Has anyone managed to install RAID 0 with 975x PowerUp ?

Out of curiosity, has anyone on here managed to install XP on RAID 0, using 2 SATAII drives ?
I've had problems (another post) ... but I was just curious if anyone has managed to do it.
If so, can you confirm ...
a) what slots in the mobo you put your SATA drives in (there is that single 'special' SATA connector!)
b) what driver did you use for the F6 method.
I just want to see if anyone has managed to do what I have utterly failed to do ...
Thanks,
S.S.

Quote from: SpencerSteel on 18-September-06, 01:49:59
Out of curiosity, has anyone on here managed to install XP on RAID 0, using 2 SATAII drives ?
I've had problems (another post) ... but I was just curious if anyone has managed to do it.
If so, can you confirm ...
a) what slots in the mobo you put your SATA drives in (there is that single 'special' SATA connector!)
b) what driver did you use for the F6 method.
I just want to see if anyone has managed to do what I have utterly failed to do ...
Thanks,
S.S.
Are you still having problems installing windows on RAID? PrvtMsg me if you want some help.
Incidentally you should be using two of the five main SATA ports, enabling RAID in the SATA section (forget the JMicron - disable it)
Next you should be able to enter the Intel RAID config Mgr WHILST the system is POSTing, and set up your RAID volume from there.
This should enable you to use the Intel RAID drivers on a floppy disk.
Quote from: smokinkane on 18-September-06, 22:31:04
I have 2 seagate 7200.10 (perpendicular recording) drives in RAID 0 on the intel controller, no problems at all. This config rips, its unreal, I'm sure it gives all of raptors except the new version a serious headache, haha.
Really? what sort of benchmarks are you getting? I use HDTach for HDD Benching.

Similar Messages

Has anyone managed to install aperture 2 with a 12" G4 laptop?

Mine runs Leopard 10.5.2 with a 1.5 Ghz processor and 1.25GB of memory. The system checker says it's fine but it tells me my graphics card will not work it properly. My graphics card is the GeForce FX Go5200.
Has anyone managed to get it installed, it's blinkin annoying that i cannot load it on this laptop?

I've got it running now on my 12" 1.25 PB with 768Mb of RAM, it took some fiddling but it is running now. On launch it tells me 'The version of ImageIO installed on your computer is not supported by Aperture' but still gives me the option to continue and from there it launches as normal.
It appears that my Nikon D3 files are not supported but earlier cameras like my D200 are fine. My PB is running 10.4.11 btw.
I'm not sure I'm allowed to explain how I got it running here, I've no wish to contravene any forum rules but you can contact me at flateric1 AT mac.com and I can give you my iChat name to talk you through it if you wish.
FlatE

Has anyone managed to install airport/bluetooth manually?

I am aware of the issues as discussed ad nauseum (and yes I was sold one of the old exterme cards ahead of my purchase of a quad!)
I know where to buy the correct kit from US but would like to know whether anyone has managed to install it manually (yes I know it is not user-installable and it affects the warranty)

Yes, I have the Powermac g5 quad and I tried two of them. The first one barely worked and the second worked for only short spurts and its very difficult to install. I had the same luck as others who tried that product on this forum. I ended up buying a usb keychain 802.11b/g from ZyXEL p/n AG-225H. Some of the boxes at CompUSA advertised that it was MAC compatible if you downloaded a driver from us/zxel.com/ag225h. It works for several hours at a time and then a kernel panic crashes my computer. I have talked to ZyXEL and they believe that its just one bad unit. I going to return it tomorrow and get a new one. If it still crashes they want me to work with there Apple expert to troubleshoot and fix the problem.
Hope this helps....Tracy

Has anyone managed to get Authorization working with JAAS from CusLoginMod?

