Has anyone had success using NI PCI cards at -20C? My specific needs are for RS-422/482 and GPIB cards.

NI cards have been qualified to operate only to zero degrees C. I need serial abd GPIB PCI cards that operate to -20C for military application. Has anyone had success using these cards at this lower operating temperature?

Hi,
I am not sure if this helps, but the ENET-232 is spec'd to operation at -40 degrees C.
Best Regards,
Aaron K.
Application Engineer
National Instruments

Similar Messages

  • Has anyone had success using SharePoint and FrameMaker 10 together using CMS?

    Has anyone had success using SharePoint and FrameMaker 10 together using CMS?

    Thanks for reminding to at least update the results thus far.
    Update 4:
    I did get quite a bit of support initially although slowly over a period of a month or so. After Adobe FM support and my SharePoint systems engineer reviewed how FM10 was setup on my computer (which I am the admin for our department’s SP site) and how it interfaces with our SharePoint 2010 Enterprise Edition, there was two conclusions:
    Basically Adobe FM Support said that FM10 did not support claims-based authentication and they can no longer help me. They said it will work with FM11 when it comes out.
    My SP Systems Engineer, said that FM10 is connecting to SP 2010 just fine but that the FM10 has a software glitch that causes FM10 lose control when executing checkout procedure within FM10. I can checkout and edit that same file in SP with no problems.
    About a month later, I upgraded to FM11 and ran into the same problem. I attempted to get Adobe FM Support to help and they said they will look into and get back to me. That was in July and I have not heard anything more from them, and to be honest, my schedule has been extremely busy the last 5 months that I have not had time to pursue it any further.
    Needless to say, I was very disappointed with the SP interface and, overall, the lackluster support I received from Adobe. Having a working SP interface was one of the criteria for purchasing TCS3.5 (and subsequent upgrade) in the first place.
    One thing of note, we migrated from SP 2007 to SP 2010 in February 2011 and, at the time of Adobe support, I still had access to my SP 2007 site. FM10 and FM11 had to no issues working with SP2007. Unfortunately, SP 2007 is not an option for me anymore.
    Also, another observation of FM10/11 not working with SP 2010, it seems that FM10/11 is automatically configured to work with SharePoint Drafts folder locally when connecting to the SharePoint library. This worked just fine with SP 2007 but SP 2010 does not use SharePoint Drafts folder locally the same way (the programming changed, don’t recall where I saw it, probably when searching this issue online)  and I suspect that is one of the main issues why it does not work correctly.
    So at this time, I have not found a working solution to this problem.

  • Has anyone had success using the player in a facebook newsfeed

    I'd like to use the player as a previewer in a facebook newsfeed. Has anyone had success? Is there a recipe for this?
    Thanks,
       Leo

    The Juniper VPN is a SSL-based VPN solution whereas the native client supports L2TP and PPTP only - in other words they're completely different beasts.
    That said, you shouldn't have any issue connecting to the SSL-VPN. I do it almost daily. You may need to be running the latest (or at least, recent) software on the Juniper box, though - earlier versions of the Juniper software had problems.

  • Has anyone had success using BookShare DAISY files on an iPad?

    Any info on when the Read2Go app will be available for the iPad 2?

    According to their webiste, it says "Coming Soon".  No one here would have any more info than that.
    I suspect it's been submitted to Apple for approval.  Your best bet is to contact the developer.

  • Has anyone had success with Apple replacing their iPhone 4 [out-of-warranty] concerning the stuck power button?

    Has anyone had success with Apple replacing their iPhone 4 [out-of-warranty] concerning the stuck power button?

    For $149 they will do an out-of-warranty replacement.

  • Has anyone had trouble using Adobe Support on line?

