Harddrive LED wont work on K8N Neo2 Platinum???

Hey guys, my system seems to be runnning perfectly fine except that all my led's seem to work except my harddrive
Now my board already came with v1.4 so i know i have the latest bios update. so any ideas on why its not working? and oh yeah, if i put the cable on backwards the light STAYS on!!!

Quote from: fafner on 18-February-05, 11:52:46
Reverse the LED jumpers on the MB. The polarity has to be correct for the LED to work.
Ok well how do i do that? i tired putting the cable on the opposite way that its suppost to go on and the light just stays on....

Similar Messages

How to get 2 lans ports working on K8N Neo2 platinum

I can only get the one lan port working which is the realtek device. Ive tried installing drivers for the marvel lan but it doesnt show up in device manager. Can any one tell me how i get this second lan port working.

Quote from: Justmeto on 02-July-06, 05:02:54
I can only get the one lan port working which is the realtek device. Ive tried installing drivers for the marvel lan but it doesnt show up in device manager. Can any one tell me how i get this second lan port working.
The other network interface is by nVidia -- the Marvel part is just the PHY for the nForce3 NI -- and the drivers should install with the nVidia driver install. Which nVidia driver package are you using? People have had NI trouble with the 5.11 pack - personally I use the 5.10 pack with the 4.79 IDE/SATA drivers which you should be able to find here: [urlhttp://downloads.guru3d.com/download.php?id=19[/url]. In BIOS Setup under Integrated Peripherals, what's labeled MAC Lan(nVIDIA) is the one you want to make sure is on Auto.

K8N Neo2 Platinum wont start up

After installing a new K8N Neo2 it worked perfectly for 1 day, no problems at all.
The day after nothing happened. When the psu is turned on it only gives a short flash on the leds, the fans turns for a second and then everything is of.
Have tried with only the most necessary connected to the psu, switched to only 1 RAM in different positions etc. Have cleared cmos every time.
D bracket leds are showing 4 reds for a short second and some times two greens diagonal upper left to lower right and the other two are red.
Any ideas???
Spec;
AMD Athlon64 3500+
K8N Neo2 Platinum
NX6800 Geforce 6800GT
WD Raptor 740GD 74G ( x2 )
Corsair CMX256A-3200LL ( x4 )
Antec True 480P ( 5V-38A, 12V-22A, 3,3V-30A )

Hi,
Its a common problem with this board... different theories are abound as to what causes it, an RMA might not help you
False Starts on MSI K8N Neo2 Platinum

Desperate: K8N Neo2 Platinum won't work!!

Bought myself a new motherboard, processor and memory and it just won't work!
Searched this forum for a solution, but haven't found one yet.
Try to install Windows XP, but it just won't start.
I now get an error code 0x80040507.
Before that, it just rebooted again and again.
My configuration:
MSI K8N Neo2 Platinum
AMD Athlon 64 3500+ Winchester core
2x512 Corsair Twinx1024-3200
Prim. master: HDD 40 Gb Seagate U100/72 ATA
Prim. slave : DVD-RW NEC ND-3500
Sec. master : HDD 160 Gb Maxtor Diamond Max Plus 9 ATA
Sec. slave : DVD-R from LG
PSU: Antec 350W, model SL350P (+5V=35A, +12V=16A, +3,3V=28A, -5V=0,5A, -12V=0,8A, +5V=2.0A)
Sapphire 9800 Atlantis Pro 128Mb
PCI-1 : empty
PCI-2 : Hauppauge WinTV PVR250
PCI-3 : Linksys wireless network card (model WMP11)
PCI-4 : Creative Soundcard SB Live 1024
Do I need a new PSU?? or is there another problem?

