Has anyone used SuperDuper to go from C2D to SR?

Has anyone here upgraded to the new santa rosa MBP from the C2D MBP and used SuperDuper to clone their system? I need to do just that and was wondering if the computer will boot and be fully functioning. I think this is the easiest way to transfer everything since I won't have my C2D MBP when I receive my SR MBP.
If this is not possible because of hardware issues, will the clone of my current system mount as an external fw drive on the SR? This way I guess I could manually copy my files over to SR.
Thanks

I would not advise doing this unless the build number on the SR machine is exactly the same as the one on the C2D. With most all new hardware releases the OS X build is usually unique for that hardware until the next general version of OS X is released. Therefore, cloning from the C2D very likely won't work.
To check the build versions select About This Mac from the Finder's Apple menu. Click on the OS X version number (10.4.9, for example) to reveal the current build version. If the build version of the SR installed OS X is not the same as that of the C2D then do not clone either operating system to either machine.
Instead use Migration Assistant.

Similar Messages

Has anyone used the Applesause Polish from Invisible Shield!

Has anyone used that stuff?
Does it work?
What about on a 3G iPod?
Thanks

I bought it and I think it´s really good. I test it against a macbook pro 13" and I found it very similar in times, sometimes the Sonnet reader beat the built in reader, usually not but sometimes it did.
It´s a little tricky to put the cards into the reader but I guess that becuse that way it´s harder to push the card out by mistake.
I also love that it can live on my macbook pro becuse it fits perfectly, no need to put it on and off evertime I use it.
But the one you are saying is not the one I bought, becuse it´s almost 50 usd the one I have
https://secure1.sonnettech.com/product_info.php?cPath=24_130&products_id=390&osC sid=d09730751ecf7cabe0210f347b4e4b20
I also bought the dual compac flash reader and I also love it, it´s extremly fast
Sorry that I didn´t answer faster but I was working and I never get the advice that I had a message.

Has anyone used av hook up from iPad 1 to tv-if so which cable?

What cable have you used for hook up?

iPad1, 64GB, 3G. I updated to iOS5 a couple of days after it was released (servers were too slow to connect on the first day. ) I had only one crash, and that was my fault. (Moved Newsstand to a folder, which is not supported.) Otherwise, all is fine. As others have noted, on the iPad1, it's a bit slower, but nothing that's a dealbreaker IMHO.
The most difficult thing has been the amount of updates to the apps. Nearly every app I have had an update for iOS5 so it was like I was seeing 3-5 new updates every day. But I've kept with the updates and I think that has helped with my lack of crashes/lockups.
My only real complaint is with the way the iPod app changed to the Music app and how it now treats podcasts. (The "previously played" indicator is now missing.) And a few minor gripes like not having location based reminders (iPhone only feature. ) But otherwise, I'm reasonably satisfied with the update on my device.
If I had to make a recommendation, I'd be on the fence. If there is a "must have" feature you want (e.g.: Airport configuration utility, Messages, Twitter integration,) then go ahead an update. Otherwise, not updating now is probably not going to inconvinience you. Eventually, there may be "iOS5 only" apps but by then, you'll probably be ready for a new iPad.

Has anyone used Migration Assistant to move services from one system running Server to a new system?

So, I've purchased a Mac mini to replace my aging Mid 2009 mini on which I've been running Mavericks Server. In trying to answer the question of how best to move services from the old machine to the new, I've stumbled into the fact that Migration Assistant can apparently migrate not just user data for workstations and laptops, but also service data for servers. The problem is there isn't much detail in the docs about how good a job it does when going from one machine to another without changing OS releases. There's a very detailed document in the KB about going from older versions of Server to new (OS X Server: Upgrade and migration from Lion Server or Snow Leopard Server) and a general doc on migrating from another Mac under Mavericks (OS X: How to migrate data from another Mac using Mavericks) but that has no details about Server.
Has anyone used Migration Assistant to move services from one system running Server to a new system? Are there any details that are particularly important to get right? Are there things that require manual steps after Migration Assistant is done?
There are other ways I could tackle the problem, of course. I could simply swap drives between the systems, but the new system has two drives that are bigger, faster, and I intend to mirror them. That would complicate such an approach. I'd really like to keep the conversation constrained to a discussion of Migration Assistant as the primary method.

yes. I migrated a server frm lion to mavericks following these notes a while back:
OS X Server: Upgrade and migration from Mountain Lion
i do not recall having any problems with it.

I was advised to purchase dazzle video creator to move analog videos from an old sony camcorder to a mac. I have purchased the dazzle and the specs seem to be for windows only. Has anyone used this product on mac?

I was advised to purchase dazzle video creator to move analog videos from an old sony camcorder to a mac. I have purchased the dazzle and the specs seem to be for windows only. Has anyone used this product on mac?

