Hard disk drive retrieval after drinks spill?

My son spilt liquid on his MacBook Pro and the keyboard and power switch have gone so it's not worth repairing and I've bought a new MacBook.
However he wants to retrieve some data from the old hard disk drive,especially music.
I believe you can take out the old hard disk,put it in an enclosure and connect up with a specific cable to his new MacBook,and extract what is required from the old hard disk.
Can anyone confirm on this?
Thanks.

Yes remove the drive but instead of getting a Drive Enclosure get a SATA to USB Adapter. Much more versatile and comes with a AC power adapter to make sure the drive is being properly powered up. Notebook size enclosures usually only use USB power to power the drive and that can be flaky on a Mac notebook.

Similar Messages

Verify physical hard disk drive health MCS 7825-H3 that installed CUCM inside it

Hi Everyone,
I have Cisco MCS 7825-3 that installed CUCM ver 6.1.1 inside it. A few days ago the system was crashed and have been recovered. And the symtomp why the system crashed is because corrupted hard disk drive. Now the system is running well.
I want to verify the health status of hard disk drive MCS 7825. The logical drive is RAID 1 with 2 chunks (channel 0,1 and channel 0,2). So that i did the test to shut down the cucm and unmount on of the physical hard disk drive. After that i power on the server and running the system with just 1 hard disk drive (example just channel 0,1 and after verify channel i do the same task with channel 0,2). With just 1 hard disk drive if i show hardware in cucm cli , it showed that status of logical drive is degraded. But the system can run well (IP Phone registered and can do pbx features). And after do verify test with 1 hard disk drive, i mount the physical hard disk drive again so that the system running with all of hard disk drive mounted (2 chunks).
At first it showed in cucm cli that status of logical drive is degraded, but with current operation rebuild (indicated RAID 1 is rebuild again by the system). After up to 1 hour the process finished and the status of logical drive is optimal again.
The question i wanna ask, is there any method to know if the health of physical hard disk drive of MCS good or not beside the task i have done ?
Maybe we can show in the BIOS or cucm cli because i didnt find diagnose of physical drive in cucm cli but it can diagnose status of RAID, hard disk space and list file in hard disk drive.
Thanks for your help.
Best Regards,
Luthfi
- See more at: https://supportforums.cisco.com/message/3871634#3871634

Hi Luthfi,
Do you find a way to check the hard drives and RAID of this CUCM server. I have also 7825-H3
Or it is as I think that I need to create remote access configuration ?
Thanks
Haitham

Verify physical hard disk drive health MCS 7825-H3

Hi Everyone,
I have Cisco MCS 7825-3 that installed CUCM ver 6.1.1 inside it. A few days ago the system was crashed and have been recovered. And the symtomp why the system crashed is because corrupted hard disk drive. Now the system is running well.
I want to verify the health status of hard disk drive MCS 7825. The logical drive is RAID 1 with 2 chunks (channel 0,1 and channel 0,2). So that i did the test to shut down the cucm and unmount on of the physical hard disk drive. After that i power on the server and running the system with just 1 hard disk drive (example just channel 0,1 and after verify channel i do the same task with channel 0,2). With just 1 hard disk drive if i show hardware in cucm cli , it showed that status of logical drive is degraded. But the system can run well (IP Phone registered and can do pbx features). And after do verify test with 1 hard disk drive, i mount the physical hard disk drive again so that the system running with all of hard disk drive mounted (2 chunks).
At first it showed in cucm cli that status of logical drive is degraded, but with current operation rebuild (indicated RAID 1 is rebuild again by the system). After up to 1 hour the process finished and the status of logical drive is optimal again.
The question i wanna ask, is there any method to know if the health of physical hard disk drive of MCS good or not beside the task i have done ?
Maybe we can show in the BIOS or cucm cli because i didnt find diagnose of physical drive in cucm cli but it can diagnose status of RAID, hard disk space and list file in hard disk drive.
Thanks for your help.
Best Regards,
Luthfi

