Has anyone else's Airport base station died?

My base station just went down...They are currently on back order everywhere...For some reason I cant get my airport express to connect at home, I have full bars, but it wont connect to the internet....any advice?
(Ive used the express many times before while traveling, with no problems at all)
thanks in advance.

You didn't stipulate DSL or Cable, but try the following:
AirPort Express Base Station Setup (AX) w/High-Speed Cable Modem
Modem/Router Power ReCycling
- Power-off the Cable modem, AX, & computer(s). (If possible, leave the modem off overnight.)
- Power-on the Cable modem; Wait at least 30 minutes.
- Power-on the AX; Wait at least 5 minutes.
- Power-on the computer(s)
Perform a "hard" reset of the AX
- (ref: http://docs.info.apple.com/article.html?artnum=108044)
Setup the AX
With the network components powered down, set up the AX, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
AirPort tab
- Base Station Name: <whatever you wish or use the default>
- AirPort Network Name: <whatever you wish or use the default>
- Create a closed network (unchecked)
- Wireless Security: Not enabled
- Channel: Automatic
- Mode: 802.11b/g Compatible
Internet tab
- Connect Using: Ethernet
- Configure: Using DHCP
- WAN Ethernet Port: Automatic
Network tab
- Distribute IP addresses (checked)
- Share a single IP address (using DHCP & NAT) (enabled)

Similar Messages

I deleted Bonjour, since I don't need it for remote printing. Now I get the message " Airport Base Station has stopped working: and also a message saying APAgent.exe can't be found. What to do??? Thanks.

I deleted Bonjour since I don't need it for remote printing. Now on start-up I get the message: "Airport Base Station Agent has stopped working" and also message: "can't find APAgent.exe.: Do I need AP Agent?? What to do?? Thanks.

The APAgent monitors your AirPort base station and informs you if there are things like firmware updates available. This utility relies on Bonjour, but is not required for base station operation. However, Bonjour makes it easier for your PC to "find" the base station via the AirPort Utility and I would recommend that you keep it installed. If you don't want the APAgent, you can just use the Apple Updater utility (that was also installed when the AirPort Utility was installed) to remove it.

Airport Base Station update has disconnected my internet

i recently updated my airport, during the installation i pressed change all to key chains, it said my internet might be temporarily unavailable however it never came back. I can no longer connect to the airport base station, or connect to my original network, whenever i try to access files to do with my network it says there is an error. i've gone through system preferences to try and reconnect but it wont allow it, i have also gone through airport utility but it just tells me to rescan.
thankyou for your help

If all else fails, you might need to perform a soft or hard reset to factory defaults, then you have to set everything up again, but it might restore it to working condition.
Not sure if this is the model base station that you have:
http://docs.info.apple.com/article.html?artnum=107451
check the user guide that came with it, in case the procedure may be different.
I hope that helps.
When I bought an "open-box" unit, the device was already set up by someone else with a password, and the hard reset allowed me to start from scratch so I could configure it.

Since updating to Yosemite my airport express (used for airplay) connects for a short period then drops, the error message "An error occurred while connecting to the AirPlay device "Kitchen". The host cannot be reached." Has anyone else had this?

Since updating to Yosemite my airport express (used for airplay) connects for a short period then drops, the error message "An error occurred while connecting to the AirPlay device “Kitchen”. The host cannot be reached." Has anyone else had this problem

I'm having the same issue. Haven't found a workaround. I use a main TimeCapsule as my main router, also have another TimeCapsule that extends the network, three Airport Express and an AppleTV. For whatever reason, the two AirportExpress that I have in a different rooms cut out. I only have 600 square foot apartment so it's not that big, the signal should be strong enough. Airport Utilitiy reports the signal strength to be strong on all devices.
I'm using all new equipment, a new MacPro for my music, new TimeCapsules, new Airport Express, new everything with the latest Yosemite software. Very frustrating. My Airplay used to work very nice and now I'm constantly having issues and restarting my network. I did a fresh install of all my software on my MacPro when I got it in January so it's not as if it's an old machine with old software, everything is new within the last 6 months.
The only workaround I found so far is to unplug the devices and to plug them back in. Since upgrading to Yosemite, I'm restarting my Airport Express at least twice a week. Very annoying.

