Hard crash now hard drive not recognized in disk utility.

During a virus scan the Macbook froze up now the computer does not seem to be accessing the hard drive. Tried to reinstall Leopard but the internal hard drive is not recognized (same is true when we tried to use Disk Utility). It will not start in safe mode either. Does this sound like a fried hard drive or maybe a corrupted drive that might be repairable with DiskWarrior? Any thoughts would be appreciated.

If the A/V you were using was Norton/Symantec, the drive may be OK. Norton is a virus.
Burn a Ununtu CD and see if you can boot into it and look at the drive before giving up on it.

Similar Messages

  • Hard drive not recognized in disk utility

    I'm trying to replace the hard drive in my MacBook Pro , the old hard drive was not recognized in disk utilities after the computer crashed .After installing a new hard drive and booting from the original Mac OS install DVD,( leopard?) the new hard drive is not recognized either ? Help

    It may be the internal connecting cable that is the problem.  If you can install the new HDD in an enclosure, connect it to the MBP, then see if you recognize it using the OSX installation disk.  If so, the internal connector should be replaced.
    Ciao.

  • Airport extreme hosted hard drive not recognized by Disk Utility

    Hi, all.  I've had success for a month now hosting a 4T hardrive wirelessly via my Airport Extreme.  I use it for Time Machine backups and remote storage.  So I'd like to repartition that hardrive via Disk Utlity, however Disk Utility no longer recognizes the 4T hardrive hosted via my Airport Extreme.  How can I get my Airport Extreme external drive to show up in Disk Utility so I can format it again?

    I'm not sure you're aware but I wanted to let you know that using an external drive connected to the Airport USB port as a Time Machine backup device isn't supported/recommended by Apple. don't be surprised if you think it's working and you go to use it to restore from a crash, and you can't.  Just a warning.

  • Replacement hard drive not shown in Disk Utility

    So I just finished installing a replacement hard drive for my PB 12". I got a Seagate 2.5" ATA Momentus 5400 etc as per my previous thread. But after firing it up from the install disk, the new volume fails to show up. Anyone else had this problem? And fixed it? Opening up the case again now...

    Don't know if your problem solved. Had the same thing happen to me. Was told that new HD was bad (unlikely), Logic board was bad (disaster). Then finally was tole by another tech (OWC) that it sounded like a bad cable connection. Took it apart again and reseated both ends of HD cable a couple of times. Started up and the HD recognized by disk utility. Works great since. Hope your problem as simple as mine.

  • External hard drive not showing in disk utility

    my samsung external hard drive has always worked with no problem on my mac..
    I have just plugged it in to do some work and it will not appear anywhere..
    not even in disk utility
    i have tried the USB port and it is working fine because i also have a mouse and that worked fine in that port..
    PLEASE SOMEONE HELP ME!

    Try following tips.
    USB and FireWire Quick Assist - Apple Support

  • Xserve Raid not recognized by Disk Utility

    My Xserve Raid is recognized when I run the RaidAdmin utility. I can create new arrays everything shows up without any problems. I updated the firmware for the Xserve Raid using just the ethernet connection to administer it. Changed the card and the cables that are used to connect the Raid server to a G5 server, but it still does not get recognized by Disk Utility. I am at a loss of what to do next. I have green lights for everything....no problems showing up in RaidAdmin. Please, please help....

    Hello
    I have the exact same problem: after updating java and rebooting the server, the raid array is no longer visible. Everything is green, no errors in the log files, fibre channel is up and running, BUT: the array does not show with any SCSI address. LUN masking is off. Server is at 10.5.8 (intel). The array was mounting just fine before the reboot (and all before that). I've plugged the fibre channel into a PPC server, same thing: link ok, no SCSI. I'm reconditioning the drive at the moment, but it should still be visible.
    Any help greatly appreciated.

