Hard drive not recognized in HDD bay.

Randomly, my laptop gave me the spinny pinwheel of death when I opened it, and upon restart, I got the good old folder with a "?" indicating there was no OS. Naturally, I booted up in network recovery, and low and behold, my SSD was not in the Disk utility list. I made an adjustment some time ago where I removed my optical drive, and installed the old HDD that came with the computer in it's place. I switched the drives, so that the SSD was where the optical drive should be, and the HDD in the drive bay. Upon startup, the computer booted up as usual from the SSD, and the HDD was not recognized. So from there I conlcuded that both the SSD and HDD are working correctly without failure. After putting the drives back where they originally were (HHD in optical bay, and SSD in Drive bay), and I booted up holding the option key, The SSD and recovery drive were there, but I received a prohibited sign (circle with slash) after a minute. Now it is not recognizing the drive again. I'm not sure whats going on, anyone hav any input?
Thanks

You have a faulty hard drive to logic board cable. Replace that and you should be fine and the drive put in the main bay should show up.

Similar Messages

Hard drive not recognized during windows server 2008 setup

hard drive not recognized during windows server 2008 setup

Hi,
Whether the hard disk is recognized in BIOS?
Connect it to another computer to see if it could be recognzied incase the cause is the disk itself. Also please check if it is really a RAID instead of a single hard disk - a single disk should be recognized directly while RAID cannot be recognized until
a suitable driver is installed.
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Advanced Format Hard Drive not recognized by HP DV6000 Controller

Hello,
I have an HP DV 6000 laptop (6276 I think, I'm at work can't check) that came preinstalled with a Western Digital 160gb 1.5gb/s 5400 RPM drive (Vista) that failed a couple of weeks ago. So i bought a Western Digital 750 GB WD Black SATA III 7200 RPM 16 MB drive to replace it. I read about people having some problems with Advanced Drive Format hard drives not being recognized by their controller, but also read that depending on the controller and specific Dv6000 model laptop they had-one wouldn't run into problems.
Well sure enough, when attempting to install Windows 7 I received the error that the hard drive was not detected. After researching online I came across an article on WD's site that noted
"Our SATA II hard drives use autospeed negotiation. This enables our SATA II drives to automatically detect the motherboard data transfer rate, making it backward compatible with SATA I data transfer rates. However, some older SATA I controllers are unable to support autospeed negotiation and cannot recognize the drive. This “drive not detected” condition occurs when a chipset is incapable of correctly negotiating the data transfer speed with a SATA II hard drive."
my drive is a SATA ||| but I'm pretty sure it's the same problem. The site goes on to say a fix would be to "purchase and install a third party PCI or PCI-Express Second Generation Serial ATA controller card for your Serial ATA hard drive(s)."
My question(s) are.
1)Is the problem that I am trying to install a Sata ||| hard drive on a laptop with a controller that will only recognize SATA | hard drive?
2) Or is the problem that the hard drive is an Advanced Drive Formatted hard drive and I need to buy a hard drive with out that specification?
3) Or Should I buy a SATA controller card as WD suggests on their website and if so will this definitely allow my laptop's controller to recognize the new hard drive and proceed with the installation?
4)Or Should I just return the hard drive and buy a SATA | non Advanced Drive Format hard drive? (question 2 basically)
Thanks for your help!

Hi @jasmine00
Welcome to the HP Support Forums.
I certainly understand your issue with the drive upgrade. Unfortunately it is a bit of the nature of notebooks, the sacrifice of a large amount of upgradeability, in exchange for compactness and portability. Whenever a new technology comes out, older notebooks are never really going to be easy to upgrade, it at all. Normally the unit as a whole is tested with a set list of hardware, and only those items are supported.
That being said there is this document that could be helpful with your problem.
Preparing Advanced Format hard drives for Microsoft Windows installations on HP Business Notebook PC...
And for your reference:
HP Pavilion dv6000 Notebook PC Maintenance and Service Guide
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Memory modules and hard drive not recognized

I removed and reinserted the factory installed Satellite L505D-LS5007 laptop hard drive and memory modules just as practice for installing a hard drive upgrade and an 8GB memory upgrade. The problem is obviously with the memory and not with the hard drive.
After the first practice try, one memory module was recognized. Also for a few seconds after the first practice try, I ran the PC with the battery installed, but no memory installed. I did not look in the User's Guide first to see that I should have removed the battery before removing the memory.
Now the System Indicator Lights for the HDD Activity and Memory Card Reader do not light up. The PC turns on and the display is solid black with no messages.
Before buying new memory modules, what possible ways might there be to get the PC to recognize the factory installed memory modules and hard drive again?
Solved!
Go to Solution.