AMD recommends a PSU with atleast 24a on the 12v rail. This does not mean your PSU won't hack it, it just means that as a rule of thumb, it's not supposed to.
Could your PSU be the cause of your problem? Possibly! You have a lot of components drawing power from your PSU. It would be wise to buy a beefier PSU with 12v/5v/3.3v amps all in the 32+ range (see my PSU in my signature or the enermax 460/465w whisper II)).
The problem with not having a better PSU to work with is you could encounter an error, deem it as a result of something it's not, and think the PSU is good and something is bad when it's really the other way around. Moral to the story: get a new PSU.
I tried searching microsoft's knowledge base for your error and nothing turned up that had anything to do with windows installation errors. Are you sure you copied the error down correctly?
If so, the only recommendation I have for you is this. Try installing windows with minimal components installed (CPU, motherboard, videocard, single cdrom, single hard drive). Leave your SB Live! out. Leave your WinTV out. Leave your linksys card out. Leave your DVD-R from LG out. And if you are willing to conserve even more power. If you really want to conserve power, you can install windows with only one stick of ram installed.
Next thing you want to do is check to make sure the memory is not faulty. Start by putting only one stick of memory in slot one and testing it using memtest86+ (i hope that link is correct). You're going to want to run a 1-4 hour standard loop of tests followed by a 12-24 hour loop of test 5. Then you will do the same thing with stick two in slot one. After this works, test to make sure there's nothing wrong with the motherboard by doing the exact same tests again one by one with the sticks in slot two this time around. After this is all done, do the tests again with both sticks in slots one and two. if it doesn't work like this, you could have faulty memory (but this should work). You can always run your memory in the same colored slots (single channel (slots one and three)) but this will cause you to take a hit in performance. Generally, for all instensive purposes, you should be able to run it in dual channel mode without any problems. I imagine you will be able to if the sticks are good.
If they don't work in dual channel mode, to be completely honest, I don't know what you would consider the problem then... could be the PSU... could be a badly matched pair... could be the motherboard. All this is determined by how you handled the parts when installing them. There are a lot of unknowns when trying to help a user without knowing anything about their install.
If all memtests' run successfully, you are now ready to install windows. If windows doesn't install correctly, you probably have a botched BIOS setting somewhere (like aggressive memory timings) or something similiar that's stopping you from successfully installing windows.
Buy a new PSU

K8N NEO2 PLATINUM HANGS WITH NVIDIA, WORKS WITH ATI???????????

HI
I have endless problems with nivida cards on a MSI K8N NEO2 PLATINUM board. I have tried 4 different nvidia cards and they all hang on any 3D app or game. NFSU2 looks like it lags in the menu already. It stops for 2 sec then goes again for about 10 secs.
Slot in any ATI grachics card and it works 100% for hours with no problems. I am runnig a 480W Antec psu aslo, so there is no power problem.
Anybody have any idea???????????????????

well..i tried to oc my vid with 78.01 my comp rebooted in just a few seconds of game play...so i reset clock speeds to stock...got rid of 78.01's and installed 80.40 betas...so far so good..and i got this email replay from BFG asking for any fixes..here's a summary of what they said
"If you check the HardOCP forums as well as many others, issues with NF3 chipset motherboards are rampant. They seem to be limited to the implementation of a 64-bit processor with AGP architecture cards, fast ones in particular, but NOT limited to NVIDIA cards. People with fast ATI cards have the same issues... so don't act without investigating.
We have no point of action we can do for you in the matter. The chipset and drivers for it are made by NVIDIA, then implemented by different companies on their products. The exact same can be said for the GPU, chipset on the graphics cards and drivers for them. We're a manufacturer who uses their technology and unified drivers for our cards, but we make "OC" cards that run faster than NVIDIA designed their GPU and chips to run. NVIDIA can't control "how" the companies implement their technology, but makes every effort to create drivers to accommodate issues that crop up during the product 'life-cycle'."
ill say this...i personally havent seen anyone with an ATI having this issue..if anyone knows of that...please let me know...as much as i bashed ATI....i feel like im left with no choice but to buy one(x850xt pe)if no one plans on fixing this for us..any imput is appreciated

MSI K8N Neo2 Platinum cant upgrade to BIOS 1.4, Windows wont boot.

