_port = [10024, 10026, 10028];
    # SMTP SERVER (INPUT) access control
    # - do not allow free access to the amavisd SMTP port !!!
    # when MTA is at the same host, use the following (one or the other or both):
    #$inet_socket_bind = '127.0.0.1'; # limit socket bind to loopback interface
    # (default is '127.0.0.1')
    @inet_acl = qw( 127.0.0.1 ); # allow SMTP access only from localhost IP
    # (default is qw( 127.0.0.1 ) )
    # when MTA (one or more) is on a different host, use the following:
    #@inet_acl = qw(127/8 10.1.0.1 10.1.0.2); # adjust the list as appropriate
    #$inet_socket_bind = undef; # bind to all IP interfaces
    # Example1:
    # @inet_acl = qw( 127/8 10/8 172.16/12 192.168/16 );
    # permit only SMTP access from loopback and rfc1918 private address space
    # Example2:
    # @inet_acl = qw( !192.168.1.12 172.16.3.3 !172.16.3/255.255.255.0
    # 127.0.0.1 10/8 172.16/12 192.168/16 );
    # matches loopback and rfc1918 private address space except host 192.168.1.12
    # and net 172.16.3/24 (but host 172.16.3.3 within 172.16.3/24 still matches)
    # Example3:
    # @inet_acl = qw( 127/8
    # !172.16.3.0 !172.16.3.127 172.16.3.0/25
    # !172.16.3.128 !172.16.3.255 172.16.3.128/25 );
    # matches loopback and both halves of the 172.16.3/24 C-class,
    # split into two subnets, except all four broadcast addresses
    # for these subnets
    # See README.lookups for details on specifying access control lists.
    # Section III - Logging
    # true (e.g. 1) => syslog; false (e.g. 0) => logging to file
    $DO_SYSLOG = 0; # (defaults to false)
    #$SYSLOG_LEVEL = 'user.info'; # (defaults to 'mail.info')
    # Log file (if not using syslog)
    $LOGFILE = "/var/log/amavis.log"; # (defaults to empty, no log)
    #NOTE: levels are not strictly observed and are somewhat arbitrary
    # 0: startup/exit/failure messages, viruses detected
    # 1: args passed from client, some more interesting messages
    # 2: virus scanner output, timing
    # 3: server, client
    # 4: decompose parts
    # 5: more debug details
    $log_level = 4; # (defaults to 0)
    # Customizeable template for the most interesting log file entry (e.g. with
    # $log_level=0) (take care to properly quote Perl special characters like '\')
    # For a list of available macros see README.customize .
    # only log infected messages (useful with log level 0):
    # $log_templ = '[? %#V |[? %#F ||banned filename ([%F|,])]|infected ([%V|,])]#
    # [? %#V |[? %#F ||, from=<%o>, to=[<%R>|,][? %i ||, quarantine %i]]#
    # |, from=<%o>, to=[<%R>|,][? %i ||, quarantine %i]]';
    # log both infected and noninfected messages (default):
    $log_templ = '[? %#V |[? %#F |[?%#D|Not-Delivered|Passed]|BANNED name/type (%F)]|INFECTED (%V)], #
    <%o> -> [<%R>|,][? %i ||, quarantine %i], Message-ID: %m, Hits: %c';
    # Section IV - Notifications/DSN, BOUNCE/REJECT/DROP/PASS destiny, quarantine
    # Select notifications text encoding when Unicode-aware Perl is converting
    # text from internal character representation to external encoding (charset
    # in MIME terminology)
    # to be used in RFC 2047-encoded header field bodies, e.g. in Subject:
    #$hdr_encoding = 'iso-8859-1'; # (default: 'iso-8859-1')
    # to be used in notification body text: its encoding and Content-type.charset
    #$bdy_encoding = 'iso-8859-1'; # (default: 'iso-8859-1')
    # Default template texts for notifications may be overruled by directly
    # assigning new text to template variables, or by reading template text
    # from files. A second argument may be specified in a call to read_text(),
    # specifying character encoding layer to be used when reading from the
    # external file, e.g. 'utf8', 'iso-8859-1', or often just $bdy_encoding.
    # Text will be converted to internal character representation by Perl 5.8.0
    # or later; second argument is ignored otherwise. See PerlIO::encoding,
    # Encode::PerlIO and perluniintro man pages.
    # $notify_sender_templ = read_text('/var/amavis/notify_sender.txt');
    # $notify_virus_sender_templ= read_text('/var/amavis/notify_virus_sender.txt');
    # $notify_virus_admin_templ = read_text('/var/amavis/notify_virus_admin.txt');
    # $notify_virus_recips_templ= read_text('/var/amavis/notify_virus_recips.txt');
    # $notify_spam_sender_templ = read_text('/var/amavis/notify_spam_sender.txt');
    # $notify_spam_admin_templ = read_text('/var/amavis/notify_spam_admin.txt');
    # If notification template files are collectively available in some directory,
    # use read_l10n_templates which calls read_text for each known template.
    # read_l10n_templates('/etc/amavis/en_US');
    # Here is an overall picture (sequence of events) of how pieces fit together
    # (only virus controls are shown, spam controls work the same way):
    # bypass_virus_checks set for all recipients? ==> PASS
    # no viruses? ==> PASS
    # log virus if $log_templ is nonempty
    # quarantine if $virus_quarantine_to is nonempty
    # notify admin if $virus_admin (lookup) nonempty
    # notify recips if $warnvirusrecip and (recipient is local or $warn_offsite)
    # add address extensions for local recipients (when enabled)
    # send (non-)delivery notifications
    # to sender if DSN needed (BOUNCE) or ($warnvirussender and D_PASS)
    # virus_lovers or final_destiny==D_PASS ==> PASS
    # DISCARD (2xx) or REJECT (5xx) (depending on final_*_destiny)
    # Equivalent flow diagram applies for spam checks.
    # If a virus is detected, spam checking is skipped entirely.
    # The following symbolic constants can be used in *destiny settings:
    # D_PASS mail will pass to recipients, regardless of bad contents;
    # D_DISCARD mail will not be delivered to its recipients, sender will NOT be
    # notified. Effectively we lose mail (but will be quarantined
    # unless disabled). Not a decent thing to do for a mailer.
    # D_BOUNCE mail will not be delivered to its recipients, a non-delivery
    # notification (bounce) will be sent to the sender by amavisd-new;
    # Exception: bounce (DSN) will not be sent if a virus name matches
    # $viruses_that_fake_sender_re, or to messages from mailing lists
    # (Precedence: bulk|list|junk);
    # D_REJECT mail will not be delivered to its recipients, sender should
    # preferably get a reject, e.g. SMTP permanent reject response
    # (e.g. with milter), or non-delivery notification from MTA
    # (e.g. Postfix). If this is not possible (e.g. different recipients
    # have different tolerances to bad mail contents and not using LMTP)
    # amavisd-new sends a bounce by itself (same as D_BOUNCE).
    # Notes:
    # D_REJECT and D_BOUNCE are similar, the difference is in who is responsible
    # for informing the sender about non-delivery, and how informative
    # the notification can be (amavisd-new knows more than MTA);
    # With D_REJECT, MTA may reject original SMTP, or send DSN (delivery status
    # notification, colloquially called 'bounce') - depending on MTA;
    # Best suited for sendmail milter, especially for spam.
    # With D_BOUNCE, amavisd-new (not MTA) sends DSN (can better explain the
    # reason for mail non-delivery, but unable to reject the original
    # SMTP session). Best suited to reporting viruses, and for Postfix
    # and other dual-MTA setups, which can't reject original client SMTP
    # session, as the mail has already been enqueued.
    $final_virus_destiny = D_BOUNCE; # (defaults to D_BOUNCE)
    $final_banned_destiny = D_BOUNCE; # (defaults to D_BOUNCE)
    $final_spam_destiny = D_PASS; # (defaults to D_REJECT)
    $final_bad_header_destiny = D_PASS; # (defaults to D_PASS), D_BOUNCE suggested
    # Alternatives to consider for spam:
    # - use D_PASS if clients will do filtering based on inserted mail headers;
    # - use D_DISCARD, if kill_level is set safely high;
    # - use D_BOUNCE instead of D_REJECT if not using milter;
    # There are no sensible alternatives to D_BOUNCE for viruses, but consider:
    # - use D_PASS (or virus_lovers) and $warnvirussender=1 to deliver viruses;
    # - use D_REJECT instead of D_BOUNCE if using milter and under heavy
    # virus storm;
    # Don't bother to set both D_DISCARD and $warn*sender=1, it will get mapped
    # to D_BOUNCE.
    # The separation of *_destiny values into D_BOUNCE, D_REJECT, D_DISCARD
    # and D_PASS made settings $warnvirussender and $warnspamsender only still
    # useful with D_PASS.
    # The following $warn*sender settings are ONLY used when mail is
    # actually passed to recipients ($final_*_destiny=D_PASS, or *_lovers*).
    # Bounces or rejects produce non-delivery status notification anyway.
    # Notify virus sender?
    #$warnvirussender = 1; # (defaults to false (undef))
    # Notify spam sender?
    #$warnspamsender = 1; # (defaults to false (undef))
    # Notify sender of banned files?
    #$warnbannedsender = 1; # (defaults to false (undef))
    # Notify sender of syntactically invalid header containing non-ASCII characters?
    #$warnbadhsender = 1; # (defaults to false (undef))
    # Notify virus (or banned files) RECIPIENT?
    # (not very useful, but some policies demand it)
    #$warnvirusrecip = 1; # (defaults to false (undef))
    #$warnbannedrecip = 1; # (defaults to false (undef))
    # Notify also non-local virus/banned recipients if $warn*recip is true?
    # (including those not matching local_domains*)
    #$warn_offsite = 1; # (defaults to false (undef), i.e. only notify locals)
    # Treat envelope sender address as unreliable and don't send sender
    # notification / bounces if name(s) of detected virus(es) match the list.
    # Note that virus names are supplied by external virus scanner(s) and are
    # not standardized, so virus names may need to be adjusted.
    # See README.lookups for syntax.
    $viruses_that_fake_sender_re = new_RE(
    qr'nimda|hybris|klez|bugbear|yaha|braid|sobig|fizzer|palyh|peido|holar'i );
    # where to send ADMIN VIRUS NOTIFICATIONS (should be a fully qualified address)
    # - the administrator address may be a simple fixed e-mail address (a scalar),
    # or may depend on the SENDER address (e.g. its domain), in which case
    # a ref to a hash table can be specified (specify lower-cased keys,
    # dot is a catchall, see README.lookups).
    # Empty or undef lookup disables virus admin notifications.
    $virus_admin = '[email protected]';
    # $virus_admin = undef; # do not send virus admin notifications (default)
    # $virus_admin = {'not.example.com' => '', '.' => '[email protected]'};
    # $virus_admin = '[email protected]';
    # equivalent to $virus_admin, but for spam admin notifications:
    #$spam_admin = '[email protected]';# $spam_admin = undef; # do not send spam admin notifications (default)
    # $spam_admin = {'not.example.com' => '', '.' => '[email protected]'};
    #advanced example, using a hash lookup table:
    # - $virus_admin = {
    # '[email protected]' => '[email protected]',
    # '.sub1.example.com' => '[email protected]',
    # '.sub2.example.com' => '', # don't send admin notifications
    # 'a.sub3.example.com' => '[email protected]',
    # '.sub3.example.com' => '[email protected]',
    # '.example.com' => '[email protected]', # catchall for our virus senders
    # '.' => '[email protected]', # catchall for the rest
    # whom notification reports are sent from (ENVELOPE SENDER);
    # may be a null reverse path, or a fully qualified address:
    # (admin and recip sender addresses default to $mailfrom
    # for compatibility, which in turn defaults to undef (empty) )
    # If using strings in double quotes, don't forget to quote @, i.e. \@
    $mailfrom_notify_admin = "virusalert\@$mydomain";
    $mailfrom_notify_recip = "virusalert\@$mydomain";
    $mailfrom_notify_spamadmin = "spam.police\@$mydomain";
    # 'From' HEADER FIELD for sender and admin notifications.
    # This should be a replyable address, see rfc1894. Not to be confused
    # with $mailfrom_notify_sender, which is the envelope address and
    # should be empty (null reverse path) according to rfc2821.
    # $hdrfrom_notify_sender = "amavisd-new <postmaster\@$mydomain>";
    # $hdrfrom_notify_sender = 'amavisd-new <[email protected]>';
    # (defaults to: "amavisd-new <postmaster\@$myhostname>")
    # $hdrfrom_notify_admin = $mailfrom_notify_admin;
    # (defaults to: $mailfrom_notify_admin)
    # $hdrfrom_notify_spamadmin = $mailfrom_notify_spamadmin;
    # (defaults to: $mailfrom_notify_spamadmin)
    # whom quarantined messages appear to be sent from (envelope sender)
    $mailfrom_to_quarantine = undef; # original sender if undef, or set explicitly
    # (default is undef)
    # Location to put infected mail into: (applies to 'local:' quarantine method)
    # empty for not quarantining, may be a file (mailbox),
    # or a directory (no trailing slash)
    # (the default value is undef, meaning no quarantine)
    $QUARANTINEDIR = '/var/virusmails';
    #$virus_quarantine_method = "local:virus-%i-%n"; # default
    #$spam_quarantine_method = "local:spam-%b-%i-%n"; # default
    #use the new 'bsmtp:' method as an alternative to the default 'local:'
    #$virus_quarantine_method = "bsmtp:$QUARANTINEDIR/virus-%i-%n.bsmtp";
    #$spam_quarantine_method = "bsmtp:$QUARANTINEDIR/spam-%b-%i-%n.bsmtp";
    # When using the 'local:' quarantine method (default), the following applies:
    # A finer control of quarantining is available through variable
    # $virus_quarantine_to/$spam_quarantine_to. It may be a simple scalar string,
    # or a ref to a hash lookup table, or a regexp lookup table object,
    # which makes possible to set up per-recipient quarantine addresses.
    # The value of scalar $virus_quarantine_to/$spam_quarantine_to (or a
    # per-recipient lookup result from the hash table %$virus_quarantine_to)
    # is/are interpreted as follows:
    # VARIANT 1:
    # empty or undef disables quarantine;
    # VARIANT 2:
    # a string NOT containg an '@';
    # amavisd will behave as a local delivery agent (LDA) and will quarantine
    # viruses to local files according to hash %local_delivery_aliases (pseudo
    # aliases map) - see subroutine mail_to_local_mailbox() for details.
    # Some of the predefined aliases are 'virus-quarantine' and 'spam-quarantine'.
    # Setting $virus_quarantine_to ($spam_quarantine_to) to this string will:
    # * if $QUARANTINEDIR is a directory, each quarantined virus will go
    # to a separate file in the $QUARANTINEDIR directory (traditional
    # amavis style, similar to maildir mailbox format);
    # * otherwise $QUARANTINEDIR is treated as a file name of a Unix-style
    # mailbox. All quarantined messages will be appended to this file.
    # Amavisd child process must obtain an exclusive lock on the file during
    # delivery, so this may be less efficient than using individual files
    # or forwarding to MTA, and it may not work across NFS or other non-local
    # file systems (but may be handy for pickup of quarantined files via IMAP
    # for example);
    # VARIANT 3:
    # any email address (must contain '@').
    # The e-mail messages to be quarantined will be handed to MTA
    # for delivery to the specified address. If a recipient address local to MTA
    # is desired, you may leave the domain part empty, e.g. 'infected@', but the
    # '@' character must nevertheless be included to distinguish it from variant 2.
    # This method enables more refined delivery control made available by MTA
    # (e.g. its aliases file, other local delivery agents, dealing with
    # privileges and file locking when delivering to user's mailbox, nonlocal
    # delivery and forwarding, fan-out lists). Make sure the mail-to-be-quarantined
    # will not be handed back to amavisd for checking, as this will cause a loop
    # (hopefully broken at some stage)! If this can be assured, notifications
    # will benefit too from not being unecessarily virus-scanned.
    # By default this is safe to do with Postfix and Exim v4 and dual-sendmail
    # setup, but probably not safe with sendmail milter interface without
    # precaution.
    # (the default value is undef, meaning no quarantine)
    #$virus_quarantine_to = '[email protected]'; # traditional local quarantine
    #$virus_quarantine_to = 'infected@'; # forward to MTA for delivery
    #$virus_quarantine_to = "virus-quarantine\@$mydomain"; # similar
    #$virus_quarantine_to = '[email protected]'; # similar
    #$virus_quarantine_to = undef; # no quarantine
    #$virus_quarantine_to = new_RE( # per-recip multiple quarantines
    # [qr'^user@example\.com$'i => 'infected@'],
    # [qr'^(.*)@example\.com$'i => 'virus-${1}@example.com'],
    # [qr'^(.*)(@[^@])?$'i => 'virus-${1}${2}'],
    # [qr/.*/ => 'virus-quarantine'] );
    # similar for spam
    # (the default value is undef, meaning no quarantine)
    #$spam_quarantine_to = '[email protected]';
    #$spam_quarantine_to = "spam-quarantine\@$mydomain";
    #$spam_quarantine_to = new_RE( # per-recip multiple quarantines
    # [qr'^(.*)@example\.com$'i => 'spam-${1}@example.com'],
    # [qr/.*/ => 'spam-quarantine'] );
    # In addition to per-recip quarantine, a by-sender lookup is possible. It is
    # similar to $spam_quarantine_to, but the lookup key is the sender address:
    #$spam_quarantine_bysender_to = undef; # dflt: no by-sender spam quarantine
    # Add X-Virus-Scanned header field to mail?
    $X_HEADER_TAG = 'X-Virus-Scanned'; # (default: undef)
    # Leave empty to add no header field # (default: undef)
    $X_HEADER_LINE = "by amavisd-new at $mydomain";
    $remove_existing_x_scanned_headers = 0; # leave existing X-Virus-Scanned alone
    #$remove_existing_x_scanned_headers= 1; # remove existing headers
    # (defaults to false)
    $remove_existing_spam_headers = 0; # leave existing X-Spam* headers alone
    #$remove_existing_spam_headers = 1; # remove existing spam headers if
    # spam scanning is enabled (default)
    # set $bypass_decode_parts to true if you only do spam scanning, or if you
    # have a good virus scanner that can deal with compression and recursively
    # unpacking archives by itself, and save amavisd the trouble.
    # Disabling decoding also causes banned_files checking to only see
    # MIME names and MIME content types, not the content classification types
    # as provided by the file(1) utility.
    # It is a double-edged sword, make sure you know what you are doing!
    #$bypass_decode_parts = 1; # (defaults to false)
    # don't trust this file type or corresponding unpacker for this file type,
    # keep both the original and the unpacked file
    # (lookup key is what file(1) utility returned):
    $keep_decoded_original_re = new_RE(
    qr'^(ASCII|text|uuencoded|xxencoded|binhex)'i,
    # Checking for banned MIME types and names. If any mail part matches,
    # the whole mail is rejected, much like the way viruses are handled.
    # A list in object $banned_filename_re can be defined to provide a list
    # of Perl regular expressions to be matched against each part's:
    # * Content-Type value (both declared and effective mime-type),
    # including the possible security risk content types
    # message/partial and message/external-body, as specified by rfc2046;
    # * declared (recommended) file names as specified by MIME subfields
    # Content-Disposition.filename and Content-Type.name, both in their
    # raw (encoded) form and in rfc2047-decoded form if applicable;
    # * file content type as guessed by 'file(1)' utility, both the raw result
    # from file(1), as well as short type name, classified into names such as
    # .asc, .txt, .html, .doc, .jpg, .pdf, .zip, .exe, ..., which is always
    # beginning with a dot - see subroutine determine_file_types().
    # This step is done only if $bypass_decode_parts is not true.
    # * leave $banned_filename_re undefined to disable these checks
    # (giving an empty list to new_RE() will also always return false)
    $banned_filename_re = new_RE(
    qr'\.[a-zA-Z][a-zA-Z0-9]{0,3}\.(vbs|pif|scr|bat|com|exe|dll)$'i, # double extension
    # qr'.\.(exe|vbs|pif|scr|bat|com)$'i, # banned extension - basic
    # qr'.\.(ade|adp|bas|bat|chm|cmd|com|cpl|crt|exe|hlp|hta|inf|ins|isp|js|
    # jse|lnk|mdb|mde|msc|msi|msp|mst|pcd|pif|reg|scr|sct|shs|shb|vb|
    # vbe|vbs|wsc|wsf|wsh)$'ix, # banned extension - long
    # qr'^\.(exe|zip|lha|tnef)$'i, # banned file(1) types
    # qr'^application/x-msdownload$'i, # banned MIME types
    # qr'^message/partial$'i, qr'^message/external-body$'i, # rfc2046
    # See http://support.microsoft.com/default.aspx?scid=kb;EN-US;q262631
    # and http://www.cknow.com/vtutor/vtextensions.htm
    # A little trick: a pattern qr'\.exe$' matches both a short type name '.exe',
    # as well as any file name which happens to end with .exe. If only matching
    # a file name is desired, but not the short name, a pattern qr'.\.exe$'i
    # or similar may be used, which requires that at least one character preceeds
    # the '.exe', and so it will never match short file types, which always start
    # with a dot.
    # Section V - Per-recipient and per-sender handling, whitelisting, etc.
    # %virus_lovers, @virus_lovers_acl and $virus_lovers_re lookup tables:
    # (these should be considered policy options, they do not disable checks,
    # see bypas*checks for that!)
    # Exclude certain RECIPIENTS from virus filtering by adding their lower-cased
    # envelope e-mail address (or domain only) to the hash %virus_lovers, or to
    # the access list @virus_lovers_acl - see README.lookups and examples.
    # Make sure the appropriate form (e.g. external/internal) of address
    # is used in case of virtual domains, or when mapping external to internal
    # addresses, etc. - this is MTA-specific.
    # Notifications would still be generated however (see the overall
    # picture above), and infected mail (if passed) gets additional header:
    # X-AMaViS-Alert: INFECTED, message contains virus: ...
    # (header not inserted with milter interface!)
    # NOTE (milter interface only): in case of multiple recipients,
    # it is only possible to drop or accept the message in its entirety - for all
    # recipients. If all of them are virus lovers, we'll accept mail, but if
    # at least one recipient is not a virus lover, we'll discard the message.
    # %bypass_virus_checks, @bypass_virus_checks_acl and $bypass_virus_checks_re
    # lookup tables:
    # (this is mainly a time-saving option, unlike virus_lovers* !)
    # Similar in concept to %virus_lovers, a hash %bypass_virus_checks,
    # access list @bypass_virus_checks_acl and regexp list $bypass_virus_checks_re
    # are used to skip entirely the decoding, unpacking and virus checking,
    # but only if ALL recipients match the lookup.
    # %bypass_virus_checks/@bypass_virus_checks_acl/$bypass_virus_checks_re
    # do NOT GUARANTEE the message will NOT be checked for viruses - this may
    # still happen when there is more than one recipient for a message, and
    # not all of them match these lookup tables. To guarantee virus delivery,
    # a recipient must also match %virus_lovers/@virus_lovers_acl lookups
    # (but see milter limitations above),
    # NOTE: it would not be clever to base virus checks on SENDER address,
    # since there are no guarantees that it is genuine. Many viruses
    # and spam messages fake sender address. To achieve selective filtering
    # based on the source of the mail (e.g. IP address, MTA port number, ...),
    # use mechanisms provided by MTA if available.
    # Similar to lookup tables controlling virus checking, there exist
    # spam scanning, banned names/types, and headers_checks control counterparts:
    # %spam_lovers, @spam_lovers_acl, $spam_lovers_re
    # %banned_files_lovers, @banned_files_lovers_acl, $banned_files_lovers_re
    # %bad_header_lovers, @bad_header_lovers_acl, $bad_header_lovers_re
    # and:
    # %bypass_spam_checks/@bypass_spam_checks_acl/$bypass_spam_checks_re
    # %bypass_banned_checks/@bypass_banned_checks_acl/$bypass_banned_checks_re
    # %bypass_header_checks/@bypass_header_checks_acl/$bypass_header_checks_re
    # See README.lookups for details about the syntax.
    # The following example disables spam checking altogether,
    # since it matches any recipient e-mail address (any address
    # is a subdomain of the top-level root DNS domain):
    # @bypass_spam_checks_acl = qw( . );
    # @bypass_header_checks_acl = qw( [email protected] );
    # @bad_header_lovers_acl = qw( [email protected] );
    # See README.lookups for further detail, and examples below.
    # $virus_lovers{lc("postmaster\@$mydomain")} = 1;
    # $virus_lovers{lc('[email protected]')} = 1;
    # $virus_lovers{lc('[email protected]')} = 1;
    # $virus_lovers{lc('some.user@')} = 1; # this recipient, regardless of domain
    # $virus_lovers{lc('[email protected]')} = 0; # never, even if domain matches
    # $virus_lovers{lc('example.com')} = 1; # this domain, but not its subdomains
    # $virus_lovers{lc('.example.com')}= 1; # this domain, including its subdomains
    #or:
    # @virus_lovers_acl = qw( [email protected] !lab.xxx.com .xxx.com yyy.org );
    # $bypass_virus_checks{lc('[email protected]')} = 1;
    # @bypass_virus_checks_acl = qw( some.ddd !butnot.example.com .example.com );
    # @virus_lovers_acl = qw( [email protected] );
    # $virus_lovers_re = new_RE( qr'(helpdesk|postmaster)@example\.com$'i );
    # $spam_lovers{lc("postmaster\@$mydomain")} = 1;
    # $spam_lovers{lc('[email protected]')} = 1;
    # $spam_lovers{lc('[email protected]')} = 1;
    # @spam_lovers_acl = qw( !.example.com );
    # $spam_lovers_re = new_RE( qr'^user@example\.com$'i );
    # don't run spam check for these RECIPIENT domains:
    # @bypass_spam_checks_acl = qw( d1.com .d2.com a.d3.com );
    # or the other way around (bypass check for all BUT these):
    # @bypass_spam_checks_acl = qw( !d1.com !.d2.com !a.d3.com . );
    # a practical application: don't check outgoing mail for spam:
    # @bypass_spam_checks_acl = ( "!.$mydomain", "." );
    # (a downside of which is that such mail will not count as ham in SA bayes db)
    # Where to find SQL server(s) and database to support SQL lookups?
    # A list of triples: (dsn,user,passw). (dsn = data source name)
    # Specify more than one for multiple (backup) SQL servers.
    # See 'man DBI', 'man DBD::mysql', 'DBD::Pg', ... for details.
    # @lookup_sql_dsn =
    # ( ['DBI:mysql:mail:host1', 'some-username1', 'some-password1'],
    # ['DBI:mysql:mail:host2', 'some-username2', 'some-password2'] );
    # ('mail' in the example is the database name, choose what you like)
    # With PostgreSQL the dsn (first element of the triple) may look like:
    # 'DBI:Pg:host=host1;dbname=mail'
    # The SQL select clause to fetch per-recipient policy settings.
    # The %k will be replaced by a comma-separated list of query addresses
    # (e.g. full address, domain only, catchall). Use ORDER, if there
    # is a chance that multiple records will match - the first match wins.
    # If field names are not unique (e.g. 'id'), the later field overwrites the
    # earlier in a hash returned by lookup, which is why we use '*,users.id'.
    # No need to uncomment the following assignment if the default is ok.
    # $sql_select_policy = 'SELECT *,users.id FROM users,policy'.
    # ' WHERE (users.policy_id=policy.id) AND (users.email IN (%k))'.
    # ' ORDER BY users.priority DESC';
    # The SQL select clause to check sender in per-recipient whitelist/blacklist
    # The first SELECT argument '?' will be users.id from recipient SQL lookup,
    # the %k will be sender addresses (e.g. full address, domain only, catchall).
    # The default value is:
    # $sql_select_white_black_list = 'SELECT wb FROM wblist,mailaddr'.
    # ' WHERE (rid=?) AND (sid=mailaddr.id) AND (mailaddr.email IN (%k))'.
    # ' ORDER BY mailaddr.priority DESC';
    # To disable SQL white/black list, set to undef (otherwise comment-out
    # the following statement, leaving it at the default value):
    $sql_select_white_black_list = undef; # undef disables SQL white/blacklisting
    # If you decide to pass viruses (or spam) to certain recipients using the
    # above lookup tables or using $final_virus_destiny=1, you can set
    # the variable $addr_extension_virus ($addr_extension_spam) to some
    # string, and the recipient address will have this string appended
    # as an address extension to the local-part of the address. This extension
    # can be used by final local delivery agent to place such mail in different
    # folders. Leave these two variables undefined or empty strings to prevent
    # appending address extensions. Setting has no effect on recipient which will
    # not be receiving viruses/spam. Recipients who do not match lookup tables
    # local_domains* are not affected.
    # LDAs usually default to stripping away address extension if no special
    # handling is specified, so having this option enabled normally does no harm,
    # provided the $recipients_delimiter matches the setting on the final
    # MTA's LDA.
    # $addr_extension_virus = 'virus'; # (default is undef, same as empty)
    # $addr_extension_spam = 'spam'; # (default is undef, same as empty)
    # $addr_extension_banned = 'banned'; # (default is undef, same as empty)
    # Delimiter between local part of the recipient address and address extension
    # (which can optionally be added, see variables $addr_extension_virus and
    # $addr_extension_spam). E.g. recipient address <[email protected]> gets changed
    # to <[email protected]>.
    # Delimiter should match equivalent (final) MTA delimiter setting.
    # (e.g. for Postfix add 'recipient_delimiter = +' to main.cf)
    # Setting it to an empty string or to undef disables this feature
    # regardless of $addr_extension_virus and $addr_extension_spam settings.
    $recipient_delimiter = '+'; # (default is '+')
    # true: replace extension; false: append extension
    # $replace_existing_extension = 1; # (default is false)
    # Affects matching of localpart of e-mail addresses (left of '@')
    # in lookups: true = case sensitive, false = case insensitive
    $localpart_is_case_sensitive = 0; # (default is false)
    # ENVELOPE SENDER WHITELISTING / BLACKLISTING - GLOBAL (RECIPIENT-INDEPENDENT)
    # WHITELISTING: use ENVELOPE SENDER lookups to ENSURE DELIVERY from whitelisted
    # senders even if the message is recognized as spam. Effectively, for the
    # specified senders, message RECIPIENTS temporarily become 'spam_lovers', with
    # further processing being the same as otherwise specified for spam lovers.
    # It does not turn off inserting spam-related headers, if they are enabled.
    # BLACKLISTING: messages from specified SENDERS are DECLARED SPAM.
    # Effectively, for messages from blacklisted senders, spam level
    # is artificially pushed high, and the normal spam processing applies,
    # resulting in 'X-Spam-Flag: YES', high 'X-Spam-Level' bar and other usual
    # reactions to spam, including possible rejection. If the message nevertheless
    # still passes (e.g. for spam loving recipients), it is tagged as BLACKLISTED
    # in the 'X-Spam-Status' header field, but the reported spam value and
    # set of tests in this report header field (if available from SpamAssassin,
    # which may have not been called) is not adjusted.
    # A sender may be both white- and blacklisted at the same time,
    # settings are independent. For example, being both white- and blacklisted,
    # message is delivered to recipients, but is tagged as spam.
    # If ALL recipients of the message either white- or blacklist the sender,
    # spam scanning (calling the SpamAssassin) is bypassed, saving on time.
    # The following variables (lookup tables) are available, with the semantics
    # and syntax as specified in README.lookups:
    # %whitelist_sender, @whitelist_sender_acl, $whitelist_sender_re
    # %blacklist_sender, @blacklist_sender_acl, $blacklist_sender_re
    # SOME EXAMPLES:
    #ACL:
    # @whitelist_sender_acl = qw( .example.com );
    # @whitelist_sender_acl = ( ".$mydomain" ); # $mydomain and its subdomains
    # NOTE: This is not a reliable way of turning off spam checks for
    # locally-originating mail, as sender address can easily be faked.
    # To reliably avoid spam-scanning outgoing mail,
    # use @bypass_spam_checks_acl .
    #RE:
    # $whitelist_sender_re = new_RE(
    # qr'^postmaster@.*\bexample\.com$'i,
    # qr'^owner-[^@]*@'i, qr'-request@'i,
    # qr'\.example\.com$'i );
    $blacklist_sender_re = new_RE(
    qr'^(bulkmail|offers|cheapbenefits|earnmoney|foryou|greatcasino)@'i,
    qr'^(investments|lose_weight_today|market.alert|money2you|MyGreenCard)@'i,
    qr'^(new\.tld\.registry|opt-out|opt-in|optin|saveonlsmoking2002k)@'i,
    qr'^(specialoffer|specialoffers|stockalert|stopsnoring|wantsome)@'i,
    qr'^(workathome|yesitsfree|your_friend|greatoffers)@'i,
    qr'^(inkjetplanet|marketopt|MakeMoney)\d*@'i,
    #HASH lookup variant:
    # NOTE: Perl operator qw splits its argument string by whitespace
    # and produces a list. This means that addresses can not contain
    # whitespace, and there is no provision for comments within the string.
    # You can use the normal Perl list syntax if you have special requirements,
    # e.g. map {...} ('one user@bla', '.second.com'), or use read_hash to read
    # addresses from a file.
    # a hash lookup table can be read from a file,
    # one address per line, comments and empty lines are permitted:
    # read_hash(\%whitelist_sender, '/var/amavis/whitelist_sender');
    # ... or set directly:
    # $whitelist_sender{''} = 1; # don't spam-check MTA bounces
    map { $whitelist_sender{lc($_)}=1 } (qw(
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    [email protected]
    returns.groups.yahoo.com
    # ENVELOPE SENDER WHITELISTING / BLACKLISTING - PER-RECIPIENT
    # The same semantics as for global white/blacklisting applies, but this
    # time each recipient (or its domain, or subdomain, ...) can be given
    # an individual lookup table for matching senders. The per-recipient lookups
    # override the global lookups, which serve as a fallback default.
    # Specify a two-level lookup table: the key for the outer table is recipient,
    # and the result should be an inner lookup table (hash or ACL or RE),
    # where the key used will be the sender.
    #$per_recip_blacklist_sender_lookup_tables = {
    # '[email protected]'=>new_RE(qr'^(inkjetplanet|marketopt|MakeMoney)\d*@'i),
    # '[email protected]'=>[qw( [email protected],org .d2.example,org )],
    #$per_recip_whitelist_sender_lookup_tables = {
    # '[email protected]' => [qw( [email protected] .other.example.org )],
    # '.my1.example.com' => [qw( !foe.other.example,org .other.example,org )],
    # '.my2.example.com' => read_hash('/var/amavis/my2-wl.dat'),
    # 'abuse@' => { 'postmaster@'=>1,
    # '[email protected]'=>1, '[email protected]'=>1 },
    # Section VI - Resource limits
    # Sanity limit to the number of allowed recipients per SMTP transaction
    # $smtpd_recipient_limit = 1000; # (default is 1000)
    # Resource limitations to protect against mail bombs (e.g. 42.zip)
    # Maximum recursion level for extraction/decoding (0 or undef disables limit)
    $MAXLEVELS = 14; # (default is undef, no limit)
    # Maximum number of extracted files (0 or undef disables the limit)
    $MAXFILES = 1500; # (default is undef, no limit)
    # For the cumulative total of all decoded mail parts we set max storage size
    # to defend against mail bombs. Even though parts may be deleted (replaced
    # by decoded text) during decoding, the size they occupied is _not_ returned
    # to the quota pool.
    # Parameters to storage quota formula for unpacking/decoding/decompressing
    # Formula:
    # quota = max($MIN_EXPANSION_QUOTA,
    # $mail_size*$MIN_EXPANSION_FACTOR,
    # min($MAX_EXPANSION_QUOTA, $mail_size*$MAX_EXPANSION_FACTOR))
    # In plain words (later condition overrules previous ones):
    # allow MAX_EXPANSION_FACTOR times initial mail size,
    # but not more than MAX_EXPANSION_QUOTA,
    # but not less than MIN_EXPANSION_FACTOR times initial mail size,
    # but never less than MIN_EXPANSION_QUOTA
    $MIN_EXPANSION_QUOTA = 100*1024; # bytes (default undef, not enforced)
    $MAX_EXPANSION_QUOTA = 300*1024*1024; # bytes (default undef, not enforced)
    $MIN_EXPANSION_FACTOR = 5; # times original mail size (must be specified)
    $MAX_EXPANSION_FACTOR = 500; # times original mail size (must be specified)
    # Section VII - External programs, virus scanners
    # Specify a path string, which is a colon-separated string of directories
    # (no trailing slashes!) to be assigned to the environment variable PATH
    # and to serve for locating external programs below.
    # NOTE: if $daemon_chroot_dir is nonempty, the directories will be
    # relative to the chroot directory specified;
    $path = '/usr/local/sbin:/usr/local/bin:/usr/sbin:/sbin:/usr/bin:/bin';
    # Specify one string or a search list of strings (first match wins).
    # The string (or: each string in a list) may be an absolute path,
    # or just a program name, to be located via $path;
    # Empty string or undef (=default) disables the use of that external program.
    # Optionally command arguments may be specified - only the first substring
    # up to the whitespace is used for file searching.
    $file = 'file'; # file(1) utility; use 3.41 or later to avoid vulnerability
    $gzip = 'gzip';
    $bzip2 = 'bzip2';
    $lzop = 'lzop';
    $uncompress = ['uncompress', 'gzip -d', 'zcat'];
    $unfreeze = ['unfreeze', 'freeze -d', 'melt', 'fcat'];
    $arc = ['nomarch', 'arc'];
    $unarj = ['arj', 'unarj']; # both can extract, same options
    $unrar = ['rar', 'unrar']; # both can extract, same options
    $zoo = 'zoo';
    $lha = 'lha';
    $cpio = 'cpio';
    # SpamAssassin settings
    # $sa_local_tests_only is passed to Mail::SpamAssassin::new as a value
    # of the option local_tests_only. See Mail::SpamAssassin man page.
    # If set to 1, no tests that require internet access will be performed.
    $sa_local_tests_only = 1; # (default: false)
    #$sa_auto_whitelist = 1; # turn on AWL (default: false)
    $sa_mail_body_size_limit = 64*1024; # don't waste time on SA if mail is larger
    # (less than 1% of spam is > 64k)
    # default: undef, no limitations
    # default values, can be overridden by more specific lookups, e.g. SQL
    $sa_tag_level_deflt = -999; # add spam info headers if at, or above that level
    $sa_tag2_level_deflt = 3.0; # add 'spam detected' headers at that level
    $sa_kill_level_deflt = 22.0;
    #$sa_kill_level_deflt = $sa_tag2_level_deflt; # triggers spam evasive actions
    # at or above that level: bounce/reject/drop,
    # quarantine, and adding mail address extension
    # The $sa_tag_level_deflt, $sa_tag2_level_deflt and $sa_kill_level_deflt
    # may also be hashrefs to hash lookup tables, to make static per-recipient
    # settings possible without having to resort to SQL or LDAP lookups.
    # a quick reference:
    # tag_level controls adding the X-Spam-Status and X-Spam-Level headers,
    # tag2_level controls adding 'X-Spam-Flag: YES', and editing Subject,
    # kill_level controls 'evasive actions' (reject, quarantine, extensions);
    # it only makes sense to maintain the relationship:
    # tag_level <= tag2_level <= kill_level
    # string to prepend to Subject header field when message exceeds tag2 level
    $sa_spam_subject_tag = '*** JUNK MAIL ***'; # (defaults to undef, disables)
    # (only seen when spam is not to be rejected
    # and recipient is in local_domains*)
    $sa_spam_modifies_subj = 1; # may be a ref to a lookup table, default is true
    # Example: modify Subject for all local recipients except [email protected]
    #$sa_spam_modifies_subj = [qw( [email protected] . )];
    # @av_scanners is a list of n-tuples, where fields semantics is:
    # 1. av scanner plain name, to be used in log and reports;
    # 2. scanner program name; this string will be submitted to subroutine
    # find_external_programs(), which will try to find the full program
    # path name; if program is not found, this scanner is disabled.
    # Besides a simple string (full program path name or just the basename
    # to be looked for in PATH), this may be an array ref of alternative
    # program names or full paths - the first match in the list will be used;
    # As a special case for more complex scanners, this field may be
    # a subroutine reference, and the whole n-tuple is passed to it as args.
    # 3. command arguments to be given to the scanner program;
    # a substring {} will be replaced by the directory name to be scanned,
    # i.e. "$tempdir/parts"
    # 4. an array ref of av scanner exit status values, or a regexp (to be
    # matched against scanner output), indicating NO VIRUSES found;
    # 5. an array ref of av scanner exit status values, or a regexp (to be
    # matched against scanner output), indicating VIRUSES WERE FOUND;
    # Note: the virus match prevails over a 'not found' match, so it is safe
    # even if 4. matches for viruses too;
    # 6. a regexp (to be matched against scanner output), returning a list
    # of virus names found.
    # 7. and 8.: (optional) subroutines to be executed before and after scanner
    # (e.g. to set environment or current directory);
    # see examples for these at KasperskyLab AVP and Sophos sweep.
    # NOTES:
    # - NOT DEFINING @av_scanners (e.g. setting it to empty list, or deleting the
    # whole assignment) TURNS OFF LOADING AND COMPILING OF THE ANTIVIRUS CODE
    # (which can be handy if all you want to do is spam scanning);
    # - the order matters: although _all_ available entries from the list are
    # always tried regardless of their verdict, scanners are run in the order
    # specified: the report from the first one detecting a virus will be used
    # (providing virus names and scanner output); REARRANGE THE ORDER TO WILL;
    # - it doesn't hurt to keep an unused command line scanner entry in the list
    # if the program can not be found; the path search is only performed once
    # during the program startup;
    # CORROLARY: to disable a scanner that _does_ exist on your system,
    # comment out its entry or use undef or '' as its program name/path
    # (second parameter). An example where this is almost a must: disable
    # Sophos 'sweep' if you have its daemonized version Sophie or SAVI-Perl
    # (same for Trophie/vscan, and clamd/clamscan), or if another unrelated
    # program happens to have a name matching one of the entries ('sweep'
    # again comes to mind);
    # - it DOES HURT to keep unwanted entries which use INTERNAL SUBROUTINES
    # for interfacing (where the second parameter starts with \&).
    # Keeping such entry and not having a corresponding virus scanner daemon
    # causes an unnecessary connection attempt (which eventually times out,
    # but it wastes precious time). For this reason the daemonized entries
    # are commented in the distribution - just remove the '#' where needed.
    @av_scanners = (
    # ### http://www.vanja.com/tools/sophie/
    # ['Sophie',
    # \&ask_daemon, ["{}/\n", '/var/run/sophie'],
    # qr/(?x)^ 0+ ( : | [\000\r\n]* $)/, qr/(?x)^ 1 ( : | [\000\r\n]* $)/,
    # qr/(?x)^ [-+]? \d+ : (.*?) [\000\r\n]* $/ ],
    # ### http://www.csupomona.edu/~henson/www/projects/SAVI-Perl/
    # ['Sophos SAVI', \&sophos_savi ],
    # ### http://clamav.elektrapro.com/
    # ['Clam Antivirus-clamd',
    # \&ask_daemon, ["CONTSCAN {}\n", '/var/amavis/clamd'],
    # qr/\bOK$/, qr/\bFOUND$/,
    # qr/^.*?: (?!Infected Archive)(.*) FOUND$/ ],
    # # NOTE: run clamd under the same user as amavisd,
    # # match the socket name in clamav.conf to the socket name in this entry
    # ### http://www.openantivirus.org/
    # ['OpenAntiVirus ScannerDaemon (OAV)',
    # \&ask_daemon, ["SCAN {}\n", '127.0.0.1:8127'],
    # qr/^OK/, qr/^FOUND: /, qr/^FOUND: (.+)/ ],
    # ### http://www.vanja.com/tools/trophie/
    # ['Trophie',
    # \&ask_daemon, ["{}/\n", '/var/run/trophie'],
    # qr/(?x)^ 0+ ( : | [\000\r\n]* $)/, qr/(?x)^ 1 ( : | [\000\r\n]* $)/,
    # qr/(?x)^ [-+]? \d+ : (.*?) [\000\r\n]* $/ ],
    # ### http://www.f-prot.com/
    # ['FRISK F-Prot Daemon',
    # \&ask_daemon,
    # ["GET {}/*?-dumb%20-archive HTTP/1.0\r\n\r\n",
    # ['127.0.0.1:10200','127.0.0.1:10201','127.0.0.1:10202',
    # '127.0.0.1:10203','127.0.0.1:10204'] ],
    # qr/(?i)<summary[^>]*>clean<\/summary>/,
    # qr/(?i)<summary[^>]*>infected<\/summary>/,
    # qr/(?i)<name>(.+)<\/name>/ ],
    ['KasperskyLab AntiViral Toolkit Pro (AVP)', ['avp','kavscanner'],
    "-* -P -B -Y -O- {}", [0,3,8], [2,4], # any use for -A -K ?
    qr/infected: (.+)/,
    sub {chdir('/opt/AVP') or die "Can't chdir to AVP: $!"},
    sub {chdir($TEMPBASE) or die "Can't chdir back to $TEMPBASE $!"},
    ['KasperskyLab AVPDaemonClient',
    [ '/opt/AVP/kavdaemon', 'kavdaemon',
    '/opt/AVP/AvpDaemonClient', 'AvpDaemonClient',
    '/opt/AVP/AvpTeamDream', 'AvpTeamDream',
    '/opt/AVP/avpdc', 'avpdc' ],
    '{}', [0,8], [3,4,5,6], qr/infected: ([^\r\n]+)/ ],
    # change the startup-script in /etc/init.d/kavd to:
    # DPARMS="-I0 -Y -* /var/amavis"
    # adjusting /var/amavis above to match your $TEMPBASE.
    # NOTE: cd /opt/AVP/DaemonClients; configure; cd Sample; make
    # cp AvpDaemonClient /opt/AVP/
    ### http://www.hbedv.com/ or http://www.centralcommand.com/
    ['H+BEDV AntiVir or CentralCommand Vexira Antivirus',
    ['antivir','vexira'],
    '--allfiles -noboot -nombr -rs -s -z {}', [0], qr/ALERT:|VIRUS:/,
    qr/(?x)^\s* (?: ALERT: \s* (?: \[ | [^']* ' ) |
    (?i) VIRUS:\ .*?\ virus\ '?) ( [^\]\s']+ )/ ],
    # NOTE: remove the -z if you only have a demo version
    ### http://www.commandsoftware.com/
    ['Command AntiVirus for Linux', 'csav',
    '-all -archive -packed {}', [50], [51,52,53],
    qr/Infection: (.+)/ ],
    ### http://www.symantec.com/
    ['Symantec CarrierScan via Symantec CommandLineScanner',
    ['cscmdline','savsecls'],
    '-a scan -i 1 -v -s 127.0.0.1:7777 {}',
    qr/Files Infected: 0/, qr/^Infected: /,
    qr/Info:\s+(.+)/ ],
    ### http://drweb.imshop.de/
    ['DrWeb Antivirus for Linux/FreeBSD/Solaris', 'drweb',
    '-al -ar -fm -go -ha -ml -ot -sd -up {}',
    [0], [1], sub {('no-name')} ],
    ### http://www.f-secure.com/products/anti-virus/
    ['F-Secure Antivirus', 'fsav',
    '--dumb --archive {}', [0], [3,8],
    qr/(?:infection|Infected): (.+)/ ],
    ['CAI InoculateIT', 'inocucmd',
    '-sec -nex {}', [0], [100],
    qr/was infected by virus (.+)/ ],
    ['MkS_Vir for Linux (beta)', ['mks32','mks'],
    '-s {}/*', [0], [1,2],
    qr/--[ \t]*(.+)/ ],
    ['MkS_Vir daemon',
    'mksscan', '-s -q {}', [0], [1..7],
    qr/^... (\S+)/ ],
    ### http://www.nod32.com/
    ['ESET Software NOD32', 'nod32',
    '-all -subdir+ {}', [0], [1,2],
    qr/^.+? - (.+?)\s*(?:backdoor|joke|trojan|virus|worm)/ ],
    ### http://www.nod32.com/
    ['ESET Software NOD32 - Client/Server Version', 'nod32cli',
    '-a -r -d recurse --heur standard {}', [0], [10,11],
    qr/^\S+\s+infected:\s+(.+)/ ],
    ### http://www.norman.com/products_nvc.shtml
    ['Norman Virus Control v5 / Linux', 'nvccmd',
    '-c -l:0 -s -u {}', [0], [1],
    qr/(?i).* virus in .* -> \'(.+)\'/ ],
    ### http://www.pandasoftware.com/
    ['Panda Antivirus for Linux', ['pavcl','pavc'],
    '-aut -aex -heu -cmp -nor -nso -eng {}',
    qr/Number of files infected\.*: 0(?!\d)/,
    qr/Number of files infected\.*: 0*[1-9]/,
    qr/Found virus :\s*(\S+)/ ],
    # Check your RAV license terms before fiddling with the following two lines!
    # ['GeCAD RAV AntiVirus 8', 'ravav',
    # '--all --archive --mail {}', [1], [2,3,4,