I am not certain, but I believe there is a version of Dazzle for the Mac. However, it is not the route I would chose.
You really need a proper analogue to digital converter, like the ADVC110, to connect to your camera via the usual RCA cables, and to your Mac via firewire.

Has anyone used Malwarebytes or anything similar to protect Mac from virus etc

Has anyone used Malwarebytes or something similar to scan Mac for virus and other security and effiency problems?

I should have been more specific, I wasn't given a Mac to keep, I was given a Mac to clean up. I have almost 20 years experience working with personal computers and I've worked on every major OS that's been released during that time (OS/2, every version of Windows since 3.1, Linux, Mac OS, Unix). I no longer work in a shop specifically fixing computers but my family still gives me their computers to look at whenever they have issues. My cousin just gave me her laptop since she was unable to fill out any web forms that would try to verify her e-mail address, plus she kept getting pop ups to run some MacKeeper software. Had this been a computer I received second hand I would have re-installed the OS regardless of the state it was on, but since she needs the files on her computer for school I figured it'd be much easier to run a Mac OS equivalent of Malwarebytes than to backup everything and re-install the OS.
Unfortunately when you search the internet for a Malwarebytes alternative for Mac OS, the majority of the time you just get posts from people saying "Macs are super secure, don't worry about it you won't get infected", which is a completely useless response for someone whose computer is infected. The rest of the posts responding to people who ARE infected are much like your response "Just re-install the OS" but that doesn't address the underlying issue of what's infecting the computer for those people who can't afford to lose everything. I was eventually able to Google the symptoms of this issue and determine that it was a trojan known as DownLite or VSearch. Once I found where it was located I opened up a terminal, ran sudo su to elevate myself to root, deleted the VSearch folder and files from the terminal, ran ps ax | grep VSearch to find the running application and did a kill -9 [pid] to terminate the app (rather than rebooting.)
Once that was all done I was able to use Chrome and Safari without all of the popups and hijacks. It took all of 5 minutes once I knew what the underlying issue was but I was really hoping to find a program like Malwarebytes so I could just let it scan the computer and tell me "These applications are malicious..." especially since my cousin installed a lot of stuff I would consider junk on her laptop and I didn't want to delete things that are just harmless junk (since she might use them.) Since I ended up having to do this all manually I'm just hoping there's nothing else lingering on the computer that didn't have visible symptoms.

Has anyone used JAAS with WebLogic?

Has anyone used JAAS with Weblogic? I was looking at their example, and I have a bunch of questions about it. Here goes:
Basically the problem is this: the plug-in LoginModule model of JAAS used in WebLogic (with EJB Servers) seems to allow clients to falsely authenticate.
Let me give you a little background on what brought me to this. You can find the WebLogic JAAS example (to which I refer below) in the pdf: http://e-docs.bea.com/wls/docs61/pdf/security.pdf . (I believe you want pages 64-74) WebLogic, I believe goes about this all wrong. They allow the client to use their own LoginModules, as well as CallBackHandlers. This is dangerous, as it allows them to get a reference (in the module) to the LoginContext's Subject and authenticate themselves (i.e. associate a Principal with the subject). As we know from JAAS, the way AccessController checks permissions is by looking at the Principal in the Subject and seeing if that Principal is granted the permission in the "policy" file (or by checking with the Policy class). What it does NOT do, is see if that Subject
has the right to hold that Principal. Rather, it assumes the Subject is authenticated.
So a user who is allowed to use their own Module (as WebLogic's example shows) could do something like:
//THEIR LOGIN MODULE (SOME CODE CUT-OUT FOR BREVITY)
public class BasicModule implements LoginModule
private NameCallback strName;
private PasswordCallback strPass;
private CallbackHandler myCB;
private Subject subj;
         //INITIALIZE THIS MODULE
           public void initialize(Subject subject, CallbackHandler callbackHandler, Map sharedState, Map options)
                  try
                       //SET SUBJECT
                         subj = subject; //NOTE: THIS GIVES YOU REFERENCE
TO LOGIN CONTEXT'S SUBJECT
                                                 // AND ALLOWS YOU TO PASS
IT BACK TO THE LOGIN CONTEXT
                       //SET CALLBACKHANDLERS
                         strName = new NameCallback("Your Name: ");
                         strPass = new PasswordCallback("Password:", false);
                         Callback[] cb = { strName, strPass };
                       //HANDLE THE CALLBACKS
                         callbackHandler.handle(cb);
                  } catch (Exception e) { System.out.println(e); }
     //LOG THE USER IN
       public boolean login() throws LoginException
          //TEST TO SEE IF SUBJECT HOLDS ANYTHING YET
          System.out.println( "PRIOR TO AUTHENTICATION, SUBJECT HOLDS: " +
subj.getPrincipals().size() + " Principals");
          //SUBJECT AUTHENTICATED - BECAUSE SUBJECT NOW HOLDS THE PRINCIPAL
           MyPrincipal m = new MyPrincipal("Admin");
           subj.getPrincipals().add(m);
           return true;
         public boolean commit() throws LoginException
               return true;
    }(Sorry for all that code)
I tested the above code, and it fully associates the Subject (and its principal) with the LoginContext. So my question is, where in the process (and code) can we put the LoginContext and Modules so that a client cannot
do this? With the above example, there is no Security. (a call to: myLoginContext.getSubject().doAs(...) will work)
I think the key here is to understand JAAS's plug-in security model to mean:
(Below are my words)
The point of JAAS is to allow an application to use different ways of authenticating without changing the application's code, but NOT to allow the user to authenticate however they want.
In WebLogic's example, they unfortunately seem to have used the latter understanding, i.e. "allow the user to authenticate however they want."
That, as I think I've shown, is not security. So how do we solve this? We need to put JAAS on the server side (with no direct JAAS client-side), and that includes the LoginModules as well as LoginContext. So for an EJB Server this means that the same internal permission
checking code can be used regardless of whether a client connects through
RMI/RMI-IIOP/JEREMIE (etc). It does NOT mean that the client gets to choose
how they authenticate (except by choosing YOUR set ways).
Before we even deal with a serialized subject, we need to see how JAAS can
even be used on the back-end of an RMI (RMI-IIOP/JEREMIE) application.
I think what needs to be done, is the client needs to have the stubs for our
LoginModule, LoginContext, CallBackHandler, CallBacks. Then they can put
their info into those, and everything is handled server-side. So they may
not even need to send a Subject across anyways (but they may want to as
well).
Please let me know if anyone sees this problem too, or if I am just completely
off track with this one. I think figuring out how to do JAAS as though
everything were local, and then putting RMI (or whatever) on top is the
first thing to tackle.

