Hard drive not recoginized [solved]

my new har drive under is dected by 
fdisk -l
but is read only under my file manager-- dollphin
Last edited by shoelesshunter (2015-01-13 01:13:10)

#/dev/mapper/tux-lvroot                         /               ext4            defaults                        0 1
UUID=99445bdb-fb6f-4286-b126-657ff5bff083       /               ext4            rw,relatime,data=ordered        0 1
#/dev/mapper/tux-lvvar                          /var            ext4            defaults                        0 0
UUID=41b35064-b9fb-4117-898c-6a3c3586b53f       /var            ext4            rw,relatime,data=ordered        0 2
#/dev/mapper/tux-lvtmp                          /tmp            tmpfs           defaults                        0 0
UUID=2df1d2e7-0f65-457c-8d57-e0a4b2e956cb       /tmp            ext4            rw,relatime,data=ordered        0 2
#/dev/mapper/tux-lvhome                         /home           ext4            defaults                        0 2
UUID=dbadb7bd-a20b-4342-9bfc-dc01a45a01e0       /home           ext4            defaults        0 2
#/dev/sda1                                      /boot           ext2            defaults        0 2
UUID=3a233d37-f4e4-4679-9b28-fe59f1adb0c6       /boot           ext2            rw,relatime     0 2
#/dev/mapper/tux-lvswap                         none            swap            defaults        0 0
UUID=5282e236-a122-4dd9-b463-1d3dd6b9b88a       none            swap            defaults        0 0

Similar Messages

  • Memory modules and hard drive not recognized

    I removed and reinserted the factory installed Satellite L505D-LS5007 laptop hard drive and memory modules just as practice for installing a hard drive upgrade and an 8GB memory upgrade. The problem is obviously with the memory and not with the hard drive.
    After the first practice try, one memory module was recognized. Also for a few seconds after the first practice try, I ran the PC with the battery installed, but no memory installed. I did not look in the User's Guide first to see that I should have removed the battery before removing the memory.
    Now the System Indicator Lights for the HDD Activity and Memory Card Reader do not light up. The PC turns on and the display is solid black with no messages.
    Before buying new memory modules, what possible ways might there be to get the PC to recognize the factory installed memory modules and hard drive again?
    Solved!
    Go to Solution.

    When troubleshooting, I always change one variable at a time. I would hate to miss a solution by being in a hurry. In this case, you may have damaged either the RAM or the RAM slot. I would stick with the Toshiba specifications for the RAM, making sure it is the correct size, speed and type recommended. I also recommend that when you replace the RAM that both modules be from the same manufacturer, size, and specification. Try one RAM module in one slot and then the other. And then try both RAM modules in both slots. After the testing you should be able to figure if this is a RAM problem or a RAM slot problem.
    In the case of hard drives, the real test is whether or not the Bios sees the hard drive. If the Bios doesn't see the hard drive, it's not going to work. The Bios should see the hard drive whether or not the hard drive is partitioned, formatted or has data on it. My experience has been that many Toshiba laptops will work fine with larger capacity hard drives provided they are the same speed in RPMs, have the same interfacing connection and physically the same size.
    Again, prior to doing any work on your computer, make sure that both the AC power has been disconnected and the battery has been removed. Be careful out there. A blown repair job by a non-Toshiba tech is NOT covered under warranty.

  • Advanced Format Hard Drive not recognized by HP DV6000 Controller

    Hello,
    I have an HP DV 6000 laptop (6276 I think, I'm at work can't check) that came preinstalled with a Western Digital 160gb 1.5gb/s 5400 RPM drive (Vista) that failed a couple of weeks ago.  So i bought a Western Digital 750 GB WD Black SATA III 7200 RPM 16 MB drive to replace it. I read about people having some problems with Advanced Drive Format hard drives not being recognized by their controller, but also read that depending on the controller and specific Dv6000 model laptop they had-one wouldn't run into problems. 
    Well sure enough, when attempting to install Windows 7 I received the error that the hard drive was not detected. After researching online I came across an article on WD's site that noted
    "Our SATA II hard drives use autospeed negotiation. This enables our SATA II drives to automatically detect the motherboard data transfer rate, making it backward compatible with SATA I data transfer rates. However, some older SATA I controllers are unable to support autospeed negotiation and cannot recognize the drive. This “drive not detected” condition occurs when a chipset is incapable of correctly negotiating the data transfer speed with a SATA II hard drive."
    my drive is a SATA ||| but I'm pretty sure it's the same problem.  The site goes on to say a fix would be to  "purchase and install a third party PCI or PCI-Express Second Generation Serial ATA controller card for your Serial ATA hard drive(s)."
    My question(s) are.
    1)Is the problem that I am trying to install a Sata ||| hard drive on a laptop with a controller that will only recognize SATA | hard drive?
    2) Or is the problem that the hard drive is an Advanced Drive Formatted hard drive and I need to buy a hard drive with out that specification?
    3) Or Should I buy a SATA controller card as WD suggests on their website and if so will this definitely allow my laptop's controller to recognize the new hard drive and proceed with the installation?
    4)Or Should I just return the hard drive and buy a SATA | non Advanced Drive Format hard drive? (question 2 basically)
    Thanks for your help!