Hi Luthfi,
Do you find a way to check the hard drives and RAID of this CUCM server. I have also 7825-H3
Or it is as I think that I need to create remote access configuration ?
Thanks
Haitham

DV9925nr - How to Backup Hard Disk Drive After S.M.A.R.T. Drive Failure Message

I purchased a DV9925nr laptop from Bestbuy about 13 months ago. Six months ago it started having the sporadic and randomly abrubt shutdown problem that so many others seem to be having.
Two days ago it developed a new problem:
I left my laptop on for a few minutes and when I returned, it was to a black screen with this message: "SMART Drive failure predicted on Hard Disk 4. WDC WD2500BEVS - 60UST0-(S1); warning: Immediately backup your data and replace your hard disk drive. A failure may be imminent. Press F1 to continue."
My question:
We have a network with two laptops and a desktop computer. There is plenty of hard drive space on the desktop system. My father has the same exact laptop model as mine. Can I put my hard disk drive into his second disk drive bay so that I can backup my files over the network to my desktop system? How would the laptop know which hard drive to boot from since they both have the same operating system on them (I am not familiar with SATA drives)?
I hope I didn't buy a lemon. Any help would be greatly appreciated.

Are you trying to do this while booted from the OS or from the install Disk? If your booted into the OS then the repair option shouldn't be click-able. Beyond that, there might be some 3rd party software that could force a reformat and/or erase. I did try to find you something but didn't come across anything specific to what your trying to do. You probably already know this, but the purpose of S.M.A.R.T. is it acts as an early warning indicator. This means the drive is no longer dependable and may fail without warning in the near future, resulting in losing all data. With that being said, I've used a hard drive that S.M.A.R.T. indicated was failing for 3+ years without a hick-up. I don't use it for anything imported though. When I have more time and if I come across anything that might get the job down, I will add to this posting. The worst case scenario is that there is no way to reformat and/or erase the drive due to the state it's in. At that point, the only thing left to do is recycling the drive.

Comparison of SSD with hard disk drives

Attribute or characteristic
Solid-state drive
Hard disk drive
Spin-up time
Instantaneous.
May take several seconds. With a large number of drives, spin-up may need to be staggered to limit total power drawn.
Random access time[45]
About 0.1 ms - many times faster than HDDs because data is accessed directly from the flash memory
Ranges from 5–10 ms due to the need to move the heads and wait for the data to rotate under the read/write head
Read latency time[46]
Generally low because the data can be read directly from any location; In applications where hard disk seeks are the limiting factor, this results in faster boot and application launch times (see Amdahl's law).[47]
Generally high since the mechanical components require additional time to get aligned
Consistent read performance[48]
Read performance does not change based on where data is stored on an SSD
If data is written in a fragmented way, reading back the data will have varying response times
Defragmentation
SSDs do not benefit from defragmentation because there is little benefit to reading data sequentially and any defragmentation process adds additional writes on the NAND flash that already have a limited cycle life.[49][50]
HDDs may require defragmentation after continued operations or erasing and writing data, especially involving large files or where the disk space becomes low. [51]
Acoustic levels
SSDs have no moving parts and make no sound
HDDs have moving parts (heads, spindle motor) and have varying levels of sound depending upon model
Mechanical reliability
A lack of moving parts virtually eliminates mechanical breakdowns
HDDs have many moving parts that are all subject to failure over time
Susceptibility toenvironmental factors[47][52][53]
No flying heads or rotating platters to fail as a result of shock, altitude, or vibration
The flying heads and rotating platters are generally susceptible to shock, altitude, and vibration
Magneticsusceptibility[citation needed]
No impact on flash memory
Magnets or magnetic surges can alter data on the media
Weight and size[52]
The weight of flash memory and the circuit board material are very light compared to HDDs
Higher performing HDDs require heavier components than laptop HDDs that are light, but not as light as SSDs
Parallel operation[citation needed]
Some flash controllers can have multiple flash chips reading and writing different data simultaneously
HDDs have multiple heads (one per platter) but they are connected, and share one positioning motor.
Write longevity
Solid state drives that use flash memory have a limited number of writes over the life of the drive.[54][55][56][57] SSDs based on DRAM do not have a limited number of writes.
Magnetic media do not have a limited number of writes.
Software encryption limitations
NAND flash memory cannot be overwritten, but has to be rewritten to previously erased blocks. If a software encryption program encrypts data already on the SSD, the overwritten data is still unsecured, unencrypted, and accessible (drive-based hardware encryption does not have this problem). Also data cannot be securely erased by overwriting the original file without special "Secure Erase" procedures built into the drive.[58]
HDDs can overwrite data directly on the drive in any particular sector.
Cost
As of October 2010, NAND flash SSDs cost about (US)$1.40–2.00 per GB
As of October 2010, HDDs cost about (US)$0.10/GB for 3.5 in and $0.20/GB for 2.5 in drives
Storage capacity
As of October 2010, SSDs come in different sizes up to 2TB but are typically 512GB or less[59]
As of October 2010, HDDs are typically 2-3TB or less
Read/write performance symmetry
Less expensive SSDs typically have write speeds significantly lower than their read speeds. Higher performing SSDs and those from particular manufacturers have a balanced read and write speed.[citation needed]
HDDs generally have symmetrical read and write speeds
Free block availability andTRIM
SSD write performance is significantly impacted by the availability of free, programmable blocks. Previously written data blocks that are no longer in use can be reclaimed by TRIM; however, even with TRIM, fewer free, programmable blocks translates into reduced performance.[25][60][61]
HDDs are not affected by free blocks or the operation (or lack) of the TRIM command
Power consumption
High performance flash-based SSDs generally require 1/2 to 1/3 the power of HDDs; High performance DRAM SSDs generally require as much power as HDDs and consume power when the rest of the system is shut down.[62][63]
High performance HDDs generally require between 12-18 watts; drives designed for notebook computers are typically 2 watts.

