Harddisk not found by Windows-XP-Setup + RnR does not work at all !?!

Hi all,
I wanted to recover a my system (R61, 8943-DKG) using RnR from the Windows XP-platform. It took more than 24 hours and "finished" with a reboot saying "windows could not be startet, as the following file is missing or has been damaged: \windows\system32\c_1252.nls. You may try to repair the file by starting the Windows setup from the original CD. Use the "R"-Option to start the setup-repairing" (this is my translation of the german message I got, the exact english wording thus might be different).
Two problems occur and leave me with no options/ideas at the moment:
1) Starting the "R"-Option or the "install new"-option of a windows setup from an XP-CD (from another machine, the ThinkPad came without any CDs/DVDs), gives me the message "no harddisk could be found". In the BIOS the harddisk is found an the hardware check passed.
2) Pushing the blue Thinkvantagebutton while booting starts the Rescue and Recovery software, but after "configuring your system" the laptops reboots, so no chance to start RnR !?!
My questions to the honoured community:
a) Is there any chance to make the harddisk "visible" for the XP-Setupprogram?
b) Do you have another idea how to start the RnR-software in order to at least reinstall windows-XP freshly from the harddisk?
Thanks in advance for any help!
JoerchS.

Hi JoerchS,
1. You need to go into BIOS and set 'SATA AHCI' mode to 'Compatibility' under hard disk drive option for your HDD to be seen by Win XP CD.
2. Sounds like the partition has become corrupt. To recover you system again, recovery discs are needed. If you have not created recovery discs in advance [http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-70804] then you will have to obtain them from lenovo usually for a fee.
Hope it helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

Similar Messages

When I try and play music on my iPhone downloaded from iTunes it says 'this URL is not found on this server'. This does not happen when I play the same music through my iPad. Can anyone help?

When I try to play music downloaded from itunes on my iPhone 4S it says 'this URL is not found on the server'. This does not happen when I play the same music on my iPad. The music plays fine. The message also comes up when I try and login to iTunes on my iMac. Can anyone help?

I too am having the same issue as the OP.
Your USER AGENT information is Mozilla/5.0 (Macintosh; Intel Mac OS X 10_10_2) AppleWebKit/600.3.18 (KHTML, like Gecko) Version/8.0.3 Safari/600.3.18
Every webserver that receives a request from your browser is able to determine the HTTP USER AGENT information unless it has been removed by some software (e.g. firewall) before the request was trasmitted.

Dv9000 laptop dvd drive and webcam not found. drive initializes on boot but does not show up.

The DVD/CD-Rom drive will initialize and will read a CD when inserted but it does not show up in the BIOS or in Windows. It's a Lighscribe drive. The webcam was not found either. I recently reloaded this machine for a friend back to the factory setup. Installed all additional software and everything is working but the drive and the camera. Is there any way to actually test these devices for failure? Or is there a patch or a software package I may be missing? It's a dv9000 but it has dv9007 on the bottom. And an AMD processor. If anybody has any ideas I would greatly appreciate the help.

Spoiler (Highlight to read)
It does not show up in either one. The camera or the DVD drive. No X's or error Triangles. I guess they could have gone bad at the same time but that's not likely. It would be one heck of a coiencidence. I am wondering if there is an alternate chipset driver or patch. Maybe a controller driver? The system has dv9000 on the display and dv9700 on the model # tag. I believe 1 is Inter and the other NVidia. But the Factory image installed the NVidia drivers.

Downloaded new version itunes to Windows 7, now receiving error while computer is booting Apple Sync Notifier.exe- Entry Point Not Found the procedure entry point sqlite3_wal_checkpoint could not be located in the dynamic link library SQLite.dll., Help!

Downloaded new version itunes to Windows 7, now receiving error while computer is booting Apple Sync Notifier.exe- Entry Point Not Found the procedure entry point sqlite3_wal_checkpoint could not be located in the dynamic link library SQLite.dll., Help! How do I remove this message every time I start up Windows? Would it help to
re-install Itunes and what version??

Refer to this thread - https://discussions.apple.com/message/15685210#15685210
Quick answer "copy the file SQLite3.dll from the C:\Program Files (x86)\Common Files\Apple\Apple Application Support folder to the C:\Program Files (x86)\Common Files\Apple\Mobile Device Support folder"

Windows 8.1 Setup DVD does not see SSD

Windows 8.1 Enterprise x64 Setup DVD does not see Samsung SSD 840 Pro so cannot install Windows 8.1. The same SSD disk currently does have Windows 8 Enterprise and runs fine on the same laptop. Checked the Dell BIOS does see the SSD. Loaded the
latest drivers from the Dell website but did not help. Tried changing the BIOS settings from SSD to ACHI. When in setup did the SHIFT+F10 to run the DISKPART clean the partitions.
How do I troubleshoot why the Windows 8.1 Enterprise setup disc cannot see the SSD?

