Hard disk drive error

i found an error in the disk utility concerning my HDD so ran a hardware test using the original install disk. it came up with the error 4MOT/1/40000003:HDD and i'm assuming that means my hard drive is close to death? has anyone got advice on what to do in this situation?

After searching, found this Discussions thread and several others which seem to indicate it's maybe the drive fan, not the drive itself. (But don't know why DU is coming up with an error for the drive; maybe a problem with both. What was the drive error?)
http://discussions.info.apple.com/thread.jspa?threadID=2119726&start=15&tstart=0 thread
In Disk Utility, Is the SMART Status Verified?
How is the Drive temperature?
Get Temperature Monitor and post the results in Celsius.
http://www.bresink.com/osx/TemperatureMonitor.html
Or iStat Pro will give temps and readouts of fan rpms
http://www.islayer.com/apps/istatpro/
Smart Utiity demo will alert you to a failing Drive even if it is verified by SMART in DU.
http://www.volitans-software.com/smart_utility.php

Similar Messages

I am a OS10.7.4 user. yesterday i bought a Lacie external hard disk but error message appear said " You cant open the applicant LaCie setup assistant because PowerPC applicants are no longer support". please help me how to connect my mac with Lacie??

i am a OS10.7.4 user. yesterday i bought a Lacie external hard disk but error message appear said " You cant open the applicant LaCie setup assistant because PowerPC applicants are no longer support". please help me how to connect my mac with Lacie??

You do not need the Setup Assistant; in fact, you do not need any software on an external hard drive. I have two LaCie's; I erased the drive as soon as I plugged it in. You will need to format it anyway because most hard drives come Windows formatted. So, if you only want to use it with the Mac, highlight it in Disk Utility and choose Mac OS Extended (Journaled) as the format and the GUID Partition scheme under Options. While doing that, it will erase the drive (and get rid of the LaCie software) - once finished, your drive is ready to use for Time Machine or any other backup plans you have for it.

Mac OSX wont reognise my internal hard disk drive

I have a problem where for some reason when I start up my Macbook Pro (intel core duo) it does not detect the internal hard disk drive at all. I have run a hardware test and it shows no problems whatsoever. I have tried resetting the PRAM etc and to no avail. Yesterday the system hung and I tried to force quit and it wouldn't do anything so eventually I held down the power key and when it tried to reboot this is the problem I was faced with (it would boot up with the "no entry" sign). I accepted complete defeat and went to completely re-install OSX however it doesn't even show the internal hard drive when I wait for it to give me install destinations. I had tried seeing the hard drive through disk utility however it only shows the install DVD and that's it in the sidebar. I resigned myself further to thinking either the logic board or the HDD had packed in all and I took it round to my brother in law to see if there is anything he could do without opening the machine (he is Oxford educated and writes programmes etc so is very knowledgable), now this is the part that has miffed us both, he started it up using a Linux disc and once running, Linux see's the hard drive with no problems. He has been able to access the HDD with absolutely no problems under Linux both reading and writing to it. I even took my Mac Mini round and he booted them both up in Linux and completely copied Mac OSX from the mini to the macbook pro but still when I try booting up its as if the HDD isn't even there. Why can Linux see the drive and not Mac OSX? Please don't be affraid to get very technical in your answers as they may mean nothing to me but will probably all make sense to my brother in Law. Any sugestions at all would be greatly accepted.

Dear mcdkev,
You guys may have made a big error cloning the Mini HD into the MBP. They both have very different drivers and hardware settings and their OS X versions are customized to fit the hardware. That is why each mac comes with it's own version of OS X and their backup disks. That's a reason why it did not work.
Ok, so now that you do not have any of the original info on the MBP try the following:
Use linux to scan the disk surface & repair any problems.
Reformat the drive as DOS or FAT 32. (I wouldn't go into any linux specific format unless you can "Apple" format it, which I don't think linux has that option.)
Now, the MBP should be able to see it's drive...
boot from the OS X DVD , from the Utilities menu choose Disk Utilities, partition the drive as GUI file system (in case the linux format made the drive a "system boot record", you do not want that... )
Then format the drive as "OS X Extended Journaled"
Now go back to install and install your original basic set of OS X (the factory default).
*If nothing works, please do take your MBP to the Apple store or to a certified tech before you do more damage to the drive and it becomes unusable ...*