Send this to:
newsgroups.bea.com / security-group.

Warning! Using SuperDuper to clone from an HDD to an SSD might seriously da

WARNING! USING SUPERDUPER TO CLONE FROM AN HDD TO AN SSD MIGHT SERIOUSLY DAMAGE THE HEALTH OF YOUR SSD!
This is the new thread which I referred to when replying to:
http://discussions.apple.com/thread.jspa?threadID=2274972&start=0&tstart=0
I used SuperDuper to clone from a VelociRaptor 300GB HDD to an OCZ Agility EX SLC SSD, with disastrous results.
To save me the time of rewriting all the events please refer to the following emails and online submissions:
(Biltan-Wales - 21 Dec 2009 - 11.02 GMT):-
After reading several very favourable product reviews of the above SSD, I have just purchased one from Aria Technology Ltd., to use as a boot drive for my (early 2009) 8-Core 2.93GHz Intel Xeon Nehalem desktop workstation.
Also, prior to purchase of an OCZ SSD, I posted a question on Apple's Discussions' Forum:
http://discussions.apple.com/thread.jspa?threadID=2263023&tstart=0
From the response to this, and from reading several other threads regarding SSDs, I found that several Mac Pro owners are using OCZ SSDs as boot drives, and in some cases employing up to 3 of them.
I received my Agility EX from Aria on 16th. December, and yesterday afternoon I decided to set up my boot drive and 4 drive RAID 0, as described in: http://discussions.apple.com/thread.jspa?threadID=2263023&tstart=0
First of all I used SuperDuper to clone from my VelociRaptor 300GB drive in Bay 1, to my original Apple (WD) 640GB drive in Bay 2.
Then I removed the original Apple drive, and installed it in an ONNTO dataTale TQ-M12H external single enclosure, using a Firewire 800 interface connection. Next I selected this as my boot drive to check it would boot OK, restarted my system, and there was no problem.
So my next step was to install the Agility EX, and another 3 VelociRaptor 300GB drives, in the Mac pro workstation.
First, I reselected VelociRaptor 1 as my boot drive, so that I could use SuperDuper to clone to the Agility EX.
The Agility EX was installed in the lower of the 2 optical bays, and was connected to the pre-wired SATA and power cable, and the VelociRaptors were placed in hard drive bays 2, 3, and 4.
I then started up the Mac Pro, and there were 4 message boxes on the desktop, requesting that the drives should be initialised. So then I used Disk Utility to initialise the 4 drives. The SSD was named "Agility EX Boot", and the others "VelociRaptor 2", VelociRaptor 3, and VelociRaptor 4". The Mac system accepted all 4, and mounted desk top icons for each drive. I cannot remember the exact figure, but the Agility EX was listed as approx. 64GB in Disk Utility after its initialisation. All 4 VelociRaptors are shown as 300.07GB. All drives were formatted as Mac OS Extended (Journaled).
The next stage was to use SuperDuper to clone from VelociRaptor 1 to the Agility EX Boot drive.
Everything was fine until 28.00GB had been copied, and then nothing more would copy. The total to be cloned was just under 30GB, which should not have been a problem with a SSD disk capacity of approx. 64GB, but everything was frozen at that point - exactly 28.00GB!
Eventually, my only option was to stop the process, and quit Super Duper.
Then I restarted the system to try again, but this is where there is a real problem now!
My system does not recognise the Agility EX at all now! Also, it is no longer listed in Disk Utility!
The system does not even acknowledge its existence! It is not even shown on the desktop at start-up, whereas I thought that perhaps there might have been another message box requesting that it should be reinitialised.
I tried disconnecting and reconnecting everything - all drives, interface connections, power cables etc., but to no avail!
This morning I tried this again, but still I cannot get my system to even acknowledge the Agility EX, let alone list it!
So at the moment I am still using VelociRaptor 1 as my boot drive, and, in fact, as my main drive, because I am reluctant to use it with the 3 other VelociRaptors as a 4 drive RAID 0 set up until I get this problem with the Agility EX resolved.
(OCZ - 22 Dec 2009 - 18.29 GMT):-
Cloning from a HDD to an SSD is very problematic. I strongly recommend against doing this. Instead you will want to just install normally onto the SSD. You can clone from SSD to SSD, or from HDD to HDD, but going from one to the other can cause issues.
Try disconnecting the drive from the computer for an hour or so. This will allow all power in the drive to fully discharge. This is a way of resetting the drive that can usually recover the drive. Then plug the drive back in. Does the drive show up again?