Hi everybody,
I am on a standalone oc4j 10.1.3.1.0
I want to be able to access a private resource using form based authentication
and I would like to use JAAS from with a custom login module.
The authentication part works just fine but the authorization doesn't seem to happen.
Both login() and commit() from my LoginModule are called and after authentication takes place, the subject is populated with the right Principals, in my case "testers".
This Subject then it should be matched against the <security-role> defined in my application's web.xml
This is the part from my application's web.xml which holds the security information.
<security-role>
<description>Online User</description>
<role-name>testers</role-name>
</security-role>
<security-constraint>
<web-resource-collection>
<web-resource-name>access to the private application</web-resource-name>
<url-pattern>/faces/user/*</url-pattern>
</web-resource-collection>

<auth-constraint>
<role-name>testers</role-name>
</auth-constraint>
<user-data-constraint>
<transport-guarantee>NONE</transport-guarantee>
</user-data-constraint>
</security-constraint>
<login-config>
<auth-method>FORM</auth-method>
<form-login-config>
<form-login-page>protected.htm</form-login-page>
<form-error-page>error.jspx</form-error-page>
</form-login-config>
</login-config>
Has anyone faced this scenario before?
Any advices much appreciated
thank you.

I can't see what am I missing if I'm missing something.
This is my orion-application.xml
<orion-application xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="http://xmlns.oracle.com/oracleas/schema/orion-application-10_0.xsd">
<jazn provider="XML" jaas-mode="doAsPrivileged" location="">
<property name="role.mapping.dynamic" value="true"></property>
<property name="custom.loginmodule.provider" value="true"></property>
</jazn>
<jazn-loginconfig>
<application>
<name>JAAS</name>
<login-modules>
<login-module>
<class>jaas.JAASLoginModule</class>

<control-flag>required</control-flag>
<options>
<option>
<name>debug</name>
<value>true</value>
</option>
<option>
<name>log_level</name>
<value>ALL</value>
</option>
</options>
</login-module>
</login-modules>
</application>
</jazn-loginconfig>
</orion-application>

Has ANYONE managed to install Vista under Boot Camp on a second drive?

As I understand it Vista cannot be installed on secondary drive because of the "Windows is unable to find a system volume that meets its criteria for install" error message when selecting the install location because it needs a Primary Drive.
In the Microsoft Knowledge Base they recommend removing the primary drive to overcome this but I tried and it failed.
Do I HAVE to go out and buy XP (which allows installs on secondary drives) and then upgrade to Vista.
I'm so darn frustrated with this issue I wondered if anyone has managed to do this successfully.
Thanks
Aln

No problems here. I have Vista 64 Ultimate running on a different internal drive, and I didnt remove my primary OSX drive to do this. In fact it worked without a hitch. There must be something you are doing wrong in the bootcamp preparation phase.

Has anyone managed to install gimmie?

I'm trying to build gimmie, but I don't know why it refuses to run, it sas pygtk wasn't build with python numeric suport or something like that, but I haven't been able to find anything like that in the web.

Phrodo_00 wrote:
Blaasvis wrote:make install wasn't implemented.
that's why make install didn't worked. Thank you.
I tried searching google for this gimmie you're speaking off. What is it? Sorry for the random post, but you caught my interest xD

Has ANYONE managed to get OS2 working with WiFi and bridge?

I've scoured the forum, and tried everything - right now, its a cute, flat paperweight.

I have!
If you are having the same problems as me, on update, I had no wifi connections at all - didn't find a single one, despite the area being overrun with wifi networks.
Connect your paperweight, I mean, Playbook, to the Desktop Software, take a backup, then do a security swipe and reset the whole thing.
With mine, as soon as it came back on after the swipe the wifi was working correctly.
I re-connected it to the Desktop Software, accepted any updates it was offering, then restored my backup from this morning.
Hey presto! A fully functioning Playbook!
Good luck!

Has anyone in this Forum had problems with installing and running Adobe apps on the new MacPro?

Has anyone in this Forum had problems with installing and running Adobe apps on the new MacPro?
I have been trying to install Photoshop CS6 & CC and Acrobat Pro XI on my Mac Pro (late 2013). I keep getting a 'configuration' error message and wondered if the problem was wide spread.
TIA,
Jerry

Thanks, Martin.
Good to hear someone has had success. The lack of it here is frustrating and depressing.
Thanks again,
Jerry

Has anyone managed to get a PS3 Controller to work with OSX Lion?

