Has anybody integrated with CO-Sign for SSO / Authentication

Hi Folks,
Has anybody looked at Co-Sign for SSO in terms of forms / discoverer in the 11g release?
Gary

Marvin,
You make me feel better. I thought I might have been the only one who had ever done this. ;-) It's not too bad to clean up.
I am referencing old notes, and do not currently have access to an OID instance to verify, but try this:
In Entry Management, look under the default Oracle Context, under Services, and Ebusiness. You should see an entry for your EBS instance. (For example, the full DN might be: cn=VIS,cn=EBusiness,cn=Services,cn=OracleContext). Remove this record, and you should be set. You may need to remove other links to this record under your custom context. For example, there may also be a DN cn=VIS,cn=EBusiness,cn=Services,cn=OracleContext,dc=your_org,dc=com.
I was initially concerned that there might be a ton of junk to remove from OID related to the EBS instance registration, but I was not able to find any other likely entries, and was able to proceed with re-registration without issues after removing these two entries.
Hope this helps!
Regards,
John P.
http://only4left.jpiwowar.com

Similar Messages

I have been a loyal customer for years and have a hot spot because internet options are very limited in our rural area. I have stayed with 10G since the beginning. Most months I don't use the 10G. Verizon has no problem with me paying for Data I don't

I have been a loyal customer for years and have a hot spot because internet options are very limited in our rural area. I have stayed with 10G since the beginning. Most months I don't use the 10G. Verizon has no problem with me paying for Data I don't use. This month my daughter comes home from College and she accidentally uses 24G.....14 over get blind sided with $140.00 in overages. I called Verizon today......stopped in to the store today......My neighbor told me they waved charges for her one time. Lots of charges.....But I'm am getting no help. Not even an offer of a payment plan to help me out. I went back just 6 months and I have over paid for 19G.....Seems like they would like to help out their loyal customers!!!! Does anybody have any suggestions on how to deal with them? We are not wealthy....or I would just pay this and walk away......

There is a big misconception in what customers believe a cell carrier is obligated to do.
You pay a set price to use up to that amount of xx data. It makes no difference if you use it to the paid limit or way under. Its like peace of mind when you don't have to worry about a data counter.
Your daughter used the data, your plan is quite clear of what overage charges are. Why should or would Verizon wireless just forgive the charges because you are a customer? Your daughter used the data, get the money from her. That is the responsible thing to do.
There is no "I have been a loyal customer so please remove the $120, or $250, or $2,000.00 since I did not mean to use it"
Your electric company, or gas company or any other company does not remove valid charges. Why should Verizon wireless?
Just pay the invoice and don't think you are being mistreated because Verizon is a business and not a charity.
Good Luck

My google map that was on my website now has been replaced with a sign that says (mobileme is colsed). I have tried to delete this and reinstall google maps, but the same thing appears. Can anyone help?

My google map that was on my website now has been replaced with a sign that says (mobileme is colsed). I have tried to delete this and reinstall google maps, but the same thing appears. Can anyone help?

See this page for info about Google maps...
http://www.iwebformusicians.com/iweb-snippets/map-tutorial.html
... how to get the code and paste it into an HTML Snippet.

Has anybody got a labview driver for Lecroy 9410 ?

Has anybody got a labview driver for Lecroy 9410 ?

Unfortunately I was unable to find a driver for this instrument either. This leaves you with one of a couple options. First, I would like you to submit a request for this driver at:
http://zone.ni.com/idnet/other.htm
We develop drivers based on demand and popularity so the more requests we have for it, the greater the possibility that we will develop one.
If you would like to try developing your own instrument driver (or modify the existing one), we have documentation, model instrument drivers, and driver templates to help at :
http://zone.ni.com/idnet/development.htm
We also have a syndicate of third party vendors that specialize in National Instruments' products and services. Some of the vendors specialize in driver development. I would sugges
t contacting one of the Alliance members at:
http://www.ni.com/alliance
If you have any further queries, please let me know

I have a Maxtor 3200 which has stopped communicating with my iMac for no reason can you help i'am running the latest system

I have a Maxtor 3200 which has stopped communicating with my iMac for no reason can you help i'am running the latest system

I have never seen this before. Try using these installers
Flash Player for ActiveX (Internet Explorer)
Flash Player Plug-in (All other browsers)

HT5648 OS10.6.8 Firefox 24.0 The new Yahoo mail shows no graphics. However, the new Yahoo mail displays correctly in Safari and Chrome. I believe this has to to with the settings for Javascript. Help me, please.