I wish I could get my head round the SSD vs HDD with a NLE rig. My builder is trying to persuade me to use a Toshiba 256Gb THNSNC256GBSJ for OS and programs, and it is only NZ$20 more expensive than the 450Gb 10k rpm VelociRaptor I was originally planing to use for the OS. That sounds suspiciously cheap to me, and I am concerned about the finite writes to SSD - mainly because I don't really understand it.
The rest of the new build is
3930K
Gigabyte X79-UD5
8 x DDR3 1600
Coolermaster with 750W PSU
Geforce GTX570
I plan to transfer the drives from my current system as a starting point, and reassess after giving it some use. That means
Either the above SSD or 450Gb 10k Raptor for OS (new drives)
300Gb 10k rpm Raptor (currently used for OS in old box)
150Gb 7k4 rpm Raptor (reserved for Photoshop Scratch in old box)
2 x 1Tb WD Blacks (data drives)
2 x 1Tb WD USB3 externals
I don't know how I would configure the drives in the new box, but have seen Harm's table and will try to follow his advice. It's a dreadful thing to admit, but I don't have a backup strategy, and the above drives are well over half full. Well over! And I am only just getting serious about video, (the rest is mainly CR2 files from my Canon 1Ds3 and 1D4)
I know it must be like banging your head against the wall, but should I avoid that SSD and go with the 450G Raptor? I have read a comment that the WD Blacks don't work well as Raid0. Is that BS or true?
I am about to give the go-ahead so need to confirm the spec.

Satellite M30X - high hard disk drive utilization

After login in Windows XP (SP2), my toshiba laptop is very slow. The hard disk drive light is continuously on for 5 minutes. I've looked at the task manager, but CPU utilization is low and RAM usage is low. There is no program that seems to use a lot of CPU or RAM.
I've actually turned off the paging file to see if the problems due to intensive use of the paging file on the HDD, but problem persists. The model of the laptop is Satellite M30X-113.
I don't know if it's related, but this problem arose around the time that I've taken out a 256 MB RAM module and installed a 512 MB one (making the total ram memory 1024 MB).