Hi,
I wanted to connect my PS3 controller to my iMac (late 2011) using bluetooth but have been unable to do so. It will connect for a brief time but then it will lose connect as it has not paired. It also asks me for a pairing code. I have tried 0000 and this does not work. I have searched the internet and it seems this is a common issue. Has anyone managed to get it working?
Does anyone know if Apple plan to fix the issue with a forthcomming update?
Cheers,
Tim

There are numerous threads on this, please use the "More Like this" tool, you will find it on the right. I'm not sure if anyone has any solutions but that is the logical place to start.

Has anyone managed to deploy Acrobat Pro 9.0 for Mac through ARD?

Has anyone managed to get Adobe Acrobat Pro 9.0 for Mac to deploy with any level of reliability through tools such as Apple Remote Desktop?
The main CS3 apps are "better", if still kludgy to deploy somewhat silently, but every time I've tried to get Acrobat Pro 9.0 to deploy, it steadfastly refuses to do so without demanding admin access on at least the first launch, and insisting on running the Updater in the process, which is completely unacceptable.
I should say that I've looked at their Adobe Acrobat deployment site (http://www.adobe.com/products/acrobat/solutions/it/), and it's entirely useless for the Mac version.
Why do Adobe make this so hard?

Okay, I think I've figured this out.
* On a clean machine (ie: no Adobe software), install Adobe Acrobat Pro
* Run Acrobat. Insert license code. Allow it to "selfheal". Quit.
* Run Distiller. Allow it to "selfheal". Quit.
* Edit AcroEFGPro90.plist and AcroEFGDist90.plist which can be found in Contents > MacOS within the Acrobat and Distiller apps respectively.
* Change the "Requires" tags from "YES" to "NO" for all the file resources.
* Copy these to plist files into /Library/Application Support/Adobe/Acrobat/ and overwrite the ones that are already there.
* Run Acrobat and Distiller again. Allow "selfheal" if prompted. Quit.
* Run again. Quit.
* Build a Mac OS X installer package of the following:
/Applications/Adobe Acrobat Pro 9.0
/Applications/Utilites/Adobe Utilities
/Library/Application Support/Adobe/
/Library/Application Support/FLEXnet*
/Library/Preferences/com.adobe.*
/Library/Preferences/FLEXnet*
/Library/Internet Plug-ins/AdobePDFViewer.plugin
/Library/ColorSync/Profiles/
/Library/Printers/PPD Plugins/Adobe*
/Library/Printers/PPDs/.../.../.../ADPDF9.PPD (one per language)
/Users/Shared/Adobe
/usr/libexec/cups/backend/pdf900
* After you've built the package, go through the Acrobat application bundle and find cupshup.pl. Copy it into the Resources folder of the installer package, and rename it to "postflight" (this gets the installer to configure the PDF printer).
* Distribute through ARD.
* Grab com.adobe.* from ~/Library/Preferences
* Distribute the com.adobe.* files to all users; the .plist files can be done through Workgroup Manager, however com.adobe.118.registration must be copied as-is into the user folder, rather than being injected via MCX or the defaults command or any other method, as it's not a plist.
Dear Adobe,
MAKE THIS SIMPLER.
Your Friend,
etc...

Has anyone managed to get a 3TB dynamic disk on Windows 2003 Server?

I just got a pair of new 3TB disks that I wanted to put on my Windows 2003 server enterprise x64 system, SP2, all updates installed.
When I first tried to convert to dynamic, I got the error "The operation did not complete" as described in this KB article
http://support.microsoft.com/kb/826823
It says there is a patch, but there is not one for x64, just x86 and ia64
I found another technet discussion here: https://social.technet.microsoft.com/Forums/en-US/winserverfiles/thread/cb62238c-b3d0-4989-b45a-ae6de6701a7b?stoAI=10
However its best suggestion is to use a product from AOMIE, but I tried that and it didn't even recognize the disk. It also suggests that one needs a better version of diskpart.exe and to try to the 32 bit version. Anyone have any experience
with that?
I also tried creating moving the disk to Windows 7 x64, making it dynamic there, but when I move the disk back to 2K3 it does not recognize it, and goes back to a 2TB partition. I also saw something about needing a 512 block size for 2K3, but W7 does
not allow anything smaller than 1K.