OS10.6.8, Firefox 24.0
The new Yahoo mail shows no graphics using Firefox 24.0 - just identical rectangles where new icons should be.\. However, the new Yahoo mail displays correctly in Safari and Chrome. I believe this has to to with the settings for Javascript. Those settings aren.t easy to access in the most recent Firefox 24.0 version. Help me, please.

The settings for Javascript are either on or off, Fireefox 24 doesn't give you a option to turn off Javascript, unless you installed something like NoScript extension (or some other Javascipt blocking add-on)
If NoScript, then you need to use the View > Toolbars > Customize and drag the NoScript "Temp Allow All" button to the toolbar area to enable all enabled scripts (including Javascript) on that web page.
Under the Firefox Help menu is a option to restart with add-ons disabled to see if something you might have installed is causing your problem.
Reinstall Firefox or create another user account and run Firefox there to try to localize your issue.
I'm having no problem here on 10.6.8 in Firefox, Chrome or Safari, Yahoo Mail works perfectly.

Integrate SAP Netweaver 7 with SharePoint 2013 for SSO

We are planning to Integrate SAP Netweaver 7.0 with SharePoint 2013 for SSO using SAML 2.0
Would like to know what 3rd Party IDM tools are supported by SharePoint 2013 apart from ADFS
Regards
Mirza
FBM

This should help you Faheem
http://scn.sap.com/community/interoperability-microsoft/blog/2011/01/31/installing-duet-enterprise-the-sap-side--a-video-guide
Please remember to click 'Mark as Answer' on the answer if it helps you

Has anyone integrated with PaymentTech for credit-card processing?

My client would like to capture credit-card payments using PaymentTech payment processor. We are using Oracles Apps 11i. I am aware that AR is integrated with iPayment for credit-card processing. However iPayment uses Cybercash as the payment system and it does not currently support voiceauth (i.e. ability to capture/settle payments based on an authorization not obtained via iPayment).
Has any one done any custom development to integrate directly to PaymentTech (or to a
3rd party application which integrates with PaymentTech)? I would appreciate if you can provide any directions.
Thanks.
- Tushar Khinvasara
Oracle Consulting, iServices Southwest
P.S.: If possible, please also cc your response to my internet email addr [email protected] which i can more easily access from the client site.

Authorize.net is a supported payment gateway, take a look here - Supported payment gateway providers and here - Authorize.net for the steps to configure it.
Thanks,
Mihai

Has anybody integrated Shoretel conferencing with Adobe Connect?

Has anyone integrated ShoreTel audio conferencing with Adobe Connect? If so, I would love some tips on how to do it.

James, I'm interested in this topic as well! I am not an IT person, just a user. I have Tech Support who are dealing with this. We have integrated our Shortel system 99.9% with Connect, but for some reason we can't get the DTMF to send properly. Very frustrating! Adobe has provided some assistance. Adobe wanted the SIP information (SIP IP adddress, username and password) which we set up; but my IT folks needed the correct ports that Connect wanted. This is what they sent me:
Below are the ports you
need to open to make FMG talk to your SIP server:
2222 - HTTP
8506 - RTMP
Flash Media Gateway to Internet   SRC-IP=<Server-IP>,
SRC-PORT=5060, DST-IP=ANY, DST-PORT=5060
Internet to Flash Media Gateway   SRC-IP=ANY, SRC-PORT=5060, DST-IP=<(>
<<)>Server-IP>, DST-PORT=5060
Flash Media Gateway to Internet   SRC-IP=<Server-IP>,
SRC-PORT=5000_TO_6000, DST-IP=ANY, DST-PORT=ANY_HIGH_END
Internet to Flash Media Gateway   SRC-IP=ANY, SRC-PORT=ANY_HIGH_END,
DST-IP=<Server-IP>, DST-PORT=5000_TO_6000
Maybe this will help?
Penny