Qosmio X500/00X System Recovery (Factory Reset) From Hard Disk Drive or Separate Disk

Hey Guys,
Looking for your advice and any links if any...cheers in advance
My Situation
In December 2009 I purchased a Toshiba Qosmio X500 - Model No. PQX33A-00X00J
At the time I upgraded my purchase from Toshiba Reseller BD4U, going from the standard 1x 500GB Sata drive + 1x 64GB SSD... to instead having 2x 500GB sata drives. I purchased with 3 year onsite next business day warranty, that is is now expired.
It came loaded with MS Win 7 Premium Home Edition - but no disks provided.
My Needs
I need/want to factory reset my PC - its starting to run slow
I need to re-partition from my existing 4x partitions to just having 2
The Issues
Possibly as a result of upgrading the disk drives at time of purchase, I don't believe I have a hidden Recovery partition in order to do a System Recovery from the Hard Disk Drive - see image of my current partitions attached
I don't have Win 7 OS installation disks or Toshiba Driver disks as they should have been installed by Toshiba
My Questions
Do You agree that I DONT have a Recovery Partition - when looking at the partition image? I'm confused on this point coz people say its hidden!?
Given I have no Toshiba Drivers Disk or Windows 7 OS disks - what should I do? I'm thinking of downloading Win 7 (use my product key from sticker under PC) and making a disk/USB (but need to learn how)
Is this where I get ALL necessary Toshiba drivers for my PC from?
Does Toshiba provide a link on its site and instructions on where to get Win 7 from so I can make a recover disk??
Notes
Tried to email Toshiba support but at step 1 of their email process validation failed due to my PC being out of warranty so will call them on Monday instead
THANK YOU THANK YOU, for any help you can give big ro small
Cheers
Rick

WOW, thanks Macius for that great, full and thorough reply...cheers mate
I suspected I didn't have a recovery partition - so thanks for confirming it as I planned to risk it and try! I guess it doesn't really matter why, and it would be futile to go and blame the re-seller or Toshiba at this late stage in the game in hopes they would help...
Yeah, I just went to Microsoft Software Recovery hoping to download Win 7 OS and create a recovery disk but of course Microsoft would NOT allow it due to it being software that was pre-installed on the device blah blah blah (see error image)
And I didn't bother back then in 2009 to create recovery media as you wisely descibed, mostly due to laziness and mentally putting it in the 'too hard basket'...I didn't really understand it - or much about computers at the time.
Re - your Option #2 - thanks for confirming Toshiba drivers. I could/can do this - but don't really want to buy something I already have, perhaps I'll check out ebay or see if a friend has a disk
Re - your Option #1 - I'm currently based in Vietnam and wont be back in Oz till late in the year, so will see if I can find a reliable Toshiba service provider here - but wont hold me breath on this one
I'm thinking that IF Option #1 is a No-Go then - maybe Plan B or Option #3 could be:
Do an Audit of Programs to identify those I don't need and can safely remove - then remove using Control Panel/ Remove Programs tool
Reformat all other drives (not C:// where OS is)
Then use some re-partition software e.g. Disk-Partiton.com
Any final thoughts???
Anyhow - thanks very much again
Rick

Arch: Install to & run from External USB Hard Disk Drive (HDD)