Hi,
During my research, if found the following artcle which also mentioned a 3TB disk should be supported in Windows 2003 SP1:
Has anyone managed to get a 3TB dynamic disk on Windows 2003 Server?
http://social.technet.microsoft.com/Forums/en-US/winserverfiles/thread/a720ae72-0c04-44dd-94c0-2e6aecce530e
So I contact the author about this issue. He said it could be caused if your hard disk is a 512e drive as the 3TB drives on the market today are normally 512e drives.
However manufacturers stopping identifying this, and if the controller is old, FSUtil will not able to identify a 512 drive but recognized it as a normal 512n drive.
Thus please provide the drive model so we could search on manufacturer's website for exact information.
Also please paste the screenshot in your reply which Satish mentioned if available.
In addition, here is an article Robert provided:
http://www.windowsitpro.com/article/what-would-microsoft-support-do/support-advanced-format-hard-drives-141584

Has anyone managed to load a movie on their Moza

I've bought two of these things for the kids this Christmas, and I can load pictures, and music, but I can't seem to load any of my movies. Has anyone else While in the Central Software it shows the file transferring, it take a long time but finally gets to 00%. When I try to view it on the mp3 player it plays 5 seconds, and that's it. It obviously didn't transfer everything. It plays in Media Player as well. I tried to transfer it using media player too. It locks up and I have to end the program. I need a hammer.

Re: Has anyone managed to load a movie on their Mozaic i With a screen resolution of 28 x 60 you're going to be hard-pressed to get great quality from downscaling a full-size movie. That said, you dissatisfaction with the movies converted by this Daniusoft application may simply indicate the compression level was too aggressi've. That would appear as blocky or splotchy areas during playback or freeze frames. With any converter you need to balance between the quality setting and the final output file size.
If you search the forum you'll find mention of an application called BADAK http://www.robbiek.com/badak.htm. It is a free converter that is significantly faster than the once Creative bundles that has a preset option for the flash Zen. Those setting will probably work reasonably well for the Mosaic if you change the output resolution from 320x240 down to 60x28. However, I don't have a Mosaic so I'm speculating. Even so the presets may not be ideal for some source video being converted. Quality video transcoding is a "fiddle with it" process not a "one-button" process.

Has anyone managed to get HP Warranty Information into SCCM?

Has anyone managed to get HP Warranty Information into SCCM?
I have tried a few scripts that I found on the net but none of them seem to work as I believe HP updated there site this year..