If so, delete the partition on the drive, then create a new partition and then install the OS onto it clean rather than clone the OS onto the drive. That should resolve the issues you are having.
(Biltan-Wales - 23 Dec 2009 - 16.19 GMT):-
Thank you for your advice.
I have now disconnected the Agility EX SSD, and removed it from my Mac Pro's lower optical bay.
As Christmas is imminent, and I will not be using my system very much over the next few days, I will leave the drive for 4 to 5 days to allow ample time for all the power to discharge.
Then I will reconnect it, and I will let you know whether or not the drive is recognised by my system.
I was not aware that cloning from a HDD to an SSD could be problematic. Several threads on the Apple Support Discussion Forum have recommended using SuperDuper or Carbon Copy Cloner for this purpose. SuperDuper is the preferred option of most Forum members, whereas Lloyd Chambers (diglloyd.com), author of "macperformanceguide.com", uses Carbon Copy Cloner to clone his HDD boot drives to his Intel and Crucial SSDs.
After the Agility EX had been set up as my system boot drive, my intention was to use SuperDuper to clone from it to my original Apple (WD) HDD, now in an external enclosure with Firewire 800 interface, and then use SuperDuper's Smart Update for regular backups, so that I always had an up to date spare boot drive for the OS and applications.
The current VelociRaptor 1 boot drive would then be erased, and I would then use the Mac OS Disk Utility to create a 4 drive software RAID ) with the other 3 VelociRaptors, and this would be backed up using Time Machine to my existing WD My Book Studio Edition II 2TB External Hard Drive.
Please correct me if I have misunderstood your advice, but are you saying that I should only use another SSD, and not my original Apple (WD) HDD, as my back-up external boot drive? I don't know of any other Mac users who are using SSDs for that purpose, possibly because of the prohibitive cost of doing so.
I am more than happy to follow your advice to reinstall the Mac OS and my applications cleanly onto the Agility EX, and, in fact, I did exactly that with my first VelociRaptor HDD, before I had SuperDuper. However, that would still leave me with the problem of how to set up and maintain an external back-up system boot drive, without incurring the expense of another SSD. Any suggestions please?
Anyway the most important matter is the existing problem, and I am hoping that following your advice will resolve this.
I will contact you again early next week. In the meantime have a very enjoyable Christmas!
(OCZ - 24 Dec 2009 - 00.25 GMT):-
If the image is of an HDD and that image is then cloned onto an SSD that does tend to be problematic. I do not recommend doing this, as an image of the HDD somewhat regularly does fail to copy onto an SSD and still remain functional or fast.
You can store the image file on any sort of drive. Storing the image file is fine, as that is just a digital file, so the storage medium doesn't matter. Its actually applying that image to a drive is where the problems often occur.
You can image from a HDD to a HDD just fine, or an SSD to an SSD just fine, but going from one to the other is problematic enough that I recommend not doing this. Sometimes it works just fine, but other times it can fail catastrophically to the point of even bricking the drive. To error on the side of caution I recommend just going a clean install on the new SSD.
Once you have that clean install done you can then take an image of that SSD and image on to other SSD's, or store the image on a HDD for backup purposes.
(Biltan-Wales - 29 Dec 2009 - 13.16 GMT)
Thank you for your last email.
Further to your previous email, and my reply of 23/12/2009. this morning I reconnected the Agility EX SSD.
However, unfortunately, the drive has not showed up again on my system. There is no icon for it on the desktop, nor is it listed in Disk utility.
When I checked Serial-ATAS in my Mac Pro's System Profiler, all 6 Intel ICH10 AHCI are listed in the Serial-ATA Device Tree, but, whereas all my other drives are sub-listed, there is nothing underneath the ICH10 AHCI for the lower optical bay.
As the drive has had 6 days to discharge and reset, it would appear that it has not recovered.
Where do I go from here?
I am still awaiting a reply from OCZ, but that is not surprising, because of the different time zones and the Christmas?New Year holiday period.
In the meantime does anybody else have any ideas, please?