    You are welcome. I'm glad you got it back up.
    (1) You say you did the symbolic link. I will assume this is set correctly; it's very important that it is.
    (2) I don't know what you mean by "Been feeding the [email protected] for several weeks now, 700 emails each day at least." After the initial training period, SpamAssassin doesn't learn from mail it has already processed correctly. At this point, you only need to teach SpamAssassin when it is wrong. [email protected] should only be getting spam that is being passed as clean. Likewise, [email protected] should only be getting legitimate mail that is being flagged as junk. You are redirecting mail to both [email protected] and [email protected] ... right? SpamAssassin needs both.
    (3) Next, as I said before, you need to implement those "Frontline spam defense for Mac OS X Server." Once you have that done and issue "postfix reload" you can look at your SMTP log in Server Admin and watch as Postfix blocks one piece of junk mail after another. It's kind of cool.
    (4) Add some SARE rules:
    Visit http://www.rulesemporium.com/rules.htm and download the following rules:
    70sareadult.cf
    70saregenlsubj0.cf
    70sareheader0.cf
    70sarehtml0.cf
    70sareobfu0.cf
    70sareoem.cf
    70sarespoof.cf
    70sarestocks.cf
    70sareunsub.cf
    72sare_redirectpost
    Visit http://www.rulesemporium.com/other-rules.htm and download the following rules:
    backhair.cf
    bogus-virus-warnings.cf
    chickenpox.cf
    weeds.cf
    Copy these rules to /etc/mail/spamassassin/
    Then stop and restart mail services.
    There are other things you can do, and you'll find differing opinions about such things. In general, I think implementing the "Frontline spam defense for Mac OS X Server" and adding the SARE rules will help a lot. Good luck!