OK, I played around a bit (scripting from a web page isn't way beyond me) but... a few caveats. My lab isn't available right now; so all I could test was that the script ran on an HP laptop. A single HP laptop. and created the regkeys in
(in my case) HKLM\software\wow6432node\CompanyName\WarrantyInformation. So... one single test on one single workstation, and no testing of the mof edit means... I'll need your help to confirm it works.
Anyway, below is the script. Other caveats: It drops a log, and then continuously adds to the log file in %temp% (of the SYSTEM, which is using %windir%\temp). So depending upon what you want/need--you may want to change the EnableLogging
= True to EnableLogging = False (once you confirm it works on all/most of your boxes). The other caveat, of course, is to change the sCompanyname = to be your Company Name; although I suggest you don't have spaces or special characters in it. Short
'n' sweet. Then, naturally, once you have a box with the regkeys, use Mark Cochrane's RegKeytoMof 3.0 or higher to build the mof edits for you to paste to the bottom of your configuration.mof and sms_def.mof. In that blog above Eric Schloss was
using DCM as the delivery method to deliver the script to populate the regkeys--that worked for him and I see no reason it wouldn't work for everyone--so once you've tested the script interactively from a psexec -s -i cmd.exe shell on an hp box (to see it
create the regkeys) I'd make a DCM like Eric did and target a collection with a few HP laptops or desktops and confirm it works via the DCM.
Anyway, give this a try--again... only tested on 1 single, lonely little HP laptop. Needs a bigger test base!
Edit: and... even using Regkeytomof sometimes regkeys can be tricky. If the mof edit doesn't work right to pull the data back, post what you've added. someone here can usually spot if there's something not right about it and help you fix
the mof edit.
Edit #2: removed bad space, and bad copy/paste job as discovered by sevengs. Thanks!
on error resume next
EnableLogging = True
sCompanyName = "CompanyName"
Set oShell = CreateObject("wscript.Shell")
Set fso = CreateObject("scripting.filesystemobject")
strTemp = oshell.ExpandEnvironmentStrings("%temp%")
If EnableLogging Then
Set oLogFile = fso.OpenTextFile(strTemp & "\WarrantyInfo.log", 8, True)
oLogFile.WriteLine "*********************************************************"
End If
WriteLog "Beginning warranty information lookup."
sWebServiceHost = "http://h20000.www2.hp.com/bizsupport/TechSupport"
sWebServiceURL = "WarrantyResults.jsp"
sWebService = sWebServiceHost & "/" & sWebServiceURL
'Get the system's serial number from WMI
Set oWMIService = GetObject("winmgmts:\\.\root\cimv2")
Set colItems = oWMIService.ExecQuery("Select SerialNumber from Win32_BIOS",,48)
For Each objItem in colItems
sSerialNumber = objItem.SerialNumber
Next
WriteLog "Serial number of system is " & sSerialNumber
'Get the Product ID from WMI
Const wbemFlagReturnImmediately = 16
Const wbemFlagForwardOnly = 32
lFlags = wbemFlagReturnImmediately + wbemFlagForwardOnly
strService = "winmgmts:{impersonationlevel=impersonate}//./root/HP/InstrumentedBIOS"
strQuery = "select * from HP_BIOSSetting"
Set objWMIService = GetObject(strService)
Set colItems = objWMIService.ExecQuery(strQuery,,lFlags)
sProductNumber = ""
For Each objItem In colItems
If objItem.Name = "SKU Number" Then
sProductNumber = objItem.Value
End If
If objItem.Name = "Product Number" Then
sProductNumber = objItem.Value
End If
Next
If Len(sProductNumber) = 0 Then
WriteLog "ERROR: Product Number could not be determined."
oLogFile.WriteLine "*********************************************************"
oLogFile.Close
WScript.Quit(9)
Else
WriteLog "Product number of the system is " & sProductNumber
End If
Set colItems = oWMIService.ExecQuery("Select AddressWidth from Win32_Processor",,48)
For Each objItem in colItems
sAddressWidth = objItem.AddressWidth
Next
WriteLog "Operating system is " & sAddressWidth & " bit."
'Define the parameters string to send to the web site
sParameters = "nickname=&sn=" & sSerialNumber & "&country=US&lang=en&cc=us&pn=" & sProductNumber & "&find=Display+Warranty+Information+%C2%BB&"
WriteLog "Opening the web site URL " & sWebService & "?" & sParameters
'Define and call the web site
Set oHTTP = CreateObject("Microsoft.xmlhttp")
oHTTP.open "GET", sWebService & "?" & sParameters, False
'oHTTP.setRequestHeader "Content-Type", "application/x-www-form-urlencoded"
oHTTP.send
If oHTTP.Status = 200 Then
WriteLog "Successful response from the web site."
'WriteLog oHTTP.ResponseText
Process oHTTP.ResponseText
Else
WriteLog "ERROR: the web site returned status code " & oHTTP.Status
WriteLog "Returning exit code 1."
nExitCode = 1
End If
If EnableLogging Then
oLogFile.WriteLine "*********************************************************"
oLogFile.Close
End If
WScript.Quit (nExitCode)
Function Process (HTML)
WriteLog "Processing the HTML returned from the site."
intSummaryPos = InStr(LCase(html), "serial number")
If intSummaryPos = 0 Then
Process = ""
