Has 10.8.3 broken Canon Lide 100 driver?

My Canon Lide 100 scanner powered by MP Navigator EX software no longer works after installation of 10.8.3. The error message says that the relevant driver is not installed. Even after re-installation of the latest available software the same error appears. Any suggestions as to a workaround?

Just to be clear when you say you downloaded the latest software, you downloaded MP Navigator EX 2.0.6 and MP Navigator EX 2.0 Opener from the Canon website? If you did and it doesn't work then you will probably have to wait for Canon to update the software.

Similar Messages

Canon LiDE 100 does not respond after wake from sleep

I have a Canon LiDE 100 flatbed scanner. I constantly put my iMac to sleep and only ever shut it down once every few weeks.
When the computer wakes from sleep the scanner does not respond. Image Capture lists the scanner in the device list but reports the following error;
"An error occurred whilst communicating with the scanner"
I have to unplug the USB cable and plug it back in for it to work (or restart the computer, both always work).
Since I only moved to the Macintosh in July I have no idea how to uninstall drivers to give myself a fresh start and the scanner does not come with an uninstall utility.
Any suggestions on how to fix this little problem?
Thanks.

I am going to respond to my self and say I am nuts.
Canon does not seem to have any uninstaller for this scanner on their site:
http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=DownloadDet ailTabAct&fcategoryid=351&modelid=17104
Which is rather odd since they have installers. this is different from most of their other older scanners. But if you just plugged in our scanner and things worked in OSX, which it should have, then you should be OK.
However I can confirm that others see this issue (like my dad) and here is the official Canon response to the issue:
+Dear XXXX:+
+In some cases, coming out of sleep mode may not properly reinitialize+
+the USB bus on Macintosh Operating Systems. Unfortunately, the only+
+work around when this happens is to restart the computer.+
Of course this in not exactly true as logging out and back in fixes it.

Canoscan LIDE 100 platen not moving

My canon LIDE 100 scanner was working perfectly, but after a recent move, stopped. The scanner is present in About my Mac, and responds to calls but makes a short grinding noise and then a driver communication error pops up. I tried the scanner under Windows 7 in Parallels Desktop with the same results. I would chalk this up to a hardware problem, but I had a LIDE 35 last year that I chucked for the same reason. Any ideas? thx!!!
coocoo

The LiDE scanners have a lock switch underneath. These are On from factory and have been known to move enough to lock the contact sensor when transported.
If the lock is Off then it does sound like a hardware problem - again

Canon Lide Scanner not shown as import option Elements 10

I'm using windows 7 and a trial version of Elements 10. On my version of Elements 9 my Canon Lide 100 shows as an import option but it is not available in Elements 10. In the Elements 10 organizer I see options in preferences for selecting a scanner but nothing in the editor about scanners.
I don't remember having to do anything special in Elements 7 or 9 to get the scanner to work.
I was going to purchase the upgrade to 10 tomorrow, but I'm not sure I want to if the scanner doesn't work.
Patt Ricketts

If your scanner requires the twain interface you may need to move the file from the optional plug-ins to the plug-ins folder.
See also:
http://help.adobe.com/en_US/elementsorganizer/using/WS54A09625-5476-4dd7-B78E-C39D462C93A6 _WIN.html

Canon Lide 30 Trouble Fix

Wanted to share this solution as we COULD NOT scan to Image Capture or Canoscan Toolbox 5, on Leopard, with our old Canon Lide 30 scanner.
We did find an old version of Canoscan Toolbox X (4.1.3) and IT WORKED like a charm with Leopard. We scanned 100 photos into JPEGs using the toolbox alone.
Don't know where you can find a scan of toolbox x 4.1.3 online, but if I find it, I'll addend a link.

Thank you so much. Several topics that came up when I googled the scanner declared that Canon Lide 30 with MacOS 10x was a dead-end trip. Following are more explicit instructions for newer Mac users.
1) make sure that users have read/write permissions in Macintosh HD/Library/CFMSupport (find this folder and command-I it to change permissions) Found this tidbit on another website.
2) download the Canon scan toolbox http://www.versiontracker.com/dyn/moreinfo/macosx/16292&mode=feedback&vid=84900
3) unstuff it. You might need to download StuffitExpander to do this.
http://my.smithmicro.com/mac/stuffitexpander/download.html
4) Finish the Canon toolbox installation
5) Download the most recent driver for Lide 30 from Canon's website. (this might change so log on yourself.)
I did not try the latest version of toolbox after I corrected the read/write permissions so, perhaps, Canon has fixed this. Who knows?
I have been able to scan everything I have wanted so far. Thanks again.
BTW: I changed to the iMac from HP & Vista because I was unable to use much of my computer investments after my XP system was stolen. I have been able to use my Palm Zire 71, my Canon Lide 30 scanner, a plethora of software unsupported on Vista. So far everything has been either directly on the iMac or supported via VMFusion and XP on the iMac. Truly an awesome experience.