I wanted to play with ArchLinux 2009.02, but replacing the existing Debian-Lenny on the laptop's HDD wasn't an option. So I experimented with installing Arch on an external USB Hard Disk Drive.
I have tried to make this "newbie-friendly", so I hope the more experienced will forgive the detail.
Materials:
Three year old Dell Inspiron 6000
CPU = 2.0 GHz Pentium
RAM = 2.0 GB
Internal HDD = 80 GB
Internal CD/DVD R/RW
External USB HDD = Freecom FHD-2 Pro 80 GB
Archlinux 2009.02 install CD
Steps to install:
1. I put the Archlinux install CD in the drive and connected the external 80 GB HDD in the USB port.
2. When the Dell laptop was booted, I pressed F2 to enter the BIOS setup. I edited the boot sequence to the following:
Internal CD/DVD
External USB device
Internal HDD
On the Dell, you can also press F12 to select the preferred boot device for that boot.
3. I started the laptop and the Archlinux installation menu came up and I proceeded with installation following the "Official Arch Linux Install Guide" and the "Beginners Guide".
4. Used km to change to UK keyboard layout and then began the installer script (/arch/setup). I was installing from the core CD so I skipped the network steps.
5. HDD preparation.
This was fairly straightforward with two cautions:
(a) Make very sure that the external HDD (sdb) is selected for the operations.
(b) Remember to set the Bootable Flag for the first (/) partition on the HDD.
I chose 20 GB for /, 2 GB for swap and the remainder for /home.
6. The package selection and installation was fairly straightforward.
7. Configuration of System
This was section was straightforward with one warning:
USB had to be added to the HOOKS in the /etc/mkinitcpio.conf file!
I found this to be essential for my external USB HDD to function as a bootable device. Otherwise I got the same sorts of errors relating to unrecognisable file system types that other people have reported in the forum.
The relevant line from the end of the edited /etc/mkinitcpio.conf file is below:
HOOKS="base udev autodetect pata scsi sata usb filesystems"
8. Installation of GRUB was the other point where caution and/or correction was necessary.
When it asked where GRUB should be installed, I had to select sdb (my external USB HDD) and not any of the particular partitions on sdb. If the root partition sdb1 was selected then the laptop won't boot from the external USB HDD.
The GRUB /boot/grub/menu.lst as written by the installation routine specifies hd(1,0) which doesn't work when you try to reboot from the external USB HDD. When you boot Arch from the external USB HDD, as far as Arch is concerned - at that point in time - the external USB HDD is the first drive in the system. To fix this:
(a) When the Arch boot menu comes up, press e to edit the grub entries.
(b) Change the first line to hd(0,0)
(c) To the end of the kernel line add rootdelay=8
(d) Press b to boot the system with these temporary corrections.
(e) Once your Arch system has booted, edit the /boot/grub/menu.lst to make the above changes permanent.
The relevant portion of my /boot/grub/menu.lst looks like the following:
# (0) Arch Linux
title Arch Linux
root (hd0,0)
kernel /boot/vmlinuz26 root=/dev/disk/by-uuid/... ro rootdelay=8
initrd /boot/kernel26.img
# (1) Arch Linux
title Arch Linux Fallback
root (hd0,0)
kernel /boot/vmlinuz26 root=/dev/disk/by-uuid/... ro rootdelay=8
initrd /boot/kernel26-fallback.img
9. The laptop happily and consistently boots Arch Linux from the external USB HDD when it's plugged in before startup/booting.
Running Arch from the external USB HDD seems as quick as running Debian from the internal HDD.
So if there is a performance penalty associated with using an external USB HDD, my wife and I haven't noticed.
In summary, the three essential points to address during installation to an external USB HDD are:
Remember to set the bootable flag for the first partition.
Add USB to the HOOKS for /etc/mkinitcpio.conf file.
Correct the /etc/grub/menu.lst file.
I hope this is helpful.
Ted

Hi Rookie,
As you say, it is worth remembering the rootfstype= option for the kernel line just in case someone still has problems with GRUB after making all the other changes.
I was working with the most recent Arch 2009.2 release.
I only got messages about unrecognisable file system type when I tried booting with the "stock" or "as-installed" GRUB (before I edited /boot/grub/menu.lst). After editing /boot/grub/menu.lst to identify the drive correctly and add rootdelay, GRUB was able to do the rest and everything worked OK without any error messages.
Best wishes,
Ted

9.2.1 upgrade - hard disk driver prob.