Hi
> I don't know if it's related, but this problem arose around the time that I've taken out a 256 MB RAM module and installed a 512 MB one (making the total ram memory 1024 MB).
If this issue has begun after installation of the new memory module then I would say that the new memory module is responsible for this issue.
You could also try to put back the 256MB module to check if the issue still persist.
This would be the easiest way for checking

Can I upgrade MacBook Pro hard disk drive next year?

Hi there! I'm new to the Apple Support Communities!
I am going to buy a new 13" MacBook Pro, 2.5GHz. I am going to buy the base model, with a 500GB 5400 RPM hard disk drive. Right now, I can't afford a 256GB solid-state drive, but I'll have enough for one by later next year. So, I will have done some stuff on my Mac by the time I can upgrade it. I know how to install the drive itself, but how do I transfer my information?
Here are the issues:
1) I don't know how I would make it so I could boot from an external USB.
2) And I don't know how to get all my personal information from one drive to the other.
For "2", I think I could back up my Mac to a hard drive with Time Machine, and then restore from a backup. But Time Machine couldn't back up the whole OS, right? And what would the procedure be anyway? Just turn it on when I'm done the upgrade?
If someone who has done this before could provide step-by-step instructions, I would really appreciate it!
Thanks,
Solid-State Me 

Yes you can replace the hard drive at any time. Purchase a replacement drive from any store you like - newegg or mcetech are good stores (among many others) - and when you purchase the new drive, also purchase a drive enclosure. Then download a program called "super duper" and follow the instructions to use that software. When your drive arrives, put the new drive in the enclosure, plug it in to your computer and run "super duper" with the option to "make the drive bootable" and let it finish. What it's doing is copying your drive onto the new drive. Once the copy is finished, you can shut down your computer, remove the drive, install the new one, and put the original drive into the enclosure. Now you have an external hard drive that is repurposed instead of throwing it away. Keep that drive intact for a few weeks without erasing or adding data to be sure you are happy with the new drive and how it performs. After that, use the drive to store files, backup the internal, transfer stuff, whatever.

Hi there! yesterday I installed Mavericks on my Macbook. Since then, it doesn't mount my external hard disk drive anymore, which he did a week ago (without the update). Is there anyone out there who knows a solution?

Hi there! Yesterday, I installed Mavericks on my Macbook. Since then, it doesn't recognize my external hard disk drive anymore (at least not on the desktop. In Germany they call it "it doens't mount it". I don't know if it's the same expression in english?)
I just used it a week ago, before I did the update and it worked perfectly fine.
Is there anyone out there who knows a solution for this problem? I've been googleing for hours now and can't find any answer.
Thank you!!!

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Hard disk drive doesn't appear on home screen

I have a external hard disk drive in NTFS. I have there a lot of data I need to transfer to my new Mac, so I can't erase nothing from there. I installed MacFUSE and Paragon 9 to correct the issue, but after that, the drive just didn't appear anymore on the home screen. It is in Disk utility (in grey color), but I can't mount it and the Fix Disk doesn't help at all. So now I have hard disk drive that doesn't appear to even exist, even the system can find it.
Can anyone say anything constructive?

Look on the other screens (swipe left). If desired, move it to the first screen.
http://manuals.info.apple.com/en_US/iphone_user_guide.pdf

I have apple macbook pro mid 2009 ... my hard disk stopped working and i had mac os 10.6.8 in it ... i bought a new hard disk drive but i didn't have my CD so i installed my friend's mac os 10.5.8 in the new hard disk ... i want to get my 10.6.8 back

I have apple macbook pro mid 2009 ... my hard disk stopped working and i had mac os 10.6.8 in it ... i bought a new hard disk drive but i didn't have my CD so i installed my friend's mac os 10.5.8 in the new hard disk ... i want to get my previous 10.6.8 back ... hope there is a way to do so

Upgrading to Snow Leopard
You must purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
     Snow Leopard General Requirements
       1. Mac computer with an Intel processor
       2. 1GB of memory
       3. 5GB of available disk space
       4. DVD drive for installation
       5. Some features require a compatible Internet service provider;
           fees may apply.
       6. Some features require Apple’s MobileMe service; fees and
           terms apply.

