Hard reset on NAS NSS 326

Hi,
can someone confirm if this will allow access to previously encrypted volumes?
We have an nss326 which has the encrypted password stored for when the nas boots up and unlocks the volumes automatically. The previous administrator set the password and nobody knows what it is. We need to change the encryption key and keep the data.
Is the hard reset the best way to achieve this?
thanks

Marc,
I would first back all data you wouldn’t want to lose since the volume is unlocked now. Instead of a hard reset we can attempt a reset of admin password. Administration guide: PG- 39
http://www.cisco.com/en/US/docs/storage/nass/csbcdp/smart_storage/admin/guide/NSS32X_Admin_Guide_OL21155_v1.5.pdf
Reset Network Settings and Password
You can restore the network settings and password for your NAS device using the
reset button located on the back panel. The NAS device should be powered on for
this procedure. Using a paper clip, press the reset button for 3 seconds, until the
NAS beeps.
The following settings are reset to default:
• System administration password: admin
• Network settings:
- Obtain TCP/IP settings automatically via DHCP
- Disable Jumbo Frame
- System management port - 8080
• System tools: IP filter settings - Allow all connections
• LCD panel password: (blank)
This 3 second reset should only clear out these fields but back up all data as a precaution.
Hope this helps,
Jasbryan.

Similar Messages

NAS NSS 326 Reset Issue.

Hi peeps
Have a little issue with a Cisco NAS NSS 326 Smart Storage 6 bay - with RAID 5 over 6 disks.
Apparently there were some funny business with the performance with the device so someone reset the device from the button on the back.
I've been ask to get everything working but I've bumped into a little problem.
The DHCP address the device pick up is 10.2.7.127, so I open up a web interface and hop on that address and configure password, time etc.
When it comes up to step 6 I've tried selecting "Do not set disk configuration" and RAID 5, then on the finish window to start installing it advises it'll format all disk to continue!!!
We have a lot of data (9GB or so)
Is it possible to continue in any way without clearing the data we have on it? or map it somehow to recover the data?

Marc,
I would first back all data you wouldn’t want to lose since the volume is unlocked now. Instead of a hard reset we can attempt a reset of admin password. Administration guide: PG- 39
http://www.cisco.com/en/US/docs/storage/nass/csbcdp/smart_storage/admin/guide/NSS32X_Admin_Guide_OL21155_v1.5.pdf
Reset Network Settings and Password
You can restore the network settings and password for your NAS device using the
reset button located on the back panel. The NAS device should be powered on for
this procedure. Using a paper clip, press the reset button for 3 seconds, until the
NAS beeps.
The following settings are reset to default:
• System administration password: admin
• Network settings:
- Obtain TCP/IP settings automatically via DHCP
- Disable Jumbo Frame
- System management port - 8080
• System tools: IP filter settings - Allow all connections
• LCD panel password: (blank)
This 3 second reset should only clear out these fields but back up all data as a precaution.
Hope this helps,
Jasbryan.

OS X Lion and NSS 326

I've got a Cisco NSS 326 NAS and have recently run into a problem with OS X Lion Developer Preview and authentication to the NAS. When connecting to the NAS over AFP as guest I can access the NAS just fine. However, when I try and authenticate I get an error that reads:
"The version of the server you are trying to connect to is not supported. Please contact your system administrator to resolve the problem."
I've read on another site (http://trick77.com/2011/02/25/afp-broken-linux-based-nas-mac-os-x-lion-10-7) that this has to do with the version of AFP that is running on the NAS compared to the new version that OS X Lion is using AFP 2.
Does anyone have a solution to enable the NAS to support AFP 2 or are there any plans to support this from Cisco any time soon?

