"HARDWARE NOT DETECTED.." when try to update LiveDrvUni-pack(E

Hello,

I had Blaster Li've 5. installed was worked perfectly until XP-SP2 installed it's got some sound problems so I decided to check my sound card for update then I try to update Li'veDrvUni-pack(ENG) and I got message that my sound card is not found. I used diagnostic is failed "Hardware not Detected". But is weird that I reinstalled software from original CD and check back with diagnostic it's worked then failed again. I tried too many ways but still not detect, here how I did some...
- Re-installed software and removed card.
- Re-installed card after computer run completed process without a
 card. Then reboot twice.
- I have Intel 8280BA audio controller and Unimodem Half-Duplex
 audio device build-In my system board I disabled them.
- Updated Drivers and shown working properly.
One thing I could not understand that my sound system working fine and Devices Manager shown hardware working properly and I tested my speakers is working (I had Creative 5. speakers) why I could not update software due to hardware does not detected. That had worked well with XP-SP. I doesn't know is that caused by SP2 or else's.So if anyone has some kind like this problem please helps me that would appreciate.

let me ask you when you install your new dri've your sound card was in the slot or nothing was there beside your video card, i had this problem, i install fresh windows with nothing else and use lowest slot for the sound card and then restart the pc works perfect , try that see if that works good luck,
RON

Similar Messages

HDCP hardware not detected when purchasing HD movie

Both my AMD Radeon HD 6670 video card as well as my LG L245WP-BN monitor support HDCP. However, each time I try to rent or buy a HD movie from the iTunes Store, I get a warning saying that my computer does not support HDCP and I need to get the SD version. Prior to updating to iTunes version 11 I already successfully downloaded 1080p HD and HD-SD movies and TV shows onto my Win7 Pro 64-bit PC. What could the problem be?

you cannot purchase HD content. HD content is only available to rent and is restricted to appletv only.
in accordance with the rental DRM rules, they auto-delete after 30 days if not watched. if watched 24 hours or 48 hours depending where you are.

"IR Hardware Not Detected" message when trying to set up TV on Idea Center A700

When I am trying to set up my computer to get TV from my set top box the computer identifies my signal and shows a small picture of the live TV. When I click on next I get a message - IR Hardware not detected. Can someone please tell me to what this refers? My wireless remote works and the set top box has an IR cable that is only a few feet away. My TV remote picks it up easily. Is there more hardware that needs to be bought for the TV to work with this computer?
Thanks,
David

Ok, I have now gotten Reader 10 installed, can open files from my desktop but IE 9 keeps crashing when I try to open PDF files even though I exited and relaunched IE 9. I did take ownership of all the folders containing Reader 10 and then clicked OK when I got the error notice about the shortcut being installed. I did make a copy of the crash error report and it reads as follows:
Problem signature:
Problem Event Name: APPCRASH
Application Name: iexplore.exe
Application Version: 9.0.8112.16421
Application Timestamp: 4d76255d
Fault Module Name: IEFRAME.dll
Fault Module Version: 9.0.8112.16440
Fault Module Timestamp: 4eb319a7
Exception Code: c0000005
Exception Offset: 001b174b
OS Version: 6.1.7601.2.1.0.768.3
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789
Read our privacy statement online:
Any help is greatly appreciated!

When try to update apps its says need to go to Bavarian store Do not have account. How do I get to the right store. (United States)

When try to update apps it says do not have account need to go to Bavarian store. Need jot get to United States store. How?

Can you post the exact message you get please. As far as I know, there is no "Bavarian" store (unless you are talking about an import store with merchandise from Bavaria).
Are you trying to go to the Mac App Store (for Mac OS) or the app store for iPhones, iPads, etc???
And, we need to have more information: what Mac computer or i-Device are you on? What version of the OS?

Why do I keep getting actionlist not found when trying to update to version 11.6.602.180?

WHy do I keep getting actionlist not found when trying to update to update to version 11.6.602.180?

This problem and others are outlined in this help document. In addition, please try installing from the appropriate stand alone Windows installers located here:
Installation Problems - Flash Player - Windows

X-fi fatal1ty device not detected when running speaker selection wizard

Gx-fi fatalty device not detected when running speaker selection wizard? ?
System is a custom build, based off an ASUS A8N-SLI Premium, with two GTX7800 display cards. in a SLI configuration
Fresh installation fo Windows XP Profesional with SP3 slipstreamed.
Origional CD fails to detect the card, claiming a supported device is not present.
This card has worked prevously, and is verified as fully functional in windows Vista. ?
Please note Windows Vista can not be used.
I have tried about 30 different versions of the drivers (each on a clean installation) and used both clean and dirty boots, and nothing is working.
Before anyone points me at other threads in this forum, please note i have been scouring this forum for the past week trying every sugestion there is, and I have raised a ticket with Creative (who despite the prommise of a 2 day responce, have yet to respond)
I have tired multiple versions of the NForce drivers, NVidia display drivers, Creative Drivers, Bios updates, Chipset hacks and more.
does anyone hav a sugestion that is not already posted on this forum.

