HandleCrystalEvent failed

I am able to preview all of my reports in the CMC when you hit preview, But when I try to refesh any of my reports I am getting this error:
CrystalReportViewer
handleCrystalEvent failed
Unable to retrieve Object.
The database logon information for this report is either incomplete or incorrect.
I know that having parameters is not the issue, because I have some reports that do not have any.
I am using Microsoft SQL master database as my data source.
I also not able to schedule any of them.
Thanks

Tony thanks for the post. It did not fix my issue however it did get me thinking in a different direction on fixes. Still working on this issue.
>
Tony Foster wrote:
> After changing the datasource in the designer, did you republish the report? It may be a worthy try to remove the report from the repository and republish.
>
I did republish the report Also I have deleted and redid the report over from scratch still same results. What gets me is it works fine on CR designer but InfoView tanks everytime.
>
Tony Foster wrote:
>
> Or, in infoview under the reports properties, attempt to supply the data conection information manually, rather than to what is set in the report.
>
I did not see a place in InfoView or Central Management Console to change data source. The is a checkbox Refresh Options for Defaut Database Logon Information. I also have Use Object Repository when Refreshing Reports.
I am not sure but I do believe I deleted all of the business view info as well and redid that from scratch.

Similar Messages

Exporting Crystal Report to Excel Data Only Fails On Demand in Infoview

I am having the following problem with only 1 report in Business Objects. The report runs fine in Infoview, but the Excel export fails after around 5 minutes. It exports fine when scheduled. The reports is over 3,000 pages of data and comes in at around 45MB. It will export up to 2500 pages fine on demand. But this whole report used to run and export on demand perfectly. Perhaps only a few hundred records were added recently but that is all. I don't know of any other changes to the system.
The error says: CrystalReportViewer
                               handleCrystalEvent failed
                        Unable to retrieve Object
                        The Page Server you are trying to connect to is not accessible. Please contact your system administrator
Again, this is the only report this happens on. I've searched everywhere on the Internet without a solution.
Page Server settings: 60 and 120 minutes Unlimited records
Cache Server settings: 1000000 Kbytes; 80 minutes; it sees the page server in Metrics
If any more settings would help to diagnose the problem, please let me know. Thanks for the help.

How many number of rows are there in the report?
-Rahul

Export to Word RTF - Page Server error when over 160 pages exported

We have XIR2 SP2
We have a Crystal report published into this Enterprise which, when all parameters are widened, runs to 190 pages.
The resultant report includes tables
We can export to PDF but the client requires it in Word RTF
We can export to Word RTF Editable - and all 190 pages are produced in the resulting file, but of course the tables are omitted and the result is messy.
So, we need to export to Word RTF where the format is neat and includes the tables.
However, when we try and export more than 160 pages to Word RTF, we receive the following error.
CrystalReportViewer
handleCrystalEvent failed
Unable to retrieve Object.
The Page Server you are trying to connect to is not accessible. Please contact your system administrator.
We have a duplicate environment with an identical configuration, standing by as a failover environment and which points to the same data.This produces the same error, so we don't think it's an installation corruption or failure.
The page server is set to a maximum of 2,000,000 rows, the cache server at 256000 maximum.

Hi Tony F,
Many thanks for coming back on this one. Both Enterprise servers are identical in BO config, Windows 2003 server, but different in hardware.
One has 4 proc and one has 2, one has twice the memory of the other, yet both fail at over 161 pages. Both have their boCMS db's on different servers, both derive the data from different servers.
IIS is the web server. The only common denominator is the actual installation software itself and the person who installed it (me).
On Friday, instead of running the reports in Enterprise/Preview or Infoview (both exhibit the problem) I switched from our default activeX to DHTML, and advanced DHTML. No improvement (Our report wouldn't work with Java, which we never use)
On the suggestion of the SAP/BO support girl, I then SCHEDULED the report for immediate running and chose WordRTF as the format. This works fine.
So on that evidence I suspect a software glitch that is specific to using Infoview to open the report rather than schedule it - the two processes must access the WordRTF translator in different ways.
I'm hoping there is a patch or hotfix that can solve it. Sadly, our users don't have the appetite for the few extra clicks to use the workaround so we're going to have to pursue it with BO unless the forum comes up with an answer - perhaps its something I didn't do properly on installation, or a CMC/CMS setting. We've got 2m row limit on the page server but the report's row count is nothing like that and, anyway, it works if scheduled.
I'm really grateful to you for taking the time to reply, I hope the above answers your question - if I had hair to pull out, I'd be doing just that!
Kind regards
Tony W