Hi all NSS32x owners,
Like you all, I bought a Storage Solution from Cisco, personally hoping that Cisco would be better in supporting us than the OEM they bougth the NSS32x line from.
Until now I have been disapointed over and over.
They opened a discussion about what should be implemented in the Cisco versions of the NAS'ses but so far no real addition of any value.
Now we are facing the problem with OS X Lion's TimeMachine incompatability, which could have been solved for months ago, when the first developer releases were issued.
No response from Ciso however.
This is really bad.
Other companies already have solutions for their products in order to be compatible with Lion.
Ok, I agree, this might not be a problem caused by Cisco, but a problem that was caused by Apple when releasing Lion. But hey all companies have to update their software so Cisco as well as Apple.
However, companies of major size (Apple, Cisco, and many others) should be more cooperative when releasing new software.
I work in IT for over 30 years now and I have always seen that when Cisco bought a company, their "boxes" were painted gray and the Cisco "bridge" logo was aplied and then all over sudden it became a REAL Cisco product.
And I mean it really became a Cisco product. You might have some minor problems but those were always solved.
I would have expected the same from Cisco with respect to these NAS'ses.
And believe me, I have seen quit some NAS'ses from the competitors but the NSS32x series does not come with the support you get from other competing NAS vendors.
That is what bothers me and I regret that there is no solution today for the issue(s) we have with OS X Lion, but what bothers me even more is that Cisco is not informing us at all about whatever solution there will be within whatever time frame.
I still have the NSS326 and I had to pay quit a premium over other vendors, but accepted it, supposing that the NAS would have the support I am familiar with from Cisco, but as you can read above I am disapointed.
So Cisco, what are you going to do to improve support and be more open and informative about coming software releases for the NSS32x series NAS'ses?
Regards,
Klaas de Jong

Unable to enter administration page of NSS 326

Even after a soft reset, we are unable to enter the administration page of our NSS 326, and even through the NSS Discovery tool, we can't configure as it asks the admin username and password ( the default is expected to be admin-admin after the soft reset but doesn't work). Any help would be useful. Thank you in advance.

That may be because the clock settings on your computer are not the same as the clock in general, or perhaps because the clock on your computer is dead..
to deal with you can reset your clock on your computer or sertivikat looking at options on the right side and then choose to agree if it has been found..

NSS 326 disk replace failed

Hi
I have replaced the faulty disk in RAID6 with a new one on NSS 326, but NSS does not accept it with the error:
[RAID6 Disk Volume: Drive 1 2 3 4 5 6] Add drive 1 to the volume failed.
Under the "RAID Managment" it says I should insert a disk the same or bigger size that faulty one was.
All hard disk are the same vendor,model,type and size (also the replacement disk is the same):
WDC WD2003FYYS-02W0B01.0
Does anyone have any clue what should I do?
Thank you in advance
Herbert Knavs

Hi Herbert,
   I am glad your unit now is fully operational and the unit had the healthy RAID6 array. To answer your questions and share some of the informatioin I knew, I am doing my best with my knowlege of the NSS:
When rebuild started, another strange thing happened... I will copy paste from log here:
1. Drive 1 plugged in.
2. [RAID6 Disk Volume: Drive 1 2 3 4 5 6] Drive 1 added into the volume.
3. [RAID6 Disk Volume: Drive 1 2 3 4 5 6] Start rebuilding.
4. [RAID6 Disk Volume: Drive 1 2 3 4 5 6] Rebuilding skipped.
    Why skipped???   [ Clint's comment: During the rebuild process, disk #3 could not be in sync with other disks and after many attempted to sync data in the array, the process/script timed out and killed the rebuild array process because disk#3 may contains some bad blocks. System log displayed "Rebuilding skipped". The log, as you can see it always displayed 6 disks [1 2 3 4 5 6]. This is just for user to understand that RAID6 with 6 disks but it does not reflect the true status of the array.]
5. [RAID6 Disk Volume: Drive 1 2 3 4 5 6] Start rebuilding.
    But in the "Raid Management" view was: 1 2 4 5 6 (disk number 3 somehow is missing)
[Clint's comment: The GUI displayed the true status of the RAID array, as you know disk#3 is failed out from the RAID6 array.]
6. [RAID6 Disk Volume: Drive 1 2 3 4 5 6] Rebuilding completed.
    Now "Raid Managment" view says something like: 1 2 4 5 6 In degraded mode... and number 3 is also missing here???
[Clint's comment: System continue the process of resync without disk #3 and after it completed. It would gave user in degraded mode because disk#3 is not in the array.]
So I have rebooted the NSS without touching disk in bay .
7. System started.
8. [RAID6 Disk Volume: Drive 1 2 3 4 5 6] Drive 3 added into the volume
9. [RAID6 Disk Volume: Drive 1 2 3 4 5 6] Start rebuilding.
[Clint's comment: by reboot the system. There is a process of checking each disk during boot up to verify each disk is physically healthy (no bad blocks, if it is, fix it before boot to Linux OS and execute codes to bring NSS to operational). The system did know the status of each disk and in your case, because disk #3 was not in the array. System checked and verified to correct some bad blocks that was out of sync in the array. After fixed some bad blocks, it automatically add that disk to the array and required resynchronize to make sure all disks are in the RAID6 array, this is why you were seeing "Start rebuilding" after the reboot. And because the correction was made in disk #3, you had the successful rebuild RAID6 array.]
Hope that helps!
Regards,
-Clint

