Hardware Test: Video Ram "error code 2NVD/1/4:119" G5 2.7 NVIDIA 6800 Ultra

Wondering if anyone has experienced this . . .
My G5 started displaying rows of chevron shaped artifacts a few weeks after upgrading to Leopard, Bought a used replacent card and it seemed to fix the problem for a couple of weeks then too started displaying the artifacts, ran the Hardware Test on both cards and both had Video Ram error code 2NVD/1/4:2119
I'am reluctant to buy yet another card untill I'am sure its not a Leopard Issue. any ideas?

I need to do more troubleshooting of my problem before I trying to reflash I think . . .
the other day I had a friend install both my original card and the newly purchased "used" card in his G5 and he also got the error codes on both of them. Brought them home installed the replacement card reset the SMU and PRAM as I've done many times before and got the G5 up and running (after several reboots) no artifacts seemed to run perfectly for a couple of hours anyway when I tried restarting and then the problems returned, gets to the grey screen with the rows of artifacts then stops, screen goes black then the fans start slowly spooling up to max RPM (most likley from a kernel panic) logs show;
"Apparent UniNorth Hang: AGP Status"

Similar Messages

  • Video RAM Error code disp/13/2

    Hello again
    Does anyone knows what this means? And if so, how can I fix it?
    My display has been going funny for the past two weeks now and keeps crashing. After I did a hardware test, this came up next to the video RAM:
    Error code disp/13/2
    Now I have no idea what to do next?
    I'm desperate, please help.
    Carly

    That means that you need to take it into an Appple Authorized Service Provider. It is not user servicable.

  • Ran hardware test and found error code 4SNS/1/40000001:YPOR-0.592 ? can't find the signification of this error code

    ran hardware test and found error code 4SNS/1/40000001:YPOR-0.592 ? can't find the signification of this error code.

    Back atcha!

  • Video Ram error detected: 2NVD/1/4:0x6" -?

    Dear Apple users,
    Apple Hardware Test confirmed that I have the following error under Video Ram:
    Video RAM Error Detected
    Error Code 2NVD/1/4:0x6
    Does anyone know what this mean? Do I just get a new video card? Or is this error related to the logic board and needs a major replacement of the motherboard?
    Thank you for any advice beforehand.

    Hi-
    The error is referring to your graphics card VRAM, not a problem with your logic board.
    Do I just get a new video card?
    I would say Yes.

  • Video Ram Error Code

    I ran Hardware Test and got an error for Video Ram. 2ATI/1/4 113xxxxx117
    Can I replace the Video Ram myself? If not, how much does a repair like that cost? RAM is guaranteed for life, right? So how about Video Ram?
    I am getting lines around icons and the cursor. It is imposible to watch any videos in iTunes or FrontRow without enormous graphic interference. Like a really bad connection on your TV.
    Thanks.

    The video RAM is part of the motherboard. It is not something that you can replace yourself. Unfortunately it means that you need a new motherboard.
    FYI, you should ask future questions in the iMac G5 discussion area since you have an iMac G5.

  • Apple Hardware Test detected an error code... now what?

    I ran AHT and I got this message:
    Alert! Apple Hardware Test has detected an error
    4M0T/1/40000003:HDD-1424
    Can anyone shed some light on this?
    My early 2008 iMac has been having issues with the spinning wheel when opening and using applications. I can't seem to pinpoint when it happens, but many times I will have to shut down or power the machine off to stop the wheel of death from spinning.
    Any help would be greatly appreciated.

    bump... any one else?
    I was able to boot the machine up today and I am noticing the top of the machine is getting very hot. Could this be the overheating issue I have read about here in discussions?
    I was also able to transfer files to an old eMac, so I am backed up, but that transfer slowed after the machine warmed up. I would shut the iMac down and let it cool... it then transfered great while cool but slowed when it heated up....
    I am taking it in to a local authorized repair shop Monday morning..... just hoping for some more thoughts before then.
    Thanks!

