Hard drive not recognized after lion upgrade

My hard drive WD "My Book Studio Edition 1TB" mounts and unmounts non stop. Firewire or UBS is the same. Also with a new firmware of the disk and after a formatting. The file system is HFS+ journaled. My hardware is an iMac early 2009 24". No problems with all the other OS.
What's happen with Lion, Apple?

Hey Yelghoul,
Make sure that the drive does not have the WD encryption stuff on it. That causes the Mac to render the drive unreadable and useless. Use another computer to remove the software and any passwords on it. Then plug the drive back in. If there are no files on it, simply open "Disk Utility" under "Utilities" to reformat the drive to make it usable with Lion or other computers.
Best of luck,
@youyouxue
Lion Developer

Similar Messages

External hard drive not recognized after OSX Mavericks

My Toshiba external hard drive worked flawlessly before I upgraded to Mavericks, but now I cant access the disk. It doesnt show up on the desktop but it does show in disk utility. What do I do?!

This isn't my question, but I'm having the same problem (with a Western Digital) and thought I'd share a screenshot of disk utility for comparative purposes.
Also, Mavericks isn't allowing me to access Bootcamp

Hard drive not recognized after a brand new replacement put in 2 weeks ago!

Basically, my MBP was having the symptoms of needed a new hard drive. It was taking abnormal amounts to think and load thinks when it started up (only part of the time). I cleared all the software off of it and reloaded Mac OS just to be sure it wasnt a software issue. Apple took my computer and replaced the hard drive about 2 weeks ago (90gb, 7200 rpm). By the way the MBP is a C2D with 2 gb ram.
Immediately after getting my computer back it seemed to work fine. It has been about a week and a half since I got it back and last night trouble started. First, it wouldnt boot up all the time (id get the flashing question mark on the folder). I checked startup disk and booted it that way, no results. When it did start up, it would lock up shortly after when using applications such as safari. I then booted it to the system disk and performed the first aid functions on the disk... no results. And now, the next morning, when i boot to the disk, the hard drive itself is not even recognized under disk utility??? So basically, I cant reload OS again because I cant see the installation disk. Is this a a hardware issue even though I just replaced the hard drive?
what do i do??

Hi MBPrunner;
It appears you have the misfortune of infant mortality whereby a bring new part fails in a short period of time. This does happen. I have seen it numerous time in my years of server support at IBM. My suggestion is take it back it back to Apple with all of your paperwork. They should make good on it.
Allan

External Hard Drives not Mounting after Yosemite Upgrade

I've just upgraded to Yosemite, and none of my external (USB) hard drives are mounting (they don't even appear in Disk Utility).
Any ideas?

MacBook Pro 2009. 250 SD, HD 8Gb Ram.
I have had this issue for about a year...with no resolve!
Apple and the User community have not been able to solve issue.
I have had to work around it since the Oct 2013 Mavericks upgrade which “killed” (rendered unmountable) both my USB and Optical drives.
Hundreds of replies and remedies have not corrected my issue. Hundreds of replies stating that if there was a global issue it would of been fixed by Apple, not true. And dismissive replies stating that there must be a hardware issue are very discouraging.
So now, hoping to help the voiceless masses, I'm forced to share my experience.
As I stated, I have been having the issue since one of the Mavericks upgrades. The upgrade rendered externally attached drives unmountable...They are all seen in Disk Utility. They are just not mountable. Regardless of the flavor of the disk format, either Mac or PC, they are found, seen and refuse to mount. I can see them using Terminal commands, I can see them in System Report. I can reset all the memory I want...turn it off, reset, sleep, turn on, restart...NOPE...And the optical drive takes in disks but ejects them after an attempted mounting. Keep in mind, there are no physical issues with either USB or optical drives.
So now...I have had enough and need to correct the issue or buy a new equipment - starting to get into software development and need working equipment!!!
For the past month, I have been visiting the Apple store to assist in my issues...Back Story: I'm an IT Field Tech for the largest department store in the country and I have the good fortune of dropping in the Apple store anytime I want...The Geniuses booted the MB with a bootable image of Mavericks, and the USB and Optical drives WORKED fine...So, after I had stumped the Geniuses with my problems, we agreed that we would attempt to format and re-image the MacBook...Fine, do it, it's backed-up, how you ask? - Via my wireless My Book Live 3T drive, which only took 24 hours to backup, AKA Time Machine!
Great news! The re-image of Mavericks proved to work! I WAS able to mount external drives attached! How is that possible? Don't know, don't care! It just worked! So happy!
But wait! I then took the laptop home. Connected to my WiFi, to update Mavericks to the latest version...Good so far! Then it came time for a Time Machine restore, AKA Migration Assistance restore...So, I proceeded to migrate data back to my MB via wireless drive, good so far, booted in Migration Assistant, and I chose to restore everything except the network files, thinking that may be an issue...22 Hours later, the MB migrated without issue...all apps and personal files had migrated! YAY!
BUT NOW THE USB AND OPTICAL DRIVES FAILED TO MOUNT!!!
Great now what? I know, I will just re-image and start again...WAIT, I don't have a Mavericks Install Disk, no problem, I will just create a bootable USB drive with the Mavericks Install Image I downloaded onto my MB this month...NO YOU CANNOT, because you have no use of the USB drives!...And, Apple stopped making OS CDs back in 2009...Oh, and that wouldn't of done me any good, because the optical dive was unusable, anyway!
SO, back to the Apple store with my head hanging! At this point, Yosemite came out the previous Thursday, so no more Mavericks images, great! Perhaps the new OS will alleviate my nightmare!!!!...So, they re-imaged my Mac with Mavericks, drives worked again! SO, I took my MB home and attempted to download the new OS, Yosemite...which only took 2 days due to the amount of traffic on Apple's servers!...Anyway, Yosemite finally installed without out issue! Drives still worked! And so, I shutdown and restarted the system...No issues, USB and optical drives worked beautifully! Yay, Yosemite!...Fixed all my troubles!!!...Not so fast...
And so, I, again, attempted to do a Time Machine restore, via WiFi, this time it took 24 hours to restore...AND it worked! All apps and personal files transferred without issue, So happy! Put the laptop in Sleep and left it home and went to work! Came back from work, tested the system without issues. Rebooted...USB and Optical drive are NOT MOUNTABLE!
So now, what is the file that the restore keeps pushing to my MB that kills the USB and optical drives?
I would just stop restoring from a Time Machine backup, but the only way to get into the TM image is to use Migration Assistant. I cannot view the date in time of the image in TM's Star Wars time line. So, I'm forced to back up everything from the image in Migration Assistance. Not sure that it being an encrypted image has anything to do with it...
...Regardless, what is being “restored” to the MB that continues to configure the OS in such a way that makes all external drives unmountable...keep in mind, my external keyboard, hub and mouse are usable via USB.