Hi thanon,
"So the SSD is not visible, not even in disk utility, even after a restart ?":-
No.
"Check the log of SuperDuper (Window-Show Log); warnings are in red, I think.":-
This is a copy of the log, but it only refers to the original Mac (WD) drive as the Target Volume and it only lists the last Smart Update. There is no record of the original cloning to the same drive on 21st. December, nor of the interim Smart Updates. There is no record logged at all for the OCZ Agility EX SSD, despite the unsuccessful cloning attempt on 21st. December:-
| 11:39:15 AM | Info | SuperDuper!, 2.6.2 (87), path: /Applications/SuperDuper!.app, Mac OS 10.6.2 build 10C540 (i386)
| 11:39:15 AM | Info | Started on Sun, Dec 27, 2009 at 11:39 AM
| 11:39:15 AM | Info | Source Volume: VelociRaptor 1, mount: /, device: /dev/disk3s2, media: WDC WD3000HLFS-01G6U1, interconnect: Internal SATA, file system: "Journaled HFS+", OS: 10.6.2 (10C540), capacity: 299.73 GB, used: 30.53 GB, directories: 164608, files: 521266, ejectable: NO, ACLs: Enabled
| 11:39:15 AM | Info | Target Volume: Untitled 1, mount: /Volumes/Untitled 1, device: /dev/disk5s2, media: Ext Hard Disk, interconnect: External FireWire, file system: "Journaled HFS+", OS: 10.6.2 (10C540), capacity: 639.79 GB, used: 30.27 GB, directories: 164519, files: 522654, ejectable: YES, ACLs: Enabled
| 11:39:15 AM | Info | Copy Mode : Smart Update
| 11:39:15 AM | Info | Copy Script : Backup - all files.dset
| 11:39:15 AM | Info | Transcript : BuildTranscript.plist
| 11:39:15 AM | Info | PHASE: 1. Prepare to Copy Files
| 11:39:15 AM | Info | ...ACTION: Preparing VelociRaptor 1
| 11:39:15 AM | Info | ......COMMAND => Verifying the integrity of volinfo.database
| 11:39:15 AM | Info | volinfo.database OK
| 11:39:15 AM | Info | ......COMMAND => Enabling permissions on VelociRaptor 1
| 11:39:15 AM | Info | Refreshing Disk Arbitration ...
| 11:39:15 AM | Info | ......COMMAND => Verifying that permissions are enabled for VelociRaptor 1
| 11:39:15 AM | Info | Permissions on '/' are enabled.
| 11:39:15 AM | Info | ...ACTION: Preparing Untitled 1
| 11:39:15 AM | Info | ......COMMAND => Enabling permissions on Untitled 1
| 11:39:15 AM | Info | Refreshing Disk Arbitration ...
| 11:39:16 AM | Info | ......COMMAND => Verifying that permissions are enabled for Untitled 1
| 11:39:16 AM | Info | Permissions on '/Volumes/Untitled 1' are enabled.
| 11:39:16 AM | Info | ......COMMAND => Verifying that Untitled 1 ACL support matches VelociRaptor 1
| 11:39:16 AM | Info | ...ACTION: Preserving Spotlight state on Untitled 1
| 11:39:16 AM | Info | ......COMMAND => Disabling Spotlight search indexing on Untitled 1
| 11:39:16 AM | Info | PHASE: 2. Copy Files
| 11:39:16 AM | Info | ...ACTION: Copying files from VelociRaptor 1 to Untitled 1 using Smart Update
| 11:39:16 AM | Info | ......COMMAND => Cloning VelociRaptor 1 to Untitled 1
| 11:39:16 AM | Info | Copying copy files with delete using script: /Users/williamtanner/Library/Application Support/SuperDuper!/Copy Scripts/Standard Scripts/Backup - all files.dset
| 11:39:16 AM | Info | Loading 27 commands from copy script /Applications/SuperDuper!.app/Contents/Resources/Copy Scripts/Exclude system temporary files.dset
| 11:39:16 AM | Info | Loading 6 commands from copy script /Applications/SuperDuper!.app/Contents/Resources/Copy Scripts/Exclude system cache files.dset
| 11:39:16 AM | Info | Loading 1 commands from copy script /Applications/SuperDuper!.app/Contents/Resources/Copy Scripts/Exclude Norton FileSaver files.dset
| 11:39:16 AM | Info | Loading 2 commands from copy script /Applications/SuperDuper!.app/Contents/Resources/Copy Scripts/Exclude Google Desktop Index files.dset
| 11:39:16 AM | Info | Loading 1 commands from copy script /Applications/SuperDuper!.app/Contents/Resources/Copy Scripts/Exclude iTunes Temporary files.dset