AirPort Base Station Update 2007-001 for Windows

Hi,
Is anyone else having problems after applying the latest AirPort Base Station update (version 5.1) found here
http://www.apple.com/support/downloads/airportbasestationupdate2007001forwindows .html
Before this update I was able to use the AirPort Utility in Windows (version 5.0) but now I receive the following error
AirPort Utility has encountered a problem and needs to close. We are sorry for the inconvenience.
AppName: aputil.exe
AppVer:5.1.0.14
ModName: kernel32.dll
ModVer: 5.1.2600.2945
Offset: 00012a5b
The only fix I have is to uninstall and reinstall the original version 5.0
Any help will be much appreciated.
Thanks
Dell Inspiron Windows XP Pro also MacBook with Mac OS X (10.4.9)

You are not alone, I have the same problem. This is after removing and reinstalling 5.0, re-downloading the update - once from Software Update and once directly from the apple site. Still NO JOY! Back on 5.0

Airport base station and Fios

I just got FiOS put in at my house. I used to have a cable modem and my airport base station worked fine with my G4 ibook. Well, I just got the fios installed and I hooked up my airport to it and I can't get it to work. The verizon provided modem/wireless router will work for my G4 ibook for a wireless signal. I was planning on getting a airport express for air tunes but if the extreme base station won't work I'm wondering if the express will work. Has anyone else had this problem? I'm not the saviest with computers and I'm fairly new to Mac but committed to Mac now. Any help would be appreciated.
G5 - G4 Mac OS X (10.4.9)

Will the AX setup by easy to do with the airport utillity setup?
Yes, just follow the directions in KB 302153, AirPort Express: How to join an existing wireless network in client mode.

Airport base station unconfigurable.

I have an airport base station from 2003 with my 17" macbook pro of 2003.
The video chip is dying so my laptop is unusable.
My wife got an iMac in 2008 and we have OSX 10.5.8 installed.
This internet connection right now is over the airport wireless.
We have upgraded to Airport Utility 5.5.1 which of course now does not see the
base station. I now cannot reconfigure anything on the base station.
As we upgraded the OS, we had to 'upgrade' to Airport Utility from Airport
Admin.
The serial number of my base station (PW14209PH93) is not even found in Apple's
records!
I am trying to connect my new hpg72 laptop to the network. It sees the network
but won't connect. The iMac sees the laptop in the DNS screen of System Prefs.
but won't connect. I'd like to connect to internet with new laptop.
Can anyone help? I am soooo frustrated.
Thanks

Jean Cawley wrote:
The original 15" and the airport were purchased in early 2003 and therefore probably 2002 models.
The base station is round, aluminum colored and has one phone jack connection, one
power in and one ethernet connection.
That's the original "graphite" AirPort base station. Since it only supports the very slow 802.11b protocol (which has a "raw speed" of 11 Mbps and a "maximum throughput" of 5.5 Mbps), you're doing yourself a disservice by trying to use it with newer clients.
I am baffled by this apparent built-in obsolescence.
How long do you think a company should support a device. Is 8 years not long enough?
The older Airport Admin Utility appears not to be available.
Not true:
http://support.apple.com/kb/DL85
However, it won't run under OS X 10.6.

Airport base station agent process without the device

Hello,
just noticed that in the startup items of my macbook account I have an item labeled "airport base station agent".
However, I dont have an airport base station...
Since I'm having regular troubles with my wireless, I'm just wondering if anyone can suggest an explaination why the item is there, whether it might be an issue for my macbook wireless and whether should I remove it from the startup items or not.
Thanks.
Paolo

I ended up manually removing the AirPortBaseStationAgent.plist file itself from /System/Library/LaunchAgents/ and the AirPort Base Station Agent Process has stopped running in Activity Monitor ever since. I don't know how good of an idea this was to do but it solved the problem. My AirPortBaseStationAgent.plist file had this info in it:
<plist version="1.0">
<dict>
<key>EnableTransactions</key>
<true/>
<key>KeepAlive</key>
<dict>
<key>PathState</key>
<dict>
<key>/Library/Preferences/com.apple.AirPortBaseStationAgent.launchd</key>
<true/>
</dict>
</dict>
<key>Label</key>
<string>com.apple.AirPortBaseStationAgent</string>
<key>ProgramArguments</key>
<array>
<string>/System/Library/CoreServices/AirPort Base Station Agent.app/Contents/MacOS/AirPort Base Station Agent</string>
<string>-launchd</string>
<string>-allowquit</string>
</array>
</dict>
</plist>
It is an older plist file dated Dec. of 2008 which got transferred to the my iMac via the Migration Assistant in Jan. of 2009. This file somehow didn't ever seem to update no matter how I configured the AirPort Utility. The file "com.apple.AirPortBaseStationAgent.launchd" that it makes reference to in /Library/Preferences/ doesn't exist on my iMac.
Thanks,
Gerard

Has anyone else experienced Airplay audio dropping?

Has anyone else experienced Airplay audio dropping while playing mp3s from MacBook Pro to Apple TV 2 and/or Airport Express g and/or n versions with an Airport Extreme N base? Using mp4 works fine but I've got some older files in mp3 that in between tracks the audio drops out on all external Airplay speakers while the track keeps playing on the computer.