    Has anyone had trouble using the Adobe support on line?  For two days, I have tried to use the support system which requires a phone call and being put on hold or a call back of up to one hour wait long.  Four or five times my call was dropped shortly after the agent began to work with me..  One female agent was unable to find my adobe Lightroom serial # registered, so threatened to drop the call.  My # was used a couple of days to download Lt. Rm 3.6.  I asked to speak with her manager, she put me on hold, and hung up the phone after 20 mintues.  I did get her name in case anyone from Adobe  is interested.  I tried again and again to get help, but each time it ended in a hang up.  Does any one know how to get to an agent who can really help?  I am beyond frustration. 

    Try asking your question here, instead. There are lots of people here with great expertise, even though we don't work for Adobe.
    Hal

  • I'm running AutoCAD LT 2012 on my powerbook. Has anyone had experience using AutoCAD after installing Mavericks?

    I'm running AutoCAD LT 2012 on my Macbook Pro. Has anyone had experience using AutoCAD after installing Mavericks?

    Autodesk just released an update for AutoCAD 2013: http://forums.autodesk.com/t5/AutoCAD-for-Mac/Autocad-2013-compatibility-with-Ma vericks/m-p/4561479
    I do not know if a similar one will be required for AutoCAD LT so be sure to check their website.

  • Has anyone had the problem of the sound on the iPad not working on anything but the music and videos?  The sound does not work on any of the apps.

    Has anyone had a problem of not getting sounds when using apps but you can still listen to music and hear videos?

    Try reset iPad
    Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
    Note: Data will not be affected.

  • Has anyone had the problem with their iPhone 5 where some people cannot receive texts from you?  And if so, is there a fix?

    Has anyone had the problem of not being able to send texts to certain people? 

    Here is another screenshot.  In this example, I did 'Get Info' on one of the goofy ones, and it shows that this Wolfmother song is sorted by the Eagles.  ***? 

  • Has anyone had success in running Bootcamp along side vmware Fusion?

    The only program I need windows for is Autodesk REVIT (A 3D CAD House modeling program) I use my mac for everything else.
    REVIT takes up alot of memory and needs a decent video card to run well. When I tried using bootcamp, the program (REVIT) ran smoother than any windows platform we had, but I had no access to any of my mac programs without shutting down and rebooting.
    I tried running vmware fusion and starting my bootcamp partition but everytime I switched from bootcamp to fusion, my windows said I had some major hardware changes and I needed to re-register my windows license. the license issue was also occuring with REVIT.
    I'm wondering if anyone else has had these problems. I am willing to reinstall my windows partition to make it so I can switch from FUSION to BOOTCAMP smoothly. I use BOOTCAMP when I am in crunch mode and FUSION when I want to use my mac applications the same time as REVIT.
    Any help would be appreciated. THANKS

    I haven't had any trouble with Fusion and Boot Camp. I think activation does need to occur once on each side (once in Fusion and once in Boot Camp). Windows use the MAC address of your NIC to determine the hardware, and Fusion generates a MAC for the the virtual NIC that is obviously different from the MAC of your actual NIC in your Mac.
    I bought MacDrive so that I could have access to my HFS partition of my hard drive when booted into Windows. The product works great, but also complains about activation when run in Fusion. MacDrive doesn't seem to want to stay activated in both Fusion and Boot Camp at the same time, so I leave it activated via Boot Camp and not activated for Fusion, since I can use Shared Folders instead. (that and it still seems to work anyway).
    What did you mean by "crunch mode"? On a deadline? Is that because your software is too slow when running XP with Fusion? It seems like running XP through Fusion is the way to go for you 97% of the time, so I would worry about getting your CAD software going in Fusion and not worry so much about Boot Camp.
    Best of luck.

  • Has anyone had success in getting Apple to correct Maps mistakes?

    On multiple occasions I've submitted a correction using the function within Maps to report errors, but nothing is ever done.  Has anyone ever had any success in getting Apple's attention and getting something fixed?  Or is the submitting a correction feature just a black hole?  I've had to tell friends with iPhones to always use Google Maps rather than Apple to navigate their way to my house because Maps has completely mislabeled the street outside my development.  It sure would be nice if they had a human being you could call...