Error of "Not enough memory for operation" when exporting Crystal Report

Hi,
I am getting errors in Business Objects when I try to export a report from its native Crystal format to PDF (or Word). This is only happening in one of our many reports.
When I try to export within the Business Objects viewer (in Crystal format), then click the "Export this report" button, and select "Adobe Acrobat (PDF) as the File Format, click OK, I get the following error:
CrystalReportViewer
handleCrystalEvent failed
WebReporting.dll error '80004005'
Not enough memory for operation.
/InformationCentral/Viewers/crystal_viewer.asp, line 39
This also occurs if I try to export to PDF within the Crystal Report designer as well, but the error is a bit different:
"Failed to export report" then "Memory Full".
Strange one this is....

Hi Peter,
Could you try to minimize the records in the report by giving some additional conditions? May be like give the date range or select for few regions etc?
Try in such a way so that your report downloads less number of records.
Hope this helps.
Regards,
Rashmi

Bit locker drive encryption failed due to power failer and hard disk corrupted

I ran Bitlocker drive ecryption drive D. My pc is windows 7 ultimate, while it was in progress of 1% due to power failer the encryption failed, when power resume the drive didn't showed the file format nor the size but it shows the size in disk management.
It showed like this in My computer
I do Have the recovery code password and back of recovery password so I ran the "manage-bde-_unlock D:-rp[my code ]
and my pc got hang no other option rather than to press the restart button.
then I used commang "repair-bde -force D:I:-rp[my rp] and following info showed but it stucked in 1% about 8 hours, and there was no increase in the pecentage
I also connected the hardisk to mac but all othe partation showed but didn't showed the encrypted one.
I had lots of memorable picture and other backups so any one kindly help me to get out of this problem. Thanks for help

Hi,
The BitLocker encryption and decryption processes can be interrupted by turning the computer off, and it will resume where it left off the next time Windows starts. This is true even if the power is suddenly unavailable.
Bitlocker-repair (repair-bde) tool
can't repair a drive that failed during the encryption or decryption process.
In addition, could you please explain a bit for what drive you are trying to deal with? external one?
When you first restart your PC, have you seen any signs that indicate that the encryption is in process?
Regarding your scenario, please take a look to see if the following articles could help here:
Scenario 11: Recovering Data Protected by BitLocker Drive Encryption (Windows 7)
Besides, when running manage-bde command, did we followed the steps mentioned in the below article?
Scenario 14: Using a Data Recovery Agent to Recover BitLocker-Protected Drives (Windows 7)
Best regards
Michael Shao
TechNet Community Support

Cannot send email from my Touch (connection to smtp server fails)

Hello,
I have a new iPod Touch with 1.1.4 and the January apps. I am having a problem setting the Mail application.
I am trying to connect to the IMAP/SMTP servers at my university. I am using the exact same settings and passwords I use on my laptop, which works fine. I can receive email fine on my Touch, but every time I try to send one it fails tellings me "the connection to the outgoing server smtp.myuniversity.edu failed".
If I on purpose write a wrong password for the outgoing mail, the error message I get is different ("check the account settings for the outgoing server smtp.myuniversity.edu").
The university IT people confirmed my settings, and told me that there is nothing blocking any handheld device from using the server.
Does anyone know why this would happen?
Thanks,
Marcelo

Thank you very much for your responses
1) the link to mail setup is (sorry, it's quite long)
http://www.knowledgepak.com/kpaksonline/kpol.asp?PiAlias=kpolpi17&k2dockey=04096 3251575739@kpol17&ViewLink=true&SkipHeader=false&printformat=true
2) I am indeed using SSL, as instructed by IT
3) I do use port 587 instead of 25 (25 does not work either)
Any ideas? Thanks again.
MC