Hi all,
System
PowerPC G4 dig audio dual533
768mb ram
40gb HD - 9.1OS
120gb HD - OSX tiger
I have installed a 2nd hand 120Gb HD which I totally erased writing 0's over it then partitioned (1) MacOS extended.
Loaded OSX tiger onto it and all is sweet no problems at all and loving the new interface!
Now the problem is I want to use my Illust9 & Phsop6 on the old 40gb HD which is running OS9.1.
Tried to access one of the progs via Tiger, classic started up and basically hung on the startup screen so I had to cancel it. That is when the problems started.
I booted up the OS9.1 drive and lost use of my enternet300 adsl internet connection. Reloaded adsl software, didn't fix. Also missing Quicktime VR plus tried using Illust9 and got systems error of controls trip extension. A few other things seemed to go wrong as well.
Read somewhere that it was highly rec to upgrade to 9.2.2 to utilise the classic environment effectively.
As I had lost my internet connection on the old HD I downloaded the Mac OS 9.2.1 Update.smi, Mac OS 9.2.2 Update.smi and HardDriveUpdate1.smi files from my Tiger HD.
Back to the OS9.1 HD to install the updates and it comes up with.....
The hard disk driver on the disk "PowerMac G4 Install" cannot be updated with this program because the disk is not an Apple hard disk. Contact the manufacturer of your computer or hard disk to see if you need to update the driver.
After alot of stuffing around I have done the following in this order.
after each one it didn't fix the problem
1. OS9.1 software restore in place
2. OS9.1 software restore clean install
3. Erased HD and initilised 1 part partition using OS9.1 software install CD
then installed new OS9.1 by booting up from install CD
4. Erased HD and initilised 1 part partition using OSX tiger software install DVD from 120gb HD, then installed new OS9.1 by booting up from install CD
thinking this would sort the driver problem but no go.
same problem when trying to upgrade to 9.2.1!!!!!!!!!!!
any ideas?
40gb HD is a IBM-IC35L040AVER07-0
appreciated
PowerPC G4 digital audio dp533 Mac OS X (10.4.5)
PowerPC G4 digital audio dp533 Mac OS X (10.4.5)
PowerPC G4 digital audio dp533 Mac OS X (10.4.5)

OK,
I have Erased the 40gbHD and erased, initilised it with a 1 part partition using disk utility from the OSX tiger on the 120gb HD, then installed a new OS9.1 by booting up from the OS9.1 install CD.
Used the 9.2.1 upgrade which was downloaded from Apple.
Followed thier instructions in the read me file by
turning extensions to 9.1 base
make sure file sharing is off (wasn't on in the first place)
then restarted
no other apps running and straight into starting the upgrade
started the install process
unchecked the option to update driver
starts to install goes for about 6% and then the box comes up with......
This version of Mac OS can not be installed over the localized version of Mac OS on the disk named "XXXXXXX XXXXX".
Please choose a different destination disk, or perform a clean installation.
SURELY IT CAN"T BE THIS HARD TO UPGRADE FROM 9.1 to 9.2.1 to 9.2
COME ON APPLE help me out here!!!!! FFS!
can't do a clean install, haven't got the disks!!!!!

Turning laptop on computer will give - Hard Disk 301 error

Hey,
This was the last checkpoint for me with my problem.
Firstly I would like to tell what is my problem:
I'm getting hard disk 301 error everytime when I open my computer. I will get error occured in hard disk while using windows.
I checked from samsunghdd.com and there was application called seatoolsDOS, just cannot run it because I cannot access Boot Advance Option. I asked one forum what to do and answer was hard disk drive is dying and Im agreeing that too now.
Okay my HDD is: Samsung HM500JJ 500GB
OS Windows 7 Home Premium
Laptop model: HP DV6 3050so
Problem: Hard disk 301
Im just wondering how long my hard drive can run? I dont have anything to backup. Just want to get resolution to this.
If you want know more just ask. I'm sure I missed something so just ask
Regards Mika Marjomaa
This question was solved.
View Solution.

Hi Mika
The Hard drive can work for 1 day or for 1 year this cannot be guessed. This is a Smart Failure ID which is captured by the unit itself. It is always better to get the part replaced.
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Hard disk drive replaicement

I have a Hard Disk 1 (301) error message, when turning on my laptop. It says something along the lines of "the hard disk has detected an imminent failure".
My laptop is a HP Pavilion G7-1033cl (windows 7), purchased in 2011, so it's out of warranty.
As far as a noticed in some other answers, I shoul replace the hard-disk for sure.
Ok, my question is: What kind of hard disk shoul I buy for replacing it? What's the best recommended?
Thank you for your help!
GStoicu