LMS 3.2.1 integration with Clarity NMS for snmp trap forwarding

Our client have integrated Clarity NMS to Ciscoworks LMS 3.2.1. So far they are receiving raw alarms/snmp traps but it lacks information/inventory of the originating device. Kindly see sample raw alarms below:
2420: 2011-11-25 12:10:46 Received trap ==> Received SNMPv1 Trap
Community=ciscoworks
Enterprise=1.3.6.1.6.3.1.1.5
Generip trap type=2
Specific Trap Type=0
Trap From=10.220.10.1
Trap ID=1.3.6.1.6.3.1.1.5.2
Trap Time=-1436283373
1.3.6.1.2.1.2.2.1.1.83=83
1.3.6.1.2.1.2.2.1.2.83=GigabitEthernet1/40
1.3.6.1.2.1.2.2.1.3.83=6
1.3.6.1.4.1.9.2.2.1.1.20.83=Lost Carrier
EndTrap
10933: 2011-11-24 11:57:53 Received trap ==> Received SNMPv1 Trap
Community=ciscoworks
Enterprise=1.3.6.1.4.1.9.1.291
Generip trap type=2
Specific Trap Type=0
Trap From=10.220.10.1
Trap ID=1.3.6.1.4.1.9.1.291.2
Trap Time=1628056965
1.3.6.1.2.1.2.2.1.1.8=8
1.3.6.1.2.1.2.2.1.2.8=E1 0/0/0
1.3.6.1.2.1.2.2.1.3.8=18
EndTrap
As you can see, those raw alarms doesn’t contain any information about the originating equipment or the physical card, port related information where those alarms were generated. Instead those alarms received are just NMS level alarms.
How do we resolve this so that the inventory of the equipment would be part of the trap to be received by Clarity from Ciscoworks.

Hi,
Is the issue you have the source IP address of the forwarded trap? Per RFC it is the IP of the actual device sending the trap. The originating IP should be contained within the packet. I have included some additional information you may find helpful.
Q. What is the difference between SNMP Raw Trap Forwarding and SNMP Trap alert/event Trap Forwarding? Does DFM support both?
A. You can configure raw trap forwarding at DFM > Other configuration > SNMP Trap forwarding, and processed event/alert trap forwarding at DFM > Notification Services > SNMP Trap Forwarding. Processed trap is "when DFM receives certain SNMP traps, it analyzes the data found in fields (Enterprise/Generic trap identifier/Specific Trap identifier/variable−bindings) of each SNMP trap message, and changes the property value of the object property (if required)". Raw trap is the trap that the device forwards to DFM and DFM has yet to process it. For more information, refer to the DFM User Guide. Yes, DFM supports both ways of trap forwarding.
http://www.cisco.com/en/US/products/sw/cscowork/ps2421/products_qanda_item09186a0080a9b35b.shtml
DFM will only forward SNMP traps from devices in the DFM inventory. It will not change the trap format—it will forward the raw trap in the format in which the trap was received from the device. However, you must enable SNMP on your devices and you must do one of the following:
Configure SNMP to send traps directly to DFM
Integrate SNMP trap receiving with an NMS or a trap daemon
The versions of SNMP traps supported by DFM are described in SNMP and ICMP Polling. For information on forwarding processed and pass-through traps, see Processed and Pass-Through Traps, and Unidentified Traps and Events.
Pass-through traps are traps that DFM receives from devices that are not in the DFM inventory, and DFM has not processed. Forwarding these traps is controlled using Configuration > Other Configurations > SNMP Trap Forwarding. These traps are shown in the Alerts and Activities display because of their relevance to fault monitoring. Pass-through traps are displayed as follows:
As one of the following events:
> InformAlarm
> MinorAlarm
> MajorAlarm
With the device type and the device name from which it was generated.
If DFM does not know which device generated the trap, it ignores the trap. Pass-through traps will be cleared after a default interval of 10 minutes to one hour
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_device_fault_manager/3.2/user/guide/dfm32ug_Book.html