BSI ConnectToDataSet...failed

Hi
We have a problem with the BSI, we had been getting a dump "RFC_ERROR_SYSTEM_FAILURE", I followed the SAP Note 1068271 for the debug, and the result is:
=Thu Jan 22 11:53:37 2009
=SAP AG, Walldorf - Business API for BSI TaxFactory 8.0
=RfcAccept called
=Mapping ABAP RFC_PAYROLL_TAX_CALC_US_80 to C function srv_Payroll_Tax_Calc_US_80
=Mapping ABAP RFC_HR_TAXLOCATOR_US_80 to C function srv_hr_taxlocator_us_80
=Waiting for ABAP function calls
=Running function srv_Payroll_Tax_Calc_US_80
=Loading import parameters
=Loading export parameters
=Loading internal tables
=Calling Payroll_Tax_Calc_US
=Running Connect_DB_Payroll_Tax_Calc_US
BSI dataset -> 110
ConnectToDataSource...Succeeded
ConnectToDataSet...failed
Error String -> 7777 - [Oracle][ODBC][Ora]ORA-00933: SQL command not properly ended
=RFC error
operation/code Connect_DB_Payroll_Tax_Calc_US
key RFC_ERROR_SYSTEM_FAILURE
status
message See RFC trace file or SAP system log for more details
internal status
The RFC under sm59 is working fine, the error is on the connection to the Dataset according to the Debug log "ConnectToDataSet...failed".
I don't know what to check about the Dataset, could you please help me?
Best Regards

Yes, it's correct.
I checked it's 8.0.
I think is a problem with the parameters under tf80server.bat.
SET
TF80_CONNECT_STRING=DSN=;UID=;PW
D=;
SET TF80_SCHEMA_NAME=.TF80
REM for SAP trace debugging, uncomment below & see file
errors.txt in gateway working directory
REM C:\BSI\TAXFACTORY\tf80serverdebug.exe %*
REM else for usual operation
C:\BSI\TAXFACTORY\tf80server.exe %*
I don't know what is the "ODBC_DSN_NAME"
I have the user, password, the database name...
Best Regards

Installation of IPC AP 7.0 Jar is getting Failed when uploading in CRM

Hello Experts,
we did some changes in the previosly uploded version of IPC AP 7.0 customer user exit Jar file in eclipse.
While uploading the new modified jar through transaction /SAPCND/UE_DEV in CRM we are getting error :" installation of module <Jar file name > has failed ".
when we checked the logs in SM 53 we seen the below mentioned error:
Message: Exception of type com.sap.sql.log.OpenSQLException caught: Exception of type com.sap.sql.sqlparser.CommonSQLParserException: - statement "DELETE FROM "SVMCRT_MOD_TR_T" WHERE "MODULE_NAME" LIKE ? ESCAPE ^ (reason: Modification of ABAP tables is not permit ted)" is not supported
caught: - statement "DELETE FROM "SVMCRT_MOD_TR_T" WHERE "MODULE_NAME" LIKE ? ESCAPE ^ (reason: Modification of ABAP tables is not permitted)" is not supported
--> com.sap.sql.log.OpenSQLException: Exception of type com.sap.sql.sqlparser.CommonSQLParserException: - statement "DELETE FROM "SVMCRT_MOD_TR_T" WHERE "MODULE_NAME" LIKE ? ESCAPE '^' (reason: Modification of ABAP tables is n" is not suppor ted
caught: - statement "DELETE FROM "SVMCRT_MOD_TR_T" WHERE "MODULE_NAME" LIKE ? ESCAPE '^' (reason: Modification of ABAP tables is not permitted)" is not supported
at com.sap.sql.log.Syslog.createAndLogOpenSQLException(Ljava/lang/Class;Ljava/lang/String;[Ljava/lang/Object;)Lcom/sap/sql/log/OpenSQLException;(Syslog.java:85)
at
if required i can post the complete stack trace.
any inputs/suggestions are most welcome.
Thanks & regards,
Siddharth

Hi Mark,
Yesterday after Posting the thread we found the same Note ,Issue occured because of JAVA write access was not enabled on the table ,After enabling it as mentioned in SAP Note, Jar file get successfully uploaded.
Thanks for your Help also.
Regards,
Siddharth

Upgrade to ERp6 phase STARTSAP_NBAS error: DDIC login fails

Hi
During an upgrade from 4.7 to ERP6 I get the following error
message in phase STARTSAP_NBAS:
SYSTEM START failed, code -2
-2: the test rfc did not work.
Try to log on to the system with user DDIC
When I try to log on to the system as user DDIC, I get the following
error message:
DB-Error -0
SAP* can log in .The password I submit is correct. I have not changed this password at
any time.
Any ideas are most welcome