  • NVIDIA driver not working on HP envy dv7

    Hi,
    i trying to install nvidia official driver to my HP envy dv7 laptop.
    Two wasted nights without success.
    I trying newest version from nvidia.com and from pacman.
    Result is same in both cases - black screen, high cpu temperatures, no video output.
    Pasted logs are from pacman version.
    Thank you for help !
    uname -a :
    $ uname -a
    Linux localhost 3.13.5-1-ARCH #1 SMP PREEMPT Sun Feb 23 00:25:24 CET 2014 x86_64 GNU/Linux
    lspci | grep VGA
    $ lspci | grep VGA
    00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
    01:00.0 VGA compatible controller: NVIDIA Corporation GF108M [GeForce GT 630M] (rev a1)
    modinfo nvidia
    $modinfo nvidia
    filename: /lib/modules/3.13.5-1-ARCH/extramodules/nvidia.ko.gz
    alias: char-major-195-*
    version: 331.38
    supported: external
    license: NVIDIA
    alias: pci:v000010DEd00000E00sv*sd*bc04sc80i00*
    alias: pci:v000010DEd00000AA3sv*sd*bc0Bsc40i00*
    alias: pci:v000010DEd*sv*sd*bc03sc02i00*
    alias: pci:v000010DEd*sv*sd*bc03sc00i00*
    depends: drm,i2c-core
    vermagic: 3.13.0-1-ARCH SMP preempt mod_unload modversions
    parm: NVreg_Mobile:int
    parm: NVreg_ResmanDebugLevel:int
    parm: NVreg_RmLogonRC:int
    parm: NVreg_ModifyDeviceFiles:int
    parm: NVreg_DeviceFileUID:int
    parm: NVreg_DeviceFileGID:int
    parm: NVreg_DeviceFileMode:int
    parm: NVreg_RemapLimit:int
    parm: NVreg_UpdateMemoryTypes:int
    parm: NVreg_InitializeSystemMemoryAllocations:int
    parm: NVreg_RMEdgeIntrCheck:int
    parm: NVreg_UsePageAttributeTable:int
    parm: NVreg_MapRegistersEarly:int
    parm: NVreg_RegisterForACPIEvents:int
    parm: NVreg_CheckPCIConfigSpace:int
    parm: NVreg_EnablePCIeGen3:int
    parm: NVreg_EnableMSI:int
    parm: NVreg_MemoryPoolSize:int
    parm: NVreg_RegistryDwords:charp
    parm: NVreg_RmMsg:charp
    parm: NVreg_AssignGpus:charp
    pacman -Qi nvidia
    $pacman -Qi nvidia
    Name : nvidia
    Version : 331.38-3
    Description : NVIDIA drivers for linux
    Architecture : x86_64
    URL : http://www.nvidia.com/
    Licenses : custom
    Groups : None
    Provides : None
    Depends On : linux>=3.13 linux<3.14 nvidia-libgl nvidia-utils=331.38
    Optional Deps : None
    Required By : None
    Optional For : bumblebee
    Conflicts With : nvidia-96xx nvidia-173xx
    Replaces : None
    Installed Size : 4642.00 KiB
    Packager : Thomas Bächler <[email protected]>
    Build Date : Sun 26 Jan 2014 10:22:40 AM UTC
    Install Date : Wed 26 Feb 2014 05:45:32 PM UTC
    Install Reason : Explicitly installed
    Install Script : Yes
    Validated By : Signature
    nvidia-xconfig --query-gpu-info
    $nvidia-xconfig --query-gpu-info
    Number of GPUs: 1
    GPU #0:
    Name : GeForce GT 630M
    UUID : GPU-172f9afb-954f-a30c-b9e1-016f89943947
    PCI BusID : PCI:1:0:0
    Number of Display Devices: 1
    Display Device 0 (CRT-0):
    No EDID information available.
    xorg.0.log
    [ 2028.379]
    X.Org X Server 1.15.0
    Release Date: 2013-12-27
    [ 2028.394] X Protocol Version 11, Revision 0
    [ 2028.399] Build Operating System: Linux 3.12.5-1-ARCH x86_64
    [ 2028.407] Current Operating System: Linux localhost 3.13.5-1-ARCH #1 SMP PREEMPT Sun Feb 23 00:25:24 CET 2014 x86_64
    [ 2028.407] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=64c5186f-288d-4708-959e-38cca5d1b5c0 rw quiet
    [ 2028.423] Build Date: 09 January 2014 08:47:24AM
    [ 2028.431]
    [ 2028.439] Current version of pixman: 0.32.4
    [ 2028.456] Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
    [ 2028.456] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    [ 2028.498] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Feb 26 18:29:34 2014
    [ 2028.510] (==) Using config file: "/etc/X11/xorg.conf"
    [ 2028.522] (==) Using config directory: "/etc/X11/xorg.conf.d"
    [ 2028.535] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
    [ 2028.548] (==) ServerLayout "Layout0"
    [ 2028.561] (**) |-->Screen "Screen0" (0)
    [ 2028.574] (**) | |-->Monitor "Monitor0"
    [ 2028.587] (**) | |-->Device "Device0"
    [ 2028.601] (**) |-->Input Device "Keyboard0"
    [ 2028.615] (**) |-->Input Device "Mouse0"
    [ 2028.629] (==) Automatically adding devices
    [ 2028.643] (==) Automatically enabling devices
    [ 2028.658] (==) Automatically adding GPU devices
    [ 2028.673] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
    [ 2028.688] Entry deleted from font path.
    [ 2028.704] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
    [ 2028.721] Entry deleted from font path.
    [ 2028.738] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
    [ 2028.756] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
    [ 2028.774] Entry deleted from font path.
    [ 2028.792] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
    [ 2028.869] (==) FontPath set to:
    /usr/share/fonts/misc/,
    /usr/share/fonts/TTF/,
    /usr/share/fonts/Type1/
    [ 2028.889] (==) ModulePath set to "/usr/lib/xorg/modules"
    [ 2028.910] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
    [ 2028.931] (WW) Disabling Keyboard0
    [ 2028.952] (WW) Disabling Mouse0
    [ 2028.974] (II) Loader magic: 0x804c80
    [ 2028.995] (II) Module ABI versions:
    [ 2029.017] X.Org ANSI C Emulation: 0.4
    [ 2029.039] X.Org Video Driver: 15.0
    [ 2029.062] X.Org XInput driver : 20.0
    [ 2029.084] X.Org Server Extension : 8.0
    [ 2029.107] (II) xfree86: Adding drm device (/dev/dri/card0)
    [ 2029.109] (--) PCI:*(0:0:2:0) 8086:0166:103c:181d rev 9, Mem @ 0xd4000000/4194304, 0xc0000000/268435456, I/O @ 0x00005000/64
    [ 2029.134] (--) PCI: (0:1:0:0) 10de:0de9:103c:181d rev 161, Mem @ 0xd2000000/16777216, 0xa0000000/268435456, 0xb0000000/33554432, I/O @ 0x00004000/128, BIOS @ 0x????????/524288
    [ 2029.186] (II) Open ACPI successful (/var/run/acpid.socket)
    [ 2029.213] Initializing built-in extension Generic Event Extension
    [ 2029.240] Initializing built-in extension SHAPE
    [ 2029.267] Initializing built-in extension MIT-SHM
    [ 2029.295] Initializing built-in extension XInputExtension
    [ 2029.322] Initializing built-in extension XTEST
    [ 2029.349] Initializing built-in extension BIG-REQUESTS
    [ 2029.377] Initializing built-in extension SYNC
    [ 2029.404] Initializing built-in extension XKEYBOARD
    [ 2029.432] Initializing built-in extension XC-MISC
    [ 2029.459] Initializing built-in extension SECURITY
    [ 2029.486] Initializing built-in extension XINERAMA
    [ 2029.512] Initializing built-in extension XFIXES
    [ 2029.538] Initializing built-in extension RENDER
    [ 2029.564] Initializing built-in extension RANDR
    [ 2029.589] Initializing built-in extension COMPOSITE
    [ 2029.615] Initializing built-in extension DAMAGE
    [ 2029.640] Initializing built-in extension MIT-SCREEN-SAVER
    [ 2029.665] Initializing built-in extension DOUBLE-BUFFER
    [ 2029.688] Initializing built-in extension RECORD
    [ 2029.711] Initializing built-in extension DPMS
    [ 2029.734] Initializing built-in extension Present
    [ 2029.756] Initializing built-in extension DRI3
    [ 2029.778] Initializing built-in extension X-Resource
    [ 2029.800] Initializing built-in extension XVideo
    [ 2029.821] Initializing built-in extension XVideo-MotionCompensation
    [ 2029.842] Initializing built-in extension XFree86-VidModeExtension
    [ 2029.863] Initializing built-in extension XFree86-DGA
    [ 2029.883] Initializing built-in extension XFree86-DRI
    [ 2029.903] Initializing built-in extension DRI2
    [ 2029.923] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
    [ 2029.923] (II) LoadModule: "glx"
    [ 2029.964] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    [ 2029.993] (II) Module glx: vendor="NVIDIA Corporation"
    [ 2029.993] compiled for 4.0.2, module version = 1.0.0
    [ 2030.034] Module class: X.Org Server Extension
    [ 2030.055] (II) NVIDIA GLX Module 331.38 Wed Jan 8 19:10:17 PST 2014
    [ 2030.076] Loading extension GLX
    [ 2030.077] (II) LoadModule: "nvidia"
    [ 2030.120] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
    [ 2030.142] (II) Module nvidia: vendor="NVIDIA Corporation"
    [ 2030.142] compiled for 4.0.2, module version = 1.0.0
    [ 2030.185] Module class: X.Org Video Driver
    [ 2030.207] (II) NVIDIA dlloader X Driver 331.38 Wed Jan 8 18:51:00 PST 2014
    [ 2030.229] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
    [ 2030.251] (II) NVIDIA X compatibility module for ABI 15.0 built from xorg-server-1.14.99.901
    [ 2030.273] (II) X log verbosity: 5
    [ 2030.315] (--) using VT number 1
    [ 2030.462] (II) Loading sub module "fb"
    [ 2030.462] (II) LoadModule: "fb"
    [ 2030.462] (II) Loading /usr/lib/xorg/modules/libfb.so
    [ 2030.462] (II) Module fb: vendor="X.Org Foundation"
    [ 2030.462] compiled for 1.15.0, module version = 1.0.0
    [ 2030.462] ABI class: X.Org ANSI C Emulation, version 0.4
    [ 2030.462] (WW) Unresolved symbol: fbGetGCPrivateKey
    [ 2030.462] (II) Loading sub module "wfb"
    [ 2030.462] (II) LoadModule: "wfb"
    [ 2030.462] (II) Loading /usr/lib/xorg/modules/libwfb.so
    [ 2030.462] (II) Module wfb: vendor="X.Org Foundation"
    [ 2030.462] compiled for 1.15.0, module version = 1.0.0
    [ 2030.462] ABI class: X.Org ANSI C Emulation, version 0.4
    [ 2030.462] (II) Loading sub module "ramdac"
    [ 2030.462] (II) LoadModule: "ramdac"
    [ 2030.462] (II) Module "ramdac" already built-in
    [ 2030.462] (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
    [ 2030.462] (==) NVIDIA(0): RGB weight 888
    [ 2030.462] (==) NVIDIA(0): Default visual is TrueColor
    [ 2030.463] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
    [ 2030.463] (==) NVIDIA(0): Using HW cursor
    [ 2030.463] (==) NVIDIA(0): Video key set to default value of 0x101fe
    [ 2030.463] (==) NVIDIA(0): Not mapping the primary surface by default.
    [ 2030.463] (**) NVIDIA(0): Option "ConnectedMonitor" "DFP-0"
    [ 2030.463] (**) NVIDIA(0): Enabling 2D acceleration
    [ 2030.463] (**) NVIDIA(0): ConnectedMonitor string: "DFP-0"
    [ 2030.588] (WW) NVIDIA(0): Unable to read EDID for display device CRT-0
    [ 2030.588] (II) NVIDIA(GPU-0): Found DRM driver nvidia-drm (20130102)
    [ 2030.589] (II) NVIDIA(0): NVIDIA GPU GeForce GT 630M (GF108) at PCI:1:0:0 (GPU-0)
    [ 2030.589] (II) NVIDIA(0): GPU UUID: GPU-172f9afb-954f-a30c-b9e1-016f89943947
    [ 2030.589] (--) NVIDIA(0): Memory: 2097152 kBytes
    [ 2030.589] (II) NVIDIA(0): Board ID: 0xce4e
    [ 2030.589] (II) NVIDIA(0): Chip SKU: 770
    [ 2030.589] (II) NVIDIA(0): Chip SKU Mod: 1
    [ 2030.589] (II) NVIDIA(0): Project: 1303
    [ 2030.589] (II) NVIDIA(0): Project SKU: 0000
    [ 2030.589] (II) NVIDIA(0): GPU RAM Type: DDR3
    [ 2030.589] (--) NVIDIA(0): VideoBIOS: 70.08.b9.00.0b
    [ 2030.589] (--) NVIDIA(0): Found 2 heads on board
    [ 2030.589] (II) NVIDIA(0): Supported display device(s): CRT-0
    [ 2030.589] (II) NVIDIA(0): Bus detected as PCI Express
    [ 2030.589] (II) NVIDIA(0): Detected PCI Express Link width: 16X
    [ 2030.589] (II) NVIDIA(0): SPS : 1
    [ 2030.589] (II) NVIDIA(0): User configuration of GPU PowerMizer is supported
    [ 2030.589] (II) NVIDIA(0):
    [ 2030.591] (--) NVIDIA(0): Valid display device(s) on GeForce GT 630M at PCI:1:0:0
    [ 2030.591] (--) NVIDIA(0): CRT-0 (boot, connected)
    [ 2030.591] (--) NVIDIA(0): CRT-0 Name Aliases:
    [ 2030.591] (--) NVIDIA(0): CRT
    [ 2030.591] (--) NVIDIA(0): CRT-0
    [ 2030.591] (--) NVIDIA(0): DPY-0
    [ 2030.591] (--) NVIDIA(0): VGA-0
    [ 2030.591] (--) NVIDIA(0): CRT-0: 400.0 MHz maximum pixel clock
    [ 2030.591] (--) NVIDIA(0):
    [ 2030.591] (--) NVIDIA(0): --- EDID for CRT-0 ---
    [ 2030.591] (--) NVIDIA(0):
    [ 2030.591] (--) NVIDIA(0): No EDID Available.
    [ 2030.591] (--) NVIDIA(0):
    [ 2030.591] (--) NVIDIA(0): --- End of EDID for CRT-0 ---
    [ 2030.591] (--) NVIDIA(0):
    [ 2030.591] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
    [ 2030.591] (**) NVIDIA(0): device CRT-0 (Using EDID frequencies has been enabled on
    [ 2030.591] (**) NVIDIA(0): all display devices.)
    [ 2030.591] (II) NVIDIA(0): Frequency information for CRT-0:
    [ 2030.591] (II) NVIDIA(0): HorizSync : 28.000-55.000 kHz
    [ 2030.591] (II) NVIDIA(0): VertRefresh : 43.000-72.000 Hz
    [ 2030.591] (II) NVIDIA(0): (HorizSync from Conservative Defaults)
    [ 2030.591] (II) NVIDIA(0): (VertRefresh from Conservative Defaults)
    [ 2030.593] (II) NVIDIA(GPU-0):
    [ 2030.593] (II) NVIDIA(GPU-0): --- Modes in ModePool for CRT-0 ---
    [ 2030.593] (II) NVIDIA(GPU-0): "nvidia-auto-select" : 1024 x 768 @ 60.0 Hz (from: X Server, VESA)
    [ 2030.593] (II) NVIDIA(GPU-0): "1024x768" : 1024 x 768 @ 60.0 Hz (from: X Server, VESA)
    [ 2030.593] (II) NVIDIA(GPU-0): "1024x768_60" : 1024 x 768 @ 60.0 Hz (from: X Server, VESA)
    [ 2030.593] (II) NVIDIA(GPU-0): "800x600" : 800 x 600 @ 72.2 Hz (from: X Server, VESA)
    [ 2030.593] (II) NVIDIA(GPU-0): "800x600_72" : 800 x 600 @ 72.2 Hz (from: X Server, VESA)
    [ 2030.593] (II) NVIDIA(GPU-0): "800x600_60" : 800 x 600 @ 60.3 Hz (from: X Server, VESA)
    [ 2030.593] (II) NVIDIA(GPU-0): "800x600_56" : 800 x 600 @ 56.2 Hz (from: X Server, VESA)
    [ 2030.593] (II) NVIDIA(GPU-0): "640x480" : 640 x 480 @ 59.9 Hz (from: X Server, VESA)
    [ 2030.593] (II) NVIDIA(GPU-0): "640x480_60" : 640 x 480 @ 59.9 Hz (from: X Server, VESA)
    [ 2030.593] (II) NVIDIA(GPU-0): "512x384" : 512 x 384 @ 60.0 Hz DoubleScan (from: X Server)
    [ 2030.593] (II) NVIDIA(GPU-0): "512x384d60" : 512 x 384 @ 60.0 Hz DoubleScan (from: X Server)
    [ 2030.593] (II) NVIDIA(GPU-0): "400x300" : 400 x 300 @ 72.2 Hz DoubleScan (from: X Server)
    [ 2030.593] (II) NVIDIA(GPU-0): "400x300d72" : 400 x 300 @ 72.2 Hz DoubleScan (from: X Server)
    [ 2030.593] (II) NVIDIA(GPU-0): "320x240" : 320 x 240 @ 60.1 Hz DoubleScan (from: X Server)
    [ 2030.593] (II) NVIDIA(GPU-0): "320x240d60" : 320 x 240 @ 60.1 Hz DoubleScan (from: X Server)
    [ 2030.593] (II) NVIDIA(GPU-0): --- End of ModePool for CRT-0: ---
    [ 2030.593] (II) NVIDIA(GPU-0):
    [ 2030.593] (II) NVIDIA(0): Display device(s) assigned to X screen 0:
    [ 2030.593] (II) NVIDIA(0): CRT-0
    [ 2030.593] (==) NVIDIA(0):
    [ 2030.593] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
    [ 2030.593] (==) NVIDIA(0): will be used as the requested mode.
    [ 2030.593] (==) NVIDIA(0):
    [ 2030.593] (II) NVIDIA(0): Requested modes:
    [ 2030.593] (II) NVIDIA(0): "CRT-0:nvidia-auto-select"
    [ 2030.593] (II) NVIDIA(0): Validated MetaModes:
    [ 2030.593] (II) NVIDIA(0): MetaMode "CRT-0:nvidia-auto-select":
    [ 2030.593] (II) NVIDIA(0): Size: 1024 x 768
    [ 2030.593] (II) NVIDIA(0): CRT-0: "nvidia-auto-select"
    [ 2030.593] (II) NVIDIA(0): Size : 1024 x 768
    [ 2030.593] (II) NVIDIA(0): Offset : +0 +0
    [ 2030.593] (II) NVIDIA(0): Panning
    [ 2030.593] (II) NVIDIA(0): Domain : 1024 x 768
    [ 2030.593] (II) NVIDIA(0): Tracking Area: 1024 x 768 +0 +0
    [ 2030.593] (II) NVIDIA(0): Border : 0,0,0,0
    [ 2030.593] (II) NVIDIA(0): Virtual screen size determined to be 1024 x 768
    [ 2030.594] (II) NVIDIA(0): Adding implicit MetaMode: "VGA-0: 800x600"
    [ 2030.594] (II) NVIDIA(0): Adding implicit MetaMode: "VGA-0: 800x600_60"
    [ 2030.594] (II) NVIDIA(0): Adding implicit MetaMode: "VGA-0: 800x600_56"
    [ 2030.594] (II) NVIDIA(0): Adding implicit MetaMode: "VGA-0: 640x480"
    [ 2030.594] (II) NVIDIA(0): Adding implicit MetaMode: "VGA-0: 512x384"
    [ 2030.594] (II) NVIDIA(0): Adding implicit MetaMode: "VGA-0: 400x300"
    [ 2030.594] (II) NVIDIA(0): Adding implicit MetaMode: "VGA-0: 320x240"
    [ 2030.594] (II) NVIDIA(0): Adding implicit MetaMode: "VGA-0: nvidia-auto-select { ViewPortIn = 1024 x 576, ViewPortOut = 1024 x 576 + 0 + 96 }"
    [ 2030.596] (WW) NVIDIA(0): Unable to get display device CRT-0's EDID; cannot compute DPI
    [ 2030.596] (WW) NVIDIA(0): from CRT-0's EDID.
    [ 2030.596] (==) NVIDIA(0): DPI set to (75, 75); computed from built-in default
    [ 2030.596] (--) Depth 24 pixmap format is 32 bpp
    [ 2030.597] (II) NVIDIA: Using 3072.00 MB of virtual memory for indirect memory
    [ 2030.597] (II) NVIDIA: access.
    [ 2030.599] (II) NVIDIA(0): kernel module enabled successfully
    [ 2030.599] (II) NVIDIA(0): GPU initialized
    [ 2030.599] (II) NVIDIA(0): ACPI: AC state file path: /sys/class/power_supply/ADP1/online
    [ 2030.599] (II) NVIDIA(0): ACPI: the system is running on battery power
    [ 2030.599] (II) NVIDIA(0): ACPI: dock file path: /sys/devices/platform//dock.0/docked
    [ 2030.599] (II) NVIDIA(0): ACPI: the system is undocked
    [ 2030.599] (II) NVIDIA(0): Registered for mobile display change hotkey events.
    [ 2030.602] (II) NVIDIA(0): Setting mode "CRT-0:nvidia-auto-select"
    [ 2030.619] (II) NVIDIA(0): First mode initialized
    [ 2030.624] (==) NVIDIA(0): Using 8388608 bytes for software rendering cache
    [ 2030.629] (II) NVIDIA(0): Using built-in logo image.
    [ 2030.629] (II) NVIDIA(0): Logo is 744x537 with depth 24.
    [ 2030.641] Loading extension NV-GLX
    [ 2030.689] (II) NVIDIA(0): Initialized OpenGL Acceleration
    [ 2030.689] (II) NVIDIA(0): Visuals set up
    [ 2030.689] (II) NVIDIA(0): Pixmap depths set up
    [ 2030.690] (II) NVIDIA(0): GLX visuals set up
    [ 2030.690] (II) NVIDIA(0): Framebuffer set up
    [ 2030.690] (==) NVIDIA(0): Disabling shared memory pixmaps
    [ 2030.690] (II) NVIDIA(0): Initialized X Rendering Acceleration
    [ 2030.690] (==) NVIDIA(0): Backing store enabled
    [ 2030.690] (==) NVIDIA(0): Silken mouse enabled
    [ 2030.690] (II) NVIDIA(0): Default colormap initialized.
    [ 2030.690] (II) NVIDIA(0): Palette loaded
    [ 2030.690] (**) NVIDIA(0): DPMS enabled
    [ 2030.690] Loading extension NV-CONTROL
    [ 2030.690] Loading extension XINERAMA
    [ 2030.690] (II) NVIDIA(0): Loading NVIDIA Xinerama information
    [ 2030.690] (II) Loading sub module "dri2"
    [ 2030.690] (II) LoadModule: "dri2"
    [ 2030.690] (II) Module "dri2" already built-in
    [ 2030.690] (II) NVIDIA(0): [DRI2] Setup complete
    [ 2030.690] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
    [ 2030.690] (II) NVIDIA(0): Screen initialization complete
    [ 2030.690] (--) RandR disabled
    [ 2030.695] (II) Initializing extension GLX
    [ 2030.726] (II) XKB: Reusing cached keymap
    [ 2030.728] (II) config/udev: Adding input device Power Button (/dev/input/event2)
    [ 2030.728] (**) Power Button: Applying InputClass "evdev keyboard catchall"
    [ 2030.728] (II) LoadModule: "evdev"
    [ 2030.728] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 2030.728] (II) Module evdev: vendor="X.Org Foundation"
    [ 2030.728] compiled for 1.15.0, module version = 2.8.2
    [ 2030.728] Module class: X.Org XInput Driver
    [ 2030.728] ABI class: X.Org XInput driver, version 20.0
    [ 2030.728] (II) Using input driver 'evdev' for 'Power Button'
    [ 2030.728] Option "XkbRules" "evdev"
    [ 2030.728] Option "XkbModel" "pc104"
    [ 2030.728] Option "XkbLayout" "us"
    [ 2030.728] Option "_source" "server/udev"
    [ 2030.728] Option "name" "Power Button"
    [ 2030.728] Option "path" "/dev/input/event2"
    [ 2030.728] Option "device" "/dev/input/event2"
    [ 2030.728] Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event2"
    [ 2030.728] Option "driver" "evdev"
    [ 2030.728] (**) Power Button: always reports core events
    [ 2030.728] (**) evdev: Power Button: Device: "/dev/input/event2"
    [ 2030.729] (--) evdev: Power Button: Vendor 0 Product 0x1
    [ 2030.729] (--) evdev: Power Button: Found keys
    [ 2030.729] (II) evdev: Power Button: Configuring as keyboard
    [ 2030.729] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event2"
    [ 2030.729] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
    [ 2030.729] (**) Option "xkb_rules" "evdev"
    [ 2030.729] (**) Option "xkb_model" "pc104"
    [ 2030.729] (**) Option "xkb_layout" "us"
    [ 2030.748] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
    [ 2030.748] (II) No input driver specified, ignoring this device.
    [ 2030.748] (II) This device may have been added with another device file.
    [ 2030.748] (II) config/udev: Adding drm device (/dev/dri/card0)
    [ 2030.748] (II) config/udev: Adding input device HP Truevision HD (/dev/input/event7)
    [ 2030.748] (**) HP Truevision HD: Applying InputClass "evdev keyboard catchall"
    [ 2030.748] (II) Using input driver 'evdev' for 'HP Truevision HD'
    [ 2030.748] Option "XkbRules" "evdev"
    [ 2030.748] Option "XkbModel" "pc104"
    [ 2030.748] Option "XkbLayout" "us"
    [ 2030.748] Option "_source" "server/udev"
    [ 2030.748] Option "name" "HP Truevision HD"
    [ 2030.748] Option "path" "/dev/input/event7"
    [ 2030.748] Option "device" "/dev/input/event7"
    [ 2030.748] Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input10/event7"
    [ 2030.748] Option "driver" "evdev"
    [ 2030.748] (**) HP Truevision HD: always reports core events
    [ 2030.748] (**) evdev: HP Truevision HD: Device: "/dev/input/event7"
    [ 2030.748] (--) evdev: HP Truevision HD: Vendor 0x5c8 Product 0x33a
    [ 2030.748] (--) evdev: HP Truevision HD: Found keys
    [ 2030.748] (II) evdev: HP Truevision HD: Configuring as keyboard
    [ 2030.748] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input10/event7"
    [ 2030.748] (II) XINPUT: Adding extended input device "HP Truevision HD" (type: KEYBOARD, id 7)
    [ 2030.748] (**) Option "xkb_rules" "evdev"
    [ 2030.748] (**) Option "xkb_model" "pc104"
    [ 2030.748] (**) Option "xkb_layout" "us"
    [ 2030.748] (II) XKB: Reusing cached keymap
    [ 2030.749] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event3)
    [ 2030.749] (II) No input driver specified, ignoring this device.
    [ 2030.749] (II) This device may have been added with another device file.
    [ 2030.749] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event6)
    [ 2030.749] (II) No input driver specified, ignoring this device.
    [ 2030.749] (II) This device may have been added with another device file.
    [ 2030.749] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event5)
    [ 2030.749] (II) No input driver specified, ignoring this device.
    [ 2030.749] (II) This device may have been added with another device file.
    [ 2030.749] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event4)
    [ 2030.749] (II) No input driver specified, ignoring this device.
    [ 2030.749] (II) This device may have been added with another device file.
    [ 2030.749] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
    [ 2030.750] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
    [ 2030.750] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
    [ 2030.750] Option "XkbRules" "evdev"
    [ 2030.750] Option "XkbModel" "pc104"
    [ 2030.750] Option "XkbLayout" "us"
    [ 2030.750] Option "_source" "server/udev"
    [ 2030.750] Option "name" "AT Translated Set 2 keyboard"
    [ 2030.750] Option "path" "/dev/input/event0"
    [ 2030.750] Option "device" "/dev/input/event0"
    [ 2030.750] Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
    [ 2030.750] Option "driver" "evdev"
    [ 2030.750] (**) AT Translated Set 2 keyboard: always reports core events
    [ 2030.750] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
    [ 2030.750] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
    [ 2030.750] (--) evdev: AT Translated Set 2 keyboard: Found keys
    [ 2030.750] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
    [ 2030.750] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
    [ 2030.750] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 8)
    [ 2030.750] (**) Option "xkb_rules" "evdev"
    [ 2030.750] (**) Option "xkb_model" "pc104"
    [ 2030.750] (**) Option "xkb_layout" "us"
    [ 2030.750] (II) XKB: Reusing cached keymap
    [ 2030.750] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event10)
    [ 2030.750] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
    [ 2030.750] (II) Using input driver 'evdev' for 'SynPS/2 Synaptics TouchPad'
    [ 2030.750] Option "XkbRules" "evdev"
    [ 2030.750] Option "XkbModel" "pc104"
    [ 2030.750] Option "XkbLayout" "us"
    [ 2030.750] Option "_source" "server/udev"
    [ 2030.750] Option "name" "SynPS/2 Synaptics TouchPad"
    [ 2030.750] Option "path" "/dev/input/event10"
    [ 2030.750] Option "device" "/dev/input/event10"
    [ 2030.750] Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input5/event10"
    [ 2030.750] Option "driver" "evdev"
    [ 2030.750] (**) SynPS/2 Synaptics TouchPad: always reports core events
    [ 2030.750] (**) evdev: SynPS/2 Synaptics TouchPad: Device: "/dev/input/event10"
    [ 2030.750] (II) evdev: SynPS/2 Synaptics TouchPad: Using mtdev for this device
    [ 2030.750] (--) evdev: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
    [ 2030.750] (--) evdev: SynPS/2 Synaptics TouchPad: Found 3 mouse buttons
    [ 2030.750] (--) evdev: SynPS/2 Synaptics TouchPad: Found absolute axes
    [ 2030.750] (--) evdev: SynPS/2 Synaptics TouchPad: Found absolute multitouch axes
    [ 2030.750] (--) evdev: SynPS/2 Synaptics TouchPad: Found x and y absolute axes
    [ 2030.751] (--) evdev: SynPS/2 Synaptics TouchPad: Found absolute touchpad.
    [ 2030.751] (II) evdev: SynPS/2 Synaptics TouchPad: Configuring as touchpad
    [ 2030.751] (**) evdev: SynPS/2 Synaptics TouchPad: YAxisMapping: buttons 4 and 5
    [ 2030.751] (**) evdev: SynPS/2 Synaptics TouchPad: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    [ 2030.751] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input5/event10"
    [ 2030.751] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 9)
    [ 2030.751] (II) evdev: SynPS/2 Synaptics TouchPad: initialized for absolute axes.
    [ 2030.751] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
    [ 2030.751] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0
    [ 2030.751] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
    [ 2030.751] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
    [ 2030.751] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0)
    [ 2030.751] (II) No input driver specified, ignoring this device.
    [ 2030.751] (II) This device may have been added with another device file.
    [ 2030.751] (II) config/udev: Adding input device ST LIS3LV02DL Accelerometer (/dev/input/event8)
    [ 2030.751] (II) No input driver specified, ignoring this device.
    [ 2030.751] (II) This device may have been added with another device file.
    [ 2030.751] (II) config/udev: Adding input device ST LIS3LV02DL Accelerometer (/dev/input/js0)
    [ 2030.751] (II) No input driver specified, ignoring this device.
    [ 2030.751] (II) This device may have been added with another device file.
    [ 2030.752] (II) config/udev: Adding input device HP WMI hotkeys (/dev/input/event9)
    [ 2030.752] (**) HP WMI hotkeys: Applying InputClass "evdev keyboard catchall"
    [ 2030.752] (II) Using input driver 'evdev' for 'HP WMI hotkeys'
    [ 2030.752] Option "XkbRules" "evdev"
    [ 2030.752] Option "XkbModel" "pc104"
    [ 2030.752] Option "XkbLayout" "us"
    [ 2030.752] Option "_source" "server/udev"
    [ 2030.752] Option "name" "HP WMI hotkeys"
    [ 2030.752] Option "path" "/dev/input/event9"
    [ 2030.752] Option "device" "/dev/input/event9"
    [ 2030.752] Option "config_info" "udev:/sys/devices/virtual/input/input9/event9"
    [ 2030.752] Option "driver" "evdev"
    [ 2030.752] (**) HP WMI hotkeys: always reports core events
    [ 2030.752] (**) evdev: HP WMI hotkeys: Device: "/dev/input/event9"
    [ 2030.752] (--) evdev: HP WMI hotkeys: Vendor 0 Product 0
    [ 2030.752] (--) evdev: HP WMI hotkeys: Found keys
    [ 2030.752] (II) evdev: HP WMI hotkeys: Configuring as keyboard
    [ 2030.752] (**) Option "config_info" "udev:/sys/devices/virtual/input/input9/event9"
    [ 2030.752] (II) XINPUT: Adding extended input device "HP WMI hotkeys" (type: KEYBOARD, id 10)
    [ 2030.752] (**) Option "xkb_rules" "evdev"
    [ 2030.752] (**) Option "xkb_model" "pc104"
    [ 2030.752] (**) Option "xkb_layout" "us"
    [ 2030.752] (II) XKB: Reusing cached keymap
    [ 2031.256] (WW) NVIDIA(GPU-0): Unable to read EDID for display device CRT-0
    [ 2031.256] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
    [ 2031.256] (**) NVIDIA(0): device CRT-0 (Using EDID frequencies has been enabled on
    [ 2031.256] (**) NVIDIA(0): all display devices.)
    [ 2031.256] (II) NVIDIA(0): Frequency information for CRT-0:
    [ 2031.256] (II) NVIDIA(0): HorizSync : 28.000-55.000 kHz
    [ 2031.256] (II) NVIDIA(0): VertRefresh : 43.000-72.000 Hz
    [ 2031.256] (II) NVIDIA(0): (HorizSync from Conservative Defaults)
    [ 2031.256] (II) NVIDIA(0): (VertRefresh from Conservative Defaults)
    [ 2031.257] (II) NVIDIA(GPU-0):
    [ 2031.257] (II) NVIDIA(GPU-0): --- Modes in ModePool for CRT-0 ---
    [ 2031.257] (II) NVIDIA(GPU-0): "nvidia-auto-select" : 1024 x 768 @ 60.0 Hz (from: X Server, VESA)
    [ 2031.257] (II) NVIDIA(GPU-0): "1024x768" : 1024 x 768 @ 60.0 Hz (from: X Server, VESA)
    [ 2031.257] (II) NVIDIA(GPU-0): "1024x768_60" : 1024 x 768 @ 60.0 Hz (from: X Server, VESA)
    [ 2031.257] (II) NVIDIA(GPU-0): "800x600" : 800 x 600 @ 72.2 Hz (from: X Server, VESA)
    [ 2031.257] (II) NVIDIA(GPU-0): "800x600_72" : 800 x 600 @ 72.2 Hz (from: X Server, VESA)
    [ 2031.258] (II) NVIDIA(GPU-0): "800x600_60" : 800 x 600 @ 60.3 Hz (from: X Server, VESA)
    [ 2031.258] (II) NVIDIA(GPU-0): "800x600_56" : 800 x 600 @ 56.2 Hz (from: X Server, VESA)
    [ 2031.258] (II) NVIDIA(GPU-0): "640x480" : 640 x 480 @ 59.9 Hz (from: X Server, VESA)
    [ 2031.258] (II) NVIDIA(GPU-0): "640x480_60" : 640 x 480 @ 59.9 Hz (from: X Server, VESA)
    [ 2031.258] (II) NVIDIA(GPU-0): "512x384" : 512 x 384 @ 60.0 Hz DoubleScan (from: X Server)
    [ 2031.258] (II) NVIDIA(GPU-0): "512x384d60" : 512 x 384 @ 60.0 Hz DoubleScan (from: X Server)
    [ 2031.258] (II) NVIDIA(GPU-0): "400x300" : 400 x 300 @ 72.2 Hz DoubleScan (from: X Server)
    [ 2031.258] (II) NVIDIA(GPU-0): "400x300d72" : 400 x 300 @ 72.2 Hz DoubleScan (from: X Server)
    [ 2031.258] (II) NVIDIA(GPU-0): "320x240" : 320 x 240 @ 60.1 Hz DoubleScan (from: X Server)
    [ 2031.258] (II) NVIDIA(GPU-0): "320x240d60" : 320 x 240 @ 60.1 Hz DoubleScan (from: X Server)
    [ 2031.258] (II) NVIDIA(GPU-0): --- End of ModePool for CRT-0: ---
    [ 2031.258] (II) NVIDIA(GPU-0):
    [ 2031.506] (WW) NVIDIA(GPU-0): Unable to read EDID for display device CRT-0
    [ 2031.506] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
    [ 2031.506] (**) NVIDIA(0): device CRT-0 (Using EDID frequencies has been enabled on
    [ 2031.506] (**) NVIDIA(0): all display devices.)
    [ 2031.506] (II) NVIDIA(0): Frequency information for CRT-0:
    [ 2031.506] (II) NVIDIA(0): HorizSync : 28.000-55.000 kHz
    [ 2031.506] (II) NVIDIA(0): VertRefresh : 43.000-72.000 Hz
    [ 2031.506] (II) NVIDIA(0): (HorizSync from Conservative Defaults)
    [ 2031.506] (II) NVIDIA(0): (VertRefresh from Conservative Defaults)
    [ 2031.509] (II) NVIDIA(GPU-0):
    [ 2031.509] (II) NVIDIA(GPU-0): --- Modes in ModePool for CRT-0 ---
    [ 2031.509] (II) NVIDIA(GPU-0): "nvidia-auto-select" : 1024 x 768 @ 60.0 Hz (from: X Server, VESA)
    [ 2031.509] (II) NVIDIA(GPU-0): "1024x768" : 1024 x 768 @ 60.0 Hz (from: X Server, VESA)
    [ 2031.509] (II) NVIDIA(GPU-0): "1024x768_60" : 1024 x 768 @ 60.0 Hz (from: X Server, VESA)
    [ 2031.509] (II) NVIDIA(GPU-0): "800x600" : 800 x 600 @ 72.2 Hz (from: X Server, VESA)
    [ 2031.509] (II) NVIDIA(GPU-0): "800x600_72" : 800 x 600 @ 72.2 Hz (from: X Server, VESA)
    [ 2031.509] (II) NVIDIA(GPU-0): "800x600_60" : 800 x 600 @ 60.3 Hz (from: X Server, VESA)
    [ 2031.509] (II) NVIDIA(GPU-0): "800x600_56" : 800 x 600 @ 56.2 Hz (from: X Server, VESA)
    [ 2031.509] (II) NVIDIA(GPU-0): "640x480" : 640 x 480 @ 59.9 Hz (from: X Server, VESA)
    [ 2031.509] (II) NVIDIA(GPU-0): "640x480_60" : 640 x 480 @ 59.9 Hz (from: X Server, VESA)
    [ 2031.509] (II) NVIDIA(GPU-0): "512x384" : 512 x 384 @ 60.0 Hz DoubleScan (from: X Server)
    [ 2031.509] (II) NVIDIA(GPU-0): "512x384d60" : 512 x 384 @ 60.0 Hz DoubleScan (from: X Server)
    [ 2031.509] (II) NVIDIA(GPU-0): "400x300" : 400 x 300 @ 72.2 Hz DoubleScan (from: X Server)
    [ 2031.509] (II) NVIDIA(GPU-0): "400x300d72" : 400 x 300 @ 72.2 Hz DoubleScan (from: X Server)
    [ 2031.509] (II) NVIDIA(GPU-0): "320x240" : 320 x 240 @ 60.1 Hz DoubleScan (from: X Server)
    [ 2031.509] (II) NVIDIA(GPU-0): "320x240d60" : 320 x 240 @ 60.1 Hz DoubleScan (from: X Server)
    [ 2031.509] (II) NVIDIA(GPU-0): --- End of ModePool for CRT-0: ---
    [ 2031.509] (II) NVIDIA(GPU-0):
    [ 2046.582] (II) evdev: HP WMI hotkeys: Close
    [ 2046.582] (II) UnloadModule: "evdev"
    [ 2046.623] (II) evdev: SynPS/2 Synaptics TouchPad: Close
    [ 2046.623] (II) UnloadModule: "evdev"
    [ 2046.663] (II) evdev: AT Translated Set 2 keyboard: Close
    [ 2046.663] (II) UnloadModule: "evdev"
    [ 2046.702] (II) evdev: HP Truevision HD: Close
    [ 2046.702] (II) UnloadModule: "evdev"
    [ 2046.741] (II) evdev: Power Button: Close
    [ 2046.741] (II) UnloadModule: "evdev"
    [ 2046.794] (II) NVIDIA(GPU-0): Deleting GPU-0
    [ 2046.795] (EE) Server terminated successfully (0). Closing log file.
    xorg.conf
    # nvidia-xconfig: X configuration file generated by nvidia-xconfig
    # nvidia-xconfig: version 331.38 (buildmeister@swio-display-x64-rhel04-15) Wed Jan 8 19:53:14 PST 2014
    Section "Module"
    Load "glx"
    EndSection
    Section "ServerLayout"
    Identifier "Layout0"
    Screen 0 "Screen0" 0 0
    InputDevice "Keyboard0" "CoreKeyboard"
    InputDevice "Mouse0" "CorePointer"
    EndSection
    Section "Files"
    EndSection
    Section "InputDevice"
    # generated from default
    Identifier "Mouse0"
    Driver "mouse"
    Option "Protocol" "auto"
    Option "Device" "/dev/psaux"
    Option "Emulate3Buttons" "no"
    Option "ZAxisMapping" "4 5"
    EndSection
    Section "InputDevice"
    # generated from default
    Identifier "Keyboard0"
    Driver "kbd"
    EndSection
    Section "Monitor"
    Identifier "Monitor0"
    # VendorName "Unknown"
    # ModelName "Unknown"
    # HorizSync 28.0 - 33.0
    # VertRefresh 43.0 - 72.0
    Option "DPMS"
    EndSection
    Section "Device"
    Identifier "Device0"
    Driver "nvidia"
    VendorName "NVIDIA Corporation"
    BusID "PCI:1:0:0"
    # Option "UseEDID" "true"
    Option "ConnectedMonitor" "DFP-0"
    # Option "CustomEDID" "CRT-0:/etc/X11/1280x1024.bin"
    EndSection
    Section "Screen"
    Identifier "Screen0"
    Device "Device0"
    Monitor "Monitor0"
    DefaultDepth 24
    SubSection "Display"
    Depth 24
    EndSubSection
    EndSection