Undestanding the OSM-AIA integration with SAF agent for RODOD 11gr2.

Hello all,
As we don't yet manage the sending of sales orders from AIA 11.1 to OSM 7.2, I looking for some information about the way AIA and OSM may be integrated with SAF agents.
During the installation of the O2A cartridges in Design Studio, the SAF agent has been choosed against the JMS bridge approach.
So in OSM's WebLogic domain,
- a SAF agent is created
- JMS resources are created in the oms module:
-      a Remote SAF Context describing the way to be connected to the AIA's weblogic instance
- the remote imported destintations i.e.:
AIA_CRTBO_OUT_JMSQ
     AIA_CRTCUST_OUT_JMSQ
     AIA_CRTFO_OUT_JMSQ
     AIA_CRTTTREQ_JMSQ
     AIA_FOPROV_OUT_JMSQ
     AIA_LFERROR_JMSQ
     AIA_UPDSO_OUT_JMSQ
     AIA_UPDTTREQ_JMSQ
Sending an order from Siebel to AIA fills an AIA_FOPROV_IN_JMSQ on the AIA database which seems to be not consumed because on the OSM side, no order is ssen in the oms_ws_requests queue.
So, we are wondering if the Order to cash PIP in AIA is incomplete or not. Should be a SAF-agent in AIA to send orders to OSM? Should we complete the current SAF-Agent in OSM to receive and send messages to AIA?
To integrate ASAP or UIM to OSM, it is recommended to define a SAF-Agent in OSM to send messages and a SAF-Agent in ASAP/UIM to reply to OSM. It lets me think that our AIA installation is incomplete.
On the other side, when JMS bridges are used in OSM in 7.0.2, a bridge called created AIA_2_CFS_CreateOrder_is defined to locate and consume the remote JMS queue AIA_CRTFO_IN.
In conclusion, we'd like some explanations on the way to integrate as well as possible AIA and OSM in a SAF context. It will help use quite a lot.
Many thinks in advances.
Regards,
Christophe.

Hi
On OSM side should exist SAF agent for sending messages to AIA queue's and same on AIA side for sending to OSM queue's. You can even combine SAF agaent on one direction and bridge's in another direction but you'll have to do it manually in that case.
If you see message in AIA queue and not forwarding to OSM I would first check SAF agent on AIA side ( usr/pass + remote destination (OSM) )
best regards
Tomac

Has anybody experience with "Cisco Anomaly Guard Module"

Hello,
had anybody experience with "Cisco Anomaly Guard Module" WS-SVC-AGM-1-K9 for Catalyst 6500?
We're looking for some IDS/IPS prevention system which could take 2-3 Gbits of traffic. From the documentation it looks not bad, and we can get them as used parts (6500 + Sup720 + AGM +ADM) quite cheap. The second solution is Arbor with cisco12000 as boader router (10Gbit uplink) is much more expencevie.
Arbor tries of cause sell us their solution as "Cisco Anomaly Guard Module" is ot of sale and doesn't have any new features, but from the Data sheets Cisco AGM is eactly what we need.
Or may be is there another solution which could be comparable to those two?
Thank you.