    Hi @jasmine00 
    Welcome to the HP Support Forums.
    I certainly understand your issue with the drive upgrade. Unfortunately it is a bit of the nature of notebooks, the sacrifice of a large amount of upgradeability, in exchange for compactness and portability. Whenever a new technology comes out, older notebooks are never really going to be easy to upgrade, it at all. Normally the unit as a whole is tested with a set list of hardware, and only those items are supported.
    That being said there is this document that could be helpful with your problem.
    Preparing Advanced Format hard drives for Microsoft Windows installations on HP Business Notebook PC...
    And for your reference:
    HP Pavilion dv6000 Notebook PC Maintenance and Service Guide
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • Help Please: Big Bang-XPower: hard drive not found while installing Windows7 x64

    I bought an MSI Big Bang-XPower MB and was trying to install windows7 x64. I have a WD raptor 150GB and Samsung 1TB hard drives. Both drives show up in BIOS. SATA controller setting is in IDE.
    after I clicked at the "install" icon, a window showed up telling me that no hard drive was found. I have seen this problem before with my old MB. All I needed to do with that MB was to load a driver for the hard drive and problem solved. Does anyone know which driver (name and version, please) is the right one for this MB? I went to the MSI driver page and there are several of them. and some of them give me about 50 drives to choose from (I tried about 10 of them but neither worked).
    Also, is IDE or AHCI more appropriate for this MB with Windows7?
    Thanks for any help.

    i downloaded and unzipped the file to a USB drive. it instructed me to press F6 to load the driver, but i couldn't find this screen while I was installing windows7. at about what step does this normally show up. i can see this if i were installing xp or vista.
    anyway, when i click at the load driver with the IDE setting, nothing was found. There was a driver when i changed sata setting to ACHI, but the computer told me that was not a valid driver.
    does the drive package have to be loaded in a floppy disc?
    anyway, called tech support and was told that the xpower was one of their newest MB. and the tech rep told me that he had never heard of this problem before. he had no idea what he was talking about. Fail! lol

  • Hard drive not recognized during windows server 2008 setup

    hard drive not recognized during windows server 2008 setup

    Hi,
    Whether the hard disk is recognized in BIOS?
    Connect it to another computer to see if it could be recognzied incase the cause is the disk itself. Also please check if it is really a RAID instead of a single hard disk - a single disk should be recognized directly while RAID cannot be recognized until
    a suitable driver is installed.
    Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • 2 external hard drives not recognize by system all of a sudden

    I have 2 external hard drives, one was used as a backup with Time Machine, the other was all my music storage, including Logic Pro and Ableton files.
    This afernoon I was working on my Macbook pro with no problems, system backed up a few times. I was working on a new project in Logic. I saved the file, disconnected hard drive, went to my 2nd computer, an Imac from late 2009, plug the hard drive in, system does not recognize it. I wait a few minutes then unplug the drive, upon doing that I get a message that I've never seen before:
    "Because a USB device was drawing too much power from your computer, one or more of your USB devices has been disabled.
    To prevent damaging your computer, the USB device drawing too much power has been disabled. Other devices may have also been disabled. When you disconnect the device drawing too much power, your other USB devices will be enabled again."
    It's been a few hours, I've disconnected all the devices, I think I figured that one of the drives is faulty. My question is, why is the other hard drive not being recognized, it's not recognized on any of my 3 computers, 2 Macbook Pro's and one imac.
    Any help would be greatly appreciated as this is extremely frustrating.