Hi,
DB-Error -0 indicate problem with kernel, try to upgrade kernel.
check Note 760175 - 6.20: Logon not possible (after DB export or system copy)
regards,
kaushal

Running workbook from .bat fails to start application missing CORE40 dll

I have been running several workbook via windows task scheduler / vbscript &/or bat files.
I now have a new box which I access thru Remote Desktop Connection, so I can run all these automated updates without having my screen blinking everytime a shedule workbook starts.
If I click on the actual Discoverer icon, or the discoverer workbook shortuct, all works well.
If I click on the .bat file, or try to run the workbook via the cmd , it gives me the following error:
DIS4USR.EXE – Unable To Locate Component
“this application has failed to start because CORE40.DLL was not found. Re-installing the application may fix this problem.”
The dll is under c/orant/bin/core40.dll, which is where I've read it should be, and it works fine in my regular box...
Please help! URGENT :)
Thanks!

Hello
Check the PATH environment variables for the machine you are on and the one you are connecting to.
You might not have Discoverer's objects in the PATH.
Another possibility is that you have more than one piece of ORACLE software on the machine and you may need to also set the ORACLE_HOME within the BAT file.
Best wishes
Michael

Due to my laptop screen failing i have to return to facory settings, can i reinstall adobe reader and adobe air afterwards?

Due to my laptop screen failing I have to return it to factory settings, can I reinstall adobe reader and air afterwards?

I don't see why not. Do you foresee a special difficulty?

Downloads to documents folder fail due to parallel upload

Hi, mobile documents is a great tool that I use to replicate all business relevant documents to mobile clients. However there is one great disadvantage for me. When you download a file that is a bit larger (>1 MB), during the download the client will already start uploading the temporary file. So the download then fails as it cannot convert the temporary file into the final one.
This is something that does not happen for equivalent clients (for example skydrive). Do you think this is something that can be fixed?
thanks,
Heiko

Hi Heiko,
Let me explain again:
You said "uploader locks the file so that it can no longer be changed". For the temporary file it is the downloader which have locked the file. Hence, the impression that file is getting uploaded because it is locked is hence not correct.
The next version might be available in Q1\Q2 2014. We will keep everyone updated via community.
Best Regards,
Ashwani Kr Sharma

Jabber call to voice mail fails with fast busy over VPN

I have an issue that I ran into with CIPC phones over a VPN. If a CIPC phone called over a VPN and started ringing a phone the call would fail with fast busy at the time the call would be forwarded to voicemail. I found the issue was when remote the CIPC phone would negotiate the g.729 codec, when forwarded to a voicemail pilot over a SIP trunk set to g.711 the call would fail due to codec missmatch when no transcoders are present.
So now I am running into what I believe to be the same issue with Jabber, when on premise the calls to voice mail work just fine, but when remote they fail. I can directly call the voicemail pilot without error, but if calling a phone the call gets fast busy at the point we are forwarded to voicemail. Even though all my regions are set to talk to all other regions on G.711 and the voicemail SIP trunk is set to G.711, I believe with the new features in CUCM9 that a lower speed codec has been negotiated since the we are going over the VPN, or Jabber has done this as it knows it's over VPN (not sure). WIth CIPC I could go into the settings and turn off the Optimize for Bandwidth check box and the call would negotiate G.711. With Jabber I can't find anything that would tell my Jabber client to stay on G.711 and I can only imagine this is a codec missmatch as the following are true.
1. CIPC and Jabber share the same line
2. VPN established and CIPC optimised for low bandwidth un-checked
3. Over the same VPN the CIPC phone can leave a voicemail
4. Over the same VPN the Jabber client gets fast busy once forwarded to voicemail
5. Voicemail environment is Exchange-UM over SIP trunk
6. SIP trunk is assigned a Device Pool, that is assigned to a region that all other regions communicate G.711 to
7. On CIPC if optimised for low bandwidth is checked I get the exact same issue as I get with the Jabber client (fast busy when forwarded to voicemail)
Would anyone know what I can do in CUCM 9 to fix this issue, as said no issue when all devices are on premise. Wondering if there is a service parameter or a way to change the codec selection so the Jabber client attempts to always negotiate G.711. The correct answer would be to get some PVDM DSP resources and kick up a transcoder in my resource group, and that may be what I talk them into doing if I have no other options.