Hi,
According to your description, I would like to confirm if you can see SSD under the Diskpart.
If you can see the SSD under the Diskpart,I think it is related to the installation DVD.
I suggest we use a new installation DVD to test it.
Also, you can create a bootable USB flash drive, and then use the USB flash drive to install Windows.
Keep post.
Regards,
Kelvin hsu
TechNet Community Support

HT1751 unable to open itunes because MSVCR80.dl was not found error7 windows error126

cannot open itunes because MSVCR80.dl was not found error7 windows error126

Check out this page: Troubleshooting issues with iTunes for Windows updates

IRecruitment Vacancy Approval is not found in Approval Process Setup

hi
my ebs is 12.1.1
After Setting up AME for iRecruitment, i get problems as follows:
1: Approvals Management Business Analyst -->Business Analyst Dashboard
i find 'iRecruitment Vacancy Approval' is not found in Approval Process Setup.
2:when i click Approvals Management Administrator respsonbility. it get errors:
java.lang.NullPointerException
     at oracle.apps.fnd.framework.webui.OAAdvancedTableHelper.setMetaDataProperties(OAAdvancedTableHelper.java:391)
     at oracle.apps.fnd.framework.webui.OAAdvancedTableHelper.createWebBean(OAAdvancedTableHelper.java:183)
please help me.
thanks.

2:when i click Approvals Management Administrator respsonbility. it get errors:
java.lang.NullPointerException
     at oracle.apps.fnd.framework.webui.OAAdvancedTableHelper.setMetaDataProperties(OAAdvancedTableHelper.java:391)
     at oracle.apps.fnd.framework.webui.OAAdvancedTableHelper.createWebBean(OAAdvancedTableHelper.java:183)Can you find any details about the error in Apache log files (error_log* and access_log*)?
Please see if (Java.Lang.Indexoutofboundsexception: Index:0 Size:0 When Adding Another Skill [ID 1361546.1]) helps.
Also, make sure you have the "Approvals Management %" role added to the account you use -- After AME.B Responsibilities Give > There Are No Functions Available For This Responsibility [ID 340969.1]
Thanks,
Hussein

Dotfuscator CE error: External type not found System.Windows.Input.ICommand,PresentationCore

Preemptive will not support CE so I am trying here...
I have an application targeting the .NET Framework 4.0. It builds and runs fine but I cannot get it to compile in Dotfuscator CE. I am stuck.
Dotfuscator CE (v5.0.2500.0) with Visual Studio 2010 SP1. Here is the Error:
Resolving method references...
External type not found System.Windows.Input.ICommand,PresentationCore, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35.
Build Error.
The problem seems to originate from ICommand being moved from PresentationCore.dll (in NET 4.0) to System.dll (in NET 4.5). Studio handles this and compiles fine as I am targeting NET 4.0 and the references all point to
C:\Program Files (x86)\Reference Assemblies\Microsoft\Framework\.NETFramework\v4.0\
Dotfuscator CE however does not seem to handle it correctly and I am not sure how to correct the issue. Any help would be greatly appreciated!!

Hi Perter,
Thanks for your response.
External type not found System.Windows.Input.ICommand,PresentationCore, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35.
Maybe it is related to the references in your project.
Reference:
The type 'System.Windows.Input.ICommand' exists in both 'PresentationCore.dll' and 'System.dll'
Since it is not the VS General issue, I am moving your question to the moderator forum ("Where is the forum for..?").
The owner of the forum will direct you to a right forum. Thanks for your understanding.
Best Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Windows 8.1, BootCamp does not find the ISO image.

When I try to install Windows 8.1, BootCamp does not find the ISO image.
I purchased Windows 8.1 Pro, I downloaded the .exe requested file from a Windows computer, performed the steps recommended by Microsoft in order to create the ISO file saving it on a flash drive as well and, as a precaution, on a DVD too.
I performed the "Download the latest Windows Support Software from Apple" step directly into another flash drive and having it completed BootCamp displays the following message:
"The installer disc could not be found – Insert the Windows installer disc and wait a few seconds for the disc to be recognized. "
So happens that I have tried this using the DVD, pendrive and also copying the ISO file to the desktop and to the "Documents" folder as recommended in certain websites, but none of this has made the process go ahead. What can I do?
My equipment is a mid 2011 iMac running Mac OSX 10.10.1.