9630 Keyboard/Buttons not working; hard resets and multiple reloads of OS did not correct

My BlackBerry 9630 Tour is a little more than a year old. Yesterday the keyboard, trackball, and all buttons stopped working while I was typing out an email. I could not power off the Blackberry without removing the battery for a hard reset. Unfortunately, even after many hard resets, the problem persisted, so I went to the forums for help and tried everything that seemed relevant (multiple times) with no success.
After reviewing a number of tech support posts, this problem does not appear to be unique to any given model of BB and contact with liquids is cited as a common but not the only cause for this condition.
I was outside on a very hot and humid day when the malfunction occurred so it is possible some perspiration may have come into contact with the keypad, convenience buttons, or trackball and caused the lockup.
I'm looking for someone with more smarts than me to help me troubleshoot, identify the actual problem, and identify the proper corrective actions. See below for a synopsis of my actions taken, with the exception of taking it to the shop for repair/replacement.
The corrective actions listed on the forums and blogs are varied but essentially fall into two primary solutions:
1. If moisture is suspected to be the issue, let the BB dry out overnight
    a. Pull the battery, naturally air dry or use a blow dryer, let it sit unplugged with no battery for at least 12 hours
    b. If this doesn't immediately work, try a clean install of the OS (see below)
    c. If this doesn't work, take to the shop and they'll either replace the keyboard and/or trackball or replace entire unit
2. If moisture is not suspected to be a factor then perform a backup followed by a clean install of OS
     a. Backup your files using Desktop Manager Backup and Restore
     b. Do a clean reinstall OS using Desktop Manager Application Loader
         i. The OS installation process is dicey and takes a little patience and focus-- you have to wait for the Desktop Manager to properly recognize the device before it can proceed on some of the steps and it may take several iterations to get completely through the process and get the "successful installation" message.
         ii. Further, you may need to keep the battery removed during the initial steps in the process and only insert it when the process gets to the point of actually trying to copy files into the BB memory
            * The BB LCD will display an icon that looks like a battery with a slash through it letting you know the process cannot proceed until a battery is inserted and the Desktop Manager Application Loader will also give you an error indicating it cannot find the device.
            * After inserting the battery, it will take a few seconds or more for the computer to recognize the USB device and for Desktop Manager to respond with the BB password pop-up window.
            * After typing in your BB password, the installation should continue.
    c. If you can get the OS successfully reloaded and your keyboard/trackball/buttons work -- great -- now restore your files and settings using Desktop Manager Backup and Restore and get on with your life.
    d. If this does NOT work after multiple successful clean OS installations apparently you are completely hosed; the only other option is to get it to the shop for repair or replacement.
1.. Does anyone have a troubleshooting procedures that will identify whether moisture is the root cause or not?
2. Is there another corrective procedure that's been missed?

Took BB to Sprint Store and technician took it apart, saw no evidence of moisture or any other damage, and concluded that the keyboard had failed. Not an uncommon occurance.
Also, he told me you cannot simply replace the keyboard, it is integral to the systemboard, so you need to replace the entire device.
He did commend the troubleshooting approach used prior to going to the store -- most folks won't take the time to do even basic troubleshooting (like taking out the battery), they just go to the store and say "fix it please". He confirmed that the steps outlined in the initial post were correct and did not have any other solutions.
Take away:
If you want to do some troubleshooting yourself to check for moisture, the process was pretty straightforward. After watching the technician, most folks with a little technical or mechanical aptitude should be able to manage the dismantling process. You just need a small phillips head screwdriver and a little patience. Good lighting and a magnifying glass or reading glasses also help!