When troubleshooting, I always change one variable at a time. I would hate to miss a solution by being in a hurry. In this case, you may have damaged either the RAM or the RAM slot. I would stick with the Toshiba specifications for the RAM, making sure it is the correct size, speed and type recommended. I also recommend that when you replace the RAM that both modules be from the same manufacturer, size, and specification. Try one RAM module in one slot and then the other. And then try both RAM modules in both slots. After the testing you should be able to figure if this is a RAM problem or a RAM slot problem.
In the case of hard drives, the real test is whether or not the Bios sees the hard drive. If the Bios doesn't see the hard drive, it's not going to work. The Bios should see the hard drive whether or not the hard drive is partitioned, formatted or has data on it. My experience has been that many Toshiba laptops will work fine with larger capacity hard drives provided they are the same speed in RPMs, have the same interfacing connection and physically the same size.
Again, prior to doing any work on your computer, make sure that both the AC power has been disconnected and the battery has been removed. Be careful out there. A blown repair job by a non-Toshiba tech is NOT covered under warranty.

New WD Scorpio Black 750GB hard drive not recognized

Hey guys,
I've purchased a WD Scorpio Black 750GB hard drive for my newly acquired MacBook Pro 5.5, 2.26 GHz Intel Core 2 Duo. The hard drive is installed (internal) but not being recognized by disk utility. Browsing on Google, I've found this to be a common occurring problem but as there were no direct solutions, I'm posting this in case anyone has any solutions to this issue.
I've reset the PRAM/ NVRAM with no avail. Any assistance would be greatly appreciated.
Cheers

Your response is not 100% clear to me.
Have you actually installed the WD and Seagate HDDs in the MBP or just connected them while in an external enclosure?
When you put the original HHD back in the MBP, it is recognized in Disk Utility but cannot be repaired? Is that the case.
Have you tried to put in the original Installation disk and has the original HHD been recognized and/or one of the other HDDs in an enclosure been recognized?
Ciao.

MBP Late-2011 hard drive not recognized

Okay, so last November 2012, not even a year after I bought my MBP, it just froze and wouldn't respond to anything. All it showed was the rainbow loading circle and the computer crashed. I brought it to the Apple store and the person behind the Genius bar said that it was a hard drive problem and he replaced it. However, ever since then, I noticed that my mac has been running very slow and programs would take a lot longer to load.
5 months later, my computer is having problems again and one time when I turned it on, it just showed a blinking folder with a question mark. I know this means it can't find the system software. I brought it to a friend and he tried to fix it first by using the OS X system software disc but that didn't work. Then he thought the problem was the hard drive cable so I bought a new one and when he replaced it, my hard drive still isn't recognized. At this point he thinks it's something with the logic board or something since nothing seems to be working. Right now, all I'm doing is connecting my hard drive to the USB and using booting from there. Everything else is working fine. Does anyone have any suggestions as to what I can do? (btw, I don't have AppleCare)
Thanks.

The good news is that it is not the logic board, other wise the MBP would not function at all. The symptoms that you describe are a strong indication that the internal HDD connection is faulty.
As mentioned before, have the technicians at the genius bar look at it and if I am correct, they should be able to install a new cable and allow you to use the MBP with the HDD inside the MBP. This is not an expensive repair.
It is also possible that the replacement cable that was installed earlier was not done correctly.
Ciao.

Hard drive not recognized in disk utility

I'm trying to replace the hard drive in my MacBook Pro , the old hard drive was not recognized in disk utilities after the computer crashed .After installing a new hard drive and booting from the original Mac OS install DVD,( leopard?) the new hard drive is not recognized either ? Help

It may be the internal connecting cable that is the problem. If you can install the new HDD in an enclosure, connect it to the MBP, then see if you recognize it using the OSX installation disk. If so, the internal connector should be replaced.
Ciao.

T43 Hard drive not recognized unless replugged

It's a T43 with a 100GB FUJITSU MHV2100AH hard drive. Last night the blue screen came on. Upon rebooting, it displays "Operating System not found", and the hard drive is no longer recognized. The problem persisted, until I unplugged and re-plugged the hard drive. Then the system booted normal. Today, the problem came up twice, again, and unplugging still does the trick. Hard drive has passed Ontrack EasyRecovery Full Diagnosis with minor problems (a few bad sectors), but it's not likely that the bad sectors are causing the problem, is it? Anybody has an idea what is wrong here? Thanks!