Hard drive not recognized AFTER installing leopard

So I installed Leopard on my 12in Powerbook G4, having the usual problem of non-recognition of my hard drive (from a third party) but was able to install Leopard after fiddling with disk utility.
Now the computer will not recognize the hard drive after I restarted it. I've tried rebooting holding down the option key and selecting the hard drive and it still didn't recognize after restarting (it shows a prohibit sign). Also tried booting in single-user mode but it keeps waiting for the root device forever.
Has anybody had a similar problem?

Unplugging worked!!!
I have no idea what PRAM is but someone said that unplugging your computer resets it so, I thought I'd give unplugging a shot. So, I shut down my computer and unplugged it. I also unplugged the power on the HD. (because I wasn't sure which one they were talking about.)
Anyway, I went away for about five minutes.
I came back plugged in the HD power first. Then, I plugged in the power cord for the computer and turned it on.
As soon as I logged in I was asked if I wanted to use my external HD for Time Machine backups.
I saw the icon for the HD on the Desktop where is belongs. I can open the drive and access the files with no problem.
Try this if you haven't yet.

External hard drive not recognized after power outage

After a power outage last night my WD external hard drive is not showing up. The power light is on on the drive, the DVR is working normally, except my external drive is not showing up. I unplugged power from the DVR and restarted it, but no change.

I have a 2G Samsung drive in Rosewell external encloser running for over a year. Two times have lost power and DVR would not recongize external drive. The procedure I used was to reboot twice via menu>settings>customer support>in home agent>reboot STB. Mine required two resets, the first reboot looks like DVR recongizes drive but does show as available but second reboot shows disc activity during last part boot up of box then external would show with all recordings and normal operation. I have not lost any recordings.

Now, USB External Hard Drive Not Recognized after 10.6.8 Update

My external Hard Drive is not recognized on start up. I have to unplug it and plug it back in for it to be recognized.
All this since 10.6.8 updated today.
I'm a fool for updating the same day.
This has happened before and I always forget the bugs in the software when it first comes out.

Alright, I'm gonna go ahead and close this thread. I found out the solution to my issue. Turns out it was a problem with a system file I changed right before installing. The error only occurred on a restart... the required 10.6.1 reboot was the first reboot since the change, so thus it looked like the culprit.
If you want a more thorough explanation of my problem (highly HIGHLY doubt it's gonna help you guys out), check this thread --> http://forums.appleinsider.com/showpost.php?p=1480362&postcount=8
Sorry for the trouble!