| 11:39:16 AM | Info | Loading 0 commands from copy script /Users/williamtanner/Library/Application Support/SuperDuper!/Copy Scripts/Standard Scripts/Backup - all files.dset
| 11:39:20 AM | Info | /
| 11:39:20 AM | Info | /.vol
| 11:39:20 AM | Info | Ignoring /.vol
| 11:39:20 AM | Info | /cores
| 11:39:20 AM | Info | /Network
| 11:39:20 AM | Info | /.Spotlight-V100
| 11:39:20 AM | Info | Preserving /.Spotlight-V100
| 11:39:20 AM | Info | /private
| 11:39:20 AM | Info | Ignoring /private/var/folders/-S
| 11:39:20 AM | Info | Ignoring /private/var/folders/zz
| 11:39:20 AM | Info | Ignoring /private/var/tmp/com.epson.epw
| 11:39:20 AM | Info | Ignoring /private/var/tmp/com.apple.speech.synthesis.globals
| 11:39:20 AM | Info | Ignoring /private/var/tmp/launchd
| 11:39:20 AM | Info | Ignoring /private/var/tmp/com.WD.WDDriveManagerService
| 11:39:23 AM | Info | Ignoring /private/var/vm/swapfile0
| 11:39:23 AM | Info | Ignoring /private/var/run/vpncontrol.sock
| 11:39:23 AM | Info | Ignoring /private/var/run/usbmuxd
| 11:39:23 AM | Info | Ignoring /private/var/run/syslog.pid
| 11:39:23 AM | Info | Ignoring /private/var/run/syslog
| 11:39:23 AM | Info | Ignoring /private/var/run/printtool
| 11:39:23 AM | Info | Ignoring /private/var/run/portmap.socket
| 11:39:23 AM | Info | Ignoring /private/var/run/mDNSResponder
| 11:39:23 AM | Info | Ignoring /private/var/run/cupsd
| 11:39:23 AM | Info | Ignoring /private/var/run/com.apple.ActivityMonitor.socket
| 11:39:23 AM | Info | Ignoring /private/var/run/asl_input
| 11:39:23 AM | Info | Ignoring /private/var/run/SCHelper
| 11:39:23 AM | Info | Ignoring /private/var/run/diskarbitrationd.pid
| 11:39:23 AM | Info | Ignoring /private/var/run/configd.pid
| 11:39:23 AM | Info | Ignoring /private/var/run/DirectoryService.pid
| 11:39:23 AM | Info | Ignoring /private/var/run/.DSRunningSP1
| 11:39:23 AM | Info | Ignoring /private/var/run/automount.initialized
| 11:39:23 AM | Info | Ignoring /private/var/run/mds.pid
| 11:39:23 AM | Info | Ignoring /private/var/run/com.apple.loginwindow.didRunThisBoot
| 11:39:23 AM | Info | Ignoring /private/var/run/pppconfd
| 11:39:23 AM | Info | Ignoring /private/var/run/resolv.conf
| 11:39:23 AM | Info | Ignoring /private/var/run/sntp.log
| 11:39:23 AM | Info | Ignoring /private/var/run/ntpd.pid
| 11:39:23 AM | Info | Ignoring /private/var/run/utmpx
| 11:39:23 AM | Info | Ignoring /private/var/run/mds
| 11:39:32 AM | Info | Ignoring /private/var/db/BootCache.playlist
| 11:39:32 AM | Info | Ignoring /private/var/db/volinfo.database
| 11:39:32 AM | Info | Ignoring /private/tmp/MobileDevice.log
| 11:39:32 AM | Info | Ignoring /private/tmp/launchd-99.KTlnYd
| 11:39:32 AM | Info | Ignoring /private/tmp/launch-TIwnDn
| 11:39:32 AM | Info | Ignoring /private/tmp/launch-S6asBo
| 11:39:32 AM | Info | Ignoring /private/tmp/launch-1v6MDi
| 11:39:32 AM | Info | Ignoring /private/tmp/icssuis501
| 11:39:32 AM | Info | Ignoring /private/tmp/4b3745a3d4d81
| 11:39:32 AM | Info | Ignoring /private/tmp/target221.indexState
| 11:39:32 AM | Info | /Users
| 11:39:36 AM | Info | Ignoring /.hotfiles.btree
| 11:39:36 AM | Info | /bin
| 11:39:36 AM | Info | /sbin
| 11:39:36 AM | Info | /usr
| 11:39:48 AM | Info | /System
| 11:41:47 AM | Info | /Library
| 11:42:41 AM | Info | /Applications
| 11:44:22 AM | Info | /.Trashes
| 11:44:22 AM | Info | /.fseventsd
| 11:44:22 AM | Info | Preserving /.fseventsd
| 11:44:22 AM | Info | /dev
| 11:44:22 AM | Info | /net
| 11:44:22 AM | Info | /home
| 11:44:22 AM | Info | /Volumes
| 11:44:22 AM | Info | Ignoring /Volumes/My Book
| 11:44:22 AM | Info | Ignoring /Volumes/VelociRaptor 3
| 11:44:22 AM | Info | Ignoring /Volumes/VelociRaptor 4
| 11:44:22 AM | Info | Ignoring /Volumes/VelociRaptor 2
| 11:44:22 AM | Info | Ignoring /Volumes/VelociRaptor 1
| 11:44:22 AM | Info | Ignoring /Volumes/Untitled 1
| 11:44:22 AM | Info | Evaluated 685438 items occupying 29.45 GB (164606 directories, 511269 files, 9563 symlinks)