We have been getting the exact same thing for almost a year now... since switching to FiOS Digital Voice in May of last year! Every time I call in to report it they 'escalate' the issue but it never gets resolved. The problem seems to be in the initial connection. Most of the time it works fine but, several times a month, after I call to get messages and it starts to play the new message it goes dead and I get the busy signal. I get the same message when I call back: “I’m sorry – that account is in use at this time. Please try again later!” I have even called in with my cell phone and get the same message! I HAVE EVEN used the Internet to see if I could get my messages and, when I hit Play, I get a pop-up saying: “Your Voice Mail box is currently in being accessed; please try again later. If the problem continues, please contact our Customer Support Center at 1-888-553-1555. We apologize for any inconvenience.” This is obviously a software bug that Verizon has no clue on how to troubleshoot OR fix!!! I wonder how many people have the problem and just don’t bother reporting it because of the hassle? When it first started happening they destroyed my entire mailbox and I had to re-enter the complete mailbox setup again – 3 times!!! NEVER let them talk you into that!!! It’s their problem and they need to fix it!!!!!!! I wish I could go back to the ‘normal’ voicemail we originally had… they want hundred$ to switch back because I’d be breaking my #$@%^&* contract! Good luck if you have Verizon………

Gmail access fails on safari. But it works when i login as administrator. Please help!

I am unable to use gmail from a regular user account on my iMac.It fails with an error string that ends with "... becasue Safari can't establish a secure connection to the server "accounts.google.com". "
I have tried resetting safari and it does not help.
I have tried adding DNS entries based on some discussion board suggestions and that does not help either.
I am able to access gmail as an administator on the same machine though!
Please point me in the right direction, please! Thanks!

You may have to take the computer to the Apple store to have the computer checked out.
Dead line is tuesday?
1. Try an external USB keyboard.
2. This may help.
    http://support.apple.com/kb/PH10680
3. Virtual keyboard
    There is a virtual keyboard available in OS X 10.8.4
    System Preferences > Keyboard
    Checkmark the box beside "Show Keyboard & Character Viewrs in menu bar.
    Click "Input Sources" and then "Show input menu in menu bar".
Best.

SSL VPN, "Login failed" and "WebVPN: error creating WebVPN session!"

Hi,
Just ran the wizard for Anyconnect SSL VPN, created a tunnel group, a vpn pool and added user to it. When trying to logon on the SSL service, it simply says "login failed". I suspect that the user might not be in correct groups or so?
some relevant config
webvpn
enable wan
svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1
svc enable
group-policy vpnpolicy1 internal
group-policy vpnpolicy1 attributes
vpn-tunnel-protocol svc
tunnel-group admins type remote-access
tunnel-group admins general-attributes
address-pool sslpool2
default-group-policy vpnpolicy1
username myuser password 1234567890 encrypted privilege 15
username myuser attributes
vpn-group-policy vpnpolicy1
Debug:
asa01# debug webvpn 255
INFO: debug webvpn enabled at level 255.
asa01# webvpn_allocate_auth_struct: net_handle = CD5734D0
webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
webvpn_portal.c:webvpn_login_validate_net_handle[2234]
webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
webvpn_portal.c:webvpn_login_assign_app_next[2272]
webvpn_portal.c:webvpn_login_cookie_check[2289]
webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name =
webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
webvpn_login_resolve_tunnel_group: tgCookie = NULL
webvpn_login_resolve_tunnel_group: tunnel group name from default
webvpn_login_resolve_tunnel_group: TG_BUFFER = DefaultWEBVPNGroup
webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
webvpn_portal.c:webvpn_login_check_cert_status[2733]
webvpn_portal.c:webvpn_login_cert_only[2774]
webvpn_portal.c:webvpn_login_primary_username[2796]
webvpn_portal.c:webvpn_login_primary_password[2878]
webvpn_portal.c:webvpn_login_secondary_username[2910]
webvpn_portal.c:webvpn_login_secondary_password[2988]
webvpn_portal.c:webvpn_login_extra_password[3021]
webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 4
webvpn_portal.c:webvpn_login_aaa_not_resuming[3137]
webvpn_portal.c:http_webvpn_kill_cookie[790]
webvpn_auth.c:http_webvpn_pre_authentication[2321]
WebVPN: calling AAA with ewsContext (-867034168) and nh (-849922864)!
webvpn_add_auth_handle: auth_handle = 17
WebVPN: started user authentication...
webvpn_auth.c:webvpn_aaa_callback[5138]
WebVPN: AAA status = (ACCEPT)
webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
webvpn_portal.c:webvpn_login_validate_net_handle[2234]
webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
webvpn_portal.c:webvpn_login_assign_app_next[2272]
webvpn_portal.c:webvpn_login_cookie_check[2289]
webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name =
webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
webvpn_portal.c:webvpn_login_check_cert_status[2733]
webvpn_portal.c:webvpn_login_cert_only[2774]
webvpn_portal.c:webvpn_login_primary_username[2796]
webvpn_portal.c:webvpn_login_primary_password[2878]
webvpn_portal.c:webvpn_login_secondary_username[2910]
webvpn_portal.c:webvpn_login_secondary_password[2988]
webvpn_portal.c:webvpn_login_extra_password[3021]
webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 4
webvpn_portal.c:webvpn_login_aaa_resuming[3093]
webvpn_auth.c:http_webvpn_post_authentication[1485]
WebVPN: user: (myuser) authenticated.
webvpn_auth.c:http_webvpn_auth_accept[2938]
webvpn_session.c:http_webvpn_create_session[184]
WebVPN: error creating WebVPN session!
webvpn_remove_auth_handle: auth_handle = 17
webvpn_free_auth_struct: net_handle = CD5734D0
webvpn_allocate_auth_struct: net_handle = CD5734D0
webvpn_free_auth_struct: net_handle = CD5734D0