Hello
I have a MSI K8N Neo2 Platinum and I cant upgrade to BIOS 1.4. I have tried everything and cannot get Windows XP to boot with BIOS 1.4.
I have reset the BIOS, set defaults, cleared the battery etc but when I load BIOS 1.4 (from a 98SE an ME boot dish and even from the Live Update?
The only solution is to rebuild Windows after loading BIOS 1.4???
Help

Hi !
Well, I have that problem, too. I think the reason is a new RAID-BIOS-Version built in the BIOS-Update. I´ve tried the beta-versions V1.51 and V1.5X, too - but they won´t run anyway.
My WinXp hangs while booting (before the WINDOWS-XP-Logo appears, or while fading in...). I cannot reinstall Windows completely because, when I install the 2 raid-drivers, the installation routine hangs before the licensetext - when I don´t install the drivers i cannont install on the raid-drive (beacuase the installation routine shows 2 hdds).
I think, a new driver will solve this problem, but I don´t know where to find it....
A.

IS my MSI K8N Neo2 Platinum FRIED!??

Ok I am assembling my first computer right now. I have the Motherboard (msi K8N Neo2 Platinum nForce 3 Ultra Socket 939) a gig of corsair pc3200 RAM, a Samsung 7200RPM hardrive, a Samsung DOuble layer CD/DVD burner, 5 fans, and AMD Athlon 64 3500+ (NCC). But when I plug everything into the motherboard, all the fans start spinning everything looks like its ine except the IDE ports. My CD-ROM wont go on and I just got it! everything is new out of the box. I have a single drive, the IDE ribbon conecting from the motherboard, then the master connecting to the CD-ROM. The jumper is still in there. The "system part" of the IDE ribbon is plugged into the IDE-1 on the motherboard. And my harddrive is SATA, when I plug that in, it doesnt look like its working either! All my power cables are fine because when I plug them into the fans they work...any suggestions?

Yapyap,
would have been nice to post solution.
Drop Ht from 5 to 4 in bios - cell menu as soon as you can get into bios.
How to clear the CMOS
1) disconnect the power cable.
2) push the power button to drain the capacitors
3) Move the CMOS jumper to the clear position, from it's original 1-2 position to 2-3
4) Wait a minute to be sure the CMOS has been cleared. Take your Time
5) Return the CMOS jumper to it's original position 1-2
6) Plug in power cable.
7)restart computer
8) enter bios and select load optimized Bios defaults - save & exit
9) let pc reboot, if you have any settings you want changing do them now.
like HT Settings hard disk boot order etc.,
10) hopefully youll boot

K8N Neo2 Platinum is dead?!?

Hi all!
I've got a problem with my computer. After sending it to Standby, it wouldn't start again. AT ALL! There is nothing happening when I press the power button, even after disconnecting the power. Just the Power-LED is on, everything else stays quiet. No fans, no harddrives, no beeps...
I already tried another power supply, didn't help. I also unmounted everything from my mobo except the CPU, but still no result. It just won't do anything. ??? If it would at least tell my something with some error codes from the speaker or the D-Bracket...
Has somebody got any clue what is happening?
System:
K8N Neo2 Platinum
A64 3200+ Venice E6
4x512 MB Corsair VS
ATI R9800 Pro
I would really appreciate help!
Greetings,
Kristofer

Quote from: Schwede on 20-May-06, 17:38:49
Well, I'm gonna. Doesn't leave me much choice, but first I will test my CPU on someone elses board.
Nice illustration
Since I have to swap my mobo, I will upgrade to an nForce4 anyway and get a new graphics card (actually I ordered already ).
Then I have to get a new PSU anyway.
However since I cannot do this within the next 3 weeks, I am still trying to get my system running.
Well, if you have a mobo to try the CPU in, great, that's a good way to rule that out. If I had that option available, I would lean towards just swapping out the board since I am already going to have both machines basically torn apart. I usually don't swap CPU's without taking the whole board out of the case and POST testing it before mounting. I think that would tell me more than just taking my CPU out and putting it in another machine...but that's me.
The 939 & 754 sockets are much easier to deal with as opposed to the Socket A when the board is still mounted. I've seen bad things happen by not having the right angles and room to work in...
It all really depends on your scenario and what's available to you. Sometimes we are limited in our options since we don't have an inventory as enthusiasts opposed to a system builder. Not to mention the hassle of bringing your gear somewhere or having a friend bringing theirs to you.
Just remember if you are using a different chipset, not to let it try and boot to the OS. Really, all you need to do is see if will POST.
That metaphor is my favorite and gets the point across rather well