Hello padatta,
AGM/ADM are IDS/IPS systems, one can of couse discuss about the terms, but it won't be productive :).
IDSM2 has not enough performance and it should sit inline, ADM/AGM can change he next hop for the diverted traffic and be out of traffic path during the normal operation.
Konstantin

IRecuritment: Resume Parsing with Single Sign on (SSO)

Application Version:11.5.9
RDBMS Version:9.2.0.7
Patch Level:IRC.D, HR_PF.G
Problem Description/Question:
Anyone successfully parsed resumes with Single Sign On enabled. We are unable to parse resume with SSO. If I disable the SSO the parsing is working fine. With the SSO enabled resume parsing giving the following error:
javax.net.ssl.SSLException: SSL handshake failed: X509CertChainIncompleteErr
Pl. let me know if you have any suggestions/work around to resolve the issue. Client is going to live in 3 weeks. Any help is appreciated.
Thanks,
V

Hi Rainer,
you can find this setting in your Internet Explorer. Use Tools -> Internet Options -> Advanced. In the section "Security", check "Enable Integrated Windows Authentication (requires restart)" and restart your browser.
If the error still persists Note
934138 might be useful.
Hope this will help out.
Regards,
André

Flash video has not worked with Firefox browser for years. When will you fix this?

Anyone who uses Firefox browser (for Windows or for Mac) knows that flash video playback ceased working sometime around Firefox ver 13 and has not worked since.
The Mozilla people say it is Adobe's fault - instead of fixing Firefox.
They say roll back to Adobe Flash version 10.
This solves the video problem, but then, any other services that depend on the latest Flash build, quit working properly.
This situation leaves millions of Firefox users in perpetual frustration. We can't use our browser of choice to view any web video built with Flash.
This is so unacceptable. I am unable to understand why Adobe and Firefox don't get together and iron out whatever code incompatibility is causing this.
I would really like to hear Adobe's explanation for this.

proteus-editorial wrote:
Anyone who uses Firefox browser (for Windows or for Mac) knows that flash video playback ceased working sometime around Firefox ver 13 and has not worked since.
The Mozilla people say it is Adobe's fault - instead of fixing Firefox.
They say roll back to Adobe Flash version 10.
This solves the video problem, but then, any other services that depend on the latest Flash build, quit working properly.
This situation leaves millions of Firefox users in perpetual frustration. We can't use our browser of choice to view any web video built with Flash.
This is so unacceptable. I am unable to understand why Adobe and Firefox don't get together and iron out whatever code incompatibility is causing this.
I would really like to hear Adobe's explanation for this.
Uh... I don't know what planet you posted this from, but Flash video has worked flawlessly with Firefox for hundreds of millions of users here on earth, without any gaps since Firefox was still called Mozilla.
For the record, I have Firefox 28 with Flash Player 13 installed on:
WIndows XP (SP3-64bit)
Windows Vista Ultimate (SP2-64bit)
Windows 7 Ultimate (SP1-64bit)
Windows 8 Enterprise (64bit-2 machines)
Windows 8.1 Enterprise (64 bit)
OS 0.6.8 Server
OS10.7.5
OS10.8.5
OS10.9.2
And I've had Firefox with Flash Player since 2003 on both OS formats. I've never had a compatibility problem.
I also use Chrome, IE, Opera, Safari and a few other browsers you probably never heard of (like SeaMonkey, Maxthon, Waterfox, iCab, OmniWeb)... Flash works in all of them.
I'd have to say the problem is with your system specifically, because if it was a Firefox/Flash compatibility problem, there would have been hundreds of millions of complaints about it, for over a decade. That... just isn't the case.

CTI Integration with SAP Cloud for Customer

HI,
Can some one help me how to connect cti with sap cloud for customer.

Hey Achyut,
Cloud for Customer supports CTI and their is an official document for the same as well.
https://websmp204.sap-ag.de/~form/sapnet?_SHORTKEY=01200252310000101184&_SCENARIO=01100035870000000202&_OBJECT=011000358…
You can find related docs on service.sap.com/cloud4customer
Thanks,
Ravi

Has anybody integrated with CO-Sign for SSO / Authentication

Similar Messages

Maybe you are looking for