    dmesg :
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.13.5-1-ARCH (nobody@var-lib-archbuild-extra-x86_64-thomas) (gcc version 4.8.2 20140206 (prerelease) (GCC) ) #1 SMP PREEMPT Sun Feb 23 00:25:24 CET 2014
    [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=64c5186f-288d-4708-959e-38cca5d1b5c0 rw quiet
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x00000000000917ff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000000091800-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000040003fff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000040004000-0x0000000040004fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000040005000-0x000000009a3befff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000009a3bf000-0x000000009aebefff] reserved
    [ 0.000000] BIOS-e820: [mem 0x000000009aebf000-0x000000009afbefff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x000000009afbf000-0x000000009affefff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x000000009afff000-0x000000009affffff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000009b000000-0x000000009f9fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb03fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ffb80000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000025f5fffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] SMBIOS 2.7 present.
    [ 0.000000] DMI: Hewlett-Packard HP ENVY dv7 Notebook PC/181D, BIOS F.12 09/03/2012
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x25f600 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-E7FFF write-protect
    [ 0.000000] E8000-EFFFF write-combining
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask F80000000 write-back
    [ 0.000000] 1 base 080000000 mask FE0000000 write-back
    [ 0.000000] 2 base 09B000000 mask FFF000000 uncachable
    [ 0.000000] 3 base 09C000000 mask FFC000000 uncachable
    [ 0.000000] 4 base 0FF800000 mask FFF800000 write-protect
    [ 0.000000] 5 base 100000000 mask F00000000 write-back
    [ 0.000000] 6 base 200000000 mask F80000000 write-back
    [ 0.000000] 7 base 25F600000 mask FFFE00000 uncachable
    [ 0.000000] 8 base 25F800000 mask FFF800000 uncachable
    [ 0.000000] 9 base 260000000 mask FE0000000 uncachable
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: last_pfn = 0x9b000 max_arch_pfn = 0x400000000
    [ 0.000000] found SMP MP-table at [mem 0x000fe1b0-0x000fe1bf] mapped at [ffff8800000fe1b0]
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff88000008b000] 8b000 size 24576
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b3f000, 0x01b3ffff] PGTABLE
    [ 0.000000] BRK [0x01b40000, 0x01b40fff] PGTABLE
    [ 0.000000] BRK [0x01b41000, 0x01b41fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x25f400000-0x25f5fffff]
    [ 0.000000] [mem 0x25f400000-0x25f5fffff] page 2M
    [ 0.000000] BRK [0x01b42000, 0x01b42fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x25c000000-0x25f3fffff]
    [ 0.000000] [mem 0x25c000000-0x25f3fffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x200000000-0x25bffffff]
    [ 0.000000] [mem 0x200000000-0x25bffffff] page 2M
    [ 0.000000] BRK [0x01b43000, 0x01b43fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x1fffffff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0x1fffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x20200000-0x40003fff]
    [ 0.000000] [mem 0x20200000-0x3fffffff] page 2M
    [ 0.000000] [mem 0x40000000-0x40003fff] page 4k
    [ 0.000000] BRK [0x01b44000, 0x01b44fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x40005000-0x9a3befff]
    [ 0.000000] [mem 0x40005000-0x401fffff] page 4k
    [ 0.000000] [mem 0x40200000-0x9a1fffff] page 2M
    [ 0.000000] [mem 0x9a200000-0x9a3befff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x9afff000-0x9affffff]
    [ 0.000000] [mem 0x9afff000-0x9affffff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x1ffffffff]
    [ 0.000000] [mem 0x100000000-0x1ffffffff] page 2M
    [ 0.000000] RAMDISK: [mem 0x379b0000-0x37ccffff]
    [ 0.000000] ACPI: RSDP 00000000000fe020 000024 (v02 HPQOEM)
    [ 0.000000] ACPI: XSDT 000000009affe210 0000A4 (v01 HPQOEM SLIC-MPC 00000001 HP 01000013)
    [ 0.000000] ACPI: FACP 000000009affb000 00010C (v05 HPQOEM SLIC-MPC 00000001 HP 00040000)
    [ 0.000000] ACPI: DSDT 000000009afe4000 0130E0 (v01 HPQOEM 181D 00000000 ACPI 00040000)
    [ 0.000000] ACPI: FACS 000000009afb8000 000040
    [ 0.000000] ACPI: UEFI 000000009affd000 000236 (v01 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: ASF! 000000009affc000 0000A5 (v32 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: HPET 000000009affa000 000038 (v01 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: APIC 000000009aff9000 00008C (v03 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: MCFG 000000009aff8000 00003C (v01 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: WDAT 000000009afe3000 000224 (v01 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: SSDT 000000009afe1000 001068 (v01 HPQOEM 181D 00001000 ACPI 00040000)
    [ 0.000000] ACPI: BOOT 000000009afdf000 000028 (v01 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: ASPT 000000009afdd000 000034 (v07 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: DBGP 000000009afdc000 000034 (v01 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: FPDT 000000009afda000 000044 (v01 HPQOEM 181D 00000001 HP 00040000)
    [ 0.000000] ACPI: MSDM 000000009afd9000 000055 (v03 HPQOEM SLIC-MPC 00000001 HP 00040000)
    [ 0.000000] ACPI: SSDT 000000009afd8000 000926 (v01 HPQOEM 181D 00003000 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 000000009afd7000 000A92 (v01 HPQOEM 181D 00003000 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 000000009afd3000 002E84 (v01 HPQOEM 181D 00001000 ACPI 00040000)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000025f5fffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x25f5fffff]
    [ 0.000000] NODE_DATA [mem 0x25f5f3000-0x25f5f7fff]
    [ 0.000000] [ffffea0000000000-ffffea00097fffff] PMD -> [ffff880256c00000-ffff88025ebfffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x25f5fffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x00090fff]
    [ 0.000000] node 0: [mem 0x00100000-0x1fffffff]
    [ 0.000000] node 0: [mem 0x20200000-0x40003fff]
    [ 0.000000] node 0: [mem 0x40005000-0x9a3befff]
    [ 0.000000] node 0: [mem 0x9afff000-0x9affffff]
    [ 0.000000] node 0: [mem 0x100000000-0x25f5fffff]
    [ 0.000000] On node 0 totalpages: 2070351
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 21 pages reserved
    [ 0.000000] DMA zone: 3984 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 9799 pages used for memmap
    [ 0.000000] DMA32 zone: 627135 pages, LIFO batch:31
    [ 0.000000] Normal zone: 22488 pages used for memmap
    [ 0.000000] Normal zone: 1439232 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
    [ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: [mem 0x00091000-0x00091fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x00092000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x40004000-0x40004fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9a3bf000-0x9aebefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9aebf000-0x9afbefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9afbf000-0x9affefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9b000000-0x9f9fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9fa00000-0xdfffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfeafffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb03fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfeb04000-0xfebfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed0ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffb7ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xffb80000-0xffffffff]
    [ 0.000000] e820: [mem 0x9fa00000-0xdfffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88025f200000 s86336 r8192 d24256 u262144
    [ 0.000000] pcpu-alloc: s86336 r8192 d24256 u262144 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2037979
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=64c5186f-288d-4708-959e-38cca5d1b5c0 rw quiet
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 8068224K/8281404K available (5270K kernel code, 836K rwdata, 1672K rodata, 1128K init, 1324K bss, 213180K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
    [ 0.000000] NR_IRQS:8448 nr_irqs:744 16
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 33554432 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.003333] tsc: Detected 2394.589 MHz processor
    [ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 4791.72 BogoMIPS (lpj=7981963)
    [ 0.000004] pid_max: default: 32768 minimum: 301
    [ 0.000023] Security Framework initialized
    [ 0.000029] AppArmor: AppArmor disabled by boot time parameter
    [ 0.000030] Yama: becoming mindful.
    [ 0.000417] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
    [ 0.001940] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.002614] Mount-cache hash table entries: 256
    [ 0.002739] Initializing cgroup subsys memory
    [ 0.002743] Initializing cgroup subsys devices
    [ 0.002744] Initializing cgroup subsys freezer
    [ 0.002746] Initializing cgroup subsys net_cls
    [ 0.002747] Initializing cgroup subsys blkio
    [ 0.002763] CPU: Physical Processor ID: 0
    [ 0.002764] CPU: Processor Core ID: 0
    [ 0.002768] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    [ 0.003048] mce: CPU supports 9 MCE banks
    [ 0.003058] CPU0: Thermal monitoring enabled (TM1)
    [ 0.003064] Last level iTLB entries: 4KB 512, 2MB 0, 4MB 0
    Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
    tlb_flushall_shift: 2
    [ 0.003142] Freeing SMP alternatives memory: 20K (ffffffff819ed000 - ffffffff819f2000)
    [ 0.003906] ACPI: Core revision 20131115
    [ 0.009053] ACPI: All ACPI Tables successfully acquired
    [ 0.053822] ftrace: allocating 21057 entries in 83 pages
    [ 0.061910] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.094942] smpboot: CPU0: Intel(R) Core(TM) i7-3630QM CPU @ 2.40GHz (fam: 06, model: 3a, stepping: 09)
    [ 0.094948] TSC deadline timer enabled
    [ 0.094955] Performance Events: PEBS fmt1+, 16-deep LBR, IvyBridge events, full-width counters, Intel PMU driver.
    [ 0.094960] ... version: 3
    [ 0.094960] ... bit width: 48
    [ 0.094961] ... generic registers: 4
    [ 0.094962] ... value mask: 0000ffffffffffff
    [ 0.094962] ... max period: 0000ffffffffffff
    [ 0.094963] ... fixed-purpose events: 3
    [ 0.094964] ... event mask: 000000070000000f
    [ 0.121742] x86: Booting SMP configuration:
    [ 0.135256] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.121746] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7
    [ 0.256907] x86: Booted up 1 node, 8 CPUs
    [ 0.256909] smpboot: Total of 8 processors activated (38328.81 BogoMIPS)
    [ 0.262487] devtmpfs: initialized
    [ 0.264464] PM: Registering ACPI NVS region [mem 0x9aebf000-0x9afbefff] (1048576 bytes)
    [ 0.265037] RTC time: 21:55:49, date: 02/28/14
    [ 0.265063] NET: Registered protocol family 16
    [ 0.265128] cpuidle: using governor ladder
    [ 0.265129] cpuidle: using governor menu
    [ 0.265147] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
    [ 0.265148] ACPI: bus type PCI registered
    [ 0.265150] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.265197] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.265199] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
    [ 0.282064] PCI: Using configuration type 1 for base access
    [ 0.282527] bio: create slab <bio-0> at 0
    [ 0.282615] ACPI: Added _OSI(Module Device)
    [ 0.282616] ACPI: Added _OSI(Processor Device)
    [ 0.282617] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.282618] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.285086] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.312765] ACPI Error: No handler for Region [RAM_] (ffff880253874090) [EmbeddedControl] (20131115/evregion-162)
    [ 0.312767] ACPI Error: Region EmbeddedControl (ID=3) has no handler (20131115/exfldio-299)
    [ 0.312770] ACPI Error: Method parse/execution failed [\_SB_.ACCL._STA] (Node ffff88025387e190), AE_NOT_EXIST (20131115/psparse-536)
    [ 0.312774] ACPI Error: Method execution failed [\_SB_.ACCL._STA] (Node ffff88025387e190), AE_NOT_EXIST (20131115/uteval-103)
    [ 0.313004] ACPI: SSDT 000000009ae3a018 00083B (v01 PmRef Cpu0Cst 00003001 INTL 20111123)
    [ 0.313310] ACPI: Dynamic OEM Table Load:
    [ 0.313311] ACPI: SSDT (null) 00083B (v01 PmRef Cpu0Cst 00003001 INTL 20111123)
    [ 0.325950] ACPI: SSDT 000000009aeada98 000303 (v01 PmRef ApIst 00003000 INTL 20111123)
    [ 0.326272] ACPI: Dynamic OEM Table Load:
    [ 0.326273] ACPI: SSDT (null) 000303 (v01 PmRef ApIst 00003000 INTL 20111123)
    [ 0.339208] ACPI: SSDT 000000009ababd98 000119 (v01 PmRef ApCst 00003000 INTL 20111123)
    [ 0.339508] ACPI: Dynamic OEM Table Load:
    [ 0.339509] ACPI: SSDT (null) 000119 (v01 PmRef ApCst 00003000 INTL 20111123)
    [ 1.238575] ACPI: Interpreter enabled
    [ 1.238580] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131115/hwxface-580)
    [ 1.238584] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
    [ 1.238594] ACPI: (supports S0 S3 S4 S5)
    [ 1.238595] ACPI: Using IOAPIC for interrupt routing
    [ 1.238612] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 1.238799] ACPI: ACPI Dock Station Driver: 1 docks/bays found
    [ 1.260983] ACPI : EC: GPE storm detected(9 GPEs), transactions will use polling mode
    [ 1.321167] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
    [ 1.321171] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 1.321214] \_SB_.PCI0:_OSC invalid UUID
    [ 1.321215] _OSC request data:1 1f 0
    [ 1.321218] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
    [ 1.321676] PCI host bridge to bus 0000:00
    [ 1.321678] pci_bus 0000:00: root bus resource [bus 00-fe]
    [ 1.321679] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 1.321680] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 1.321682] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 1.321683] pci_bus 0000:00: root bus resource [mem 0x9fa00000-0xfeafffff]
    [ 1.321688] pci 0000:00:00.0: [8086:0154] type 00 class 0x060000
    [ 1.321749] pci 0000:00:01.0: [8086:0151] type 01 class 0x060400
    [ 1.321772] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 1.321801] pci 0000:00:01.0: System wakeup disabled by ACPI
    [ 1.321826] pci 0000:00:02.0: [8086:0166] type 00 class 0x030000
    [ 1.321834] pci 0000:00:02.0: reg 0x10: [mem 0xd4000000-0xd43fffff 64bit]
    [ 1.321839] pci 0000:00:02.0: reg 0x18: [mem 0xc0000000-0xcfffffff 64bit pref]
    [ 1.321842] pci 0000:00:02.0: reg 0x20: [io 0x5000-0x503f]
    [ 1.321916] pci 0000:00:14.0: [8086:1e31] type 00 class 0x0c0330
    [ 1.321936] pci 0000:00:14.0: reg 0x10: [mem 0xd4600000-0xd460ffff 64bit]
    [ 1.322002] pci 0000:00:14.0: PME# supported from D3hot D3cold
    [ 1.322033] pci 0000:00:14.0: System wakeup disabled by ACPI
    [ 1.322061] pci 0000:00:16.0: [8086:1e3a] type 00 class 0x078000
    [ 1.322083] pci 0000:00:16.0: reg 0x10: [mem 0xd4614000-0xd461400f 64bit]
    [ 1.322154] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
    [ 1.322218] pci 0000:00:1a.0: [8086:1e2d] type 00 class 0x0c0320
    [ 1.322238] pci 0000:00:1a.0: reg 0x10: [mem 0xd4619000-0xd46193ff]
    [ 1.322321] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
    [ 1.322363] pci 0000:00:1a.0: System wakeup disabled by ACPI
    [ 1.322390] pci 0000:00:1b.0: [8086:1e20] type 00 class 0x040300
    [ 1.322404] pci 0000:00:1b.0: reg 0x10: [mem 0xd4610000-0xd4613fff 64bit]
    [ 1.322466] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 1.322498] pci 0000:00:1b.0: System wakeup disabled by ACPI
    [ 1.322527] pci 0000:00:1c.0: [8086:1e10] type 01 class 0x060400
    [ 1.322652] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 1.322697] pci 0000:00:1c.0: System wakeup disabled by ACPI
    [ 1.322726] pci 0000:00:1c.1: [8086:1e12] type 01 class 0x060400
    [ 1.322855] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [ 1.322900] pci 0000:00:1c.1: System wakeup disabled by ACPI
    [ 1.322929] pci 0000:00:1c.3: [8086:1e16] type 01 class 0x060400
    [ 1.323056] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
    [ 1.323100] pci 0000:00:1c.3: System wakeup disabled by ACPI
    [ 1.323125] pci 0000:00:1c.5: [8086:1e1a] type 01 class 0x060400
    [ 1.323197] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
    [ 1.323232] pci 0000:00:1c.5: System wakeup disabled by ACPI
    [ 1.323263] pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
    [ 1.323282] pci 0000:00:1d.0: reg 0x10: [mem 0xd4618000-0xd46183ff]
    [ 1.323366] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
    [ 1.323407] pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 1.323434] pci 0000:00:1f.0: [8086:1e57] type 00 class 0x060100
    [ 1.323584] pci 0000:00:1f.2: [8086:282a] type 00 class 0x010400
    [ 1.323601] pci 0000:00:1f.2: reg 0x10: [io 0x5088-0x508f]
    [ 1.323608] pci 0000:00:1f.2: reg 0x14: [io 0x5094-0x5097]
    [ 1.323615] pci 0000:00:1f.2: reg 0x18: [io 0x5080-0x5087]
    [ 1.323623] pci 0000:00:1f.2: reg 0x1c: [io 0x5090-0x5093]
    [ 1.323630] pci 0000:00:1f.2: reg 0x20: [io 0x5060-0x507f]
    [ 1.323637] pci 0000:00:1f.2: reg 0x24: [mem 0xd4617000-0xd46177ff]
    [ 1.323678] pci 0000:00:1f.2: PME# supported from D3hot
    [ 1.323727] pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
    [ 1.323741] pci 0000:00:1f.3: reg 0x10: [mem 0xd4615000-0xd46150ff 64bit]
    [ 1.323760] pci 0000:00:1f.3: reg 0x20: [io 0x5040-0x505f]
    [ 1.323853] pci 0000:01:00.0: [10de:0de9] type 00 class 0x030000
    [ 1.323862] pci 0000:01:00.0: reg 0x10: [mem 0xd2000000-0xd2ffffff]
    [ 1.323869] pci 0000:01:00.0: reg 0x14: [mem 0xa0000000-0xafffffff 64bit pref]
    [ 1.323875] pci 0000:01:00.0: reg 0x1c: [mem 0xb0000000-0xb1ffffff 64bit pref]
    [ 1.323880] pci 0000:01:00.0: reg 0x24: [io 0x4000-0x407f]
    [ 1.323884] pci 0000:01:00.0: reg 0x30: [mem 0xfff80000-0xffffffff pref]
    [ 1.323917] pci 0000:01:00.0: System wakeup disabled by ACPI
    [ 1.330552] pci 0000:00:01.0: PCI bridge to [bus 01-06]
    [ 1.330557] pci 0000:00:01.0: bridge window [io 0x4000-0x4fff]
    [ 1.330562] pci 0000:00:01.0: bridge window [mem 0xd2000000-0xd3ffffff]
    [ 1.330568] pci 0000:00:01.0: bridge window [mem 0xa0000000-0xbfffffff 64bit pref]
    [ 1.330681] pci 0000:00:1c.0: PCI bridge to [bus 07]
    [ 1.330867] pci 0000:08:00.0: [10ec:5229] type 00 class 0xff0000
    [ 1.330931] pci 0000:08:00.0: reg 0x10: [mem 0xd1000000-0xd1000fff]
    [ 1.331423] pci 0000:08:00.0: supports D1 D2
    [ 1.331424] pci 0000:08:00.0: PME# supported from D1 D2 D3hot
    [ 1.331502] pci 0000:08:00.0: System wakeup disabled by ACPI
    [ 1.337279] pci 0000:00:1c.1: PCI bridge to [bus 08-09]
    [ 1.337286] pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
    [ 1.337294] pci 0000:00:1c.1: bridge window [mem 0xd1000000-0xd1ffffff]
    [ 1.337304] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd0ffffff 64bit pref]
    [ 1.337465] pci 0000:0a:00.0: [8086:0887] type 00 class 0x028000
    [ 1.337511] pci 0000:0a:00.0: reg 0x10: [mem 0xd4500000-0xd4501fff 64bit]
    [ 1.337733] pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold
    [ 1.337776] pci 0000:0a:00.0: System wakeup disabled by ACPI
    [ 1.343946] pci 0000:00:1c.3: PCI bridge to [bus 0a]
    [ 1.343959] pci 0000:00:1c.3: bridge window [mem 0xd4500000-0xd45fffff]
    [ 1.344076] pci 0000:0b:00.0: [10ec:8168] type 00 class 0x020000
    [ 1.344094] pci 0000:0b:00.0: reg 0x10: [io 0x2000-0x20ff]
    [ 1.344127] pci 0000:0b:00.0: reg 0x18: [mem 0xd4404000-0xd4404fff 64bit pref]
    [ 1.344147] pci 0000:0b:00.0: reg 0x20: [mem 0xd4400000-0xd4403fff 64bit pref]
    [ 1.344234] pci 0000:0b:00.0: supports D1 D2
    [ 1.344236] pci 0000:0b:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 1.373952] pci 0000:0b:00.0: System wakeup disabled by ACPI
    [ 1.380639] pci 0000:00:1c.5: PCI bridge to [bus 0b]
    [ 1.380647] pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
    [ 1.380654] pci 0000:00:1c.5: bridge window [mem 0xd4400000-0xd44fffff]
    [ 1.381137] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
    [ 1.381174] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *10 11 12 14 15)
    [ 1.381209] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 1.381244] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
    [ 1.381278] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 1.381313] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
    [ 1.381348] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 *11 12 14 15)
    [ 1.381384] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 *11 12 14 15)
    [ 1.381615] ACPI: Enabled 5 GPEs in block 00 to 3F
    [ 1.381620] ACPI: \_SB_.PCI0: notify handler is installed
    [ 1.381661] Found 1 acpi root devices
    [ 1.381686] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
    [ 1.381736] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 1.381739] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
    [ 1.381740] vgaarb: loaded
    [ 1.381741] vgaarb: bridge control possible 0000:01:00.0
    [ 1.381741] vgaarb: no bridge control possible 0000:00:02.0
    [ 1.381759] PCI: Using ACPI for IRQ routing
    [ 1.387711] PCI: pci_cache_line_size set to 64 bytes
    [ 1.387850] e820: reserve RAM buffer [mem 0x00091800-0x0009ffff]
    [ 1.387851] e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
    [ 1.387852] e820: reserve RAM buffer [mem 0x9a3bf000-0x9bffffff]
    [ 1.387853] e820: reserve RAM buffer [mem 0x9b000000-0x9bffffff]
    [ 1.387854] e820: reserve RAM buffer [mem 0x25f600000-0x25fffffff]
    [ 1.387910] NetLabel: Initializing
    [ 1.387911] NetLabel: domain hash size = 128
    [ 1.387912] NetLabel: protocols = UNLABELED CIPSOv4
    [ 1.387923] NetLabel: unlabeled traffic allowed by default
    [ 1.387936] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
    [ 1.387940] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
    [ 1.389961] Switched to clocksource hpet
    [ 1.392856] pnp: PnP ACPI init
    [ 1.392865] ACPI: bus type PNP registered
    [ 1.392884] pnp 00:00: [dma 4]
    [ 1.392898] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 1.392912] pnp 00:01: Plug and Play ACPI device, IDs INT0800 (active)
    [ 1.392979] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 1.392999] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 1.393026] system 00:04: [io 0x1100-0x110f] has been reserved
    [ 1.393028] system 00:04: [io 0xffff] has been reserved
    [ 1.393029] system 00:04: [io 0xffff] has been reserved
    [ 1.393031] system 00:04: [io 0x0400-0x0453] could not be reserved
    [ 1.393032] system 00:04: [io 0x0458-0x047f] has been reserved
    [ 1.393033] system 00:04: [io 0x0500-0x057f] has been reserved
    [ 1.393035] system 00:04: [io 0x1200-0x1207] has been reserved
    [ 1.393036] system 00:04: [mem 0xfe800000-0xfe8001ff] has been reserved
    [ 1.393038] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 1.393055] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 1.393085] system 00:06: [io 0x0454-0x0457] has been reserved
    [ 1.393087] system 00:06: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
    [ 1.393126] pnp 00:07: Plug and Play ACPI device, IDs HPQ8001 PNP0303 (active)
    [ 1.393148] pnp 00:08: Plug and Play ACPI device, IDs SYN1e5e SYN1e00 SYN0002 PNP0f13 (active)
    [ 1.393228] system 00:09: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 1.393230] system 00:09: [mem 0xfed10000-0xfed17fff] has been reserved
    [ 1.393231] system 00:09: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 1.393233] system 00:09: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 1.393234] system 00:09: [mem 0xe0000000-0xefffffff] has been reserved
    [ 1.393235] system 00:09: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 1.393237] system 00:09: [mem 0xfed90000-0xfed93fff] has been reserved
    [ 1.393238] system 00:09: [mem 0xff000000-0xffffffff] could not be reserved
    [ 1.393239] system 00:09: [mem 0xfee00000-0xfeefffff] could not be reserved
    [ 1.393241] system 00:09: [mem 0x9fa00000-0x9fa00fff] has been reserved
    [ 1.393242] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 1.393419] system 00:0a: [mem 0x20000000-0x201fffff] has been reserved
    [ 1.393420] system 00:0a: [mem 0x40004000-0x40004fff] has been reserved
    [ 1.393422] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 1.393458] pnp 00:0b: Plug and Play ACPI device, IDs HPQ0004 (active)
    [ 1.393478] pnp: PnP ACPI: found 12 devices
    [ 1.393479] ACPI: bus type PNP unregistered
    [ 1.399368] pci 0000:01:00.0: no compatible bridge window for [mem 0xfff80000-0xffffffff pref]
    [ 1.399417] pci 0000:01:00.0: BAR 6: assigned [mem 0xb2000000-0xb207ffff pref]
    [ 1.399419] pci 0000:00:01.0: PCI bridge to [bus 01-06]
    [ 1.399420] pci 0000:00:01.0: bridge window [io 0x4000-0x4fff]
    [ 1.399422] pci 0000:00:01.0: bridge window [mem 0xd2000000-0xd3ffffff]
    [ 1.399424] pci 0000:00:01.0: bridge window [mem 0xa0000000-0xbfffffff 64bit pref]
    [ 1.399427] pci 0000:00:1c.0: PCI bridge to [bus 07]
    [ 1.399444] pci 0000:00:1c.1: PCI bridge to [bus 08-09]
    [ 1.399447] pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
    [ 1.399452] pci 0000:00:1c.1: bridge window [mem 0xd1000000-0xd1ffffff]
    [ 1.399456] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd0ffffff 64bit pref]
    [ 1.399465] pci 0000:00:1c.3: PCI bridge to [bus 0a]
    [ 1.399471] pci 0000:00:1c.3: bridge window [mem 0xd4500000-0xd45fffff]
    [ 1.399482] pci 0000:00:1c.5: PCI bridge to [bus 0b]
    [ 1.399485] pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
    [ 1.399489] pci 0000:00:1c.5: bridge window [mem 0xd4400000-0xd44fffff]