PSE5 Scanner-Problem (Canon Lide 60)

Hallo, seit ein paar Tagen nutze ich PSE5. Ich bin wirklich begeistert von den Funktionen die PSE5 einem bietet. Speziell vom Organizer bin ich ganz angetan. Zur Zeit befinde ich mich noch auf Entdeckungstour durch PSE5.
Bislang nutzte ich PSE2(die Version lag damals meinem Computer bei).
Aber nun zu meinem Problem:
Wenn ich in PSE5 etwas scanne (Canon Lide 60)beginnt mein Bildschirm wie wild an zu flackern, und der ganze Scann-Vorgang verlangsamt sich enorm. Erst heute morgen habe ich einen Scanntest mit PSE2 gemacht und dort gib es keine Probleme.
Weiß jemand eine Lösung für dieses Problem?
Ich hoffe mir kann jemand helfen.
Harry

I have always used VueScan. Canon wants you to buy the LiDE 90 probably. Vista x64 drivers for my LiDE 70 (which I bought assuming it was current and that they would upgrade drivers) even requires modifying the Twain name for VueScan to work. And the developer (Hamrick) is very good at keeping his software updated. Canon uses its own proprietary protocols. So I don't even think it is industry standard enough for Apple to support "natively."
Vista. Yes, Canon brought out a driver for the LiDE in fall '06. SP1 is being held from full release and DVD mastering while some vendors have more time to add driver support for new hardware and systems, logicboards. Vista SP1 has been in beta since August, a public RC1 came out and two non-public updates, giving developers time to work with the new release.
But vendors aren't happy. Drivers don't make money, cost time to develop and test (it can take 1-4 months for a driver and firmware), so they don't get much thanks. Thankfully, a scanner like the LiDE series are under $100 and perform well.
I had a nice $400 laser printer for doing envelopes and a few letters, Lexmark doesn't have drivers, and neither does Vista, and my 'new' laser doesn't do envelopes as easy, but at least it was only $180 and can print 3x faster (but I waste a lot of envelopes to get one good one).
The cost of any new OS is to make older hardware and software obsolete. New software to require ever more powerful hardware. This was something IBM learned 40 yrs ago. All in the name of progress and commerce.
A new scanner vs VueScan Pro (lifetime support). And your VueScan license works with Vista and OS X.

Canon Lide 35 No Longer works in Snow Leopard

Here some more specific results on what happens when you try to scan with the Lide 35 in Snow Leopard.
1) The ONLY choice is to use image capture. Canon software doesn't work
2) Detect Multiple images is completely broken
3) The image size is super small. )i e, the dimensions settings don't work right
4) You have to increase the resolution to 600 to 1200 in order to "fool" Image Capture into scanning at the proper size
5) As soon as you select Ovweview a second time, it stops working and gives you a blank scan. You have to log out and back in to get it working.
6) The only "workaround" I've found is to scan the same dimensions every time at 1200 dpi and edit and save the photo in another app.
I realize the Canon Lide 35 is an older scanner, but please Apple, none of us want to buy a new scanner just because we upgraded to Snow Leopard.
I've spend an hour on the phone with Canon who tried to be very helpful. This happens on all my Snow Leopard Macs (I have three) and it seems clear that this is an Apple issue.

Hi Tee,
I can confirm what you are saying. I am running MacOS 10.6.2 on MacBook Pro and when I was trying to use my Canon LiDE 35 after installing "lide35osx7721en.dmg" and also "cstbosx5013ej4.dmg" I am still getting the error message "driver not found". The same Canon LiDE 35 still works beautifully with my PowerPC G4 under 10.4.11. - I am not sure whether there is any other software? The only oddity when installing those files I noticed was that "CNQL1208_ClassicNotSeize.kext" would not load...
I have no solution to offer at this stage other than using the old Apple... Anybody any ideas??

Canon Lide 80 - not working after 10.5.8 update

Hi,
Wondered if anyone has a workaround for getting a Canon Lide 80 scanner to scan using Photoshop Elements 6, it worked in OS X v10.5.7 previously as I copied the latest ScanGear CS 7.2X plugin into the Photoshop Elements plug-in folder then ran Elements through Rosetta and it scanned with no problems however this now does not work.
The plug-in is still selectable when using PSE6 but I get the following message "The necessary file could be missing or damaged, or the settings are incorrect. Reinstall the scanner driver. Scanner driver will be closed"
I have made sure I have the latest plug-in but to no avail. Any assistance would be greatly appreciated.
Cheers
Andrew