Dear Loner T,
thanks to my coworker, the solution was unpacking from that ISO file which I had recorded (according to the steps indicated by Microsoft), but now using Nero software (Windows) and then recording by the most common way in a new DVD. See the screen of the first DVD before unpacking:
This true saga only demonstrated that the generated ISO file as an option at the time of the Windows installation, is not for direct installation through BootCamp, and as a I could check, even for direct installation on a Windows PC. See the last DVD burned using Nero and again recorded:
The execution of BootCamp, was perfect
Thank you for attention to my problem!

Why is it that every udate of my iPhone software do I get the error message on my laptop: AppleSyncNotifier.exe - Entry Point Not Found The procedure enrty point xmlTextReaderConstName could not be located in the dynamic link library libxml2.dll

Each time I update the software on my iPhone4 I get the following error message on my lap top: AppleSyncNotifier.exe - Entry Point Not Found The procedure enrty point xmlTextReaderConstName could not be located in the dynamic link library libxml2.dll
I go on line to find a solution, but it must be a common problem, why has apple not corrected yet?

This is the fix I got from discussions and it worked for me. It is copied below. I just did the manual fix which I have underlined. Good luck! Regards, Belle.
This can occur because libmxl2.dll is not in your C:\Program Files\Common Files\Apple\Mobile Device Support folder.
There have been some issues with this and other dlls not being in the right place (or not being everywhere they should be) since the 10.3.1.55 iTunes update.
However, I note that the 10.4 iTunes update is now out - surprisingly quickly - so try installing that, rebooting, and see if your issue is solved.
If it isn't, though, here's the manual fix:-
With Windows Explorer, navigate to your C:\Program Files\Common Files\Apple\Apple Application Support folder.
Copy the libmxl2.dll that you should find there, navigate to the nearby Mobile Device Support folder, and Paste it in there also.
Reboot and see if all is well.
I actually had the issue with SQLite3.dll, and the above fix worked for me (I found it in an April 2010 posting!).
I passed on the fix as above for the similar issue with libmxl2.dll to someone who had exactly your problem, and he reported that it fixed it for him.

Since updating to 10.4 getting error message on startup 'AppleSyncNotifier.exe – Entry Point Not Found, The procedure entry point xmlTextReaderConstName could not be located in the dynamic link library libxml2.dll.'. How do I fix this annoying problem?

Since updating to 10.4 I've been getting this error message on computer startup
'AppleSyncNotifier.exe – Entry Point Not Found
The procedure entry point xmlTextReaderConstName could not be located in the dynamic link library libxml2.dll.'.
Please help me fix this annoying problem?
belle

This is the fix I got from discussions and it worked for me. It is copied below. I just did the manual fix which I have underlined. Good luck! Regards, Belle.
This can occur because libmxl2.dll is not in your C:\Program Files\Common Files\Apple\Mobile Device Support folder.
There have been some issues with this and other dlls not being in the right place (or not being everywhere they should be) since the 10.3.1.55 iTunes update.
However, I note that the 10.4 iTunes update is now out - surprisingly quickly - so try installing that, rebooting, and see if your issue is solved.
If it isn't, though, here's the manual fix:-
With Windows Explorer, navigate to your C:\Program Files\Common Files\Apple\Apple Application Support folder.
Copy the libmxl2.dll that you should find there, navigate to the nearby Mobile Device Support folder, and Paste it in there also.
Reboot and see if all is well.
I actually had the issue with SQLite3.dll, and the above fix worked for me (I found it in an April 2010 posting!).
I passed on the fix as above for the similar issue with libmxl2.dll to someone who had exactly your problem, and he reported that it fixed it for him.

Firefox.exe - entry point not found The Procedure entry point GetLogicalProcessorInformation could not be located in the dynamic link library Kernel32.dll

Here's my problem, until yesterday my firefox browser is fine, unless sometimes when i playing games/app in facebook the plugin keep crashing but thats okay i can stop it and reload my firefox.
But now everytime i try to open firefox it displaying the error massage:
firefox.exe - entry point not found
The Procedure entry point GetLogicalProcessorInformation could not be located in the dynamic link library Kernel32.dll
I try to uninstall firefox, and reinstall again.
i have to use internet explorer and torch browser, which don't fit me and make me in pain.
i try to run in firefox safe mode, according to some suggestion here, but it wouldn't allow me to open Safe Mode (i even holding the Shift button when clicking on firefix icon)
Can you guys help me in here?
Iam using windows xp.
Thank you so much in advance, GBU all :)

hi, do you have service pack 3 installed on your xp computer?