    Try this:
    Intel-based Macs: Resetting the System Management Controller (SMC)
    If it doesn't help, make a "Genius" appointment at an Apple Store to have the machine tested.

  • What are the symptons of macbook pro hard drive not running fast enough

    what are the symptons of the hard drive not running fast enough

    Physically the drive will be as fast as any other of its class, and if not then it's experiencing a mechanical issue that should prompt a warning or two in the system, especially if you use a drive management tool like Disk Utility that checks the drive's built-in "S.M.A.R.T." diagnostics.
    As for "logical speed," if there are bad blocks on the drive where sectors cannot be read or written to because of a breakdown of the storage medium, then this can result in a program or the entire system crashing or hanging (generally the latter is the case), where it usually pauses for a number of seconds at a time. This is usually accompanied by messages that state "I/O Error" or other similar warning in the OS X Console (in the Applications > Utilities folder).
    Beyond this, drive formatting errors such as might happen after a crash or power outage can result in similar hang-like behavior, though this is usually not as distinct of a hanging behavior as is seen with bad blocks.
    Finally, if the drive is simply full of files or highly fragmented (not as much of a problem in OS X, but it can happen), then this can reduce access time for reading and writing files, and prevent the system from optimizing the use of RAM, which can result in overall slowdowns. Heavy drive use can also cause similar bottlenecks, but this is ususally only an intermittent issue during a time when you are performing a heavy file transfer or copying process, or other task that occupies access to the drive's index and formatting (e.g., if you check it for errors with Disk Utility, then you may see the system pause or slow down during the check).

  • External hard drive not mounting

    external hard drive not mounting

    I fixed mine by uninstalling the software that came with the harddrive such as Tuxera and reinstalled it now myharddrive works again and i did not have to delete the harddrive and reformat it.
    I tried a lot like reseting the Pram And connecting other harddrives but by unstalling the original software it works all over again. I hope this works for you because i was getting pretty frustrated myself.
    Im running a 2012 macbook pro with 10.9.3
    boom mind blown

  • I have received an error message from an attached USB hard drive (not Time Capsule) stating "Disk Name" cannot be repaired. Back up your data and reformat. I opened the Disk Utility in an attempt to repair the disk but am advised that the disk "could not

    I have received an error message relating to an attached USB hard drive (not a back up and not Time Capsule) advising that "disk name" cannot be repaired. Back up your data and reformat. When I attempted to verify the disk with Disk Utility, I was advised that the disk could not be unmounted. What can I do to repair the disk?
    Write Status is Read/Write
    SMART Status is Not Supported
    Partition Map Scheme is Master Boot Record
    HELP!
    timothy7712

    You need something stronger, such as DiskWarrior, TechTools Pro, or Data Rescue.

  • I am planning on using my time capsule as a network and essentially an external hard drive - not just back up, is this ok?

    I am planning on using my time capsule as a network and essentially an external hard drive - not just back up, is this ok?

    Most users should use the Time Capsule for backups. This assumes that "original" copies of your data are on the computer and backups of this data are stored on the Time Capsule.
    If either the Time Capsule or the hard drive on your computer fails, there are at least copies of your important data on the other drive.
    If you are asking if you can place "original" files on the Time Capsule, do you have a plan to backup those files?
    If the Time Capsule drive has a problem....and your only copy of your important data is on the Time Capsule....you will lose everything.
    If you are asking if this is OK, the answer for most folks would be "no".
    Can you clarify if this is what you are asking?

  • My external hard drive not showing up

    Hello,
    My external hard drive is not showing up on my desktop. I went to finder & preferences>general and made sure I checked "show these items" and checked hard drives. I even unchecked it because I have 2 other external hard drives. When I checked the hard drive box the other 2 hard drives appeared but the third hard drive did not. The hard drive not showing up on my desk top does show up when I double click my system hard drive & can be opened from there, but I want to see it on my desk top. Any help would be appreciated.
    Thanks

    This procedure is a diagnostic test. It makes no changes to your data.
    Please triple-click anywhere in the line below on this page to select it:
    ls -@Oaen /V* | pbcopy
    Copy the selected text to the Clipboard by pressing the key combination command-C.
    Launch the built-in Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    Paste into the Terminal window by pressing the key combination command-V. I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting.
    Wait for a new line ending in a dollar sign ($) to appear below what you entered.
    The output of the command will be automatically copied to the Clipboard. If the command produced no output, the Clipboard will be empty. Paste into a reply to this message.
    The Terminal window doesn't show the output. Please don't copy anything from there.
    If any personal information appears in the output, anonymize before posting, but don’t remove the context.