  • Symptom: iBook typing by itself. Diagnosis: Video Ram Error

    My ibook types by itself sometimes.
    If I run the Apple Hardware Test when the computer is fine then the computer will pass the Apple Hardware Test.
    But, if I run the Apple Hardware Test when the computer is malfunctioning then the computer will fail the Apple Hardware Test.
    Here is the error message:
    Video RAM Error detected
    **ERROR*CODE***ERROR*CODE**
    2ATI/2/4: 113-xxxxx- 1 42
    **ERROR*CODE***ERROR*CODE**
    Is there any genius out there who has a solution?
    I already took my computer to an authorised Apple Service Centre, they told me that I should replace the logic board.
    I live in a developing country. A new logic board is too expensive for me.
    ibook G4   Mac OS X (10.3.7)  

    I'm guessing you actually have two problems. A video RAM problem and a keyboard problem. I can't believe a video RAM problem would reveal itself by typing. The keyboard can be replaced easily, it's a user-replaceable part. I might try to get that replaced first. It shouldn't be too expensive. However, this will not fix the video RAM problem you've detected. You will need to replace the logic board to get that fixed.
    -Doug

  • Video RAM Error Detected

    I've been having major problems with my PowerBook G4 (12", 1.33 Ghz, 1.25 GB RAM, 60 GB HB, Tiger). I just ran the Apple hardware test again. It said that there is a Video RAM Error Detected. Here's the Error Code - 2NYD/1/4: 2086
    Does that make any sense to anyone?
    Thanks!

    It means you need to take your machine in to service if it doesn't fall under these programs:
    http://www.apple.com/support/exchange_repair/powerbook.html
    If the cost is too high, one of these companies may fix it cheaper:
    http://www.dttservice.com/
    http://www.powerbookresq.com/
    http://www.microdocusa.com/
    http://www.macspecialist.com/
    http://www.techrestore.com/
    Or if you can find the part and are technically minded, http://www.ifixit.com and http://www.xlr8yourmac.com/ have numerous logicboard replacement instructions.

  • Video Ram Error Detected Question

    Had my screen lock up and when I ran Apple Hardware Test I received a VIDEO RAM ERROR DETECTED - Error code 2NYD/1/4:2122
    Scrolling is all messed up, tried reinstalling system software but nothing seems to help. Only starts after quite a few tries.
    Do I need to take in for service or is there a software fix?

    Welcome to the discussions Eugene.
    If I were you, I'd take it in for service. It sounds like a hardware problem that a software update won't fix.
    I hope it works out for you.

  • AHT Video Ram Error

    I have been having a string of kernel panics and AHT v1.2 detected a video RAM error "disp/13/2". In a previous post, it was suggested that this message meant that many things were fried and that a new computer was the best option. Has anyone successfully repared this problem, and how do you do it?

    Unfortunately, AHT's very cryptic messages are intended to benefit Apple technicians, not ordinary civilians. That said, any message about a video or display problem is bad news, because it probably means replacing either the logic board or the display, and each is very expensive.

  • Con apple hardware test rilevo questo errore nella memoria 2MEM/1/4 DIMM1/J4001/1/ e qualche altra volta 2MEM/104/4 DIMM1/J4001    ritengo siano problemi ad una delle memorie ram aggiuntive. che debbo fare ? è da sostituire? o c'è un modo di escludere l

    con apple hardware test nel mio IMAC G5, rilevo questo errore nella memoria 2MEM/1/4 DIMM1/J4001/1/ e qualche altra volta 2MEM/104/4 DIMM1/J4001    ritengo siano problemi ad una delle memorie ram aggiuntive. che debbo fare ? è da sostituire? o c'è un modo di escludere il o i banchi di memoria interessati?

  • Freezing Macbook Pro. Graphical glitches and occasional 3 tones on start up. Hardware test shows no errors. Is it RAM or a graphics card on the way out, or software?

    Recently my MacBook Pro has been freezing and showing bad graphical glitches. Multiple restarts eventually fix it and a couple of times the three tones break, three tones break warning has occurred on start up. From what I can find this is usually a RAM error but after doing a hardware check I get the response all is OK. This still happens after the check and I am unsure what the problem could be. Can anyone help? Could it be a memory issue, a hard drive issue, Graphics card issue (drivers are up to date) or is something up with the software. I also have a Bootcamp partition running Windows 7 too and this is a problem that presents itself there too.

    Most likely to be RAM:
    Beeps on startup:
    1 beep = no RAM installed
    2 beeps = incompatible RAM types
    3 beeps = no good banks
    4 beeps = no good boot images.
    5 beeps = processor is not usable
    http://support.apple.com/kb/HT2538
    I would suggest you take it to an Apple Store for a free diagnostic.