Access external USB hard disk drive with REISERFS Linux filesystem.

I recently bought second-hand an older MBP Pro (2006 model) with Tiger installed, which I use as a desktop system at home and I would like to be able to connect an external IOMEGA 500 GB hard disk drive to it and have read/write access to its contents (mostly video / picture / music files). I spent a while searching on the Internet for solutions - nothing usefule came up. Does anyone in here have any ideas on how to do this? Is it possible at all after all?
P.S.: Apart from this older MBP Pro, I also have a newer model (bought in early 2008) with Leopard installed - I wouldn't mind finding some solution on my problem on that OS instead...

Hi,
The two ways I can see to possibly do it are to network the Linux machine & Drive, then use Samba to access it.
By using the Mac OS X Virtual File System (VFS) capability and writing kernel extensions, you can add support for other file systems. Examples of file systems that are not currently supported in Mac OS X but that you may wish to add to the system include the Andrew file system (AFS) and the Reiser file system (ReiserFS). If you want to support a new volume format or networking protocol, you’ll need to write a file-system kernel extension.
http://developer.apple.com/documentation/Darwin/Conceptual/KernelProgramming/Fil esystem/chapter12_section1.html

Arch: Install to & run from External USB Hard Disk Drive (HDD)

I wanted to play with ArchLinux 2009.02, but replacing the existing Debian-Lenny on the laptop's HDD wasn't an option. So I experimented with installing Arch on an external USB Hard Disk Drive.
I have tried to make this "newbie-friendly", so I hope the more experienced will forgive the detail.
Materials:
Three year old Dell Inspiron 6000
CPU = 2.0 GHz Pentium
RAM = 2.0 GB
Internal HDD = 80 GB
Internal CD/DVD R/RW
External USB HDD = Freecom FHD-2 Pro 80 GB
Archlinux 2009.02 install CD
Steps to install:
1. I put the Archlinux install CD in the drive and connected the external 80 GB HDD in the USB port.
2. When the Dell laptop was booted, I pressed F2 to enter the BIOS setup. I edited the boot sequence to the following:
Internal CD/DVD
External USB device
Internal HDD
On the Dell, you can also press F12 to select the preferred boot device for that boot.
3. I started the laptop and the Archlinux installation menu came up and I proceeded with installation following the "Official Arch Linux Install Guide" and the "Beginners Guide".
4. Used km to change to UK keyboard layout and then began the installer script (/arch/setup). I was installing from the core CD so I skipped the network steps.
5. HDD preparation.
This was fairly straightforward with two cautions:
(a) Make very sure that the external HDD (sdb) is selected for the operations.
(b) Remember to set the Bootable Flag for the first (/) partition on the HDD.
I chose 20 GB for /, 2 GB for swap and the remainder for /home.
6. The package selection and installation was fairly straightforward.
7. Configuration of System
This was section was straightforward with one warning:
USB had to be added to the HOOKS in the /etc/mkinitcpio.conf file!
I found this to be essential for my external USB HDD to function as a bootable device. Otherwise I got the same sorts of errors relating to unrecognisable file system types that other people have reported in the forum.
The relevant line from the end of the edited /etc/mkinitcpio.conf file is below:
HOOKS="base udev autodetect pata scsi sata usb filesystems"
8. Installation of GRUB was the other point where caution and/or correction was necessary.
When it asked where GRUB should be installed, I had to select sdb (my external USB HDD) and not any of the particular partitions on sdb. If the root partition sdb1 was selected then the laptop won't boot from the external USB HDD.
The GRUB /boot/grub/menu.lst as written by the installation routine specifies hd(1,0) which doesn't work when you try to reboot from the external USB HDD. When you boot Arch from the external USB HDD, as far as Arch is concerned - at that point in time - the external USB HDD is the first drive in the system. To fix this:
(a) When the Arch boot menu comes up, press e to edit the grub entries.
(b) Change the first line to hd(0,0)
(c) To the end of the kernel line add rootdelay=8
(d) Press b to boot the system with these temporary corrections.
(e) Once your Arch system has booted, edit the /boot/grub/menu.lst to make the above changes permanent.
The relevant portion of my /boot/grub/menu.lst looks like the following:
# (0) Arch Linux
title Arch Linux
root (hd0,0)
kernel /boot/vmlinuz26 root=/dev/disk/by-uuid/... ro rootdelay=8
initrd /boot/kernel26.img
# (1) Arch Linux
title Arch Linux Fallback
root (hd0,0)
kernel /boot/vmlinuz26 root=/dev/disk/by-uuid/... ro rootdelay=8
initrd /boot/kernel26-fallback.img
9. The laptop happily and consistently boots Arch Linux from the external USB HDD when it's plugged in before startup/booting.
Running Arch from the external USB HDD seems as quick as running Debian from the internal HDD.
So if there is a performance penalty associated with using an external USB HDD, my wife and I haven't noticed.
In summary, the three essential points to address during installation to an external USB HDD are:
Remember to set the bootable flag for the first partition.
Add USB to the HOOKS for /etc/mkinitcpio.conf file.
Correct the /etc/grub/menu.lst file.
I hope this is helpful.
Ted