    [ 1.399497] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 1.399499] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 1.399500] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 1.399501] pci_bus 0000:00: resource 7 [mem 0x9fa00000-0xfeafffff]
    [ 1.399502] pci_bus 0000:01: resource 0 [io 0x4000-0x4fff]
    [ 1.399503] pci_bus 0000:01: resource 1 [mem 0xd2000000-0xd3ffffff]
    [ 1.399505] pci_bus 0000:01: resource 2 [mem 0xa0000000-0xbfffffff 64bit pref]
    [ 1.399506] pci_bus 0000:08: resource 0 [io 0x3000-0x3fff]
    [ 1.399507] pci_bus 0000:08: resource 1 [mem 0xd1000000-0xd1ffffff]
    [ 1.399508] pci_bus 0000:08: resource 2 [mem 0xd0000000-0xd0ffffff 64bit pref]
    [ 1.399510] pci_bus 0000:0a: resource 1 [mem 0xd4500000-0xd45fffff]
    [ 1.399511] pci_bus 0000:0b: resource 0 [io 0x2000-0x2fff]
    [ 1.399512] pci_bus 0000:0b: resource 1 [mem 0xd4400000-0xd44fffff]
    [ 1.399530] NET: Registered protocol family 2
    [ 1.399642] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
    [ 1.399750] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 1.399849] TCP: Hash tables configured (established 65536 bind 65536)
    [ 1.399860] TCP: reno registered
    [ 1.399870] UDP hash table entries: 4096 (order: 5, 131072 bytes)
    [ 1.399890] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
    [ 1.399937] NET: Registered protocol family 1
    [ 1.399946] pci 0000:00:02.0: Boot video device
    [ 1.780500] PCI: CLS 64 bytes, default 64
    [ 1.780530] Unpacking initramfs...
    [ 1.820767] Freeing initrd memory: 3200K (ffff8800379b0000 - ffff880037cd0000)
    [ 1.820771] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    [ 1.820773] software IO TLB [mem 0x963bf000-0x9a3bf000] (64MB) mapped at [ffff8800963bf000-ffff88009a3befff]
    [ 1.820794] Simple Boot Flag at 0x44 set to 0x1
    [ 1.820989] Scanning for low memory corruption every 60 seconds
    [ 1.821175] audit: initializing netlink socket (disabled)
    [ 1.821183] type=2000 audit(1393624549.773:1): initialized
    [ 1.830154] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 1.831019] zbud: loaded
    [ 1.831130] VFS: Disk quotas dquot_6.5.2
    [ 1.831155] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 1.831254] msgmni has been set to 15764
    [ 1.831287] Key type big_key registered
    [ 1.831483] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 1.831523] io scheduler noop registered
    [ 1.831524] io scheduler deadline registered
    [ 1.831539] io scheduler cfq registered (default)
    [ 1.831652] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
    [ 1.832086] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 1.832096] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 1.832122] vesafb: mode is 1920x1080x32, linelength=7680, pages=0
    [ 1.832123] vesafb: scrolling: redraw
    [ 1.832124] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 1.832682] vesafb: framebuffer at 0xc0000000, mapped to 0xffffc90010e80000, using 8128k, total 8128k
    [ 1.946268] Console: switching to colour frame buffer device 240x67
    [ 2.059378] fb0: VESA VGA frame buffer device
    [ 2.059386] intel_idle: MWAIT substates: 0x21120
    [ 2.059387] intel_idle: v0.4 model 0x3A
    [ 2.059387] intel_idle: lapic_timer_reliable_states 0xffffffff
    [ 2.059528] GHES: HEST is not enabled!
    [ 2.059562] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 2.059853] Linux agpgart interface v0.103
    [ 2.059899] rtc_cmos 00:05: RTC can wake from S4
    [ 2.060005] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
    [ 2.060033] rtc_cmos 00:05: alarms up to one month, 242 bytes nvram, hpet irqs
    [ 2.060039] Intel P-state driver initializing.
    [ 2.060046] Intel pstate controlling: cpu 0
    [ 2.060056] Intel pstate controlling: cpu 1
    [ 2.060066] Intel pstate controlling: cpu 2
    [ 2.060075] Intel pstate controlling: cpu 3
    [ 2.060081] Intel pstate controlling: cpu 4
    [ 2.060087] Intel pstate controlling: cpu 5
    [ 2.060094] Intel pstate controlling: cpu 6
    [ 2.060101] Intel pstate controlling: cpu 7
    [ 2.060170] drop_monitor: Initializing network drop monitor service
    [ 2.060205] TCP: cubic registered
    [ 2.060258] NET: Registered protocol family 10
    [ 2.060356] NET: Registered protocol family 17
    [ 2.060361] Key type dns_resolver registered
    [ 2.060562] registered taskstats version 1
    [ 2.061180] Magic number: 2:200:956
    [ 2.061210] memory memory9: hash matches
    [ 2.061260] rtc_cmos 00:05: setting system clock to 2014-02-28 21:55:50 UTC (1393624550)
    [ 2.061289] PM: Hibernation image not present or could not be loaded.
    [ 2.061821] Freeing unused kernel memory: 1128K (ffffffff818d3000 - ffffffff819ed000)
    [ 2.061822] Write protecting the kernel read-only data: 8192k
    [ 2.063314] Freeing unused kernel memory: 864K (ffff880001528000 - ffff880001600000)
    [ 2.064187] Freeing unused kernel memory: 376K (ffff8800017a2000 - ffff880001800000)
    [ 2.070995] systemd-udevd[76]: starting version 208
    [ 2.081683] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [ 2.086896] rtsx_pci 0000:08:00.0: irq 41 for MSI/MSI-X
    [ 2.086940] rtsx_pci 0000:08:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 41
    [ 2.087062] ACPI: bus type USB registered
    [ 2.087089] usbcore: registered new interface driver usbfs
    [ 2.087162] usbcore: registered new interface driver hub
    [ 2.087210] usbcore: registered new device driver usb
    [ 2.087615] SCSI subsystem initialized
    [ 2.087789] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 2.087987] ehci-pci: EHCI PCI platform driver
    [ 2.088114] ehci-pci 0000:00:1a.0: EHCI Host Controller
    [ 2.088121] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
    [ 2.088137] ehci-pci 0000:00:1a.0: debug port 2
    [ 2.088526] libata version 3.00 loaded.
    [ 2.092034] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
    [ 2.092051] ehci-pci 0000:00:1a.0: irq 16, io mem 0xd4619000
    [ 2.103911] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
    [ 2.104041] hub 1-0:1.0: USB hub found
    [ 2.104046] hub 1-0:1.0: 2 ports detected
    [ 2.104210] ehci-pci 0000:00:1d.0: EHCI Host Controller
    [ 2.104214] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
    [ 2.104225] ehci-pci 0000:00:1d.0: debug port 2
    [ 2.107112] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 2.107123] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 2.108127] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
    [ 2.108140] ehci-pci 0000:00:1d.0: irq 23, io mem 0xd4618000
    [ 2.117274] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
    [ 2.117508] hub 2-0:1.0: USB hub found
    [ 2.117514] hub 2-0:1.0: 2 ports detected
    [ 2.117750] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 2.117756] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
    [ 2.117854] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
    [ 2.117873] xhci_hcd 0000:00:14.0: irq 42 for MSI/MSI-X
    [ 2.118100] hub 3-0:1.0: USB hub found
    [ 2.118108] hub 3-0:1.0: 4 ports detected
    [ 2.118349] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 2.118351] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
    [ 2.118452] hub 4-0:1.0: USB hub found
    [ 2.118462] hub 4-0:1.0: 4 ports detected
    [ 2.135939] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 2.150760] ahci 0000:00:1f.2: version 3.0
    [ 2.150968] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X
    [ 2.164071] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x11 impl RAID mode
    [ 2.164079] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst
    [ 2.171405] scsi0 : ahci
    [ 2.171666] scsi1 : ahci
    [ 2.171894] scsi2 : ahci
    [ 2.172116] scsi3 : ahci
    [ 2.172313] scsi4 : ahci
    [ 2.172447] scsi5 : ahci
    [ 2.172504] ata1: SATA max UDMA/133 abar m2048@0xd4617000 port 0xd4617100 irq 43
    [ 2.172514] ata2: DUMMY
    [ 2.172516] ata3: DUMMY
    [ 2.172517] ata4: DUMMY
    [ 2.172519] ata5: SATA max UDMA/133 abar m2048@0xd4617000 port 0xd4617300 irq 43
    [ 2.172520] ata6: DUMMY
    [ 2.410959] usb 1-1: new high-speed USB device number 2 using ehci-pci
    [ 2.491002] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 2.491072] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 2.502872] ata1.00: ATA-8: OCZ-AGILITY3, 2.22, max UDMA/133
    [ 2.502878] ata1.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 2.506430] ata5.00: ATAPI: hp DVD-RAM UJ8D1, H.01, max UDMA/100
    [ 2.512780] ata1.00: configured for UDMA/133
    [ 2.513113] scsi 0:0:0:0: Direct-Access ATA OCZ-AGILITY3 2.22 PQ: 0 ANSI: 5
    [ 2.524950] ata5.00: configured for UDMA/100
    [ 2.531477] scsi 4:0:0:0: CD-ROM hp DVD-RAM UJ8D1 H.01 PQ: 0 ANSI: 5
    [ 2.534925] hub 1-1:1.0: USB hub found
    [ 2.534975] hub 1-1:1.0: 6 ports detected
    [ 2.536606] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
    [ 2.536677] sd 0:0:0:0: [sda] Write Protect is off
    [ 2.536680] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.536701] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.537540] sda: sda1 sda2 < sda5 sda6 > sda3 sda4
    [ 2.538190] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 2.542465] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    [ 2.542469] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.542686] sr 4:0:0:0: Attached scsi CD-ROM sr0
    [ 2.608731] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
    [ 2.651327] systemd[1]: systemd 208 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
    [ 2.651588] systemd[1]: No hostname configured.
    [ 2.651596] systemd[1]: Set hostname to <localhost>.
    [ 2.653530] random: systemd urandom read with 42 bits of entropy available
    [ 2.657173] systemd-fstab-generator[151]: Checking was requested for "nas:/mnt/HD/HD_a2/STORE01", but it is not a device.
    [ 2.687501] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
    [ 2.687558] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 2.687572] systemd[1]: Starting Login Prompts.
    [ 2.687585] systemd[1]: Reached target Login Prompts.
    [ 2.687595] systemd[1]: Starting Remote File Systems.
    [ 2.687605] systemd[1]: Reached target Remote File Systems.
    [ 2.687615] systemd[1]: Starting Device-mapper event daemon FIFOs.
    [ 2.687642] systemd[1]: Listening on Device-mapper event daemon FIFOs.
    [ 2.687652] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
    [ 2.687669] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 2.687679] systemd[1]: Starting LVM2 metadata daemon socket.
    [ 2.687712] systemd[1]: Listening on LVM2 metadata daemon socket.
    [ 2.687722] systemd[1]: Starting Delayed Shutdown Socket.
    [ 2.687759] systemd[1]: Listening on Delayed Shutdown Socket.
    [ 2.687772] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
    [ 2.687812] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [ 2.687822] systemd[1]: Starting Paths.
    [ 2.687832] systemd[1]: Reached target Paths.
    [ 2.687842] systemd[1]: Starting Journal Socket.
    [ 2.687878] systemd[1]: Listening on Journal Socket.
    [ 2.687895] systemd[1]: Mounting Debug File System...
    [ 2.688266] systemd[1]: Starting Journal Service...
    [ 2.688521] systemd[1]: Started Journal Service.
    [ 2.694471] usb 3-3: new full-speed USB device number 2 using xhci_hcd
    [ 2.702863] systemd-journald[157]: Vacuuming done, freed 0 bytes
    [ 2.708483] FS-Cache: Loaded
    [ 2.710845] usb 3-3: ep 0x85 - rounding interval to 64 microframes, ep desc says 80 microframes
    [ 2.713390] RPC: Registered named UNIX socket transport module.
    [ 2.713392] RPC: Registered udp transport module.
    [ 2.713393] RPC: Registered tcp transport module.
    [ 2.713394] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 2.718880] FS-Cache: Netfs 'nfs' registered for caching
    [ 2.728296] EXT4-fs (sda1): re-mounted. Opts: data=ordered
    [ 2.741906] systemd-udevd[202]: starting version 208
    [ 2.779466] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
    [ 2.780942] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20131115/utaddress-251)
    [ 2.780948] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 2.780952] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20131115/utaddress-251)
    [ 2.780955] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \_SB_.GPIO 2 (20131115/utaddress-251)
    [ 2.780958] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \_SB_.PCI0.PEG0.PEGP.GPIO 3 (20131115/utaddress-251)
    [ 2.780961] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 2.780963] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 1 (20131115/utaddress-251)
    [ 2.780966] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \_SB_.GPIO 2 (20131115/utaddress-251)
    [ 2.780969] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \_SB_.PCI0.PEG0.PEGP.GPIO 3 (20131115/utaddress-251)
    [ 2.780971] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 2.780973] lpc_ich: Resource conflict(s) found affecting gpio_ich
    [ 2.782830] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 2.785766] mei_me 0000:00:16.0: irq 44 for MSI/MSI-X
    [ 2.791210] ACPI: Lid Switch [LID0]
    [ 2.791504] [drm] Initialized drm 1.1.0 20060810
    [ 2.791605] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    [ 2.791609] ACPI: Power Button [PWRF]
    [ 2.792665] wmi: Mapper loaded
    [ 2.792681] hp_accel: laptop model unknown, using default axes configuration
    [ 2.797256] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
    [ 2.802959] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
    [ 2.802966] r8169 0000:0b:00.0: can't disable ASPM; OS doesn't have ASPM control
    [ 2.803223] r8169 0000:0b:00.0: irq 46 for MSI/MSI-X
    [ 2.803494] r8169 0000:0b:00.0 eth0: RTL8168evl/8111evl at 0xffffc90011eee000, a0:b3:cc:4b:1a:7e, XID 0c900800 IRQ 46
    [ 2.803496] r8169 0000:0b:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
    [ 2.811332] cfg80211: Calling CRDA to update world regulatory domain
    [ 2.815328] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4
    [ 2.816642] Intel(R) Wireless WiFi driver for Linux, in-tree:
    [ 2.816644] Copyright(c) 2003-2013 Intel Corporation
    [ 2.816736] iwlwifi 0000:0a:00.0: can't disable ASPM; OS doesn't have ASPM control
    [ 2.816860] iwlwifi 0000:0a:00.0: irq 47 for MSI/MSI-X
    [ 2.817888] usb 2-1: new high-speed USB device number 2 using ehci-pci
    [ 2.818258] microcode: CPU0 sig=0x306a9, pf=0x10, revision=0x12
    [ 2.818636] platform microcode: Direct firmware load failed with error -2
    [ 2.818639] platform microcode: Falling back to user helper
    [ 2.821802] iwlwifi 0000:0a:00.0: loaded firmware version 18.168.6.1 op_mode iwldvm
    [ 2.824537] tsc: Refined TSC clocksource calibration: 2394.561 MHz
    [ 2.826546] hidraw: raw HID events driver (C) Jiri Kosina
    [ 2.828014] usbcore: registered new interface driver usbhid
    [ 2.828016] usbhid: USB HID core driver
    [ 2.832266] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
    [ 2.832334] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
    [ 2.832373] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
    [ 2.832658] ACPI Warning: 0x0000000000005040-0x000000000000505f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20131115/utaddress-251)
    [ 2.832662] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 2.834846] iwlwifi 0000:0a:00.0: CONFIG_IWLWIFI_DEBUG disabled
    [ 2.834848] iwlwifi 0000:0a:00.0: CONFIG_IWLWIFI_DEBUGFS disabled
    [ 2.834850] iwlwifi 0000:0a:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled
    [ 2.834851] iwlwifi 0000:0a:00.0: Detected Intel(R) Centrino(R) Wireless-N 2230 BGN, REV=0xC8
    [ 2.834955] iwlwifi 0000:0a:00.0: L1 Enabled; Disabling L0S
    [ 2.835666] usbcore: registered new interface driver snd-usb-audio
    [ 2.854044] iTCO_vendor_support: vendor-support=0
    [ 2.854466] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
    [ 2.854514] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
    [ 2.854638] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 2.856761] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
    [ 2.860498] microcode: CPU1 sig=0x306a9, pf=0x10, revision=0x12
    [ 2.860514] platform microcode: Direct firmware load failed with error -2
    [ 2.860516] platform microcode: Falling back to user helper
    [ 2.863566] input: Burr-Brown from TI USB Audio CODEC as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3:1.3/input/input10
    [ 2.863734] hid-generic 0003:08BB:2902.0001: input,hidraw0: USB HID v1.00 Device [Burr-Brown from TI USB Audio CODEC ] on usb-0000:00:14.0-3/input3
    [ 2.867484] microcode: CPU2 sig=0x306a9, pf=0x10, revision=0x12
    [ 2.867498] platform microcode: Direct firmware load failed with error -2
    [ 2.867500] platform microcode: Falling back to user helper
    [ 2.870088] microcode: CPU3 sig=0x306a9, pf=0x10, revision=0x12
    [ 2.870100] platform microcode: Direct firmware load failed with error -2
    [ 2.870102] platform microcode: Falling back to user helper
    [ 2.870542] microcode: CPU4 sig=0x306a9, pf=0x10, revision=0x12
    [ 2.870561] platform microcode: Direct firmware load failed with error -2
    [ 2.870563] platform microcode: Falling back to user helper
    [ 2.871275] microcode: CPU5 sig=0x306a9, pf=0x10, revision=0x12
    [ 2.871285] platform microcode: Direct firmware load failed with error -2
    [ 2.871288] platform microcode: Falling back to user helper
    [ 2.871938] microcode: CPU6 sig=0x306a9, pf=0x10, revision=0x12
    [ 2.871949] platform microcode: Direct firmware load failed with error -2
    [ 2.871952] platform microcode: Falling back to user helper
    [ 2.872242] microcode: CPU7 sig=0x306a9, pf=0x10, revision=0x12
    [ 2.872254] platform microcode: Direct firmware load failed with error -2
    [ 2.872257] platform microcode: Falling back to user helper
    [ 2.872575] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 2.878423] systemd-udevd[206]: renamed network interface eth0 to eno1
    [ 2.881987] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 2.890802] systemd-journald[157]: Received request to flush runtime journal from PID 1
    [ 2.901323] systemd-udevd[217]: renamed network interface wlan0 to wlo1
    [ 2.908030] ACPI: AC Adapter [ADP1] (on-line)
    [ 2.941825] hub 2-1:1.0: USB hub found
    [ 2.941930] hub 2-1:1.0: 8 ports detected
    [ 3.021509] usb 1-1.1: new full-speed USB device number 3 using ehci-pci
    [ 3.061674] intel_rapl: domain uncore energy ctr 8617:8617 not working, skip
    [ 3.074806] lis3lv02d: 8 bits 3DC sensor found
    [ 3.135241] iwlwifi 0000:0a:00.0: L1 Enabled; Disabling L0S
    [ 3.142912] iwlwifi 0000:0a:00.0: Radio type=0x2-0x0-0x0
    [ 3.171642] usb 1-1.3: new high-speed USB device number 4 using ehci-pci
    [ 3.233041] nvidia: module license 'NVIDIA' taints kernel.
    [ 3.233045] Disabling lock debugging due to kernel taint
    [ 3.238226] nvidia 0000:01:00.0: enabling device (0006 -> 0007)
    [ 3.238279] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=none
    [ 3.238457] [drm] Initialized nvidia-drm 0.0.0 20130102 for 0000:01:00.0 on minor 0
    [ 3.238462] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 331.38 Wed Jan 8 19:32:30 PST 2014
    [ 3.356112] media: Linux media interface: v0.10
    [ 3.360422] Linux video capture interface: v2.00
    [ 3.365597] uvcvideo: Found UVC 1.00 device HP Truevision HD (05c8:033a)
    [ 3.377291] input: HP Truevision HD as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input11
    [ 3.377488] usbcore: registered new interface driver uvcvideo
    [ 3.377494] USB Video Class driver (1.1.1)
    [ 3.393157] iwlwifi 0000:0a:00.0: L1 Enabled; Disabling L0S
    [ 3.400907] iwlwifi 0000:0a:00.0: Radio type=0x2-0x0-0x0
    [ 3.425257] usb 2-1.6: new full-speed USB device number 3 using ehci-pci
    [ 3.458983] input: HP WMI hotkeys as /devices/virtual/input/input9
    [ 3.473371] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
    [ 3.521478] Bluetooth: Core ver 2.17
    [ 3.521492] NET: Registered protocol family 31
    [ 3.521493] Bluetooth: HCI device and connection manager initialized
    [ 3.521499] Bluetooth: HCI socket layer initialized
    [ 3.521501] Bluetooth: L2CAP socket layer initialized
    [ 3.521505] Bluetooth: SCO socket layer initialized
    [ 3.523209] usbcore: registered new interface driver btusb
    [ 3.597251] r8169 0000:0b:00.0 eno1: link down
    [ 3.597286] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
    [ 3.825665] Switched to clocksource tsc
    [ 4.034513] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x26c00, board id: 2055, fw id: 1107424
    [ 4.062727] nvidia 0000:01:00.0: irq 48 for MSI/MSI-X
    [ 4.071722] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
    [ 4.071771] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
    [ 4.071795] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
    [ 4.071832] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
    [ 4.071854] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
    [ 4.071876] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
    [ 4.071922] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
    [ 4.071944] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
    [ 4.104186] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
    [ 4.107557] mousedev: PS/2 mouse device common for all mice
    [ 4.326086] thermal LNXTHERM:00: registered as thermal_zone1
    [ 4.326092] ACPI: Thermal Zone [TZS0] (69 C)
    [ 4.606281] [Firmware Bug]: No valid trip found
    [ 5.280111] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input12
    [ 5.283560] random: nonblocking pool is initialized
    [ 5.694087] ACPI: Battery Slot [BAT0] (battery present)
    [ 7.035020] thermal LNXTHERM:02: registered as thermal_zone2
    [ 7.035026] ACPI: Thermal Zone [TZS2] (57 C)
    [ 8.889924] thermal LNXTHERM:03: registered as thermal_zone3
    [ 8.889929] ACPI: Thermal Zone [TZS3] (30 C)
    [ 9.408442] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
    [ 10.251376] type=1006 audit(1393624558.679:2): pid=348 uid=0 old auid=4294967295 new auid=120 old ses=4294967295 new ses=1 res=1
    [ 11.338226] traps: gnome-shell[416] trap int3 ip:7f1024ce4289 sp:7fffc13c81f0 error:0
    [ 33.022441] type=1006 audit(1393624581.429:3): pid=439 uid=0 old auid=4294967295 new auid=1001 old ses=4294967295 new ses=2 res=1
    [ 33.028194] type=1006 audit(1393624581.436:4): pid=440 uid=0 old auid=4294967295 new auid=1001 old ses=4294967295 new ses=3 res=1
    lsmod
    Module Size Used by
    joydev 9631 0
    mousedev 10247 0
    btusb 19648 0
    bluetooth 326343 2 btusb
    uvcvideo 72804 0
    videobuf2_vmalloc 3304 1 uvcvideo
    videobuf2_memops 2335 1 videobuf2_vmalloc
    videobuf2_core 28243 1 uvcvideo
    videodev 111840 2 uvcvideo,videobuf2_core
    media 11719 2 uvcvideo,videodev
    nvidia 10621191 29
    intel_rapl 11776 0
    x86_pkg_temp_thermal 6991 0
    intel_powerclamp 8802 0
    coretemp 6358 0
    kvm_intel 131532 0
    kvm 396221 1 kvm_intel
    crct10dif_pclmul 4682 0
    crct10dif_common 1372 1 crct10dif_pclmul
    crc32_pclmul 2923 0
    crc32c_intel 14185 0
    ghash_clmulni_intel 4405 0
    aesni_intel 45548 0
    aes_x86_64 7399 1 aesni_intel
    lrw 3565 1 aesni_intel
    gf128mul 5858 1 lrw
    glue_helper 4417 1 aesni_intel
    ablk_helper 2004 1 aesni_intel
    cryptd 8409 3 ghash_clmulni_intel,aesni_intel,ablk_helper
    hid_generic 1153 0
    hp_wmi 7595 0
    sparse_keymap 3146 1 hp_wmi
    arc4 2000 2
    iTCO_wdt 5407 0
    iTCO_vendor_support 1929 1 iTCO_wdt
    mxm_wmi 1467 0
    iwldvm 167738 0
    mac80211 474681 1 iwldvm
    snd_usb_audio 117811 0
    usbhid 40545 0
    snd_usbmidi_lib 19755 1 snd_usb_audio
    hid 90902 2 hid_generic,usbhid
    snd_rawmidi 18742 1 snd_usbmidi_lib
    snd_seq_device 5180 1 snd_rawmidi
    microcode 15216 0
    evdev 11045 11
    psmouse 88171 0
    snd_hda_codec_hdmi 36379 1
    iwlwifi 140193 1 iwldvm
    serio_raw 5009 0
    snd_hda_codec_idt 43508 1
    cfg80211 408199 3 iwlwifi,mac80211,iwldvm
    i2c_i801 11269 0
    rtsx_pci_ms 7258 0
    r8169 58423 0
    memstick 7504 1 rtsx_pci_ms
    rfkill 15651 4 cfg80211,hp_wmi,bluetooth
    mii 4027 1 r8169
    thermal 8556 0
    snd_hda_intel 37352 0
    snd_hda_codec 150017 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel
    intel_gtt 12664 0
    drm_kms_helper 35710 0
    snd_hwdep 6332 2 snd_usb_audio,snd_hda_codec
    drm 239102 3 drm_kms_helper,nvidia
    battery 7565 0
    snd_pcm 77822 4 snd_usb_audio,snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
    ac 3334 0
    snd_page_alloc 7298 2 snd_pcm,snd_hda_intel
    snd_timer 18718 1 snd_pcm
    hp_accel 16520 0
    i2c_algo_bit 5391 0
    mei_me 9552 0
    i2c_core 24760 6 drm,i2c_i801,drm_kms_helper,i2c_algo_bit,nvidia,videodev
    lis3lv02d 11283 1 hp_accel
    input_polldev 2818 1 lis3lv02d
    snd 59029 11 snd_usb_audio,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_idt,snd_pcm,snd_rawmidi,snd_usbmidi_lib,snd_hda_codec,snd_hda_intel,snd_seq_device
    shpchp 25425 0
    mei 62867 1 mei_me
    wmi 8251 2 hp_wmi,mxm_wmi
    video 11425 0
    soundcore 5418 1 snd
    lpc_ich 13368 0
    processor 24620 0
    button 4605 0
    nfs 191568 0
    lockd 76942 1 nfs
    sunrpc 233786 2 nfs,lockd
    fscache 47797 1 nfs
    ext4 473259 2
    crc16 1359 2 ext4,bluetooth
    mbcache 6074 1 ext4
    jbd2 80912 1 ext4
    sr_mod 14930 0
    cdrom 34880 1 sr_mod
    sd_mod 31361 3
    atkbd 16806 0
    libps2 4187 2 atkbd,psmouse
    rtsx_pci_sdmmc 13911 0
    mmc_core 95465 1 rtsx_pci_sdmmc
    ahci 23048 2
    libahci 21698 1 ahci
    libata 172104 2 ahci,libahci
    ehci_pci 3928 0
    xhci_hcd 144553 0
    ehci_hcd 64171 1 ehci_pci
    scsi_mod 132250 3 libata,sd_mod,sr_mod
    rtsx_pci 32241 2 rtsx_pci_ms,rtsx_pci_sdmmc
    usbcore 180208 8 btusb,snd_usb_audio,uvcvideo,snd_usbmidi_lib,ehci_hcd,ehci_pci,usbhid,xhci_hcd
    usb_common 1648 1 usbcore
    i8042 13366 1 libps2
    serio 10721 6 serio_raw,atkbd,i8042,psmouse