  • Hard drive not appearing in disk utility

    My hard drive on my MacBook crashed and I purchased a new one.
    I attempted to install the Mac OSX on the new hard drive, but have run into a couple issues.
    First issue I ran into was that I found out I had the wrong Install DVDs. I was able to format the hard drive with these disks so I got to step one successfully anyway.
    I then did find the correct Install DVDs, but now the Hard Drive doesn't show up in Disk Utility.
    Any ideas how I can locate the hard drive?
    (Sorry, but I can't obtain the info about the MacBook through the Installer (greyed out). It was purchased around 2007 or 2008. The Install DVDs have 2007 on them.)

    Create a data recovery, undelete boot drive
    dustysjuls wrote:
    Will that erase all of the files on my hard drive? Or will it just erase and reinstall the operating system? I do not have my files backed up.
    A #18 Reinstall Just OS X, details here:
    Step by Step to fix your Mac

  • External hard drive not visible in disk utility or finder

    Hi all,
    I have had a good look through previous discussions and I can't seem to find an issue relevant to mine.
    My external hard drive has 2 partitions (1 time machine back up, 1 general hard drive). The issue is that the HD is running when it is plugged in however it is not visible in either disk utility or finder.
    I am running OS X 10.10 (Yosemite) on a 2010 MacBook Pro. I also have parallels desktop running windows 7. When I boot windows and plug in the HD I usually get the option to mount the HD to either OS X or Windows. With this issue the option window appears for a split second (not enough time to select either) and then disappears. It seems that the HD may be ejecting itself as soon as it is registered by the computer. I have tried using a different power cable for the HD and also a different usb cable, this doesn't help.
    The external HD is a Samsung D3 Station, which i have had for 6 months now and never had an issue with.
    Any help is appreciated
    Thanks,
    Bruce

    An update for anyone who can help me:
    I have tried the external hard drive in other computers (mac and windows), each time I get the same problem above.
    I have removed the HD from the enclosure and purchased a docking station for it (3.5" SATA). When I plug it in to the laptop it disconnects itself straight away before it is visible. With the windows computers it installs the drivers and says that the device is ready to use, then disconnects before it shows up.
    As the HD is not visible there is no option to re-format or anything.
    This is very frustrating as I was using the HD with no issues and it randomly disconnected and I have not been able to access since.
    Thanks in advance for any help.
    Bruce

  • External hard drives not showing in disk utility

    When I connect a new Eagle/Consus W-Series external hard drive enclosure to my 15" PB, the hard drive doesn't show-up in the left hand pane of the Disk Utility window. The only thing that shows is the drive in the PB. The hard drive in the enclosure is a WD SATA and is connected via USB cable. The same thing happens, or doesn't happen, when I'm connected via ethernet to my G5 2.3GHz Dual Core: when I open Disk Utility on the PB, the drive on the G5 doesn't show. What I'm trying to attempt is to mirror/clone Tiger from my PB onto the new, to me, G5 using SuperDuper.

    Hi, Bob. I obviously didn't understand the situation properly, and now that I realize that, I'm afraid I still don't.
    When the G5 is connected, via ethernet to my PB, the hard drive does not show-up in the PB's disk utility pane.
    The G5 doesn't have a hard drive in it now, is that correct? So why connect it via Ethernet to the Powerbook?
    If you're trying to clone the Powerbook's hard drive onto the G5's drive inside the external enclosure, all that needs to be connected is the external enclosure to the Powerbook, via USB cable. The G5 itself isn't involved in that process at all. When the G5's drive is in the enclosure and connected to the Powerbook, does it appear in Disk Utility on the Powerbook? If not, see my previous suggestions, with the exception of my comment about it not working with either computer.
    If the SATA hard drive doesn't appear on the Powerbook's desktop or in Disk Utility when it is in the G5 and the computers are properly networked via Ethernet, recheck your sharing settings: the G5's drive must be shared to be visible to the Powerbook. In that mode, you may not be able to clone the Powerbook's drive to the other one, because the drive in the G5 is being used to run the G5. But if the G5's drive is partitioned, you should be able to clone the Powerbook's drive, via Ethernet, to a partition other than the one which contains the OS that's running the G5.
    While the hard drive is in the external enclosure, I can hear it spinning, and am assuming that all the connections are working properly.
    If the drive spins, you can be sure it's getting power, and that's good. But you can't safely conclude from that that any or all of the data connections are working properly; in fact the evidence suggests the contrary.
    In short, there may be not one but two problems at work here: incorrect sharing settings when the two computers are networked, and a bad cable, connection, or enclosure when the drive is connected to the Powerbook via USB.
    EDIT: Let me also add that if the only Tiger installer discs you have are the ones that came with the Powerbook, then having copies of that Tiger installation on both of your computers would be a violation of the software license that accompanied those discs, which entitles you to have Tiger installed on only one computer at a time. If that's the case, you should really buy a retail Tiger installer disc to use on the G5.
    Message was edited by: eww