  • Video Ram Error

    Hi All,
    Wondered if anyone could advise me?
    I have PowerMac G5, 2x 2Ghz, 2.5GB DDR SDRAM.
    I've upgraded to 4.1.9 and keep software up to date.
    All ran perfectly, until out of the blue, my screen started displaying artifacts. Example:
    ftp://tonyg3d:[email protected]:21//tonygold3d.com/public/Picture.png
    (Copy link into browser)
    Photoshop seems uneffected, but 3d software runs, but is distored as example.
    I ran disk warrior (repaired and fine) I then ran, the Apple Hardware Test from my install disk. I got an error message from the Video Ram; 2 ATI/I/4: 113-A14401-117
    Is there a way to fix this or do i need a new Video Card?
    If so, i was looking at ATI Radeon X1900 XT Graphics Upgrade kit. Is this compatible with my machine?
    Thanks in advance,
    Tony.

    Hi
    If the graphics card has a fan attached, it may be worth checking that it isn't sticking or clogged with dust etc, just incase they're heat related artifacts. Failing that though, assuming it is a geninue hardware problem with the VRAM, I think the only option is to replace the graphics card.
    Compatible cards depend on whether you have a dual processor 2GHz G5 or a dual core 2GHz G5. The former (dual processor) has an 8x AGP graphics card slot, making the Radeon X800 XT the only real choice. The latter (dual core) has a PCI Express graphics card slot, making the Radeon X1900 the only real choice. You can tell them apart by the number of ethernet ports on the back - the dual processor models have one ethernet port, the dual core models have two.
    Unfortunately Mac compatible graphics cards seem to be in short supply at the moment, seemingly because they're being redesigned to conform to the RoHS (Restriction of Hazardous Substances) directive.

  • Freezing G5Quad, Ran Hardware test, result DIMM Error

    Hi,
    I have worked with macs for many years and I had never experienced such a problem. I have 2 Quads, one with 6 Gigs RAM and the other 3 Gigs. The one with 3 started freezing up randomly, sometimes during startup, sometimes after start up, or just after opening a program. The mouse would just freez. I could not do anything.Then I ran Hardware test and it came up with a DIMM error. it said DIMM J9600 had a problem, so I changed the possitions of my RAM and now it is working fine.
    What I would like to know is how does a DIMM go bad. I had not opened my G5 for at least 4 months and it just happened from one day to the next. It also currupted my system disc, which I was only able to fix taking it out from the computer and putting it into my other quad and running Disc Warrior, which took more than two hours to fix.
    Any ideas what must have happened???
    Thanks, and sorry for such a long explanation.

    Well - if you are now not getting the RAM error after switching slots, it seems possible that there was nothing wrong with the RAM and it was re-seating the RAM that fixed it.
    Although the RAM is a tight fit in the slot, there are many small contacts and any contamination can cause problems - which re-seating can fix.
    As you don't report getting the conventional RAM problem warning - bottom of the page here
    http://docs.info.apple.com/article.html?artnum=302527
    it could even be an intermittent fault, so it might be worth running the extended RAM tests - Memtest/Rember - linked-to here
    http://www.thexlab.com/faqs/aht.html

  • Got a Screen named hardware teste and a error msg

    I was playing World of Warcraft,
    i went to sleep, turned the MBP off,
    when i woke up, i turned it on, a diffrent screen apeare named "Hardware Test"
    and give me an error MSG:
    4SNS/1/40000000:TGOD-86.500
    what that means?
    what should i do ?

    Call applecare or take it into an apple store. I got the same error message once, but without the 86.500 part, and ended up having to get my logic board replaced. Only those at apple know exactly what the error codes stand for though, so best to get in contact with them, and I would back up any important data just in case.
    -John

Maybe you are looking for

  • Batch Determination While Goods Issue

    How To Active batch Determination at the time of issue the goods I have done following SPRO setting . Strategy type --> YB01 Inventory managment Search Procedure --> YB001 Allocation IM Search Procedure -->> 261assigned to YB001 along with Active "Ch

  • Bug in Arch/ifconfig?

    It seems that it takes two times to set an IP address with a specific netmask using ifconfig (this works the first time in Ubuntu/RedHat). First attempt sets an IP with an invalid mask (the "Cannot assign requested address" does not always show). Sec

  • Photoshop Elements/Premiere 10 Installation

    What is the purpose of Disk 4 & 5 in Photoshop Elements/Premiere 10 package. Loaded just fine from Disk 2.

  • Cannot recolor artwork for all objects in Vector?

    Hello All, I used Live Trace to create a Vector. On some of the objects in Vector I can recolor artwork, but others there is no options to recolor. Does anyone know why and is it possible to see recolor options for all objects?

  • Problem installing Illustrator CS5.5. because of resolution.

    I have a problem installing Illustrator CS5.5. on a laptop with an Intel HD4400. The error message is that the resolution is too low, despite the fact that the resolution is 3200x1800. What to do?