  • Fax is not working on H323

    Hello All,
    I have an issue with fax, it is connected to an fxs port on my h323 gateway. When a call comes from PRI and get connected to fax after I hear the fax tone the fax drops. IOS is Version 15.0(1)M4, and DSP is PVDM3.
    My analysis:
    The external calls hit gateway and it matches the pots dialpeer where my fax connected to. From the "debug voip vtsp all", I see Primary Fax Protocol=CISCO_FAX_RELAY, which is not enabled and we are using T38 relay and modem passthrough method for faxing. I believe PVDM3 does not work with Cisco Relay and couldn't allocate any dsp resources for the call and it drops. But still I wonder how gateway takes cisco relay.
    Config:
    voice service voip
    allow-connections h323 to h323
    fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
    h323
      emptycapability
    modem passthrough nse codec g711ulaw
    dial-peer voice 1001 pots
    tone ringback alert-no-PI
    description PSTN Incoming, Pattern:.
    translation-profile incoming PSTN-to-PhoneDN
    incoming called-number .
    direct-inward-dial
    dial-peer voice 999030 pots
    tone ringback alert-no-PI
    destination-pattern 3027898
    progress_ind setup enable 3
    port 0/3/0
    Output of vtsp debug
    Oct  4 20:30:07: //6824/97F0D7BD8350/VTSP:(0/1/0:15):7:1:1/vtsp_dsm_save_fax_config: 
       Fax Relay=ENABLED
       Primary Fax Protocol=CISCO_FAX_RELAY, Fallback Fax Protocol=NONE_FAX_RELAY
       Fax Relay CM Suppression :=ENABLED, Fax Relay ANS Suppression :=DISABLED
       Fax Parameters Set By=Dialpeer, Peer=999030 (this is the peer where my fax connected to)
    I have converted the port to MGCP and found its working, while faxing I see vtsp outputs
    Oct  4 23:57:29: //7181/8FE17FEF8379/VTSP:(0/3/0):-1:1:2/vtsp_dsm_save_fax_config:
       Fax Relay=DISABLED - MGCP Application
       Primary Fax Protocol=IGNORE_FAX_RELAY, Fallback Fax Protocol=IGNORE_FAX_RELAY
       Fax Relay CM Suppression :=ENABLED, Fax Relay ANS Suppression :=DISABLED
       Fax Parameters Set By=MGCP Call Type --> I believe MGCP disabled the cisco fax relay and switch over to T38.
    Oct  4 23:57:40: //7181/8FE17FEF8379/VTSP:(0/3/0):-1:1:2/vtsp_dsm_save_fax_config:
       Fax Relay=ENABLED
       Primary Fax Protocol=T38_FAX_RELAY, Fallback Fax Protocol=NONE_FAX_RELAY
       Fax Relay CM Suppression :=ENABLED, Fax Relay ANS Suppression :=DISABLED
       Fax Parameters Set By=MGCP Call Type
    Can some one kindly suggest how to make it work on H323, also how we can force disabling cisco fax relay?