  • LaCie d2 500GB Quadra Hard Drive Not Being Seen By Time Machine

    Hello all,
    I have a LaCie d2 500GB Quadra Hard Drive Not being seen by Time Machine hooked up to my iMac via firewire 800. My iMac is running latest updates etc. Have raised a support ticket and was given the following instructions by LaCie:
    Posted: 08 November 2007 @ 00:00
    Thank you for contacting LaCie Technical Support. Make sure the drive is mounting and you can assess files on it on your 10.5 system. If you can then you will need to reformat the drive to make it compatible with time machine.
    Warning! All data on the external drive will be destroyed in this process.
    Step 1: Run Applications > Utilities > Disk Utility
    Step 2: Click on the LaCie hard drive's 'physical' entry, usually the third entry in the list
    Step 3: Click on the Partition tab
    Step 4: Change 'Current Scheme' to '1 Partition'
    Step 5: Change the name of the drive back to what you would like it to be
    Step 6: The format needs to be Mac OS Extended, with or without journaling
    Step 7: Click on the Options... button
    Use "Apple Partition Map" partition scheme on a PowerPC-based Mac.
    Use "GUID" partition scheme on an Intel-based Mac.
    Step 8: Click on OK
    Step 9: Click on Apply
    Step 10: click on Erase at the bottom of the screen, then confirm the erase.
    The drive should start to be reformatted which should take only a few seconds and show up on the desktop with a new icon. Once it has you can then use it with time machine.
    I have done all of the above and it is still not being seen. Anyone had a similar issue or got the above to actually work?
    Thanks in advance!!!!

    Ryan,
    Check drive volume name and also the Computer name. Apple released a tech note recommending that both be limited to only the characters A-Za-z0-9 (no dashes, hyphens, or other special characters.
    If you can, send the Apple System Profiler report to me at the addres in my profile. Imay be able to see something there. I have helped another user with similar problems, but with a LaCie USB drive. He got things working by repeating the recommended steps, and double checking everything.
    As others have rported, this should work, so there may be something else preventing proper operation.
    If the drive is usable from Finder, but Time Machine cannot use it, there is something related in how Time Machine is viewing the drive.
    Mike

  • Why is my External Hard Drive not showing in Aperture 3.6 Import?

    Why is my External Hard Drive not showing in Aperture 3.6 Import?
    Only my computer hard drive is and I want to import from an external drive.  I have always been able to until I updated to Aperture 3.6 and Yosemite.

    Only my computer hard drive is and I want to import from an external drive.  I have always been able to until I updated to Aperture 3.6 and Yosemite.
    I had the same problem. On the folders on the drive with the Aperture library did show in the Import panel. After I clicked the computer icon in the upper left corner of the Import panel, suddenly all drives appeared.
    You can also try to drag the folder you want to import into the Import panel, to point the file chooser to the drive.

  • I can't import my movies to work on them. They are coming from a external hard drive, not directly from the camera, its type mpeg-e (.mts)

    My movies are type MPEG-2
    I can't import my movies to work on them. They are coming from a external hard drive, not directly from the camera, its type mpeg-2 (.mts)
    What can I do ?

    1. Is your external HD connected by firewire?
    2. mpeg2 is the final compressed delivery format of a DVD, not intended for editing, and iMovie cannot handle such files, so you need to convert them first:
    For that you need mpegStreamclip:
    http://www.apple.com/downloads/macosx/video/mpegstreamclip.html
    which is free, but you must also have the  Apple mpeg2 plugin :
    http://www.apple.com/quicktime/mpeg2/
    which is a mere $20.

  • Trouble installing itunes: install to ext. hard drive not C

    I can not install itunes as it tries to install to external hard drive not internal drive C. I have followed recommendations in troubleshooting on website but no avail. Any suggestions?

    Thanks for reply. I have cleaned everything itunes off system. Have run windows install clean up but no itunes there. Still gives me error message that drive k is invalid. Drive k is my external hard drive which I have disconnected. I want it to install on c drive.

Maybe you are looking for