T2 Digitizer frozen after soft,warm,hard resets.Can not get it to calibrate at all.

My T2 occasionally has to be recalibrated. I downloaed DigiFix some months ago and it seemed to help a bit. I hot synced my data last night and all was well. This morning I could not tap my screen to access anything. I tried cleaning carefully around the screen edge, gently cleaned the screen ( no visible damage to the screen noted ), performed a soft reset ( which usually worked ), a warm reset, followed by a soft reset and finally a hard reset ( kept data ) followed by a soft reset and then the big one, a hard reset with loss of data followed with 5 soft resets in a row. I found through the forum a T2 update which I downloaded and is ready to be installed when I next hot sync.
The unit is now frozen with the x in the starting position in the top left corner. Despite my efforts to gently tap all around the X, I can not get it to recalibrate or even get off the calibration screen. If I could just get back to any regular screen, I could get my data back and install this T2 update.
I also downloaded Pocket DVD studio a week ago and have been able to upload .avi files for viewing videos on my Palm. I works beautifully. I think I still have the original Kimoma player on my T2, but never really like it. Can anyone PLEASE help me out? This T2 update is supposed to help according to the infor I found in forum....MANY THANKS!
Post relates to: Tungsten T2
This question was solved.
View Solution.

Thank you for the fina advice. It worked and my T2 is now working perfectly. I think the real trick is using cheap copier paper, not the higher grade stuff or a business card for the cleaning routine. I floded the paper lengthwiase and put a sharp crease in before cutting into little work strips. It took a lot of patience and time to perform a proper cleaning, but it was worth it. Seems that the smallest bit of anything which get trapped under the bezel will throw the T2 into a stupor. Many thanks your your fine advice.....Rgds,John Brown
Post relates to: Tungsten T2

IPhone 5s doesn't ring and goes directly to voice mail. Do not disturb is disabled. Have reset network settings and did a hard reset. What am I missing?

iPhone 5s doesn't ring and goes directly to voice mail. Do not disturb is disabled. Have reset network settings and did a hard reset. What am I missing?

Call your phone carrier - that's a problem for them to resolve.

Trackpad on 2011 i7 MBA has stopped working twice and won't work again until I do a hard reset. Battery is not hot. MBA is 2 weeks old. What's up, Apple?

Twice, shortly after turning on my MBA from a restful night's sleep, my keyboard and trackpad have stopped working. Works fine after a hard reset, but considering this baby is brand new, it shouldn't be happening.
I am in law school and don't have time to leave my MBA with applecare.
HELP!

hello, i have the same problem with my mbp. and you should first shut off your MB. then when is complete off plug in your charger and hold shift+option+command+power and within 10 second you will see the front led flash 10 times more or less and your MB will restart and it should work normal

My iPhone 4 died. I tried charging it for 3 hours; it wont hard reset or even show up on my computer or itunes. is there anything i can do?

My iPhone 4 died. I tried charging it for 3 hours; it wont hard reset or even show up on my computer or itunes. is there anything i can do?

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar
You can also try going to Settings>General>Reset>Ease all content and Settings. However, you may not be able to restore via iTunes. You might only be able to only restore from iCloud backup if you have a hardware problem,