Hi Rookie,
As you say, it is worth remembering the rootfstype= option for the kernel line just in case someone still has problems with GRUB after making all the other changes.
I was working with the most recent Arch 2009.2 release.
I only got messages about unrecognisable file system type when I tried booting with the "stock" or "as-installed" GRUB (before I edited /boot/grub/menu.lst). After editing /boot/grub/menu.lst to identify the drive correctly and add rootdelay, GRUB was able to do the rest and everything worked OK without any error messages.
Best wishes,
Ted

9.2.1 upgrade - hard disk driver prob.

Hi all,
System
PowerPC G4 dig audio dual533
768mb ram
40gb HD - 9.1OS
120gb HD - OSX tiger
I have installed a 2nd hand 120Gb HD which I totally erased writing 0's over it then partitioned (1) MacOS extended.
Loaded OSX tiger onto it and all is sweet no problems at all and loving the new interface!
Now the problem is I want to use my Illust9 & Phsop6 on the old 40gb HD which is running OS9.1.
Tried to access one of the progs via Tiger, classic started up and basically hung on the startup screen so I had to cancel it. That is when the problems started.
I booted up the OS9.1 drive and lost use of my enternet300 adsl internet connection. Reloaded adsl software, didn't fix. Also missing Quicktime VR plus tried using Illust9 and got systems error of controls trip extension. A few other things seemed to go wrong as well.
Read somewhere that it was highly rec to upgrade to 9.2.2 to utilise the classic environment effectively.
As I had lost my internet connection on the old HD I downloaded the Mac OS 9.2.1 Update.smi, Mac OS 9.2.2 Update.smi and HardDriveUpdate1.smi files from my Tiger HD.
Back to the OS9.1 HD to install the updates and it comes up with.....
The hard disk driver on the disk "PowerMac G4 Install" cannot be updated with this program because the disk is not an Apple hard disk. Contact the manufacturer of your computer or hard disk to see if you need to update the driver.
After alot of stuffing around I have done the following in this order.
after each one it didn't fix the problem
1. OS9.1 software restore in place
2. OS9.1 software restore clean install
3. Erased HD and initilised 1 part partition using OS9.1 software install CD
then installed new OS9.1 by booting up from install CD
4. Erased HD and initilised 1 part partition using OSX tiger software install DVD from 120gb HD, then installed new OS9.1 by booting up from install CD
thinking this would sort the driver problem but no go.
same problem when trying to upgrade to 9.2.1!!!!!!!!!!!
any ideas?
40gb HD is a IBM-IC35L040AVER07-0
appreciated
PowerPC G4 digital audio dp533 Mac OS X (10.4.5)
PowerPC G4 digital audio dp533 Mac OS X (10.4.5)
PowerPC G4 digital audio dp533 Mac OS X (10.4.5)