Unfortunately, I can't find where he posted that, see I also own a T42p with ATI graphics, it's been running great ever since I bought it from him (knock on wood), he commented about this symptom somewhere and I took it as a way to tell when mine would be facing the same fate (I hope that moment never comes ).
Since motherboard replacement is an expensive assumption, therefore I would first suggest you to run a complete diagnostic test through lenovo PC Doctor's bootable CD for DOS:- http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-56222
If your ThinkPad passes all tests with flying colors, then try borrowing or buying a new HDD (2.5'' ATA/IDE notebook drive), if the new HDD does the same then probably your motherboard is failing.
Following links contain some known symptoms of motherboard failure on T4x ThinkPads, check if yours exhibit any:-
http://forum.thinkpads.com/viewtopic.php?p=492633#p492633
http://forums.thinkpads.com/~thinkpad/forum/viewtopic.php?p=584727#p584727
Hope this helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

New x1 carbon: portable hard drive not recognized

Hi everyone,
I found this issue really annoying, let me show you the detail
1.Both usb ports work well after I reset my computer.(USB flash drive or USB portable hard drive can be used at anytime)
2.After I installed all the drivers provided on the website, this issue came out
3.If you plug in the USB flash drive, both ports work well at anytime
4.If you plug in the USB hard drive, most of the time system cannot recognize it
5.If you plug in the USB hard drive right after restart, the system will recognize it, but after a while, it can't
6.One interesting fact: if you plug in a USB falsh drive first, then unplug and plug in the hard drive, the hard drive then can be recognized...And the other unused USB port will not recognize anything...
7.When the system cannot recognize my USB hard drive, you can hear the HDD is working but you cannot find this device in device manager, however, when you unplug it, there will be a warning tone just like you unplug any other devices.
8.I have to restart Windows and plug the hard drive immediately to use it, or after few minutes Windows will not recognize it unless you restart again, sometimes I have to restart more the 3 times.
P.S. Both the USB ports are fine, both my flash drive and hard drive are fine, this issue happen right after I installed all the drivers. The hard drive is 2.5'' so do not need extra power. My BIOS is the latest. And I trived set the "USB 3.0 only" mode in the BIOS, doesn't work
Thank you for your help!
Moderator comment: Please refrain from bumping your thread(s) / post(s) more frequently than 3 days. Doing so, unfairly, pushes other members' threads downwards. Bumping post(s) removed.

are your portable hdd connected to two usb? one for data and one for power?
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

External hard drive not recognized in Finder or Disk Utility

Two weeks ago, my 2007 black Macbook stopped recognizing the hard drive. I was told by some IT friends that the controller had likely failed and I needed to purchase a new laptop. I removed the hard drive and placed it into an enclosure (turning it into an external hard drive) and hooked it up to a new Macbook Pro which I purchased a couple days ago. The external hard drive did not show up in Finder or Disk Utility but the light on the enclosure was on and it was making a very soft whirring noise and got warm after a few minutes. I usually backed up the hard drive but, of course, hadn't done it in a couple of weeks before it died so everything I worked on in that time is lost to me at the moment. I'm trying to avoid paying tons of money for a data recovery service so any advice would be greatly appreciated! Thanks!

That whirring noise might be due to physical damage on the disk. I know data recovery services are costly but that remains only the solution for damaged HDD. You can get latest quotes on services from different dealers. Proceed only when your data is very important to be recovered.

WD external hard drive not recognized after improper eject

I have a WD Passport external hard drive that I've been using for a while with my MacBook Pro. The cord got yanked, causing the drive to improperly eject. Now my computer isn't recognizing the HD. Help! Of course EVERYTHING important is on this drive!
I tried plugging it into a Mac desktop, which also did not recognize the drive.
I plugged a different Passport into my MacBook Pro, and it was recognized, so I know it's not the USB Port that's causing the problem.
I used the cord from the HD that mounted with the problem HD. Didn't mount with the new cord. So I know it's the passport that's causing the problem, not the MacBook, not the USB port, not the cord.
I ran the disk utility, and the HD does not appear...It is powering up though- the light on the HD is lighting up. Oh please help!
Did I kill my disk? Of course I just moved my entire iPhoto library to this location, and I haven't backed it up yet....