Mid 2010 MacBook Pro Keeps Hard Resetting

Hi,
I have had my MacBook pro 4 years now since new and for the past week it has started to experience issues. I am running OS X 10.8.4 and it is all up to date. This did not start as a result of adding new software or plugging in any new hardware it just seemed to start by itself.
Sometimes when I turn off my MacBook (either by clicking shutdown or pressing the power button and clicking on the shutdown) it then seems to freeze for a second and then do a hard shutdown - it usually turns itself back on again and then I get the error message on startup saying that my computer restarted because of a problem.
Sometimes when I turn my MacBook on it will not turn on - I can hear the chime but the screen stays black (the keyboard lights do come on) - I have to hold down the power button and try again.
Sometimes when I wake my MacBook from sleep it will do a hard reset similar to above.
I have also had it hard resetting when I open a specific application (Brackets, and today I have tried updating my Java and 3 times in a row mid way through the download it hard reset).
So far I have tried resetting the PRAM and the SMC, I have also verified my hard drive (states it is OK) and the disk permissions (when I verify the disk permissions I get lots of errors about itunes content which when I repair the disk permissions it does not seem to repair as next time I try it is the same again).
There does not seem to be any common theme to any of these as some days it will be fine and others it might take 5 atempts to turn it on and then off again.
When it hard resets and starts up again it get an error log such as this one:
panic(cpu 0 caller 0xffffff7f8de96f1a): "GPU Panic: [<None>] 3 3 7f 0 0 0 0 3 : NVRM[0/1:0:0]: Read Error 0x00004160: CFG 0xffffffff 0xffffffff 0xffffffff, BAR0 0xd2000000 0xffffff8098a20000 0x0a5480a2, D0, P0/4\n"@/SourceCache/AppleGraphicsControl/AppleGraphicsControl-3.4.5/src/AppleM uxControl/kext/GPUPanic.cpp:127
Backtrace (CPU 0), Frame : Return Address
0xffffff80ac793460 : 0xffffff800b81d636
0xffffff80ac7934d0 : 0xffffff7f8de96f1a
0xffffff80ac7935a0 : 0xffffff7f8bf7088c
0xffffff80ac793660 : 0xffffff7f8c04385a
0xffffff80ac7936a0 : 0xffffff7f8c20a2f2
0xffffff80ac7936c0 : 0xffffff7f8c20a408
0xffffff80ac7936f0 : 0xffffff7f8c20ae9e
0xffffff80ac793720 : 0xffffff7f8c20ad73
0xffffff80ac793750 : 0xffffff7f8c303e5c
0xffffff80ac793950 : 0xffffff7f8c303a7d
0xffffff80ac7939f0 : 0xffffff7f8c06e747
0xffffff80ac793a20 : 0xffffff7f8c3037b2
0xffffff80ac793b10 : 0xffffff7f8c06e732
0xffffff80ac793b40 : 0xffffff7f8c301d55
0xffffff80ac793b90 : 0xffffff7f8c32bf20
0xffffff80ac793be0 : 0xffffff7f8c0b5b77
0xffffff80ac793c40 : 0xffffff7f8c0b61ab
0xffffff80ac793cb0 : 0xffffff7f8c32b7c0
0xffffff80ac793cf0 : 0xffffff7f8c30946c
0xffffff80ac793e20 : 0xffffff7f8c06c345
0xffffff80ac793e40 : 0xffffff7f8bf7765f
0xffffff80ac793ef0 : 0xffffff800bc50e58
0xffffff80ac793f30 : 0xffffff800bc4f95a
0xffffff80ac793f80 : 0xffffff800bc4fa89
0xffffff80ac793fb0 : 0xffffff800b8b3257
      Kernel Extensions in backtrace:
         com.apple.driver.AppleMuxControl(3.4.5)[49FEF732-D7A3-327B-A7AA-6AC5A6E3DCFF]@0 xffffff7f8de89000->0xffffff7f8de9bfff
            dependency: com.apple.driver.AppleBacklightExpert(1.0.4)[B5B1F368-132E-3509-9ED5-93270E3ABB DD]@0xffffff7f8de84000
            dependency: com.apple.iokit.IOPCIFamily(2.8)[2FAEA49C-EA4C-39C6-9203-FC022277A43C]@0xffffff 7f8be75000