    As I mentioned earlier, we are using MGCP for that particular fax port and the gateway we use as H323.
    Even I'm not pretty sure about using mixed protocol, I believe this gateway gonna used to support call center calls. SInce MGCP is easy for configs they might have confiugred only the port as MGCP endpoint.
    Now its not working with both the cases, not in mgcp as well as fallback mode. Can you reveiw the debugs and see why I have to remove "modem passthrough" command from voice service voip section which of our standard config and works well with all other gateway of ours. Please help here.

  • Blazeds 4.0.0.7548 is not working on Websphere over HTTPS protocol

    Hi All
    Our application is on Blazeds 4.0.0.7548 deployed on websphere 7.0.  While this application works fine on HTTP but it doesn't work consistently on HTTPS.  It throws following exception
    FaultEvent fault=[RPC Fault faultString="error" faultCode="Channel.Call.Failed" faultDetail="NetConnection.Call.Failed: HTTP: Failed"] messageId="C6ABB836-C505-CAFC-F114-0006E0E0305F" type="fault" bubbles=false cancelable=true eventPhase=2.
    Following is the screeshot
    I don't see any exception in the logs as well.
    HTTP works fine, i only see this exception on HTTPS.
    Regards
    Ravi

    As I mentioned earlier, we are using MGCP for that particular fax port and the gateway we use as H323.
    Even I'm not pretty sure about using mixed protocol, I believe this gateway gonna used to support call center calls. SInce MGCP is easy for configs they might have confiugred only the port as MGCP endpoint.
    Now its not working with both the cases, not in mgcp as well as fallback mode. Can you reveiw the debugs and see why I have to remove "modem passthrough" command from voice service voip section which of our standard config and works well with all other gateway of ours. Please help here.

  • Project on demand/click to run not working in Project Online

    Do I need to do anything special to allow the click to run functionality in Project Online to work? Or does it not work for Project Online?
    We have a Project Online trial, but when the users who do not have Project Pro on their desktops, try to select Edit the project in Project Pro, they get an error saying that Project Pro needs to be installed first.
    I would have expected click to run to download it.
    I feel I may be missing something basic here.
    Any advice please?
    Ryan

    Project Online in itself is not sufficient.  You need Project Online with Project Pro for 0365, or another Office 0365 sku that includes Project Pro.
    Assuming you have either of these, then the admin has to assign the Project Pro licence to the user (admin | users and groups)
    Check out the following screen shot
    Ben Howard [MVP] | web |
    blog | book

  • (Pulse)Audio? not working (Intel HDMI)

    Hi,
    so I installed Arch Linux again and have problems with the sound. I think there is a problem with PulseAudio, as test sounds from settings (cinnamon) and using 'aplay -D plughw:0,7 /usr/share/sounds/alsa/Front_Center.wav' work. But when I open music/videos in VLC, Firefox or Clementine, there is no sound, nor are system sounds output.
    I tried using headphones and everything works just fine.
    I've been searching for a while now and found nothing that could help me. I can't figure out, what's wrong.
    Previously I used an AMD graphics card and had no problems with sound and HDMI. Also I can't remember doing something special when I installed and used Arch back then. Now I use the HD3000 graphics included in my Intel Core i7-2600k. I need HDMI because I use an A/V-receiver.
    Thank you in advance

    There is already a default sink set under ~/.config/pulse, content: "alsa_output.pci-0000_00_1b.0.hdmi-surround-extra1". Don't know what to do with that. I thought it was set by pavucontrol and should be right?
    speaker-test -c 2 -t wav -D plug:dmix:"{CARD 0 DEV 7}"
    works (while pulseaudio is killed, right!?) in multiple instances, fuser gives
    $ fuser -v /dev/snd/*
    USER PID ACCESS COMMAND
    /dev/snd/pcmC0D7p: iuno 3431 F...m speaker-test
    iuno 3486 F...m speaker-test
    iuno 3491 F...m speaker-test
    /dev/snd/timer: iuno 3431 f.... speaker-test
    iuno 3486 f.... speaker-test
    iuno 3491 f.... speaker-test
    I see no problem there?
    I don't really know what you mean with the linked post. But I think a summary might be useful, as I really messed up writing in this thread.
    When pulseaudio is killed:
    Like mentioned above, speaker-test works with C0D7
    VLC with Preferences - Audio - Output module set to 'Alsa audio output', Device set to 'HDA Intel PCH, HDMI 0 Audio Output' works
    Clementine with GStreamer Audio Engine - Output plugin set to 'Audio sink (ALSA)' does not work
    While trying with ALSA-only I found this out:
    $ fuser -v /dev/snd/*
    USER PID ACCESS COMMAND
    /dev/snd/controlC0: iuno 652 F.... firefox
    iuno 4167 F.... vlc
    iuno 4259 F.... clementine
    /dev/snd/pcmC0D0p: iuno 652 F...m firefox
    iuno 4259 F...m clementine
    /dev/snd/pcmC0D7p: iuno 4167 F...m vlc
    /dev/snd/timer: iuno 652 f.... firefox
    iuno 4259 f.... clementine
    Concluding Clementine and Firefox use the wrong device. I guess c0d0 may be the default device for alsa? But for pulseaudio it shouldn't matter, right?
    Choosing 'HDA Intel PCH, ALC893 Analog Output' as device in VLC results in no sound, obviously, and 'C0D0' in fuser.
    However, trying to play back compressed audio with VLC, alsa-only, everything like above does not work. fuser shows the same (C0D7), vlc shows no error playing back .m4a or .mp3 files but it stays quiet.
    .oga (vorbis) files I found in /usr/share/sounds/freedesktop do work, though. While VLC is playing, I can't run speaker-test (error: -16,Device or resource busy)
    When PulseAudio comes in , some things change, obviously
    I'd like to name two states. State 1 meanns sound is working, state 2 means sound is not working. State 1 is default.
    First of all, no matter what I do, fuser always gives
    $ fuser -v /dev/snd/*
    USER PID ACCESS COMMAND
    /dev/snd/controlC0: iuno 5552 F.... pulseaudio
    /dev/snd/pcmC0D7p: iuno 5552 F...m pulseaudio
    Forcing VLC to use 'Alsa audio output'-module, and 'HDA Intel PCH, HDMI 0 Audio Output' as device results in device or resource busy error.
    Setting device to 'PulseAudio Sound Server' or 'Default ALSA Output (currently PulseAudio Sound Server)' both work. The 'Module' setting in preferences does not matter. I could either choose ALSA or Pulse with the same effect*. Long story short, audio output works, still not with compressed audio files. This means the state switches to state 2, as long as I keep the .wav file running! -> clementine and firefox also could play back sound, vlc can now also play back compressed audio - as long as I keep at least one of them running. When all sound output is paused, I fall back to state 1. Only playing back a .wav file in VLC or (p)aplay could save me back to state 2. I have to start other apps immediately, when in state 1 as pausing playback instantly causes a fallback to state 1. Opening pavucontrol, while in state 2 keeps me in state 2 as long as pavucontrol stays open. I used this as a dirty workaround for the last days.
    State changes are also blocked the other way round. While in state 1, trying to play sound from clementine or opening pavucontrol results as staying in state 1, also when I play a .wav file with vlc.
    Sorry that was much text, but I hope it's clearer now
    *correction: This setting needs a restart of vlc to take effect. When the 'Module' is set to ALSA, pavucontrol lists 'ALSA plug-in [vlc]: ALSA Playback', when set to pulseaudio, the entry is called 'VLC media player: audio stream'. Same for clementine, when I change from ALSA to pulseaudio in the settings. Firefox always uses ALSA. However, it does not have effect on the state-thing. I still need to enter state 2 with the methods mentioned above
    Last edited by iuno (2014-08-11 11:20:44)

  • Cisco CP-78XX SIP Phone Pickup Not Work on CME

    Hi,
    I configured some SIP phones (CP-7821, CP-7841) with pickup function. Is it the Pickup / GPickup soft keys not function as the SIP phone? If yes, then I can use the FAC to access that? And I tried the FAC std. / custom as the pickup / gpickup  .. both not work ... I don't know how to use the FAC on CME? As the FAC std., if I pickup local, that I should press (**3) > call?
    Ref.:
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmecover.html#45535
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmefacs.html#30064
    This is the configuration:
    CME-SIP-Phone#sh run
    Building configuration...
    Current configuration : 5413 bytes
    ! Last configuration change at 11:06:12 UTC Fri Nov 28 2014 by mtlops
    version 15.4
    no service pad
    service tcp-keepalives-in
    service tcp-keepalives-out
    service timestamps debug datetime msec localtime show-timezone
    service timestamps log datetime msec localtime show-timezone
    service password-encryption
    service sequence-numbers
    hostname CME-SIP-Phone
    boot-start-marker
    boot system flash:c2900-universalk9-mz.SPA.154-2.T1.bin
    boot-end-marker
    ! card type command needed for slot/vwic-slot 0/0
    enable secret 5 $XXXXXXXXXXXXXXXXXXXXXXXX
    aaa new-model
    aaa authentication login default local
    aaa authorization console
    aaa authorization exec default local
    aaa session-id common
    ip cef
    no ipv6 cef
    multilink bundle-name authenticated
    stcapp feature access-code
    voice-card 0
     dspfarm
     dsp services dspfarm
    voice service pots
    voice service voip
     ip address trusted list
      ipv4 10.118.0.0 255.255.255.0
     allow-connections h323 to h323
     allow-connections h323 to sip
     allow-connections sip to h323
     allow-connections sip to sip
     supplementary-service h450.12
     no supplementary-service h225-notify cid-update
     redirect ip2ip
     fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
     h323
      no h225 timeout keepalive
      call preserve
     sip
      bind control source-interface GigabitEthernet0/0
      bind media source-interface GigabitEthernet0/0
      registrar server expires max 600 min 60
    voice class codec 1
     codec preference 1 g711ulaw
     codec preference 2 g711alaw
     codec preference 3 g729r8
    voice class h323 1
      h225 timeout tcp establish 3
      call preserve
    voice class custom-cptone ABC-Company
     dualtone disconnect
      frequency 425
      cadence 500 500
    voice register pool-type  7821
     description Cisco IP Phone 7821
     reference-pooltype 6921
    voice register pool-type  7841
     description Cisco IP Phone 7841
     reference-pooltype 6941
    voice register global
     mode  cme
     source-address 10.118.0.10 port 5060
     timeouts interdigit 2
     max-dn 200
     max-pool 100
     authenticate register
     authenticate realm all
     timezone 42
     time-format 24
     date-format D/M/Y
     mwi stutter
     mwi reg-e164
     voicemail 5000
     call-feature-uri pickup http://10.118.0.10/pickup
     call-feature-uri gpickup http://10.118.0.10/gpickup
     tftp-path flash:
     file text
     create profile sync 0001170446349417
     ntp-server 10.118.0.10 mode unicast
     ip qos dscp af11 media
     ip qos dscp cs2 signal
     ip qos dscp af43 video
     ip qos dscp 25 service
     camera
     video
    voice register dn  2
     number 1000
     pickup-call any-group
     pickup-group 1
     name BB Leung
     label BB Leung
    voice register dn  3
     number 1001
     pickup-call any-group
     pickup-group 1
     name CC Chan
     label CC Chan
    voice register dn  4
     number 1002
     pickup-call any-group
     pickup-group 1
     name DD Leung
     label DD Leung
    voice register dn  50
     mwi
    voice register template  1
     softkeys hold  Newcall Resume
     softkeys idle  Newcall Redial Gpickup Pickup Cfwdall DND
     softkeys seized  Cfwdall Endcall Redial
     softkeys connected  Confrn Endcall Hold Trnsfer
    voice register pool  1
     busy-trigger-per-button 1
     id mac A8XX.XXXX.XXXX
     type 7841
     number 1 dn 2
     template 1
     dtmf-relay sip-notify
     username 1001 password 112233
     codec g711ulaw
     no vad
    voice register pool  2
     busy-trigger-per-button 1
     id mac 50XX.XXXX.XXXX
     type 7841
     number 1 dn 3
     template 1
     dtmf-relay sip-notify
     username 1002 password 112233
     codec g711ulaw
     no vad
    voice register pool  3
     busy-trigger-per-button 1
     id mac 00XX.XXXX.XXXX
     type 7821
     number 1 dn 4
     template 1
     dtmf-relay sip-notify
     username 1003 password 112233
     codec g711ulaw
     no vad
    license udi pid CISCO2921/K9 sn FHK1407F25D
    license accept end user agreement
    license boot c2900 technology-package uck9
    hw-module pvdm 0/0
    hw-module sm 1
    username mtlops privilege 15 secret 5 $1$0qqx$1WGdfRW.flJrwmY7k8eUy0
    redundancy
    interface Embedded-Service-Engine0/0
     no ip address
     shutdown
    interface GigabitEthernet0/0
     ip address 10.118.0.10 255.255.255.0
     duplex auto
     speed auto
    interface GigabitEthernet0/1
     no ip address
     shutdown
     duplex auto
     speed auto
    interface GigabitEthernet0/2
     no ip address
     shutdown
     duplex auto
     speed auto
    interface SM1/0
     no ip address
     shutdown
     service-module fail-open
    interface SM1/1
     no ip address
    interface Vlan1
     no ip address
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    ip route 0.0.0.0 0.0.0.0 10.118.0.1
    control-plane
    mgcp behavior rsip-range tgcp-only
    mgcp behavior comedia-role none
    mgcp behavior comedia-check-media-src disable
    mgcp behavior comedia-sdp-force disable
    mgcp profile default
    dspfarm profile 1 conference
     codec g711ulaw
     codec g711alaw
     codec g729ar8
     codec g729abr8
     codec g729r8
     codec g729br8
     maximum sessions 7
     associate application SCCP
     shutdown
    gatekeeper
     shutdown
    telephony-service
     max-conferences 8 gain -6
     transfer-system full-consult
     fac standard
    line con 0
    line aux 0
    line 2
     no activation-character
     no exec
     transport preferred none
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
     stopbits 1
    line 67
     no activation-character
     no exec
     transport preferred none
     transport input all
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
     stopbits 1
    line vty 0 4
     transport input all
    scheduler allocate 20000 1000
    end
    CME-SIP-Phone#sh telephony-service fac
      telephony-service fac standard
        callfwd all **1
        callfwd cancel **2
        pickup local **3
        pickup group **4
        pickup direct **5
        park **6
        dnd **7
        redial **8
        voicemail **9
        ephone-hunt join *3
        ephone-hunt cancel #3
        ephone-hunt hlog *4
        ephone-hunt hlog-phone *5
        trnsfvm *6
        dpark-retrieval *0
        cancel call waiting *1

    VPN is not Configured prints on all phones now with the built-in VPN client if VPN isn't configured.  That's normal and is just cosmetic.  That should not be causing your registration issues.

  • Fire Wire NOT Working

    I have a Mac G5 2.5 For years I have had an M Audio interface connected to the Fire Wire port in the back; it worked consistently. I disconnected the M Audio last night in order to connect my video camera into the Fire Wire port (to import videos into iMovie) However, the computer would not detect the camera. Then I tried the Fire Wire port on the front of the computer, and still the computer would not recognize the camera. I gave up on trying to connect the video camera, disconnected it from the Fire Wire port, then plugged back in the M Audio. But now the M Audio will not work either! I tried both Fire Wire ports, AND I even tried another M Audio Fire Wire 410 just to make sure there was nothing wrong with the first one. I know there is power coming from the Fire Wire ports because the light on the M Audio will flicker, but the computer will not recognize it to allow me to use it the device. I also connected a Fire Wire hard drive - same thing.....the light goes on but the computer does not see the hard drive.
    At this point I have to assume that there is something wrong with the Fire Wire ports, as all 4 of my devices would not work. I have worked for years this way with minimal problems. What can I do?

    Hi rolesh79,
    I have read that it is not too difficult to burn out the firewire controller on the logic board. Especially, when the device is turned on when plugged in to the mac.
    You might try a third party firewire pci card as a replacement. A repair of disk permissions may have an effect. Or try a 800 to 400 adapter: http://www.pcconnection.com/IPA/Shop/Product/Detail.htm?sku=461273&oext=1038A&cisrc=14110944&cisku=461273.
    Regards

  • "Validation" enabled for the composite and my testsuites are not working

    I have posted the below issue in Test suite in JDEV - Studio Edition Version 11.1.1.2.0 But I felt that this is the right forum, so posting this again here:
    I have mediator calling bpel. Mediator is exposed as web service. Whenever I run the service using "Test" button on EM with validation turned on
    then it works and the process will be completed.
    But I have initiate xml in the test suites. I select "UnitTests" and select my test case xml that was associated to "Initiate Message for operation",
    I see that the process is still in the "Running" state. I put in exactly the same values as I use for testing the service from EM.
    Did anybody face this issue? This happens only when we turn the validation to "Enabled" in EM.
    I have "Validation" enabled for the composite and my testsuites are not working. When I test using unit tests, I am only seeing "Running" status of the processes and these are not getting completed.

    Hello there, RevDebMN.
    The following Knowledge Base article is always a great fallback article for troubleshooting Mail issues:
    OS X Mail: Troubleshooting sending and receiving email messages
    http://support.apple.com/kb/ts3276
    Particularly useful, in your case:
    Mail Connection Doctor shows one or more red dots () in the account Status column
    Check your Incoming IMAP or POP and Outgoing SMTP email account settings
    Use Apple's online Mail Setup Assistant to discover what the correct settings should be for both your Incoming (IMAP or POP) and Outgoing SMTP email servers. If your email service provider is not listed in the Mail Setup Assistant, visit your email service provider's website or contact their support staff to get the correct settings. You can use this "cheat sheet" when asking your email service provider about the settings you need.
    After you have the correct email service provider settings, make sure Mail is configured properly.
    Click here if your Incoming and Outgoing email account settings are correct, but the issue persists
    What alert message is shown in the Mail Connection Doctor "Details" column affected account?
    Click here if a "Could not connect to this (server type) server…" message appears
    Click here if a "Trying to log in to this (email server provider name) account failed…" message or any other error message appears
    If the issue persists, then you'll want to remove the account and then add it again using this article:
    Mail (Mountain Lion): Remove accounts
    http://support.apple.com/kb/PH11794
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • Multi Level BOm is not working in SAP afs

    Hi Experts,
             I am facing issue in MRP.For multi level bom's ,Requirements is not getting generates.Is there any settings is there to active multi level bom for afs materials.
    please suggest solution
    Thanks and Regards,
    Deepika.

    Hello Deepika,
    As we know AFS materials are planned at SKU level (Grid and stock categories)  you can use AFS MRP (/N/AFS/MD02) only.
    Please refer OSS note Note 981747 - FAQ - AFS Production Planning
    Question 5 Made-To-Order Planning -Multi-Level (MD50) does not work for AFS Materials and Sales Orders containing AFS materials.
    Answer: Made to Order Multi level planning functionality was never enhanced for AFS and hence transaction MD50 is not supported.
    Steps are as,
    1. Create a MTO/PTO sales order for an AFS material.
    2. Run AFS MRP using transaction code /AFS/MD02.
    3. Convert the planned order to production order.
    Best Regards,
    R.Brahmankar

Maybe you are looking for