K8N-Neo2 Platinum pauses for 25 sec at boot, nvatabus.sys the problem?

All,
After POSTing normally and starting to load Windows XP, my system halts at the Windows XP splash screen for about 25 seconds. Nothing happens, no disk activity or anything, the system just sits there.
I used Microsoft's Bootvis utility to see what was happening. It turns out that the nvatabus.sys driver consumes 100% CPU at boot for 25 seconds then the system continues to boot normally. Does anyone else see anything like this?
I am running the latest nForce drivers from MSI. The driver in question:
NVIDIA nForce3 Serial ATA Controller 2.6
Driver Date 6/3/2004
c:\WINDOWS\System32\DRIVERS\nvatabus.sys 5.10.2600.0446
Windows XP SP1
I have a RAID1 of two 160 GB SATA drives. The mirror is healthy and working fine.
After booting the system is rock-solid stable, no problems there. It's just this unexplained pause at boot. Does anyone have any ideas how to fix this?

ok check it out guy's this thing drove me insane all night last night and most of today. I was ready to return everything and give up. But alas all is not lost. Here is the rundown on what i just did.
My Equipment:
Athlon 64 3800+(w/ stock fan)
MSI K8N Neo2 Platinum Socket 939
2X512 Corsair TWINX1024-3200XLPRO ( with the cool led's )
2 SATA HD (1 Maxtor Diamond10 300 GB w/ 16mb cache, 1 Segate 160GB w/8mb cache)
PP&C 425 ATX Deluxe
Radeon 9700 Pro ( cat 4.8 )
Audigy2 ZS
Sony Floppy
Sony 8x52x52x32 DVD Rewrite
I have been reading and reading just like all you guy's. On a few websites i would pick up bits and pieces on what to try. Heres what i did. Upon Boot up i entered the bios. I then went to Cell Soft and adjusted my timings for my memory. I was at 2.5 not 2.75. I then set my speed down to 166. Exited and restarted. Big mistake everything ri=uns terrible slow and my expensive DDR 400 memory was showing up correctly at 333. Rebooted again entered the bios. reset my speed to 400. Then set the Overclock feature to manual. Set my timings at 2,2,5,2 200 and 2.75 volts. After saving settings and exiting I then turned off the computer. As per some other suggestions I moved my Audigy2 to the bottom most pci slot the one above the orange slot. I moved my memory to slots 2 and 4. I moved my SATA to slots 3 and 4. I rebooted went into the bios again and setup all my voltages. CPU was Auto, AGP was max yellow setting. Memory still at 2.75. I disabled the onboard serial and parrallel ports. Rebooted
Fearing the worst,
5 seconds, 10 seconds, windows screen loging prompt. There was nothing wrong at all. It rebooted effortlessly. It re found my Audigy card and wanted driver but that was it. I am going to reboot a few more times and then run sisandra to test. I hope some of this will help you. I post in a few after some of those reboots.

K8N NEO2 PLATINUM ATA-133 Raid ?