No. It may just require a 00 Phillips driver depending upon the enclosure. Do the swap on a towel so that the little screws don't bounce away from you. You will have to pull the HDD out from the connecting plug. Do it in a straight line,don't bend it, and you may have to slowly increase pressure to get it out of the connecting plug.
It's not rocket science.
Ciao.

External Hard driver not recognized after force eject while Mac was asleep

So my Samsung hard driver had force ejected itself when my Macbook pro was asleep, it cant be recognized anymore. It doesn't show up under utilities, however it does show up under System report.
I've tried to plug it onto my desktop, however the system had failed to install the software to run the hard drive, yet again it does show up under properties.
Help please???!!!

No. It may just require a 00 Phillips driver depending upon the enclosure. Do the swap on a towel so that the little screws don't bounce away from you. You will have to pull the HDD out from the connecting plug. Do it in a straight line,don't bend it, and you may have to slowly increase pressure to get it out of the connecting plug.
It's not rocket science.
Ciao.

Yoga 2 Pro Hard Drive not recognized

I got my Yoga 2 Pro as a Christmas present and have had issues with the computer recognizing the hard drive every time it boots up or enters sleep mode (and this is after the 1 initial boot up where I didn't have to enter the BIOS). Not sure if this is a bios or hardware issue, but I can get it booted after entering the BIOS, changing various (seemingly random) settings (UFEI/Legacy support usually) to get the computer to even recognize that it has a hard drive installed at all. Once it does boot, as long as it doesnt sleep or shut down, it'll continue to work, leading me to think this is some sort of BIOS issue. Has anyone been able to resolve this issue without the hassle of returning it to Lenovo an getting a whole new one? The computer is great, when it boots up, but this is extremely disappointing/frustrating to have to enter the BIOS every single time I want to turn the computer on to use it!

@Lenovo Support - Please respond to this issue.
SO MANY PEOPLE HAVE FACED THIS ISSUE & ARE STILL FACING - BUT NO RESPONSE FROM LENOVO SUPPORT...... !!!!

Lacie 250GB External Hard Drive NOT RECOGNIZED

HELP! My Lacie External HD that I've had for several years and holds a lot of my files is no longer being recognized on my MacBOok Pro. It used to recognize it instantly when I plugged the USB cable to the USB Port - now, nothing. The Lacie light is on, but my laptop isn't reading it at all. What's going on??? I did a disk utility - it's not showing up there at all either. Is it due to a software update? Don't get me started on losing out on using my entire Dreamweaver/Flash Studio MX 2004...
ALSO, I notice my iPhone is not being recognized in iPhoto anymore either. It is recognized in iTunes. And yes i've heard many folks say email photos should be removed, which i have done so and still nothing!
HELP PLEASE!!!

Are other USB devices working normally, Eric?
If so, the most likely cause is that either the bridge or the drive itself in your external enclosure has failed (assuming you have tried a different cable)
No, it is most unlikely to be due to a software update. With an old external drive like yours the most likely explanation is that it has simply failed. If it is the bridge, rather than the hard drive itself, that has died you may be able to remove the HD from the LaCie enclosure, put it in a different enclosure, and recover your stuff. In some cases, too, a drive light will illuminate when the drive is connected to the computer, even if the power supply to the drive itself is faulty. You might want to contact LaCie to see if they have any advice to offer about such situations.
Have you tried the drive on another Mac or another drive on this Mac? THis would immediately narrow down the location of the problem, of course.
Cheers
Rod
Message was edited by: Rod Hagen

X79A-GD45 Secondary Hard Drive Not Recognized

Hi,
I actually had this problem from the very beginning when I bought it a year ago, but it wasn't such a big deal because I worked around it (I was needing to clone my hard drive - I made a back up on an external hard drive, removed the source drive, installed the new hard drive, and restored the backup to it). But, I'm in need of cloning my hard drive again, and it's very inconvenient to do it this way, especially its size has grown since. So, I'm hoping that I can find a solution. The problem is that, it just doesn't recognize an additional hard drive period. I've tried connecting it to a different SATA slot, no luck. I read some online suggestions about changing management setting (AHCI, IDE, RAID), no luck. It doesn't show up in Windows (not even under disk manager). It doesn't show up in Parted Magic. It doesn't show up in Acronis True Image bootable CD. So, I've concluded that it has to be something with the M.B.
I'd appreciate any help/suggestion. Thank you.
GT

What OS are you using? HDD properly formatted? SATA II drive or SATA III? What ports have been tried? All SATA controllers in the BIOS enabled?

Hard drive not recognized in HDD bay.

Similar Messages

Maybe you are looking for