OK,
I have Erased the 40gbHD and erased, initilised it with a 1 part partition using disk utility from the OSX tiger on the 120gb HD, then installed a new OS9.1 by booting up from the OS9.1 install CD.
Used the 9.2.1 upgrade which was downloaded from Apple.
Followed thier instructions in the read me file by
turning extensions to 9.1 base
make sure file sharing is off (wasn't on in the first place)
then restarted
no other apps running and straight into starting the upgrade
started the install process
unchecked the option to update driver
starts to install goes for about 6% and then the box comes up with......
This version of Mac OS can not be installed over the localized version of Mac OS on the disk named "XXXXXXX XXXXX".
Please choose a different destination disk, or perform a clean installation.
SURELY IT CAN"T BE THIS HARD TO UPGRADE FROM 9.1 to 9.2.1 to 9.2
COME ON APPLE help me out here!!!!! FFS!
can't do a clean install, haven't got the disks!!!!!

SecuRed Hard Disk Drive

Hi
SecuRed Hard Disk Drive:
Does anyone know how I can get this device back to the factory settings as someone has created a vault container and I would like the entire hardisk to be encrypted? I have all the relevant passwords etc for the encryption. Operating system is XP SP3.
Thanks in Advance
CJV

Hi mate,
I had the same problem and after raising a request @ the toshiba hotline, I get the information to send the HDD to an service partner because they can set it back to factory defaults.
After sending it to the ASP here in croatia, I received my HDD with factory settings again.
Hope that helps.
Greets
Dennis

Hard disk drive replaicement

I have a Hard Disk 1 (301) error message, when turning on my laptop. It says something along the lines of "the hard disk has detected an imminent failure".
My laptop is a HP Pavilion G7-1033cl (windows 7), purchased in 2011, so it's out of warranty.
As far as a noticed in some other answers, I shoul replace the hard-disk for sure.
Ok, my question is: What kind of hard disk shoul I buy for replacing it? What's the best recommended?
Thank you for your help!
GStoicu

Whenever the Hard Disk fails with an error Hard Disk 1 [301] that indicates that the Hard Disk Drive has failed and that requires a replacement to resolve the issue
This issue could be due to Application or driver conflicts, virus issues, file corruptions due to incompatible applications, improper shutdowns, update failures due to conflicts, sudden power surges, if notebook is dropped etc..
HP will provide a replacement Hard Disk Drive if the Notebook warranty is Active, If not you need buy a SATA Hard Disk Drive from a retail shop nearby
Please make sure you are getting at least equal capacity as the original one in order to use Recovery Disks. If you need you can buy a larger, but not smaller capacity Hard Disk Drive. For example if you have a 500GB Hard Disk Drive you can upgrade it to 750GB Hard Disk Drive but not 320GB Hard Disk Drive
Please try the below shown troubleshooting steps once:
Step 01. Remove the battery and unplug the AC/Power Adapter
Step 02. Press and hold the Power button for more than 30 Seconds
Step 03. Plug in the AC/Power Adapter (leave the Battery out for now)
Step 04. Press the Power button and check if the Unit works normal
If the above mentioned steps does not help, then you can try reseating the Hard Drive on your Notebook
If the issue persists again please Contact HP if your HP Notebook is under warranty, HP would replace the Hard Disk Drive and provide you a Recovery media to restore factory operating system after replacement (if you've not yet created Recovery Discs/USB Media)
Note: Back up all the personal data to an external drive if it's possible. Otherwise you could connect the failed HDD via SATA to USB adapter with another PC or same PC after replacement of HDD & re-installation of OS and try copying /recovering the files. You can also refer to the below shown link for further support
http://www.wikihow.com/Recover-Data-from-the-Hard-Drive-of-a-Dead-Laptop
Please click on the link In order to Identify, Prevent, Diagnose & Recover from Drive Failures on HP Notebook Hard Drives & Solid State Drives :
http://h10032.www1.hp.com/ctg/Manual/c02876562.pdf
You can Check your warranty Here to verify the status and Click Here to order a new Hard Drive
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP

Hard disk drive retrieval after drinks spill?

Similar Messages

Maybe you are looking for