Hello,
My question is, is it possible to setup an Ata-133 raid on the K8N NEO2 PLATINUM (as the main boot drive). Currently I have 2 ata-133 drives and I want to upgrade to this board. I looked at the PDF manual and read the forums, but people usally talk about thier Sata drives.
If it is possible to have only a Ata-133 raid setup. How/what is the best way to set it up since there is only a primary and secondary ATA connection on the motherboard. Setup a master / slave on the primary 1 slot ? or put them on thier own channel ? Note, I read somewhere that optical drives ( cdroms,...) may have a problem if they share the channel with a harddrive that is raided. So thats my dilema.
Thanks in advanced,
Jim

Quote from: crossmax03 on 02-August-05, 20:58:06
jim,
did you ever get the RAID setup to work with the IDE drives?
i was trying to connect 2 ata100 drives on the IDE2 or IDE3 ports and the bios will not seem to detect them at all,
but the RAID controller DOES detect them.
however, it will try to boot from the master drive but restarts at the windows XP splash screen, every time.
-brian
Right. If we connect two IDE HDDs on one IDE1 or IDE 2 (as Master & Slave), and plan to set up RAID.Take IDE1 for example, as long as we set up Integrated Peripherals-->Onboard Device-->RAID Config-->IDE Primary Master&Secondary RAID-->Enabled, Save&exit setup; enter RAID bios to set RAID mode, all things would be ok. But if we want to install OS in this RAID, we must press F6 install RAID driver at the beginning of OS installation. If we only use them as normal storage, OS is in other HDD, we should install RAID driver in OS.
Besides, the two HDDs could not appear in Standard CMOS Features any more, which appear in RAID BIOS.

News - BIG PROBLEM - MSI K8N Neo2 Platinum - DOES NOT POWER!!!

Hi to everyone.
I'm a proudly owner of a MSI K8N Neo2 Platinum that in one year gave me no problem until yesterday morning.
I used the computer in the night before and when I finished I turned it off and I went to bed.
Yesterday morning I found the power led blinking (like if the system was in standby), and there was no way to turn the PC on.
I even took off the battery for more than 12 hours and I left only minimal components installed:
the video card (Gainward GeForce 6800),
the psu (Antec TruePower 550W),
1 x 512 MB Ram Crucial Ballistix,
and I checked them into another computer and they work perfectly.
I tried shorting the MB power switch pins with a screwdriver and I've even tried to power on the system without the Memory or the Video Card... I've tried everything that came across my mind with no efforts!!!!
Every time I give power to the MB appens only that the power led starts blinking, but pressing the button the PC doesn't turn on.
PLEASE HELP ME... I really don't know what else to do!!!
Thanks,
Alberto

Quote from: alberto_melita on 20-August-05, 20:14:56
Hi thanks for the answers.
I do have a D-Bracket, but my problem is not that the system does not boot or does not post... my system DOES NOT POWER ON (!!!!), so d-bracket is useless!
When I plug the system power the only thing that happens is that the power led starts blinking (with the system still in soft-off), and if I press the power switch button nothing happens!
I've the bios for 7025 v1.8 and the settings where for OFF on power-loss ond pressing the button (can't rememeber if it was more than 4 sec) was meant to turn off the computer, but considering that I un-powered the pc more than once without the MB battery the settings should be factory default by now.
I went through the Windows-XP shut-down system, and i could not be an electrical problem as I always used the PC with a pretty good UPS unit.
Right now these are the full specs of my sytem:
- MB MSI K8N Neo2 Platinum nForce3 Ultra
- GAINWARD 6800 2600 GLH 256 MB Ram
- PSU Antec TruPower 550 W
- CPU AMD64 3500+ core Winchester @11*210 Mhz (this cpu has never overclocked very well)
- HEATSINK Thermalright XP-90 with a 12 Cm Enermax Fan (CPU temp in always below 55 °C when stressed)
- 1 x 512 Mb RAM Crucial Ballistix DDR400 optimized for MSI K8N Neo2 Platinum
I left only these things inside my computer in the hope that it would turn on... it did not work. I tested each component but the MB, and they work perfectly.
Again...
Thanks for you efforts, any help will be appreciated.
Alberto.
All parts have been tested: CPU/RAM/GFX/PSU/HD/DVD, just not the MOBO ?
Checked if the MOBO is shorting in the case ?
Have you tried using the reset switch as power, on/off switch ? I've seen before when the power switch stops working (lose/bad wire busted spring) after swapping reset to power, then the system turned on. Worth a try, as sending it back to USA won't be cheap. If its over 1 year old it mite not be covered by the re-seller and or MSI. Best to check this out as law and warranty is different from country to country.
Good Luck