Lacie External Hard Drive Not Recognized After It Previously Was

I have a 1 Tb Lacie Big Disk External Hard Drive that I have used for a couple years now. I have a Mac Pro, an iMac and a G5 computer that I have previously used with it. After I transferred it between computers yesterday suddenly it will not show up on any of the computers. I have tried different cables and inputs, computers, other hard drives with the same cables (they worked), restarting the computers, etc. The hard drives powers on like normal and you can hear it running, the blue light comes on in the front, but it never gets the disk loaded on the computer. There is a "auto/on/off" button on the back that I have tried switching between but nothing seems to work. Please let me know if this is a common problem and any way to get it to work as I would prefer not to lose the information on the hard drive, especially when it seems to be functioning just fine aside from not appearing on the computer.

Even backups need backups too.
And a 'good' case is one where you can pulll the drive out and pop it into your Mac pro drive bay.
power supply bricks are known issue.
Mac OS updates that affect those models.
LaCie almost by their own invented the term and idea "reset firewire bus" routine after all.
Years and you can assume not forever but eventually it could and will fail.
I'd pick up a "spare" or replacement unit, one with eSATA/FW800/USB3
http://www.macsales.com/firewire
CallDigit 2 x SATA plus 2 x USB3 $139 - USB3 card and interface works better even on legacy (how long and old is USB2 now?) USB drives.

WD external hard drive not recognized after improper eject

I have a WD Passport external hard drive that I've been using for a while with my MacBook Pro. The cord got yanked, causing the drive to improperly eject. Now my computer isn't recognizing the HD. Help! Of course EVERYTHING important is on this drive!
I tried plugging it into a Mac desktop, which also did not recognize the drive.
I plugged a different Passport into my MacBook Pro, and it was recognized, so I know it's not the USB Port that's causing the problem.
I used the cord from the HD that mounted with the problem HD. Didn't mount with the new cord. So I know it's the passport that's causing the problem, not the MacBook, not the USB port, not the cord.
I ran the disk utility, and the HD does not appear...It is powering up though- the light on the HD is lighting up. Oh please help!
Did I kill my disk? Of course I just moved my entire iPhoto library to this location, and I haven't backed it up yet....

No. It may just require a 00 Phillips driver depending upon the enclosure. Do the swap on a towel so that the little screws don't bounce away from you. You will have to pull the HDD out from the connecting plug. Do it in a straight line,don't bend it, and you may have to slowly increase pressure to get it out of the connecting plug.
It's not rocket science.
Ciao.

External Hard driver not recognized after force eject while Mac was asleep

So my Samsung hard driver had force ejected itself when my Macbook pro was asleep, it cant be recognized anymore. It doesn't show up under utilities, however it does show up under System report.
I've tried to plug it onto my desktop, however the system had failed to install the software to run the hard drive, yet again it does show up under properties.
Help please???!!!

No. It may just require a 00 Phillips driver depending upon the enclosure. Do the swap on a towel so that the little screws don't bounce away from you. You will have to pull the HDD out from the connecting plug. Do it in a straight line,don't bend it, and you may have to slowly increase pressure to get it out of the connecting plug.
It's not rocket science.
Ciao.

External hard drive not recognized after time machine locked up

I was backing up to an external hard drive (300GB Western Digital) and time machine locked up. I had to shut down the computer and restart. Now the external hard drive does not show up on the desktop?
I can see it in disk utility but I am not able to mount or unmount the disk, I keep getting an error that the disk is in use. I tried to erase/reformat the disk and no luck.
Any suggestions?
Thanks for the help

KTM450rider wrote:
Do I need to boot from the install DVD?
this is often the easiest and eliminates any "busy drive" problems. what's wrong with booting from the install DVD? takes a couple of minutes.
My main hard drive is OK... the drive that I am having problems with is an external hard drive that I was using to back up my lap top. I just want to get the external drive reformatted, but disk utility will not erase it. I get an error that disk utility shut down, "please check the drive and make sure that the drive is not in use or programs are still running"
Is their a way to do a hard or forced reformatting of an external hard drive, I don't care about the information on the drive
I also tried disk warrior to recover the info on the disk and all it does is crash my mac pro????
Thanks again for the help

Micronet 500 GB Hard Drive NOT recognized after 1 year of seamless use

Micronet 500 GB Hard Drive
Firewire 400 and 800.
I always use the 800. I plugged it in today and the hard drive start-up fine as usual. Without even looking on the desktop I opened Final Cut and it told me it could not locate my scratch disk (I always use the 500gb for FCP). I've tried different cable, and using the Firewire 400 instead of the 800. I don't know what to do, I had wanted to put some things on video for christmas and I don't have space on my startup disk to put video (hence the need for the external). Please someone help me, I don't know what to do. I'm terrified of the thought that my external could be dead or something like that. Please help! Thanks, Mike!