| 11:44:22 AM | Info | Copied 463 items totaling 0.69 GB (117 directories, 335 files, 11 symlinks)
| 11:44:22 AM | Info | Cloned 29.15 GB of data in 306 seconds at an effective transfer rate of 95.25 MB/s
| 11:44:22 AM | Info | ......COMMAND => Resetting Custom Icon bit on Untitled 1
| 11:44:22 AM | Info | PHASE: 3. After Successful Copy
| 11:44:22 AM | Info | ...ACTION: Making Untitled 1 bootable
| 11:44:22 AM | Info | ......COMMAND => Blessing OS X System Folder
| 11:44:23 AM | Info | Successfully blessed Mac OS X folder on Untitled 1
| 11:44:23 AM | Info | ......COMMAND => Blessing OS 9 System Folder
| 11:44:23 AM | Info | Did not bless Mac OS 9 System Folder on Untitled 1 because it does not exist.
| 11:44:23 AM | Info | ...ACTION: Updating prebinding on Untitled 1
| 11:44:23 AM | Info | ......COMMAND => Updating boot cache on '/Volumes/Untitled 1'
| 11:44:30 AM | Info | updatedyld_sharedcache[271] current i386 cache file invalid because /System/Library/PrivateFrameworks/DesktopServicesPriv.framework/Versions/A/Desk topServicesPriv has changed
| 11:44:34 AM | Info | updatedyld_sharedcache: warning mismatched install path in /System/Library/CoreServices/RawCamera.bundle/Contents/Resources/MetadataLib.dy lib for /usr/lib/libgcc_s.1.dylib
| 11:44:34 AM | Info | updatedyld_sharedcache: warning mismatched install path in /System/Library/CoreServices/RawCamera.bundle/Contents/MacOS/RawCamera for /usr/lib/libgcc_s.1.dylib
| 11:44:38 AM | Info | updatedyld_sharedcache[271] current ppc cache file invalid because /System/Library/PrivateFrameworks/DesktopServicesPriv.framework/Versions/A/Desk topServicesPriv has changed
| 11:44:41 AM | Info | updatedyld_sharedcache: warning mismatched install path in /System/Library/CoreServices/RawCamera.bundle/Contents/Resources/MetadataLib.dy lib for /usr/lib/libgcc_s.1.dylib
| 11:44:41 AM | Info | updatedyld_sharedcache: warning mismatched install path in /System/Library/CoreServices/RawCamera.bundle/Contents/MacOS/RawCamera for /usr/lib/libgcc_s.1.dylib
| 11:44:45 AM | Info | updatedyld_sharedcache[271] current x86_64 cache file invalid because /System/Library/PrivateFrameworks/DesktopServicesPriv.framework/Versions/A/Desk topServicesPriv has changed
| 11:44:48 AM | Info | updatedyld_sharedcache: warning mismatched install path in /System/Library/CoreServices/RawCamera.bundle/Contents/MacOS/RawCamera for /usr/lib/libgcc_s.1.dylib
| 11:44:48 AM | Info | updatedyld_sharedcache: warning mismatched install path in /System/Library/CoreServices/RawCamera.bundle/Contents/Resources/MetadataLib.dy lib for /usr/lib/libgcc_s.1.dylib
| 11:44:52 AM | Info | Successfully updated boot cache on Untitled 1
| 11:44:52 AM | Info | ...ACTION: Restoring Spotlight state on Untitled 1
| 11:44:52 AM | Info | ......COMMAND => Restoring Spotlight search indexing state on Untitled 1
| 11:44:53 AM | Info | /Volumes/Untitled 1:
| 11:44:53 AM | Info | Indexing enabled.
| 11:44:53 AM | Info | Indexing enabled on Untitled 1
| 11:44:53 AM | Info | Copy complete.
"Maybe turn the MP off, pull the power cord and disconnect all external devices but keyboard and mouse, disconnct the SSD, reconnect and start MP":-
I have tried this several times without any success.
"Also, make sure no programs are running during cloning, and leave the computer alone.":-
SuperDuper was the only program running when I cloned firstly to the Mac (WD) HDD, and secondly to the Agility EX on 21st. December.
Also everything was disconnected before I removed and transferred the Mac HDD to an external enclosure.
After I had checked that the Mac HDD had been cloned successfully, everything was disconnected again before I fitted the Agility Ex and the other 3 VelociRaptors in the lower optical drive bay, and drive bays 2,3 & 4 respectively.
I used a Lindy anti-static Service Kit throughout the whole process. I purchased this originally for when I installed 16GB of Kingston RAM, an ATI Radeon HD4870, and my first VelociRaptor