Whenever the Hard Disk fails with an error Hard Disk 1 [301] that indicates that the Hard Disk Drive has failed and that requires a replacement to resolve the issue
This issue could be due to Application or driver conflicts, virus issues, file corruptions due to incompatible applications, improper shutdowns, update failures due to conflicts, sudden power surges, if notebook is dropped etc..
HP will provide a replacement Hard Disk Drive if the Notebook warranty is Active, If not you need buy a SATA Hard Disk Drive from a retail shop nearby
Please make sure you are getting at least equal capacity as the original one in order to use Recovery Disks. If you need you can buy a larger, but not smaller capacity Hard Disk Drive. For example if you have a 500GB Hard Disk Drive you can upgrade it to 750GB Hard Disk Drive but not 320GB Hard Disk Drive
Please try the below shown troubleshooting steps once:
Step 01. Remove the battery and unplug the AC/Power Adapter
Step 02. Press and hold the Power button for more than 30 Seconds
Step 03. Plug in the AC/Power Adapter (leave the Battery out for now)
Step 04. Press the Power button and check if the Unit works normal
If the above mentioned steps does not help, then you can try reseating the Hard Drive on your Notebook
If the issue persists again please Contact HP if your HP Notebook is under warranty, HP would replace the Hard Disk Drive and provide you a Recovery media to restore factory operating system after replacement (if you've not yet created Recovery Discs/USB Media)
Note: Back up all the personal data to an external drive if it's possible. Otherwise you could connect the failed HDD via SATA to USB adapter with another PC or same PC after replacement of HDD & re-installation of OS and try copying /recovering the files. You can also refer to the below shown link for further support
http://www.wikihow.com/Recover-Data-from-the-Hard-Drive-of-a-Dead-Laptop
Please click on the link In order to Identify, Prevent, Diagnose & Recover from Drive Failures on HP Notebook Hard Drives & Solid State Drives :
http://h10032.www1.hp.com/ctg/Manual/c02876562.pdf
You can Check your warranty Here to verify the status and Click Here to order a new Hard Drive
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP

Hard disk drive in CD-RW case

I received a seagate 20Gb hard disk drive from a friend which had been working in his PC which I hought I could connect in to my iMac in an old external cd writer casing. When I power it up though, the mac can't find the drive. Is this because the CD writer casing is not compatible with hard drives or is it possibly something else?
Cheers
Derek

Settings for master, slave, and cable select are changed by re-positioning the small plastic jumper(s) on the drive. Because the exact configuration of the jumpers varies from one brand to another, you should check the hard drive's manufacturer's web site for specific information.
An additional problem may concern the external case and the bridge chipset used in it. Was this a USB 1.1 CD-RW device? I once had an old Sony Spressa USB 1.1 CD-RW drive and installed a Zip drive in the case, after the CD-RW failed. Even with Iomega's Zip USB driver installed (with the Apple USB Support drivers), the Zip drive would choke when attempting to read anything but a small file on a disk. Attempts to write to a Zip disk, triggered a couple of error messages referring to missing (but necessary) "software." Essentially, the errors pertained to firmware in the ATAPI-to-USB bridge that didn't support the use of a "mass storage device," because it was programmed for an optical removable media device.