I too have random drop outs on streaming from a Mac mini (2011) to an ATV. It seems to happen for internet radio and all sorts of mp3, mp4 files.
Yikes.

Airport Base Station Set Up

Hi, I've been trying to get an Airport Base Station set up for a few weeks. There is currently a problem getting wireless connectivity. The computer recognizes the base station, but does not see the server. I'm not sure how to get a wireless connection from the current location of this base station. The base station is inside of a classroom with reinforced steel walls and a steel door. I believe that this is causing a major issue with getting wireless connection. Is there anything that I can do to try and get connection? I tried hooking up an antenna, but that did not work. The only thing that I can think of is to get a few base stations and just hook them up going up the stairs to this classroom. I'm really pressing for the school to get an Ethernet connection so that we would not have to worry about wireless for this part of the building. This is the only part of the building that is really bad for reception. If there is anything else that I can try to get connection please let me know.

If you could run a length of proper antenna cable to a QuickerTek unit,
a "powered external antenna" could at least get the signal past the steel
and concrete signal barriers. Ethernet into the classrooms and then go
wireless is even better; and depending on class size and expected other
features (such as wireless printing, etc) the options vary in what wi-fi
base you use.
The AEBS seems a bit more durable and has a few more features than
an Express base station; plus the larger unit supports more connections.
But, without a source for a signal, you may be facing headaches.
What about one of those devices that uses electrical outlets for a data
or internet connection? There may be alot of interference in the wiring
in a school or commercial building; but there may be a chance you can
get some kind of device for the ethernet data to flow over AC power wire.
A few, in an older article about data over phone lines, include
adapters from a few companies in this link:
http://www.tidbits.com/tb-issues/TidBITS-482.html
The "Farallon HomeLINE network" was promising in some
cases; if there is something that can send DSL over house
hold or AC wires, then decode it, you may get internet into
a building that has no ethernet and can't get wireless.
Someone probably knows of a newer technology or a way
to work around your isolation issues in a steel/concrete bldg.
PS: Isn't there any technology grants with the phone or ISP
companies in your area from such places as the Gates Found
ation or other networking grants for schools that could have
the phone or internet providers do that wiring upgrade?

None of my airport base stations are picked up by my mac- what c

My macbook pro is running OS X Lion 10.7.5 with all updates up to date. I have itunes running 11.0.1. I have two airport base stations and three airport expresses and one of them has speakers comnnected to it. All the airport kit has a green light on it indicating it is connected to the wireless network but airshare does not pick up the speakers. When I open airport utility 6.1 it doesn't find any of the airport base stations or the airport expresses.
I am assuming that the airport kit needs to be updated with new software but without the mac detecting they are there I don't know how to do this.
Please can anyone help me.

OK, so it's a security issue. My guess is that WEP Transitional, which is available in the 802.11n (802.11b/g compatible) setting is not what the PCs want to see.
They need to probably work with either WEP 40 bit or WEP 128 bit ecryption.
These settings are not available in the 802.11n (802.11b/g compatible) mode, but they are available in the 802.11 b/g compatible mode. Hold down the option button while you are selecting the Radio Mode and you should see this setting.
For Security, also hold down the option key while you click on the drop down selection box and you will see more choices. Try 128 bit first to see if that will work. The older PC may need to use WEP 40 bit, so that may be the final setting that will work.
Unfortunately, you won't be able to connect with your MacPro at "n" speeds in these settings, but it will be the best available compromise.

Can't remember my password for my airport base station

I am trying to add another device to extend the wifi but I can not remember my password to my airport base station what do I do?

Reset it.. or find the old password.
Plug the computer into the airport by ethernet.. or you can do this by wireless..
Press in reset button for just 1sec.. (means less than 10sec)..
This is called a soft reset.. all passwords go back to default.. public for the base station.. nothing for wireless..
You now have full access for 5min.. open the airport utility.. click on the airport.. go to passwords.
Lo and behold.. all your secret identity available to all and sundry.
Note.. all security on the airport routers is illusionary.. as long as anyone has physical access to it.. they can find out everything.. and what is more.. there is no record once the 5min expires.
Sure is great for domestic equipment though... stops support calls dead.

Old airport base station quits working several times and week and won't let

me change the password.
I changed the password on my ibook and reset the airport base station but it still will not change the wpa2 password to the new one. I'm changing the password to rule out anyone having hacked into the network. Several times a week the whole network goes down and I have to turn off power to the base station to get it working again.
I have plugged it into a battery backup ups but that has not prevented it from crashing.