  • Hard drive not found in Disk Utility

    Hello there. I wonder if anyone would be so kind to assist.
    Bought a second hand Macbook. Had 80gb and worked fine on Leopard. Bought a new 320gb SATA, replacing the 80gb.
    I have a Leopard upgrade disc and a Tiger full install 2-disc set. I insert Tiger and the Macbook advises that I am unable to install this software on to this hard drive. As the hard drive wasnt MAC formatted I guess I need to that first> I enter Disk Utility but cannot see my new HD (only the DVD drive where Tiger is at).
    Any ideas?

    Drive is SATA II. No jumper settings as I had already checked.
    Have eventually got round this very tedious problem. 320gb was not recognisable at all as you well know. Attached it to a caddy and used a Macbook Pro to see it. Couldn't find it. I attached it to a Windows machine and it got recognised. Re-attached it to the Macbook Pro (which now recognised it) and I formatted the 320gb into GUID format. The original 80gb which still worked had Leopard on it. I put that back into the Macbook and attached the 320gb externally via a USB caddy. Inserted Leopard DVD disc followed instructions and I let it restart. On restart it asks me the location of where to install and I chose the partition I created on the 320gb. Leopard was installed externally.
    Reattached the 320gb back onto my Macbook and it worked. 6hrs of frustration but I got there in the end.
    If anyone needs to remove the L-shaped panel from the battery bay from a Macbook I can do it free of charge. I can do that job blindfolded!

  • Hard Drive not showing in Disk Utility (but showing fine on PC)

    I have been using an 1TB USB powered Hard Drive with my MBP for a year or so.
    I got a new 2 TB drive and loaded it and installed the seagate dashboard software.
    At that point, it appears something may have happened to my HP and it no longer appears on my Mac or in Disk Utility.  It appears to be getting power, and it shows up fine on a Windows PC.
    Any thoughts??
    This one is really baffling me?
    Thanks

    One other note
    A folder called TheVoumeSettingsFolder now appears on the HP, in case that is causing the issue.
    Thanks

  • Iomega external hard drive not appearing in Disk Utility

    I have a MacBook Pro (from 2011) and I'm running OS X 10.9.5. I have an old Iomega external hard drive. I'm not certain but this thing might be about 3-4 years old? When I connect the drive to my MBP, it shows up in Finder under Devices. But what appears is the Windows disk utility that is pre-loaded on the drive. The actual drive does not appear and I can't move files onto it in Finder.
    When I go into Disk Utility and try to format the drive for Mac use, it doesn't appear.
    Is there anything I can do or am I stuck with this old drive that doesn't work with Macs?

    Try following tips.
    USB and FireWire Quick Assist - Apple Support

  • New internal hard drive not seen in disk utility

    Hi
    I replaced my hard drive with a western digital black edition but when I use it as an internal it is not seen by the disk utility. 
    I have installed and booked from the new drive using USB so it doesn't seem faulty. 
    When I use the old drive as an internal it works so I don't know what's going wrong. 
    I have had a look at similar problems but nothing I have tried has helped. 