Comparison of SSD with hard disk drives

Attribute or characteristic
Solid-state drive
Hard disk drive
Spin-up time
Instantaneous.
May take several seconds. With a large number of drives, spin-up may need to be staggered to limit total power drawn.
Random access time[45]
About 0.1 ms - many times faster than HDDs because data is accessed directly from the flash memory
Ranges from 5–10 ms due to the need to move the heads and wait for the data to rotate under the read/write head
Read latency time[46]
Generally low because the data can be read directly from any location; In applications where hard disk seeks are the limiting factor, this results in faster boot and application launch times (see Amdahl's law).[47]
Generally high since the mechanical components require additional time to get aligned
Consistent read performance[48]
Read performance does not change based on where data is stored on an SSD
If data is written in a fragmented way, reading back the data will have varying response times
Defragmentation
SSDs do not benefit from defragmentation because there is little benefit to reading data sequentially and any defragmentation process adds additional writes on the NAND flash that already have a limited cycle life.[49][50]
HDDs may require defragmentation after continued operations or erasing and writing data, especially involving large files or where the disk space becomes low. [51]
Acoustic levels
SSDs have no moving parts and make no sound
HDDs have moving parts (heads, spindle motor) and have varying levels of sound depending upon model
Mechanical reliability
A lack of moving parts virtually eliminates mechanical breakdowns
HDDs have many moving parts that are all subject to failure over time
Susceptibility toenvironmental factors[47][52][53]
No flying heads or rotating platters to fail as a result of shock, altitude, or vibration
The flying heads and rotating platters are generally susceptible to shock, altitude, and vibration
Magneticsusceptibility[citation needed]
No impact on flash memory
Magnets or magnetic surges can alter data on the media
Weight and size[52]
The weight of flash memory and the circuit board material are very light compared to HDDs
Higher performing HDDs require heavier components than laptop HDDs that are light, but not as light as SSDs
Parallel operation[citation needed]
Some flash controllers can have multiple flash chips reading and writing different data simultaneously
HDDs have multiple heads (one per platter) but they are connected, and share one positioning motor.
Write longevity
Solid state drives that use flash memory have a limited number of writes over the life of the drive.[54][55][56][57] SSDs based on DRAM do not have a limited number of writes.
Magnetic media do not have a limited number of writes.
Software encryption limitations
NAND flash memory cannot be overwritten, but has to be rewritten to previously erased blocks. If a software encryption program encrypts data already on the SSD, the overwritten data is still unsecured, unencrypted, and accessible (drive-based hardware encryption does not have this problem). Also data cannot be securely erased by overwriting the original file without special "Secure Erase" procedures built into the drive.[58]
HDDs can overwrite data directly on the drive in any particular sector.
Cost
As of October 2010, NAND flash SSDs cost about (US)$1.40–2.00 per GB
As of October 2010, HDDs cost about (US)$0.10/GB for 3.5 in and $0.20/GB for 2.5 in drives
Storage capacity
As of October 2010, SSDs come in different sizes up to 2TB but are typically 512GB or less[59]
As of October 2010, HDDs are typically 2-3TB or less
Read/write performance symmetry
Less expensive SSDs typically have write speeds significantly lower than their read speeds. Higher performing SSDs and those from particular manufacturers have a balanced read and write speed.[citation needed]
HDDs generally have symmetrical read and write speeds
Free block availability andTRIM
SSD write performance is significantly impacted by the availability of free, programmable blocks. Previously written data blocks that are no longer in use can be reclaimed by TRIM; however, even with TRIM, fewer free, programmable blocks translates into reduced performance.[25][60][61]
HDDs are not affected by free blocks or the operation (or lack) of the TRIM command
Power consumption
High performance flash-based SSDs generally require 1/2 to 1/3 the power of HDDs; High performance DRAM SSDs generally require as much power as HDDs and consume power when the rest of the system is shut down.[62][63]
High performance HDDs generally require between 12-18 watts; drives designed for notebook computers are typically 2 watts.

I wish I could get my head round the SSD vs HDD with a NLE rig. My builder is trying to persuade me to use a Toshiba 256Gb THNSNC256GBSJ for OS and programs, and it is only NZ$20 more expensive than the 450Gb 10k rpm VelociRaptor I was originally planing to use for the OS. That sounds suspiciously cheap to me, and I am concerned about the finite writes to SSD - mainly because I don't really understand it.
The rest of the new build is
3930K
Gigabyte X79-UD5
8 x DDR3 1600
Coolermaster with 750W PSU
Geforce GTX570
I plan to transfer the drives from my current system as a starting point, and reassess after giving it some use. That means
Either the above SSD or 450Gb 10k Raptor for OS (new drives)
300Gb 10k rpm Raptor (currently used for OS in old box)
150Gb 7k4 rpm Raptor (reserved for Photoshop Scratch in old box)
2 x 1Tb WD Blacks (data drives)
2 x 1Tb WD USB3 externals
I don't know how I would configure the drives in the new box, but have seen Harm's table and will try to follow his advice. It's a dreadful thing to admit, but I don't have a backup strategy, and the above drives are well over half full. Well over! And I am only just getting serious about video, (the rest is mainly CR2 files from my Canon 1Ds3 and 1D4)
I know it must be like banging your head against the wall, but should I avoid that SSD and go with the 450G Raptor? I have read a comment that the WD Blacks don't work well as Raid0. Is that BS or true?
I am about to give the go-ahead so need to confirm the spec.