Exit Function
End If
intSummaryTable1Start = InStrRev(LCase(html), "<table", intSummaryPos)
intSummaryTable1End = InStr(intSummaryPos, LCase(html), "</table>") + 8
intSummaryTable2Start = InStr(intSummaryTable1End, LCase(html), "<table")
intSummaryTable2End = InStr(intSummaryTable2Start, LCase(html), "</table>")
table1 = getStr(intSummaryTable1Start, intSummaryTable1End, html)
table2 = getStr(intSummaryTable2Start, intSummaryTable2End, html)
const HKLM = &H80000002
Set oReg=GetObject("winmgmts:{impersonationLevel=impersonate}!\\.\root\default:StdRegProv")
sKeyPath = "SOFTWARE\" & sCompanyName & "\WarrantyInformation"
WriteLog "Registry key path is HKLM\" & sKeyPath
oReg.CreateKey HKLM,sKeyPath
WriteLog "Processing the first table from the web page."
arrGeneral = processTables(table1,1)
'arrGeneal should be in the form Serial Number, Product Number, Product Line, Product Description, Warranty Check Date
WriteLog "Processing the second table from the web page."
arrContracts = processTables(table2,2)
'arrContracts should be in the format Warranty Type, HW Warrenty Start Date, HW Warranty End Date, HW Warranty Status, Setup Warranty Start Date, Setup Warranty End Date, Setup Warranty Status
WriteLog "Setting registry values."
WriteLog "SerialNumber is " & arrGeneral(0)
oReg.SetStringValue HKLM, sKeyPath, "SerialNumber", arrGeneral(0)
WriteLog "ProductNumber is " & arrGeneral(1)
oReg.SetStringValue HKLM, sKeyPath, "ProductNumber", arrGeneral(1)
WriteLog "SerialLine is " & arrGeneral(2)
oReg.SetStringValue HKLM, sKeyPath, "ProductLine", arrGeneral(2)
WriteLog "SerialDescription is " & arrGeneral(3)
oReg.SetStringValue HKLM, sKeyPath, "ProductDescription", arrGeneral(3)
WriteLog "WarrantyCheckDate is " & CStr(CDate(arrGeneral(4)))
oReg.SetStringValue HKLM, sKeyPath, "WarrantyCheckDate", CStr(CDate(arrGeneral(4)))
WriteLog "WarrantyType is " & arrContracts(0)
oReg.SetStringValue HKLM, sKeyPath, "WarrantyType", arrContracts(0)
WriteLog arrContracts(1)
WriteLog "HardwareWarrantyStartDate is " & CStr(CDate(arrContracts(1)))
oReg.SetStringValue HKLM, sKeyPath, "HardwareWarrantyStartDate", CStr(CDate(arrContracts(1)))
WriteLog "HardwareWarrantyEndDate is " & CStr(CDate(arrContracts(2)))
oReg.SetStringValue HKLM, sKeyPath, "HardwareWarrantyEndDate", CStr(CDate(arrContracts(2)))
End Function
Function getStr(startpos, endpos, data)
Dim tmp
'Get the substring
tmp = Mid(data, startpos, endpos - startpos)
' Remove end of line
tmp = Replace(Replace(Replace(tmp, VbCrLf, ""), vbCr, ""), vbLf, "")
getStr = tmp
End Function
Function processTables(table, ttype)
' Remove HTML Tags and replace with "|"
Set re = New RegExp
re.Pattern = "<[^>]+>"
re.IgnoreCase = True
re.Global = True
table = re.Replace(table, "|")
table = Replace(table, " ", "")
table = Replace(table, ":", "")
table = Replace(table, " ", "")
' Remove excess |
re.Pattern = "[|]+"
table = re.Replace(table, "|")
' Clean up a bit more
re.Pattern = "\|\s+\|"
table = re.Replace(table, "|")
' Remove | from start and end of string
re.Pattern = "^\||\|$"
table = re.Replace(table, "")
arrTable = Split(table, "|")
arrTmp = ""
If ttype = 1 Then ' General Info Table
i = 1
For Each cell in arrTable
Select Case LCase(Trim(cell))
Case "serial number"
sSerialNumber = arrTable(i)
Case "product number"
sProductNumber = arrTable(i)
Case "product line"
sProductLine = arrTable(i)
Case "product description"
sProductDescription = arrTable(i)
Case "date of warranty check"
sCheckDate = arrTable(i)
End Select
i = i + 1
Next
arrTmp = sSerialNumber & "|" & sProductNumber & "|" & sProductLine & "|" & sProductDescription & "|" & sCheckDate
ElseIf ttype = 2 Then ' Contract Info
i = 0
For Each cell in arrTable
cell = Replace(cell," ","")
if Instr(lcase(trim(cell)),"wty hp hw maintenance onsite support") > 0 then
cell = "wty hp hw maintenance onsite support"
end if
if Instr(lcase(trim(cell)),"wty hp hw maintenance offsite support") > 0 then
cell = "wty hp hw maintenance offsite support"
end if
if Instr(lcase(trim(cell)),"wty hp support for initial setup") > 0 then
cell = "wty hp support for initial setup"
end if
Select Case LCase(Trim(cell))
Case "warranty type"
sWarrantyType = arrTable(i+8)
Case "wty hp hw maintenance onsite support"
sHWStartDate = arrTable(i+1)
sHWEndDate = arrTable(i+2)
sHWStatus = arrTable(i+3)
Case "wty hp hw maintenance offsite support"
sHWStartDate = arrTable(i+1)
sHWEndDate = arrTable(i+2)
sHWStatus = arrTable(i+3)
Case "wty hp support for initial setup"
sISStartDate = arrTable(i+1)
sISEndDate = arrTable(i+2)
sISStatus = arrTable(i+3)
case else
End Select
i = i + 1
Next
arrTmp = sWarrantyType & "|" & sHWStartDate & "|" & sHWEndDate & "|" & sHWStatus & "|" & sISStartDate & "|" & sISEndDate & "|" & sISStatus
End If
' Remove | from start and end of string
re.Pattern = "^\||\|$"
arrTmp = re.Replace(arrTmp, "")
'wscript.echo arrTmp
arrResult = Split(arrTmp, "|")
Set re = Nothing
processTables = arrResult
End Function
Function WriteLog (sText)
If EnableLogging Then
oLogfile.WriteLine Now() & " " & sText
End If
End Function
Standardize. Simplify. Automate.