            dependency: com.apple.driver.AppleGraphicsControl(3.4.5)[4A2C8548-7EF1-38A9-8817-E8CB34B8DC A6]@0xffffff7f8de70000
            dependency: com.apple.iokit.IOACPIFamily(1.4)[A35915E8-C1B0-3C0F-81DF-5515BC9002FC]@0xfffff f7f8bdf3000
            dependency: com.apple.iokit.IONDRVSupport(2.3.7)[F16E015E-1ABE-3C40-AC71-BC54F4BE442E]@0xff ffff7f8befb000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.7)[9928306E-3508-3DBC-80A4-D8F1D87650D7]@0 xffffff7f8beb8000
         com.apple.NVDAResman(8.1.6)[39D35403-42FB-3F08-999C-9866938D6B3A]@0xffffff7f8bf 0f000->0xffffff7f8c1b2fff
            dependency: com.apple.iokit.IOPCIFamily(2.8)[2FAEA49C-EA4C-39C6-9203-FC022277A43C]@0xffffff 7f8be75000
            dependency: com.apple.iokit.IONDRVSupport(2.3.7)[F16E015E-1ABE-3C40-AC71-BC54F4BE442E]@0xff ffff7f8befb000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.7)[9928306E-3508-3DBC-80A4-D8F1D87650D7]@0 xffffff7f8beb8000
         com.apple.nvidia.nv50hal(8.1.6)[BF3CC142-4112-3E23-BCE2-CDCFD5811DDA]@0xffffff7 f8c1be000->0xffffff7f8c491fff
            dependency: com.apple.NVDAResman(8.1.6)[39D35403-42FB-3F08-999C-9866938D6B3A]@0xffffff7f8bf 0f000
            dependency: com.apple.iokit.IOPCIFamily(2.8)[2FAEA49C-EA4C-39C6-9203-FC022277A43C]@0xffffff 7f8be75000
BSD process name corresponding to current thread: kernel_task
Mac OS version:
12F45
Kernel version:
Darwin Kernel Version 12.5.0: Sun Sep 29 13:33:47 PDT 2013; root:xnu-2050.48.12~1/RELEASE_X86_64
Kernel UUID: EA38B02E-2B88-309F-BA68-1DE29F605DD8
Kernel slide:     0x000000000b600000
Kernel text base: 0xffffff800b800000
System model name: MacBookPro6,2 (Mac-F22586C8)
System uptime in nanoseconds: 8604629774
last loaded kext at 7530596048: com.apple.driver.AppleHWSensor    1.9.5d0 (addr 0xffffff7f8dc1b000, size 36864)
loaded kexts:
com.squirrels.airparrot.framebuffer    3
com.squirrels.driver.AirParrotSpeakers    1.7
com.apple.driver.AppleHWSensor    1.9.5d0
com.apple.filesystems.autofs    3.0
com.apple.driver.AGPM    100.13.14
com.apple.driver.AppleTyMCEDriver    1.0.2d2
com.apple.iokit.IOBluetoothSerialManager    4.1.7f2
com.apple.driver.AppleMikeyHIDDriver    124
com.apple.driver.AppleHDAHardwareConfigDriver    2.4.7fc4
com.apple.driver.AppleHDA    2.4.7fc4
com.apple.iokit.IOBluetoothUSBDFU    4.1.7f2
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport    4.1.7f4
com.apple.driver.AppleMikeyDriver    2.4.7fc4
com.apple.driver.AudioAUUC    1.60
com.apple.iokit.IOUserEthernet    1.0.0d1
com.apple.Dont_Steal_Mac_OS_X    7.0.0
com.apple.driver.ApplePolicyControl    3.4.5
com.apple.driver.AppleLPC    1.6.3
com.apple.driver.AppleBacklight    170.3.5
com.apple.GeForce    8.1.6
com.apple.nvidia.NVDAStartup    8.1.6
com.apple.driver.AppleSMCPDRC    1.0.0
com.apple.driver.AppleUpstreamUserClient    3.5.12
com.apple.driver.AppleMCCSControl    1.1.11
com.apple.driver.AppleIntelHDGraphics    8.1.6
com.apple.driver.AppleIntelHDGraphicsFB    8.1.6
com.apple.driver.AppleMuxControl    3.4.5
com.apple.driver.AppleSMBusPCI    1.0.11d1
com.apple.driver.AppleSMCLMU    2.0.3d0
com.apple.driver.ACPI_SMC_PlatformPlugin    1.0.0
com.apple.driver.SMCMotionSensor    3.0.3d1
com.apple.driver.AppleUSBTCButtons    237.1
com.apple.driver.AppleUSBTCKeyEventDriver    237.1
com.apple.driver.AppleUSBTCKeyboard    237.1
com.apple.driver.AppleUSBCardReader    3.3.1
com.apple.driver.AppleIRController    320.15