Just bought a Lenovo 3000 N200 without a hard disk drive, need software

I just bought a Lenovo 3000 N200 Type 0769-BLG assembly date 07/09 from e-bay, it looks brand new but it had a fault, it was dead, perhaps a faulty motherboard and the hard disk drive had been removed. Assuming I can get the fault fixed, where can I get the Lenovo software that came with the original hard disk drive, I would prefer a free source, if that is possible, perhaps some kind person has put all of the CD's on to a DVD that I can borrow or buy a copy of. I was an IBM employee for 30 years before retiring 15 years ago. Dan McLean in Scotland, UK.

Call customer service directly to get a quick solution for this.
IPnaSh
First Spanish Community Guru - Colaborador ad honorem

I can't copy my itunes library to an external hard disk drive!!

this is my first time at the forum and i dont find a better way to ask, i want to copy my itunes library to an external hard disk drive for have a back up, but when i try to copy it it appears this message "the item "itunes music" has 1 or more items that are in use and cannot be modified", i dont know why, then i search for help in apple support and this article http://support.apple.com/kb/HT1751, but i do what it says and i still having my problem, i can't copy my music, that message keep's appearing and it dont let me copy my music.

forget it i discover my problem, this message gives u 2 option stop or continue i just click continue and it get copied, i think this is normal but like this is my fisrt time i dot this i get confused, i think i still used to windows, i cant believe because i have a ear with this computer. well anything is a good experience.

How can I optimize my hard disk drive usage and performance in Windows 8 or Windows 7?

QuestionHow can I optimize my hard disk drive usage and performance in Windows 8 or Windows 7?
AnswerThere are a few simple steps you can take to ensure your hard disk drive is used optimally.
Use Toshiba HDD Protection
Many Toshiba laptops come with a program called Toshiba HDD Protection pre-installed. This program helps to protect your hard disk drive from being damaged due to falls or impacts. By default, it should already be enabled. You might be tempted to lower the detection levels in this application, but doing so could cause your hard disk drive to be damaged. Remember that while the application can reduce the chance of damage, you should still avoid allowing the laptop to fall or suffer rapid impacts.
For more information on this utility, see the following article:
TOSHIBA HDD Protection
Optimize the drive
Windows 8 and Windows 7 optimize hard disk drives automatically through a process called defragmentation. Unless you've disabled this, you don't need to do anything. If you have disabled this and want to run the process, you can still do so.
In Windows 8, search for "Defrag" at the Windows Start screen and select "Defragment and optimize your drives."
In Windows 7, search for "Defrag" in the Start Menu's search field and select "Disk defragmenter."
You can use this tool to optimize your hard disk drives, allowing Windows to find needed files faster.
Remove items from startup
Some applications run automatically when Windows starts. This can add additional functionality, but it also decreases the performance of your computer. Sometimes you might want to disable certain programs from starting automatically.
In Windows 8, search for "Task Manager" at the Start screen. Select the "Startup" tab. Select an application you'd like to disable from starting automatically and then click the "Disable" button in the lower-right.
In Windows 7, type "msconfig" in the Start Menu's search field and press ENTER. Uncheck the boxes next to applications you'd like to disable from starting automatically.
You should be sure of the purpose of an application before disabling it from starting automatically. Some applications might be important. If in doubt, you might consider searching on the Web to discover more information about a program. Remember that if you find that you disabled something vital, you can always re-enable it.
For more information, please see the following video:

QuestionHow can I optimize my hard disk drive usage and performance in Windows 8 or Windows 7?
AnswerThere are a few simple steps you can take to ensure your hard disk drive is used optimally.
Use Toshiba HDD Protection
Many Toshiba laptops come with a program called Toshiba HDD Protection pre-installed. This program helps to protect your hard disk drive from being damaged due to falls or impacts. By default, it should already be enabled. You might be tempted to lower the detection levels in this application, but doing so could cause your hard disk drive to be damaged. Remember that while the application can reduce the chance of damage, you should still avoid allowing the laptop to fall or suffer rapid impacts.
For more information on this utility, see the following article:
TOSHIBA HDD Protection
Optimize the drive
Windows 8 and Windows 7 optimize hard disk drives automatically through a process called defragmentation. Unless you've disabled this, you don't need to do anything. If you have disabled this and want to run the process, you can still do so.
In Windows 8, search for "Defrag" at the Windows Start screen and select "Defragment and optimize your drives."
In Windows 7, search for "Defrag" in the Start Menu's search field and select "Disk defragmenter."
You can use this tool to optimize your hard disk drives, allowing Windows to find needed files faster.
Remove items from startup
Some applications run automatically when Windows starts. This can add additional functionality, but it also decreases the performance of your computer. Sometimes you might want to disable certain programs from starting automatically.
In Windows 8, search for "Task Manager" at the Start screen. Select the "Startup" tab. Select an application you'd like to disable from starting automatically and then click the "Disable" button in the lower-right.
In Windows 7, type "msconfig" in the Start Menu's search field and press ENTER. Uncheck the boxes next to applications you'd like to disable from starting automatically.
You should be sure of the purpose of an application before disabling it from starting automatically. Some applications might be important. If in doubt, you might consider searching on the Web to discover more information about a program. Remember that if you find that you disabled something vital, you can always re-enable it.
For more information, please see the following video:

Satellite M30X - high hard disk drive utilization

After login in Windows XP (SP2), my toshiba laptop is very slow. The hard disk drive light is continuously on for 5 minutes. I've looked at the task manager, but CPU utilization is low and RAM usage is low. There is no program that seems to use a lot of CPU or RAM.
I've actually turned off the paging file to see if the problems due to intensive use of the paging file on the HDD, but problem persists. The model of the laptop is Satellite M30X-113.
I don't know if it's related, but this problem arose around the time that I've taken out a 256 MB RAM module and installed a 512 MB one (making the total ram memory 1024 MB).

Hi
> I don't know if it's related, but this problem arose around the time that I've taken out a 256 MB RAM module and installed a 512 MB one (making the total ram memory 1024 MB).
If this issue has begun after installation of the new memory module then I would say that the new memory module is responsible for this issue.
You could also try to put back the 256MB module to check if the issue still persist.
This would be the easiest way for checking

Can I upgrade MacBook Pro hard disk drive next year?

Hi there! I'm new to the Apple Support Communities!
I am going to buy a new 13" MacBook Pro, 2.5GHz. I am going to buy the base model, with a 500GB 5400 RPM hard disk drive. Right now, I can't afford a 256GB solid-state drive, but I'll have enough for one by later next year. So, I will have done some stuff on my Mac by the time I can upgrade it. I know how to install the drive itself, but how do I transfer my information?
Here are the issues:
1) I don't know how I would make it so I could boot from an external USB.
2) And I don't know how to get all my personal information from one drive to the other.
For "2", I think I could back up my Mac to a hard drive with Time Machine, and then restore from a backup. But Time Machine couldn't back up the whole OS, right? And what would the procedure be anyway? Just turn it on when I'm done the upgrade?
If someone who has done this before could provide step-by-step instructions, I would really appreciate it!
Thanks,
Solid-State Me 

Yes you can replace the hard drive at any time. Purchase a replacement drive from any store you like - newegg or mcetech are good stores (among many others) - and when you purchase the new drive, also purchase a drive enclosure. Then download a program called "super duper" and follow the instructions to use that software. When your drive arrives, put the new drive in the enclosure, plug it in to your computer and run "super duper" with the option to "make the drive bootable" and let it finish. What it's doing is copying your drive onto the new drive. Once the copy is finished, you can shut down your computer, remove the drive, install the new one, and put the original drive into the enclosure. Now you have an external hard drive that is repurposed instead of throwing it away. Keep that drive intact for a few weeks without erasing or adding data to be sure you are happy with the new drive and how it performs. After that, use the drive to store files, backup the internal, transfer stuff, whatever.

Hard disk drive error

Similar Messages

Maybe you are looking for