Can't speak specifically to Photoshop Elements, but my LiDE 80 works fine on 10.5.8 using both Canon's CanoScan application as well as VueScan, both of which use the same plug-in architecture as Photoshop.
This is on a MacBook (Santa Rosa) after updating to Leopard 10.5.8 (it was previously running 10.5.4, where the scanner also worked).
I am using the latest ScanGear driver and CanoScan Toolbox installs from Canon's US support website, where the
filenames are LiDE80_7252MXEN.dmg and CSTb4130MXE.dmg respectively (the Canon site shows an update date of July '09, but in actuality none of the files have been updated since 2005).
I didn't do anything special -- the scanner continued working normally after the system update.
What I'd try is remove the driver (just to be safe, download & use Canon's driver removal utility from the same download page), search & nuke any files called Scangear on the machine (I'd also remove CanoScan if you have it installed), then reinstall from scratch.

Acrobat 9 Standard won't recognize Canon Lide 200 Scanner

My recently installed Acrobat 9 Standard won't recognize my Canon Lide 200 scanner even though Adobe Photoshop CS2 does. I don't know what the problem is and how to solve it.

Adobe Acrobat Pro 9 was recently installed on new Vista 64bit computer and functions with all programs and even prints to my Dell 1600n printer, but when I try to scan from the printer, it causes this error message and shuts Acrobat down:
"ADOBE ACROBAT HAS STOPED WORKING A Problem has caused the program to stop working correctly. Windows will close the program and notify you if a solution is available."
I have lived with this since I bought the computer a month ago. Still no solution from Adobe and no response to an email that I sent to adobe support.

I have a problem connecting a canon Pro-100 injet printer to my iMac oS Mavericks.

I have purchased a Canon Pro-100 inkjet printer which I am trying to connect to my printer. The software on the disc was not compatible with OS Mavericks so Canon sent me the updated software. Still won't work. I get an air message which I have sent to Canon. They say it is an Apple problem which has occurred a lot recently. Aplle online chat support could not help. Has anyone else had this problem. I've got an expensive printer I can't use.

I know I have to give up on the printer and scanner- but I am going to try to find something to keep my tablet going for awhile.
Are you actually reading the responses that people are giving you?
1. Your printer will work with Gutenprint support, possibly will work with 10.9 drivers.
2. Epson has a scanner Yosemite driver for your scanner.
3. And Wacom has a driver for your tablet.
You have no reason to be that miserable, all things considered.

Can't control Canon Elura 100 DV Cam in PPro CS4

Hi,
I am comparing Final Cut Express vs. Premiere Pro CS4 trial, and I cannot get Premiere to control and import from my DV Cam, which is a Canon Elura 100. Has anybody been able to use this camera? My system is a MacBook Pro, running Snow Leopard.
Thanks!

If the camera does not have firewire out, you are out of luck.
Firewire is required to capture.

Problem workflow mxf canon xf 100

Hi,
I have shot a documentary with a canon xf 100. I could import the different mxf clips with the browser in Ppro CS5.5.2 but I cannot find a solution to work properly. I need to merge all the different mxf clips from each canon CONTENTS folder into one big clip, like if I had one big clip for each tape/card. For that, I created a new sequence from the different mxf clips and then I nested this sequence to get one unique file that looks like a unique clip. OK, but then, when I try to work from that nested sequence and to use it on my timeline, I cannot work with two mono tracks any more (I have set my project as mono, beacause I used two mono microphones). Everything I import from a nested sequence to the timeline becomes one stereo file.
Then I tried something else. Inside Ppro, I merged ("merge clips") my nested sequence with another sound track, wich is in fact the full sound track I exported in a wav format from
the same nested sequence. At first, everything seems to be OK : I can work on my timeline with that merged clip, and I get two mono files. ...BUT as soon as I close and reopen Premiere cs5.5, one of my two mono files becomes empty. I can see the two mono audio file on the timeline but one of them has no sound at all!
Any idea ? thanks.