Pick, a quick Google search for "Airport Firmware 5.5.1" yielded the following link:
http://mac.sofotex.com/download-122643.html
I sense you're getting frustrated - I have a gift for such perceptiveness. Anyway, I wish I could explain your problems but I have no magic bullet for what you're experiencing. All I can offer is to suggest you download and install the above firmware. Hopefully the link works; I haven't tried it. There may be other ways of obtaining 5.5.1 but none was immediately apparent from Apple. Once installed, stick with firmware 5.5.1. As I noted I suffered major problems with 5.6 and have heard anecdotal reports of similar problems with 5.7 though apparently they're much rarer. My Extremes run literally forever without problems so I hope yours can too.
Next, disable all the encryption on your network for the duration of your troubleshooting. Simplify things as much as possible - remove all but one wireless client from your network. Perform a "hard reset" of your Extreme and reconfigure it from new. Run things like that for a while and see if anything changes.
Is it possible you're suffering from poor power quality e.g. dropouts, surges, sags, etc? Have you tried a UPS or at least a surge suppressor? I had a spell last summer when the utility would shut off power for a half second a day, literally, a half second, once a day, every day, for weeks. It drove me nuts. They immediately stopped this nonsense the moment I started running my Airport off a battery.

Has anyone else experienced web pages in Safari being unexpectedly re-directed to knock off MMO ad sites like 'League of Angels'?

As recently as one month ago, I started experiencing a phenomenon where web-pages I was on would randomly be redirected to ad sites for knock-off MMO's. For example, if I had left a tab open to an article on Cracked.com, but was reading a different tab, the Cracked article would re-direct itself to another website. This usually was a minor annoyance, in that I would just have to go back a page in my browser, but this evening I was watching an episode on HBO Go and in the middle of streaming the video the web page abruptly changed to League of Angels. Has anyone else experienced these strange re-directs, or know what is causing them?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports 'com.autodesk.AutoCad com.evenflow.dropbox com.google.GoogleDrive' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n\t(%s)\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1000) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/d;/(etc|Preferences)\//s/^\.\/[^/]+//p;' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| ","||kMDItem'${p[35]}'=");sub("^.."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[9]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ +B/{ s/.+= |(-[0-9]+)?\.s.+//g;p;} ' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / /{$0="'"${p[28]}"'"};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil PlistBuddy whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '-c Print /L*/P*/loginw*' '-c Print L*/P*/*loginit*' '-c Print L*/Saf*/*/E*.plist' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' '-c Print\ :'${p[35]}' 2>&1' '-c Print\ :Label 2>&1' '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'Beac|caug|dead[^bl]|FAIL|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,[lps]*.conf,pam.d,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}* .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A1 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D23 14 2 48 43;D13 4 5 32 1;D22 4 4 50 0;D13 14 3 49 5;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with "Model Identifier." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Airport Base Station No Longer Found in Network

Since applying the 10.5.2 upgrade yesterday my home network, routed via a cable modem and a formerly dependable original Airport Base Station, is no longer recognized by Airport Utility... and the Airport icon in the finder is continually scanning. I have found, however, that my network shows up as an available option in Network System Preferences...with a Connected status and an IP address (10.0.1.3).
I can connect to the internet and read email from my main iMac because I am also connected directly via ethernet, but my laptop can't find the Airport base station, either. I have reset, unplugged, restarted, check connections and cables, etc. Both Macs easily find my Airport Express, however. I'm concerned the new update no longer supports the original base station...
On another (unrelated?) note, my external backup HD (250GB Seagate), connected by Firewire, is now recognized as "Read Only," whereas it has always had read/write permission (confirmed in Get Info). So now my backup is failing, too. Sorry to introduce a new topic, but I'm frustrated!

Firmware is uploaded onto the base station itself and is different from AirPort Utility. Although you probably cannot confirm it without connecting to the base station, I think it highly unlikely that you use a firmware version earlier than 6.1.1 (which came out in 2004). If newer firmware is contained in software on your computer, AirPort Admin Utility and/or AirPort Utility should have prompted you to upload it to the base station, whereas if it is not on your computer, Software Update (assuming you use it) should have prompted you to obtain it. Even if your firmware is older than version 6.1.1, the reset procedure is virtually the same--in that case, you won't see the AX's status LED flashing rapidly a few seconds after you start holding the reset button, and you will just need to hold the reset button for 10 full seconds.
Once you connect to the base station, you should be able to see the firmware version (e.g., "Base Station Vx.x" where x.x is the firmware version) on the opening screen of AirPort Admin Utility for Graphite and Snow, when the base station is highlighted. I imagine that AirPort Utility shows similar information. I believe that in AirPort Utility, you can also check to see if newer firmware is available from Apple (choose "Check for Updates" in the AirPort Utility menu). To the best of my knowledge, the most current firmware version for AirPort Express is 6.3.

Has anyone else's Airport base station died?

Similar Messages

Maybe you are looking for