Tried it on one of the spare PC's in the house earlier (Nforce 2 based) - still no recognition of the card whatsoever, it's as if it doesn't exist.
I'm guessing that the card is pretty much toasted eh?
--Jakk

Trojan horse when try to update flash player !?

this trojan warning( trojan horse crupt.tbj and trojan horse Pakes_c.BVTU
), from AVG ,occurs when try to update flash player,
the AVG antivirus deletes.
Problem started when cannot access IE, Firefox, or chrome....get same error.....”flash player out of date”,
then opens download,
but then when try to download,AVG blocks it
Not only on Desktop,but also on my iPad, off the same network router.
Any solutions ,advice?

joejazz wrote:
”flash player out of date”
Can you post a screenshot of what you see: https://forums.adobe.com/thread/1070933
Where does that "error" lead you to download? Anywhere else than an adobe.com or macromedia.com website is not an Adobe update.

Running OX 10.7.4 and can't open iPhoto 9.0 window keeps popping up saying to update software then when try to update it says software is up to date

Running OX 10.7.4 and can't open iPhoto 9.0 window keeps popping up saying to update software then when try to update it says software is up to date

What version of iPhoto do you have (9.0 is the original version from a couple of years ago - you should be way past that - at least 9.1 - probably 9.2 - maybe 9.3)
Download the 9.1 update and install - http://support.apple.com/kb/DL1322
LN

ITunes goes into (not responding) when tries to update library

How can i get my mac around this problem? iTunes goes into (not responding) when tries to update library

I just posted with the same question

TS1702 Apps will not download when I hit update, why is this?

Apps will not download when I hit update, why is this?

hello zombiasnow, adobe has announced in late 2011 that it will cease any further developement of flash on mobile devices, so now that's kind of a dead technology on mobile. if you have a complaint about a third party product, you'll have to put that to the vendor of this device (amazon in your case). the firefox support forum isn't the right place for such a discussion.
thank you for your understanding!

TS3694 got error code when try to update my ipad 2

keep getting 3194 error massage when try to update to ios 511

Have you got the latest version of iTunes on your computer : error 3194 ?

Hi,why I have a "DMA hardware error detected" when I try to save file as *.htm for remote front panel application?

Hi,
I try to learn how to present my data anywhere by using labview remote front panels. I use PCI-mio-16E-4 device to acquire data. After I start web server and try to save to as *.htm file, I got the "DMA hardware error detected" message. Can anyone help me to solve the problem. Thanks.

What was the actual error code?
Copyright © 2004-2015 Christopher G. Relf. Some Rights Reserved. This posting is licensed under a Creative Commons Attribution 2.5 License.

IPad does not detected by iTunes on Updated Windows 7

Hi All,
Since i updated my MS Windows 7 with the latest patches, my iPad can not detected by iTunes on my PC.
The USB ports on my PC were fine, the peripheral (eksternal HDD; USB Flash disk; Printer) still working fine.
The USB sinc cable data is also working fine when i charge the iPad directly from wall mounth port.
Do you have a same experience?
Please advise....
Thanks and regards

Folks,
I had this problem with my PC (windows 7, 64-bit) and my iPad. After messing with it for a long time, I finally found the answer (bad USB driver). The following two step process should help resolve these kinds of problems more quickly.
The first step is to verify that the iPad (or iPhone) is really connected to your computer. This can be (really) checked using a program called USBDeview. You can get this (very small) program from http://download.cnet.com/USBDeview/3000-2094_4-10614190.html or http://www.nirsoft.net/utils/usb_devices_view.html. Don't worry, it's not Spyware or Malware.
Just run the program and sort on the 'Connected' column. If your iPad or iPhone doesn't show up as Yes (under 'Connected') then your iDevice is not properly connected to your computer. Could be a cable problem. Could be an iDevice problem. Could be a USB hub problem. Note that your iDevice might be listed as what it is (iPad or iPhone) or it might be listed as 'Apple Mobile Device USB Driver' in the 'Description' column.
Apple has a number of ideas to resolve this sort of basic connectivity issue, including switching USB ports, resetting your iDevice, rebooting your iDevice, rebooting your computer, etc. You will need to try them until your iDevice shows up in USBDeview as 'Yes' under Connected.
If you iDevice shows up as 'Yes' under connected, it should also be visible in the Device Manager (found in the Windows 7 Control Panel under Hardware and Sound). You might find it under Portable Devices or it might be under Universal Serial Bus controllers.
The iDevice may or may not show up in the Windows Explorer. On some machines it does, on others it does not. Why is not clear.
If the Idevice is properly known to Windows and iTunes can't see it, then any number of other things could be wrong. Apple has a list. See the very useful page over at http://support.apple.com/kb/TS1538. Testing shows that the Apple Mobile Device service must be running. Check this using Task Manager (started by right clicking the taskbar). Note that the iPod service and the iphlpsvc service must also be running. These services have different names under the Processes table versus the Services tab of Task Manager.
AppleMobileDeviceService.exe - Apple Mobile Device
iPodService.exe - iPod Service
ItunesHelper.exe - iphlpsvc
Step 4 of http://support.apple.com/kb/TS1538 checks if the Apple Mobile Device USB is installed. This is essential and a common source of problems. In at least some cases, Windows will install the 'MTP USB' driver. Indeed, Windows will reinstall this driver if you uninstall it. The MTP USB driver is essentially a Windows bug (possibly caused by Microsoft). You MUST replace the MTP USB driver with the Apple Mobile Device USB Driver. Step 4 explains how to do this. Note that you MUST use the 'Have Disk' approach. Otherwise, Windows will just reinstall the invalid MTP driver.
The Apple doc indicates that you can find the correct driver at C:\Program Files (x86)\Common Files\Apple\Mobile Device Support\Drivers. Perhaps this is correct on some systems. You may find the correct driver in C:\Program Files\Common Files\Apple\Mobile Device Support\Drivers.
iTunes could make this a lot easier by checking if the iDevice is known to Windows (what USBDevier does) and if the Apple Mobile Device USB driver is properly installed for the iDevice. Sadly it doesn't perform either check. Note that iTunes does if some of the related services (see above) are actually running.