Thank you Stephen, but I personally prefer to edit with one big file per card (or per tape) I can scrub easily, instead of having hundreds of small files with numbers (like mxf files), especially when I have hundreds of hours of footage. To help me, I can always make a detailed shot list.
So I tried to do like this ; sorry for my English and if I repeat certain points, but I hope it could help other people :
on the timeline, I imported all the mxf clips coming from one card,
then I calculated a new wav stereo file from all the files,
then I made a nested sequence with all the mxf clips, but without the original sound tracks (only video, not audio),
then I merged that nested video sequence with the new wav stereo file I have calculated ("merge clips"),
then I could import that new merged clip in the source monitor and edit on the timeline with two mono tracks.
But I met two new problems for a good editing:
First of all, as I already described, after I closed and reopened premiere pro, one of my two mono tracks on the timeline became empty: you can see the segments on the timeline but there is no more sounds inside. It is clearly a bug of ppro. I’ve read different posts with audio problems on mxf files imported into ppro.
So what I did is that instead of calculating a new stereo wav file from my original sequence, I calculated two mono files, one for each channel. Then I imported those files into ppro and and I merged it with my video only nested sequence. I, then, could edit properly with two mono tracks even if I closed and reopened ppro.
But the problem is that now, if, for any reason, I become out of sync on the timeline between video and audio segments, there is no more red indications to tell me the number of frames out of sync. And of course, you cannot use the functions of ppro to re-synchronize ("move into sync, slip into sync"). And this is a huge problem (strangely, a nested sequence keeps that function but it has only one audio track).
I sometimes wonder how the programs are developed. Mxf files is supposed to be a step ahead, but it becomes in the real editing, at least with ppro, two steps backward. From what I’ve read on the net, many people like me lost a lot of time trying to find a solution for editing mxf with ppro, and even if I decide to work with two mono tracks as I described, which is long and painful with hundreds of hours, how can I be sure I won’t meet another audio issue later on.
It is clear that the developers of ppro are not editors or directors. All I want to do with my mxf files is the basic of the editing. I want a car I can drive properly, not a car with air conditioned, that has no brakes.
So if they hear me : could you please update ppro so that we could edit properly with mxf files? It means :
1/ inside ppro, merge all the clips from the same card into one clip, that we can edit with two mono tracks if we decide
2/ keep the out of sync function for each audio channel with that merged clip.
Of course, if there is a workaround, I would be happy to know it.
Thanks.

TWAIN Sane with Canon LiDE 50

Hello!
I'm trying to use a Canon LiDE 50 scanner under OS X Mavericks 10.9 with TWAIN Sane drivers.
It worked well with Mountain Lion OS X 10.8 and now with the newly complied Sane drivers for Mavericks, Sane doesn't recognize the scanner anymore :-(
Anyone else experiences the same problem and has solved it?

Hi, same here. I was really happy to find Sane for OS X. But actually it does not work with my Canon Lide 50 and Mavericks. Before I have used the original Canon Lide 35 drivers to work with every OS X until Mavericks… But now I found a solution, just download the VueScan for the Lide 35 (which is the same Genesys hardware as the Lide 50) and it will all work. Also VueScan will work with the Scanner in Mavericks properly

Twain Drivers Are Not Recognizing my LiDE 100 Scanner in Photoshop CS5?

This is my first post, mainly becuase I'm stumped on every front to this problem, just bought myself a new 17" Macbook Pro the other day and immediately started to update all my drivers, through on Photoshop CS5 among a few other CS5 programs, but this is where things got hairy...
Since this is a 64 bit intel mac (Snow Leapord) , I went over and decided to download the TWAIN plugin, dropped it in the Import/Export plugins folder, went to the Adobe Photoshop app folder and happily clicked boot as 32 bit... aaaaand... NOTHING. It didn't see my scanner, and my scanner is a Canoscan LiDE 100, not that old. I've already had success doing this with Win 64 bit as long as I opened a 32 bit version of Photoshop, but no luck so far on the Mac. The scanner works fine with Image Capture so I know that he scanner is alive.
I've tried rebooting, finding other TWAIN plugins, even out of curiosity I've toggled between 32 and 64 bit Photoshop to see if the Scanner could be recognized. I know I could scan using Image capture, but I'd rather get this problem sorted out. I know that in some cases people boot using Rosetta, but this scanner isn't that old so I don't think that would be the problem.
If anyone has any advice, it would be greatly appreciated, and I realize that sometimes the most simple answer is the one that's the most easily overlooked, and I'm hoping that's the case.
Thanks everyone!

Scanning with TWAIN has become increasingly buggy.
Why not just use the Epson scanner software that came with the scanner?
That way you can continue to use Photoshop while using Epson to scan.
There are more features available from Epson than with Image Capture.
However, if you feel the need to use TWAIN, here is the link for Mac CS5 plugin.
Five seconds with Google would get you this:
http://www.adobe.com/support/downloads/detail.jsp?ftpID=4904

Canon S-100 forgets date and time each time it's turned off.

Hello, I have a canon S-100 that forgets the date and time each time it's turned off. I see chat rooms that talk about if the internal battery is shot. The S-100 will loose date/time if the battery is removed. My S-100 asks for date/time every time I turn it on without touching the battery. Has anyone come across this issue?

The S100 has a built in rechargable battery that runs out after a few weeks of non use and no battery inserted. You can also set it to automatically update via GPS as shown on page 115. I attached a portion of page 21 from the user manual to explain it better.

Has 10.8.3 broken Canon Lide 100 driver?

Similar Messages

Maybe you are looking for