Few question above the k8n neo2 platinum and raid

hi
i have for now intel 3.4ghz and asus p4c800dlux and 4 sata drives :
2x36giga wd 10000 raptors in raid 0 (connected to the on board promise sata controller)
2x200giga wd 7200 jd sata that (connected to on bard sata ports)
i order a athlon fx-55 and k8n neo2 platinum for a oc (a have 2x512 corsiar pc4000pro and hydro cool 200 ) and its look that its going to be problem
"SATA ports 1+2 will not maintain a lock and you can and will corrupt hard drives placed on these channels if you raise the HTT above 220mhz."
http://www.madshrimps.be/?action=ge...890&articID=228
so im in a problem, if i wont to do nice oc (and i will) i need to leave sata ports 1 and 2 not connected and buy a sata-pci controller for my 2x200giga , im right ?
in that case i need to connect the raptors in raid 0 in the sata 3-4 prots (near the agp) but:
the raid on the noe2 is "NV RAID (Software)" it means that there is no a controller like promise and the cpu need to replace the controller work, so its doing a lower performance.

If you had 4 huge drives I would be more sympathetic. To me every board is a compromise, resulting in me having to abandon something I might have done previoulsy. In you case ditch the two 36gb drives, and slum it with the 200gb drives. Remember that "overclocking" is not a right. There will be many users oblivious of the SATA 1/2 overclocking problems running 4 sata drives in RAID without a problem.

Sound Issues /w K8N Neo2 Platinum

Hello, I have a K8N Neo2 Platinum and I am having trouble wit the sound. I have installed the drivers on the nForce CD, but I cannot hear anything.
Any suggestions?

You should list what opperating system you're using aswell as the driver version that's giving you trouble, someone might spot a problem and be able to help you more easily, for instance if you're using XPx64 the drivers for XP wont work.
Maybe try downloading the latest version from Here or Here.
Also check in Device Mannager, does it say that there's a problem with your sound device or does it say it's working properly ?

Has the K8N Neo2 Platinum bios poroblem been fixed?

I work at CanadaComputers, and well we've been having this problem w/ people purchasing the K8N Neo2 Platinum, and a 3000+ winchester, mainly because that it wont post becuase the CPU is 90NM, where as the bios that is shipped w/ the board only supports 130NM.
I was just wondering if that was fixed or something because people that still buy the board from us, have this problem. Are we getting just the older versions of the board (the june build i think?) or has the problem just not been looked into?
Luis

Interesting that you work there. I bought an MSI K8N Neo2 Platinum and AMD64 3000+ . How are people finding the Asus A8V DX and Epox 9nda3+? Any problems? I may sell my MSI and grab one of those, and actually could easily get it from CC. I don't care if I lose on total speed etc. I want stability and less problems. I haven't even put my PC together and gotten it up and running and the list of potential problems is daunting. That and the fact that I happen to have a Matrox G400 video card which won't even allow me to start my PC! Arrghh. Either that or grab a Sapphire 9600XT even though I hardly play games.

MOVED: K8N Neo2 Platinum, wich cpucooler?

This topic has been moved to AMD64 nVidia Based board.
K8N Neo2 Platinum, wich cpucooler?

Quote from: hansh on 02-January-06, 18:43:45
Yes, it will fit and it is working very good
The only problem I could think of is that higher memory modules, like the Corsair Pro with leds) might not fit ... with "normal" modules there is no problem.
thanks!
now I'm a happy boy
I have "normal memory modules" so thats cool :p

Harddrive LED wont work on K8N Neo2 Platinum???

Similar Messages

Maybe you are looking for