    It may be the internal connecting cable that is the problem.  If you can install the new HDD in an enclosure, connect it to the MBP, then see if you recognize it using the OSX installation disk.  If so, the internal connector should be replaced.
    Ciao.

  • Hard drive not showing in Disk Utility?

    Recently, I went to install Windows 10 via Bootcamp and set up two partitions (one for OS X, 500gb and one for Windows, 500gb). I accidentally installed Windows onto of the OS X partition and somehow the Windows OS disappeared so I currently have no OS to boot in to. I can run Yosemite off of a USB, but when I go to Internet Recovery or Disk Utility, it only shows this.
      Disk Description : Media 
      Total Capacity : 0 Bytes
      Connection Bus : SATA 
      Write Status : Read/Write
      Connection Type : Internal 
      S.M.A.R.T. Status : Not Supported
      Partition Map Scheme : Unformatted
    I know the hard drive can't be dead because this is a brand new laptop and it was working just fine before. How can I get the drive fixed?
    Instead of buying DiskWarrior since it's $110, can I just buy a new 1TB HDD and put it into the computer? Can I hook up my laptop via Firewire to my iMac and reformat the drive or something?

    OGELTHORPE wrote:
    Or try and boot the MBP with the OPTION + COMMAND + R keys.  The display should show a revolving globe.  By following the instructions, this will connect the MBP to the Apple servers and allow you to erase the HDD and reinstall the ORIGINAL OSX.
    Ciao.
    The problem with this option is that the computer does not recognize that there is any space on the hard drive itself. The hard drive is just labeled as "Media" and has 0 bytes available. I tried using GUID partitions but Disk Utility says the drive is too small.

  • External hard drive not seen in disk utility but can be seen in system profiler

    HI
    i have a 500gb western digital my passport, its been working fine, since i have used it on a windows machine, i can no longer get it to be recognised in finder. The light is flashing on the side and i can see it under USB in sytem profiler. I cant see it in disk utility. i cant format as it has photos etc loaded
    cheers

    An update for anyone who can help me:
    I have tried the external hard drive in other computers (mac and windows), each time I get the same problem above.
    I have removed the HD from the enclosure and purchased a docking station for it (3.5" SATA). When I plug it in to the laptop it disconnects itself straight away before it is visible. With the windows computers it installs the drivers and says that the device is ready to use, then disconnects before it shows up.
    As the HD is not visible there is no option to re-format or anything.
    This is very frustrating as I was using the HD with no issues and it randomly disconnected and I have not been able to access since.
    Thanks in advance for any help.
    Bruce

Maybe you are looking for

  • How to create a BAM database in enterprise version

    Hi, I need to configure and create a BAM database for my client in an AL Process Interaction installation. I tried to follow the documentation to create the BAM schema, but was not successful. It threw me a message telling me the Driver was not found

  • Why can't iPhone play movies in MobileMe galleries published from iPhoto?

    I have movies published to my MobileMe galleries from iPhoto or QuickTime. They are in .m4v format, but the iPhone doesn't play them. Does anyone know why?

  • HOW to create TAX code in FTXP SCREEN

    Hi guru’s Can anybody explain , hot to maintain the tax code for below mentioned structure. Bed16% ed2%secess1%8.5%deductible4%non deductible. Please explain me stet by step , inFTXP.. what are inputs I need to give.because  in ftxp screen, Thanks mm

  • How do I update AnyConnect on my Android phone (Galaxy III)

    The version of AnyConnect on my cell phone no longer connects. How do I upgrade out. I already updated the version on my iPad but can't figure out where to find the new App.

  • How can I get my navigation bar back?

    Can't see the toolbars: navigation bar, view, tools, etc == This happened == Just once or twice == Today when I was trying to change toolbars. I accidentally unchecked menu bar and everything went. ''asked and answered, repeatedly - locking due to ag