Window 10 build 10041 does not work with Intel 82579V Gigabit Ethernet on ASUS motherboard

I originally posted this question here:
answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_update/window-10-build-10041-does-not-work-with-intel/6729892f-83aa-4822-b20a-ea84f4fd06c7
and was asked to post it on this forum...
I updated a computer I have which is a quad core i7 that I built and includes an ASUS motherboard with Intel 82579V Gigabit Ethernet built in. Windows 10 preview 9926 worked fine with this network adapter. Window 10 build 10041 does not, and I have tried
it twice so far. I even went as far as buying a Thunderbolt-Gigabit Ethernet Adapter (Broadcom, sold by Apple)... and while it installed the driver automatically, it did not work either. Each time you try to view the properties of either of them, it locks
up or give an error. In fact, doing much of anything with the Intel adapter icon assures you of not being able to do a clean reboot... have to kill power. I have finally gone back the previous version 9926, which has its issues but no where near as bad
as not having any network connectivity! Does anyone have this issue and a workaround?
Note, there are two images on the windows 10 preview forum that I posted this question on. I could not post the full link as I was getting a message here that links and graphics are not allowed.

Thanks Roger, I posted the following yesterday in the other thread (thinking it was this thread - confusing after they moved it here)... It may be that the new driver fixes the issue that 10041 has with it, but I have not tried that yet. If I do I will update
this... Thanks!
I have more information about this, which basically exonerates any issue with the Intel 82579V Gigabit Ethernet hardware or software. I have 3 computers with Windows 10 preview so I have multiple angles to see issues from. With this I have found a culprit
(but I suspect not just the only culprit) in this above mentioned problem...
10041 build combined with installing (or attempting to install) CISCO VPN Windows 7 64bit 5.0.07.0440-k9 client causes the issue mentioned above. I confirmed this on a completely different machine with a totally different Ethernet adapter. First machine
is an ASUS motherboard in a tower system I built, with the Intel 82579V Gigabit Ethernet hardware built in. Second machine is a Gateway Laptop from 2008 which has a Marvell Yukon 88E8057 PCI-E Gigabit adapter built in. Build 10041 will work fine with my 2008
laptop, including the MS VPN client (which I have tested). However, if you attempt to install or even uninstall the Cisco client you will have to do a recovery to a restore point (as I have done twice) in order to get your network working again. Installing
or attempting to install (because it never even does install properly and times out), CISCO VPN client will render your entire network unusable. Going back to a restore point saved me and I am still running 10041 but I can't use CISCO VPN client any longer.
I could with build 9926, including on all 3 machines. I now have 9926 on two machines and 10041 on only the 2008 laptop.
Hopefully this above information helps someone resolve the issue. I will also mention, even though my network is working on the 2008 laptop, I still can't go into the Control Panel\Network and Internet\Network Connections and right mouse click on the Marvell
Yukon 88E8057 PCI-E Gigabit adapter icon. I get an error when clicking on Properties menu popup : "An unexpected error has occurred". So something is still up with my network adapter driver or windows software, but it could be a side effect of all
that has happened with the Cisco software install attempts under 10041.
Another note: CISCO Anyconnect also has the issue.

I have a problem with ( AppleSyncNotifier.exe - Entry Point Not Found ) The procedure entry point sqlite3_wal_checkpoint could not be locate in the dynamic link library SWLite3.dll.

I have a problem with ( AppleSyncNotifier.exe - Entry Point Not Found ) The procedure entry point sqlite3_wal_checkpoint could not be locate in the dynamic link library SWLite3.dll.

With Windows Explorer, navigate to your C:\Program Files\Common Files\Apple\Apple Application Support folder.
Copy the SQLite3.dll that you should find there, navigate to the nearby Mobile Device Support folder, and Paste it in there also.
Reboot and see if all is well
In case that your OS is Windows 7 (64 bit)
1. Open windows explorer, go to location C:\Program Files (x86)\Common Files\Apple\Apple Application Support
2. Copy file "SQLite3.dll"
3. Open new windows explorer, to to location C:\Program Files (x86)\Common Files\Apple\Mobile Device Support
4. Paste file "SQLite3.dll" to the location.
5. Reboot your computer, it should not display that message, it should be clear.
Good Luck

Since upgrade to Windows 8.1, ICloud does not work

Since upgrade to Windows 8.1, ICloud does not work. I could click on buttons for Reminders, Notes, etc. and would take me into ICloud to share with other devices. No longer functions.

Hi:
I can't help you with why your PC won't upgrade to W8.1, but I can tell you that if you manage to get W8.1 to install, you won't be able to get the graphics to work anymore.
There is no W8.1 driver for the graphics setup in your PC.
So maybe it is a good thing that you can't get it to work.

Harddisk not found by Windows-XP-Setup + RnR does not work at all !?!

Similar Messages

Maybe you are looking for