Internet Explorer 9 not showing as not installed when using Windows Update - Error: Code 9C48 Windows Update encountered an unknown error.

I built a few new Windows Server 2008 R2 with SP1 VMs today and ran into a problem where Windows Update is not detecting the fact that Internet Explorer 9 is already installed. Internet Explorer 9 keeps showing up as an available update when
using Windows Update. When I try to install it as a test I get the error message: Code 9C48 Windows Update encountered an unknown error.
My normal build procedures include applying all the patches for the OS prior to any other work on the servers. The way I like to do the patching is to do every update other then IE9 in the begininng and once all the other updates have been
completed, install IE9 and then patch it if there are updates available. I followed this procedure on every build for the last year and I have not run into any issues until today. The only difference today is the latest patches that were released yesterday
April 10th, 2012. To test the theory that it may be one of the latest patches, I reinstalled Windows from scratch making sure to format the disks and then I installed IE9 right after the OS install without any other updates. Once the
server was rebooted, I checked Windows Update and Internet Explorer 9 still showed up as update (Not the Cumulative Update which normally shows up after an IE9 install) and yes, I did make sure to click the 'Check for Updates' link before I looked just
in case. My next test was to patch a couple of the servers I had built prior to April 10th, 2012. Those servers did not have any issues with the latest updates and they are not experiencing the same behavior as the newly built servers.
I ended up comparing the IE9 Version on the cleanly install OS (No updates were installed except IE9) and the servers I built last week which were patched. The versions are exactly the same.
My findings above lead me to believe that there is a problem with the latest IE9 install package (which includes the latest cumulative update) and the Windows Update detection component.
I guess I am looking for someone to report this up the chain to get this fixed so no one else runs into this problem. I know in some cases we may not be able to see additional IE9 updates until this is resolved.

I just started having the same problem.
I was creating a new VM in Vsphere from our 2008 R2 SP1 image and it hasn't been updated and repacked in a while, so i have to install about 60 updates, including IE9.
I went through my normal setup as i had just created 2 VMs and updated them on Monday with no problem.
I got the same error code as you. The install looks like it installed IE9, but the update is still showing up as available in Windows Update.
I deleted the VM, created a new one, chose all updates except IE, then did that and it still shows up again.
Then i deleted the VM, installed just IE 9 and it still shows up as available on reboot.
I have a script that i can use to reset/clear WSUS cache on the computer, (Software distribution folder, and the windows update log, and recreates a certificate), so i tried that and then rebooted and it still showed up.
I then decide ok, maybe the Image got messed up somehow, so i started creating a new 2008 R2 install from scratch last night and chose to update just IE9 as the first install. I did that, rebooted and it didn't show up in Windows Updates, so i though GREAT.
I proceed to kick off the 100+ downloads needed before i left and left the console up.
When i got in to work this morning, the updater seemed stuck on 31 of 102 updates, this one in particular: KB288516. I rebooted the computer, because it wouldn't stop and just seemed stuck since last night, which these updates should only have taken about
an hour to install at most. I log back in and sure enough, it now shows Internet Explorer 9 at the bottom of the update list as being needed for install.
I believe this is Patch Tuesday week, so maybe they screwed up something with the Windows Update detection engine, because it worked fine on Monday when i had to update IE9 on 2 VMs that i created.

Itunes not detecting any device after update to 10.6.3

i have just updated itunes to version 10.6.3 and not it will not detect my iod touch or my ipod classic. i have tried it will an iphone 4 aswell and it is not detecting that either.
i have rebooted my ipods and my computer. i have also uninstalled and reinstalled apple mobile device driver and it still will not detect any devices.
when i try to put my ipod tocuh into recovery mode itune does still not detect it.
my computer dectects my ipod touch and my iphone 4 as still cameras and detects my ipod classic as a usb mass storage device.
any suggestion will be very helpful
thanks

Try removing and reinstaling all the Apple software:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP

"HARDWARE NOT DETECTED.." when try to update LiveDrvUni-pack(E

Similar Messages

Maybe you are looking for