AnyConnect says:
"The secure gateway has rejected the agents VPN connect or reconnect request. A new connection requires re-authentication and must be started manually. Please contact your network administrator if this problem persists.
The following message was received from the secure gateway: Host or network is 0"
Other resources indicate that it's either the tunnel group, or the address pool.. The address pool is:
ip local pool sslpool2 172.16.20.0-172.16.20.254 mask 255.255.255.0
asa01# debug webvpn 255
INFO: debug webvpn enabled at level 255.
asa01# debug http 255
debug http enabled at level 255.
asa01# webvpn_allocate_auth_struct: net_handle = CE9C3208
webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
webvpn_portal.c:webvpn_login_validate_net_handle[2234]
webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
webvpn_portal.c:webvpn_login_assign_app_next[2272]
webvpn_portal.c:webvpn_login_cookie_check[2289]
webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name =
webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
webvpn_login_resolve_tunnel_group: tgCookie = NULL
webvpn_login_resolve_tunnel_group: tunnel group name from default
webvpn_login_resolve_tunnel_group: TG_BUFFER = DefaultWEBVPNGroup
webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
webvpn_portal.c:webvpn_login_check_cert_status[2733]
webvpn_portal.c:webvpn_login_cert_only[2774]
webvpn_portal.c:webvpn_login_primary_username[2796]
webvpn_portal.c:webvpn_login_primary_password[2878]
webvpn_portal.c:webvpn_login_secondary_username[2910]
webvpn_portal.c:webvpn_login_secondary_password[2988]
webvpn_portal.c:webvpn_login_extra_password[3021]
webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 4
webvpn_portal.c:webvpn_login_aaa_not_resuming[3137]
webvpn_portal.c:http_webvpn_kill_cookie[790]
webvpn_auth.c:http_webvpn_pre_authentication[2321]
WebVPN: calling AAA with ewsContext (-845538720) and nh (-828624376)!
webvpn_add_auth_handle: auth_handle = 22
WebVPN: started user authentication...
webvpn_auth.c:webvpn_aaa_callback[5138]
WebVPN: AAA status = (ACCEPT)
webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
webvpn_portal.c:webvpn_login_validate_net_handle[2234]
webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
webvpn_portal.c:webvpn_login_assign_app_next[2272]
webvpn_portal.c:webvpn_login_cookie_check[2289]
webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name =
webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
webvpn_portal.c:webvpn_login_check_cert_status[2733]
webvpn_portal.c:webvpn_login_cert_only[2774]
webvpn_portal.c:webvpn_login_primary_username[2796]
webvpn_portal.c:webvpn_login_primary_password[2878]
webvpn_portal.c:webvpn_login_secondary_username[2910]
webvpn_portal.c:webvpn_login_secondary_password[2988]
webvpn_portal.c:webvpn_login_extra_password[3021]
webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 4
webvpn_portal.c:webvpn_login_aaa_resuming[3093]
webvpn_auth.c:http_webvpn_post_authentication[1485]
WebVPN: user: (myuser) authenticated.
webvpn_auth.c:http_webvpn_auth_accept[2938]
HTTP: net_handle->standalone_client [0]
webvpn_session.c:http_webvpn_create_session[184]
webvpn_session.c:http_webvpn_find_session[159]
WebVPN session created!
webvpn_session.c:http_webvpn_find_session[159]
webvpn_remove_auth_handle: auth_handle = 22
webvpn_portal.c:ewaFormServe_webvpn_cookie[1805]
webvpn_free_auth_struct: net_handle = CE9C3208
webvpn_allocate_auth_struct: net_handle = CE9C3208
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE9C3208