com.apple.driver.AppleFileSystemDriver    3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless    1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib    1.0.0d1
com.apple.BootCache    34
com.apple.iokit.SCSITaskUserClient    3.5.6
com.apple.driver.XsanFilter    404
com.apple.driver.AppleUSBHub    635.4.0
com.apple.driver.AirPort.Brcm4331    615.20.17
com.apple.iokit.IOAHCIBlockStorage    2.3.5
com.apple.iokit.AppleBCM5701Ethernet    3.6.2b4
com.apple.driver.AppleFWOHCI    4.9.9
com.apple.driver.AppleAHCIPort    2.6.6
com.apple.driver.AppleUSBEHCI    621.4.6
com.apple.driver.AppleUSBUHCI    621.4.0
com.apple.driver.AppleSmartBatteryManager    161.0.0
com.apple.driver.AppleACPIButtons    1.8
com.apple.driver.AppleRTC    1.5
com.apple.driver.AppleHPET    1.8
com.apple.driver.AppleSMBIOS    1.9
com.apple.driver.AppleACPIEC    1.8
com.apple.driver.AppleAPIC    1.7
com.apple.driver.AppleIntelCPUPowerManagementClient    214.0.0
com.apple.nke.applicationfirewall    4.0.39
com.apple.security.quarantine    2.1
com.apple.driver.AppleIntelCPUPowerManagement    214.0.0
com.apple.kext.triggers    1.0
com.apple.iokit.IOSerialFamily    10.0.6
com.apple.driver.DspFuncLib    2.4.7fc4
com.apple.iokit.IOBluetoothHostControllerUSBTransport    4.1.7f2
com.apple.iokit.IOSurface    86.0.4
com.apple.iokit.IOBluetoothFamily    4.1.7f2
com.apple.iokit.IOAudioFamily    1.9.2fc7
com.apple.kext.OSvKernDSPLib    1.12
com.apple.nvidia.nv50hal    8.1.6
com.apple.NVDAResman    8.1.6
com.apple.iokit.IOFireWireIP    2.2.5
com.apple.driver.AppleSMBusController    1.0.11d1
com.apple.driver.AppleHDAController    2.4.7fc4
com.apple.iokit.IOHDAFamily    2.4.7fc4
com.apple.driver.AppleGraphicsControl    3.4.5
com.apple.driver.AppleBacklightExpert    1.0.4
com.apple.iokit.IONDRVSupport    2.3.7
com.apple.iokit.IOGraphicsFamily    2.3.7
com.apple.driver.IOPlatformPluginLegacy    1.0.0
com.apple.driver.IOPlatformPluginFamily    5.4.1d13
com.apple.driver.AppleSMC    3.1.5d4
com.apple.driver.AppleUSBMultitouch    237.3
com.apple.iokit.IOSCSIBlockCommandsDevice    3.5.6
com.apple.iokit.IOUSBMassStorageClass    3.5.2
com.apple.iokit.IOUSBHIDDriver    623.4.0
com.apple.driver.AppleUSBMergeNub    621.4.6
com.apple.driver.AppleUSBComposite    621.4.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice    3.5.6
com.apple.iokit.IOBDStorageFamily    1.7
com.apple.iokit.IODVDStorageFamily    1.7.1
com.apple.iokit.IOCDStorageFamily    1.7.1
com.apple.iokit.IOAHCISerialATAPI    2.5.5
com.apple.iokit.IOSCSIArchitectureModelFamily    3.5.6
com.apple.iokit.IO80211Family    530.5
com.apple.iokit.IOUSBUserClient    630.4.4
com.apple.iokit.IOEthernetAVBController    1.0.2b1
com.apple.iokit.IONetworkingFamily    3.0
com.apple.iokit.IOFireWireFamily    4.5.5
com.apple.iokit.IOAHCIFamily    2.5.1
com.apple.iokit.IOUSBFamily    635.4.0
com.apple.driver.AppleEFINVRAM    2.0
com.apple.driver.AppleEFIRuntime    2.0
com.apple.iokit.IOHIDFamily    1.8.1
com.apple.iokit.IOSMBusFamily    1.1
com.apple.security.sandbox    220.3
com.apple.kext.AppleMatch    1.0.0d1
com.apple.security.TMSafetyNet    7
com.apple.driver.DiskImages    345
com.apple.iokit.IOStorageFamily    1.8
com.apple.driver.AppleKeyStore    28.21
com.apple.driver.AppleACPIPlatform    1.8
com.apple.iokit.IOPCIFamily    2.8
com.apple.iokit.IOACPIFamily    1.4
com.apple.kec.corecrypto    1.0
If anybody has any ideas why it is doing this or suggestion on what I can do to either fix it or diagnose it it would be grateful to hear them