Has anyone managed to change the battery in a creative Zen MX

=i bought a 6gb zen MX? in November 2007 and have used it every day since. The battery is now in a sorry state and doesn't hold a charge for more than about 4 hours. After fully charging it, if you then leave it overnight the battery almost totally depletes. The battery is definitely a goner. Has anyone opened one of these players, changed the battery and then got the thing back together successfully? I've looked around on the net but can't find any info on how i might open the player to insert a new battery. Meanwhile i've bought a new Creative ZenMX but i prefer the old one with its dedicated slider for on/off and lock and it would be great if i could somehow get a new battery into it.
I still have my old Ceati've Zen Jukeboxes (30gb and 60gb) and i wore a couple of batteries out in those. But all you had to do was open the player and shove in a new battery. Shame that facility no longer exists in Creative's MP3 players.
Any help on the issue of replacing the battery in an MX would be much appreciated.

Re: has anyone managed to change the battery in a creative Zen MX%Thanks for the links Bertwin, much appreciated.
Now i have a problem in obtaining a replacement battery. Back in the day you could phone Creative (in Ireland) and order replacement batteries but alas, no longer. On the net you can easily find replacement batteries for every Creative player.....except for the Zen MX. ? The replacement x-fi battery looks similar? and has the same wire connections but it is 3.7v as opposed to 3.6v in the MX. Also the x-fi battery is rated at? 550mAh while the MX is rated at 0.55AH. (Though i guess that could mean they are the same capacity only it's written differently)
The Creative part number for the MX battery is BAC0603R79925 and the Creative Model No is : LPC6333445
If anyone knows where to obtain this battery please post.

HT2693 Has anyone managed to download the March 2013 update of Numbers on an iPad 1?

I recently tried to update Numbers but it says download not available at this time and has just hung there every since. Has anyone managed to update Numbers and can they help please

Thanks to both of you - I was running 4.2 on my iPad, and the download link at daw.apple.com for the 4.2.1 GM was taken down after it shipped - so I was bummed...
Found your post with the direct download link - boom! Happy camper...
Aaron

Has anyone managed to install RAID 0 with 975x PowerUp ?

Similar Messages

Maybe you are looking for