Most persons that have installed an SSD that was smaller than the factory drive have been unable to use any HP Recovery Media with the SSD.
As an alternative, if you can still read the 25-digit Windows product key on the Microsoft COA affixed to the bottom the computer, you can install Windows 7 Home using this key. Please see "How to Install Windows 7 Without the Disc" for instructions on how to download Windows 7, create the installation media, and install Windows 7 using the 25 digit product key from the Microsoft COA on your computer. Please note that this installation will not have any of the HP customizations or HP value-added that was original installed on your computer. Also note that you will need to download and install most of the drivers from the HP G62t-350 CTO Notebook PC Drivers page.
Links to Windows 7 SP1 can be found HERE and HERE.
Direct link to the Windows 7 USB/DVD Download tool. Use this tool to create a bootable DVD or USB Flash Drive from the Windows .ISO
If you have any further questions, please don't hesitate to ask.
Please click the White KUDOS "Thumbs Up" to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Usb hard drive not loading after security update

usb hard drive not loading after security update
I can't seem to find any other posts about this problem.
I have three external hard rives connect by a USB hub to my iMac.
Problem is that if I turn on the hard drive(s) AFTER start up I get a message that the drive either was not recognized by the OS or that it was ejected unexpectedly.
I get the same issue but not all the time if I turn them on before I boot the iMac.
I used the disk drive utility to "repair" the drives but they always come back as "probably ok".
If I restart the iMac with the drives connected (on), it seems to work but not all the time.
A bit annoying as I am wondering if the drives are OK or not.
I don't always need the drives as they are for backing up images from my camera using Apreture.
This all began after i did the latest security update.
is the update to blame?
mahalo.

Yes, you can still use those instructions to reset the PRAM.
You said that you booted to your install disk and that your primary drive did not show up at the Select a Destination screen? That usually means that the computer is either not recognizing your partition, or it's not recognizing the hard drive itself.
Start with this article and follow all the steps even if you already tried them. I suspect that you'll get to step 4 and you'll end up having to call Applecare. If you haven't done those steps, they're most likely going to make you do them anyway, so you might as well get them done before the call.

Hard drive not recognized during windows server 2008 setup

hard drive not recognized during windows server 2008 setup

Hi,
Whether the hard disk is recognized in BIOS?
Connect it to another computer to see if it could be recognzied incase the cause is the disk itself. Also please check if it is really a RAID instead of a single hard disk - a single disk should be recognized directly while RAID cannot be recognized until
a suitable driver is installed.
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Advanced Format Hard Drive not recognized by HP DV6000 Controller

Hello,
I have an HP DV 6000 laptop (6276 I think, I'm at work can't check) that came preinstalled with a Western Digital 160gb 1.5gb/s 5400 RPM drive (Vista) that failed a couple of weeks ago. So i bought a Western Digital 750 GB WD Black SATA III 7200 RPM 16 MB drive to replace it. I read about people having some problems with Advanced Drive Format hard drives not being recognized by their controller, but also read that depending on the controller and specific Dv6000 model laptop they had-one wouldn't run into problems.
Well sure enough, when attempting to install Windows 7 I received the error that the hard drive was not detected. After researching online I came across an article on WD's site that noted
"Our SATA II hard drives use autospeed negotiation. This enables our SATA II drives to automatically detect the motherboard data transfer rate, making it backward compatible with SATA I data transfer rates. However, some older SATA I controllers are unable to support autospeed negotiation and cannot recognize the drive. This “drive not detected” condition occurs when a chipset is incapable of correctly negotiating the data transfer speed with a SATA II hard drive."
my drive is a SATA ||| but I'm pretty sure it's the same problem. The site goes on to say a fix would be to "purchase and install a third party PCI or PCI-Express Second Generation Serial ATA controller card for your Serial ATA hard drive(s)."
My question(s) are.
1)Is the problem that I am trying to install a Sata ||| hard drive on a laptop with a controller that will only recognize SATA | hard drive?
2) Or is the problem that the hard drive is an Advanced Drive Formatted hard drive and I need to buy a hard drive with out that specification?
3) Or Should I buy a SATA controller card as WD suggests on their website and if so will this definitely allow my laptop's controller to recognize the new hard drive and proceed with the installation?
4)Or Should I just return the hard drive and buy a SATA | non Advanced Drive Format hard drive? (question 2 basically)
Thanks for your help!

Hi @jasmine00
Welcome to the HP Support Forums.
I certainly understand your issue with the drive upgrade. Unfortunately it is a bit of the nature of notebooks, the sacrifice of a large amount of upgradeability, in exchange for compactness and portability. Whenever a new technology comes out, older notebooks are never really going to be easy to upgrade, it at all. Normally the unit as a whole is tested with a set list of hardware, and only those items are supported.
That being said there is this document that could be helpful with your problem.
Preparing Advanced Format hard drives for Microsoft Windows installations on HP Business Notebook PC...
And for your reference:
HP Pavilion dv6000 Notebook PC Maintenance and Service Guide
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Hard drive not recognized after lion upgrade

Similar Messages

Maybe you are looking for