You have the misfortune of having a 15" 2010 6.2 model identifier MBP. It is having GPU problems.
http://support.apple.com/kb/ts4088
Make an appointment at an Apple store genius bar for a FREE evaluation. You will be advised of your options.
Ciao.

Exchange PUSH no longer working. Did a hard reset, and restore nothing

Seems this problem is happening everywhere on HOFO and macrumors. Please someone help. I bought this phone for this reason and I am ready to take it back. I need to get my emails as soon as they come in. Apple support was useless too. They know about the problem, but no fix is available. GRR!
The phone was working fine at first, receiving emails, etc. Then it stopped. It would only pull the emails from exchange when you click on the MAIL button and it goes to the next screen. All the settings are set to Push for exchange. Contacts still sync right away. Email will not. We have over 80 other PDA Windows Mobile phones with no problems. I have tried WIFI, 3G only, neither work. Hard reset, restore, new phone settings, etc. Nothing!
Message was edited by: nizmoz

probably not quite the same issue as yours, but thought I'd mention it. After switching connection types, my iPhone no longer will push or sync mail. I get a server connection error. I've found that vpn'ing in, sync'ing, then turning VPN off will restore push and sync abilities. I'm hoping this gets fixed, by it's my workaround for now.

My iPhone 3gs will not turn on, charge, or allow me to perform a hard reset. iTunes nor my computer recognizes it andthe screen wont light up at all. What can I do to fix this?

I have an iPhone 3gs that is out of warranty. I purchased this phone from AT&T. Last night my phoone went completely dead (battery percentage was at 96% just moments before) and now will not turn back on. I have tried just about everything I have found on discussion boards- trying hard reset, plugging into itunes, charging for15-20 mins then holding down sleep and homebuton..... NOTHING works. This phone will not light up AT ALL. My computer wont even recognize it. Is there anything else I can do?

Make an appointment at an Apple store if there is one nearby.

My apps wont open and i keep downloading new apps, hard resetting, syncing and nothing works! PLEASE HELP

My apps wont open and i keep downloading new apps, hard resetting, syncing and nothing works! PLEASE HELP

Then restore the iPod. First from backup and if problem persists, restore to factory defaults/new iPod.

Problems with partitions after hard reset

Hi hope some can help here, I installed Maverick on my imac and everything seemed fine, I went to work and came home to find a black screen with nothing but the mouse cursor, however the computer wouldnt respond in any way so had to do a hard reset when the computer restarted I would get the Aplle logo and the spinning wheel then the computer would restart it kept doing this over and over.
I restared the computer went into DU tried to repair disk and kept getting errors, my drive is 3TB i have a 1TB primary Partition and a second of 2TB I tried to erase and reformat the primary partition but got an error half way through now both partitons are greyed out with no way or deleting or doing anything with them I have also noticed I no longer have the hard drive make and model in the list just Mackintoh HD and my second partition, to make matters worse my second partition is now unmounted and and when I try to mount it says it needs to be repaired but wont repair, I really need totry and get the data from the second partiton but im struggling, when I tried to reinstall os x it cant see a drive to install to nothing shows up, I even booted using diskwarrior and even it couldnt see the drive, I know this drive is ok this is a software issue the partition table seems to be corrupt or something help!!
Its worth mentioning I had Parallels and Windows 7 on the primary partiton could the windows partiton have caused an issue when I tried to erase and reformat the partition?
Message was edited by: seanybdj

The drive has failed.

Hard reset on NAS NSS 326

Similar Messages

Maybe you are looking for