webvpn_allocate_auth_struct: net_handle = CE9C3208
webvpn_auth.c:webvpn_auth[581]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
WebVPN: session has been authenticated.
webvpn_free_auth_struct: net_handle = CE9C3208
webvpn_allocate_auth_struct: net_handle = CE9C3208
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE9C3208
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_allocate_auth_struct: net_handle = CE9C3208
webvpn_auth.c:webvpn_auth[581]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
WebVPN: session has been authenticated.
webvpn_free_auth_struct: net_handle = CE9C3208
webvpn_allocate_auth_struct: net_handle = CE9C3208
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE9C3208
webvpn_allocate_auth_struct: net_handle = CE863DE8
webvpn_auth.c:webvpn_auth[581]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
WebVPN: session has been authenticated.
webvpn_free_auth_struct: net_handle = CE863DE8
webvpn_allocate_auth_struct: net_handle = CE863DE8
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE863DE8
webvpn_allocate_auth_struct: net_handle = CE9C32C8
webvpn_auth.c:webvpn_auth[581]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
WebVPN: session has been authenticated.
webvpn_free_auth_struct: net_handle = CE9C32C8
webvpn_allocate_auth_struct: net_handle = CE9C32C8
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE9C32C8
webvpn_allocate_auth_struct: net_handle = CE9C32C8
webvpn_allocate_auth_struct: net_handle = CE863DE8
webvpn_auth.c:webvpn_auth[581]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
WebVPN: session has been authenticated.
webvpn_auth.c:webvpn_auth[581]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
WebVPN: session has been authenticated.
webvpn_free_auth_struct: net_handle = CE863DE8
webvpn_allocate_auth_struct: net_handle = CE863DE8
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE863DE8
webvpn_free_auth_struct: net_handle = CE9C32C8
webvpn_allocate_auth_struct: net_handle = CE9C32C8
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE9C32C8
webvpn_allocate_auth_struct: net_handle = CE9C32C8
webvpn_auth.c:webvpn_auth[581]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
WebVPN: session has been authenticated.
webvpn_free_auth_struct: net_handle = CE9C32C8
webvpn_allocate_auth_struct: net_handle = CE9C32C8
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE9C32C8
HTTP: Periodic admin session check (idle-timeout = 1200, session-timeout = 0)
webvpn_allocate_auth_struct: net_handle = CE9C32C8
webvpn_auth.c:webvpn_auth[581]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
WebVPN: session has been authenticated.
webvpn_free_auth_struct: net_handle = CE9C32C8
webvpn_allocate_auth_struct: net_handle = CE9C32C8
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE9C32C8
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_allocate_auth_struct: net_handle = CE9C32C8
webvpn_auth.c:webvpn_auth[581]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
WebVPN: session has been authenticated.
webvpn_free_auth_struct: net_handle = CE9C32C8
webvpn_allocate_auth_struct: net_handle = CE9C32C8
ewsStringSearch: no buffer
Close 0
webvpn_free_auth_struct: net_handle = CE9C32C8
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_find_session[159]
webvpn_allocate_auth_struct: net_handle = CC894AA8
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:webvpn_update_idle_time[1463]
Close 1043041832
webvpn_free_auth_struct: net_handle = CC894AA8

HandleCrystalEvent failed

Similar Messages

Maybe you are looking for