    For users who's printer/scanner does not have a compatible driver from their manufacturer:
    How do I scan or print with the driver from Apple Software Update?
    Depending on your printer and the type of driver update, you might need to scan in a different way than you did before you installed Mountain Lion.
    Scan from the Print & Scan window:
    Place the item that you want to scan on the scanner glass, or load it into the automatic document feeder (ADF) if your printer has one.
    Click the Apple menu (# ), and then click System Preferences .
    Click Print & Scan (# ).
    Click your printer in the left pane.
    Click the Scan tab, and then click Open Scanner .
    Click Show Details . The details of the scan display, including options to change scan settings.Figure 5: Show Details scanning screen# Image: Show Details scanning screen
    Change any settings as necessary, and then click Scan .
    NOTE:
    Make sure to select either the Flatbed mode or the Document Feedermode, depending on your printer and how you plan to scan.
    Hope this helps

  • Using SUMIFS on iPad Numbers has anyone had trouble using the keypad relational symbols in the "conditions" field?

    The iPad Numbers has a very nice data entry keyboard for expressing conditions.  They have the usual =, <, > but also have the single symbol version of >=, <= and <> (as an equals with a slash through it), however, if you try to use these keypad keys in the conditions field of the SUMIFS, it returns a syntax error.  After seeing some examples of Numbers '09 I discovered I had to express a relation inside double quotes, " ", which means the text keyboard is displayed and the very nice data entry keyboard is gone along with the nice symbols.  Has anyone seen this and am I doing something wrong or is this another bug?  Thanks.

    The xxxIF functions have (for as long as I have used them) required a text string as the argument unless it was equal to a value of a cell, with no logical operators. so it is not something new, its been that way for decades and I personally think Apple might have done it differently if they didnt have to maintain compatiability with older spreadsheet programs.
    i.e. not a bug, ensures backward compatability.
    Jason

  • Has anyone EVER successfully used BlackBerry Bold BlueTooth DUN w/ iBook ?

    Greetings all,
    I have spent days trying to get my iBook G4 running OS 10.4.11 to successfully connect to the internet via BlueTooth through my BB Bold's supposed dial-up networking capabilities. I have followed endless threads in multiple Mac, Black, Crack, and other forums and have watched countless video demonstrations. None of the info I have found has worked, probably because every source of info involved either a different BlackBerry model, a different Mac model, or a different OS version.
    I get the same Internet Connect error every time: "A modem error occurred. Please check your settings and try again."
    I have tried multiple dial-up isp's and multiple access numbers. I do not claim to be an expert, but I have worked as a network administrator, have set up multiple network devices, and have a pretty good understanding of internet and general network technologies and this is just driving me insane.
    If anyone actually knows how to accomplish this task, I would be eternally grateful for step-by-step instructions or even just some insight into how I might determine what type of "modem error" occurred!
    Please do not tell me to purchase an iPhone or a tethering plan. If those were viable options at the moment, I would not be wasting our time here. Thanks!

    Ditto on both points. Meanwhile I use the solution of a third party backup.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • NI PXIe-1620Q - has anyone had success writing device drivers for Fedora 15? I am trying to control a PXI-6509.

    I am using Fedora-Core 15 with kernel, 2.6.43.8_1.fc15.i686. I am trying to use NI-KAL ver 2.1 which does not support my version. But it compiles, the nikal driver loads correctly. But after a rebboot it crashes.
    Has anyone built any version of NI-KAL that will work with FC15? or via the DDK? 

    Hi p_borras,
    Is there a specific error associated with the crash you are experiencing?
    Thanks,
    Daniel D.
    National Instruments
    Automated Test Software R&D

  • Has anyone had luck using NoiseHush NS560 headphones?

    These Bluetooth headphones provide REALLY slow playback when used with Logic Pro. Is there a clock difference between the Bluetooth protocol and the "default" for Logic playback?

    UPDATE: I just tried Hype 3 Professional and Gitden Reader didn't crash on the animation this time. It still goes full screen, but allows you to go back to the epub. Hurray! Publiwide Reader still gives an error though.

Maybe you are looking for