Has anyone used the QuickUSB module (Bitswise Systems) to interface to a USB Camera via IMAQ for USB?

Has anyone used the QuickUSB module made by Bitwise Systems with LabVIEW for image acquisition. I have a USB camera and I'm trying to use the IMAQ for USB controls to no avail. Any input is appreciated.

Are you using the NI-IMAQ for USB functions or are you calling the QuickUSB libraries from LabVIEW? Unless the USB camera is DirectShow compliant, then it will not work with the NI-IMAQ for USB driver. You can use the Code Interface Node in LabVIEW to call external dll's, and it looks like from QuickUSB's website that is the best way to go. Hope this helps.
Jason N

Has anyone used Thunderbolt or USB 3.0?

In the not too distant future I am intending to upgrade from my 2008 24" 2.8GHz iMac.
The new models appear to have gone down the Thunderbolt route which appears to be not very popular with HDs being few and far between and very expensive.
USB 3.0 whilst theoretically only half the speed seems to be taking off and reasonably cheap, and appears to be more universally adopted.
Could Apple have backed the wrong horse on this occasion?
Sorry, I was just thinking aloud, definitely not speculating.
So has anyone used Thunderbolt and got anything good or bad to say about it?

Not personally:
The german computer-magazine c't tested the Promise Pegasus R6 Thunderbolt and found it speedwise way ahead of USB 3.0 and eSATA.
As a RAID-Level 0 with 6 x Hitachi HDS721010CLA332 (7.200 U/min, 1TB each) and MBP 13" 2011 OSX 10.6.8:
Write - 693 MByte/s
Read - 721 MByte/s
Read AND Write - 323 MByte/s
Time Machine -capable and OS X Bootable.
0.8 Sone when active
61.6 W active - 48 W when not used.
Sadly the article is not avaibale other than Printed.
Stefan

I just saw a message that iWeb has been discontinued by Apple. It suggested EverWeb. Has anyone used this or do you have aother recommendation?

I just saw a message that iWeb has been discontinued by Apple. It suggested changing to EverWeb. Has anyone used this or do you have another recommendation?

Hi
I have now used Everweb to transfer a website from iWeb & am now working on transferring a second website.
I cannot recommend Everweb highly enough. I am an amateur, so iWeb was the easy option for me. Everweb is just as easy to use and very similar to iWeb. New features are being added every few days.
I am extremely impressed by the excellent and prompt service from both the forum and support. All my questions have been answered (& there have been many of them!)
Everweb is complimented by an excellent site Everweb codebox which has developed more widgets and codes to add to Everweb. Roddy from Everweb codebox has been invaluable by answering questions on the forum & generally complimenting the Everweb team.
I have purchased the Everweb program & Hosting. This gives my 1 click updating and works seamlessly. The price is competitive and the support exemplary.
All in all, I am delighted with Everweb, excellent program & excellent support!! I would not hesitate in recommending it to anyone.
In answer to your question...buy it!!!!
Lynn

Has anyone used "Microsoft.BizTalk.B2B.PartnerManagement" API ?

Hello, forum; trying to make sense of that undocumented API library to create an agreement using BizTalk 2010. So far, I can create a Partner, Business Profiles, Business Identities and Partnerships, but how to create an agreement (onewayagreements and all
that) still eludes me. I have checked one reference, it was written by Mick Breeze (http://blogs.breeze.net/mickb/2012/05/22/BizTalk2010CreatingTPMPartnersThroughCode.aspx),
and also getting inspired by the newest published in here (http://msdn.microsoft.com/en-us/library/windowsazure/dn232396.aspx) which is not the same but at least it's something.
I have navigated through the classes but I can't manage to do all the tasks that it is suppose to achieve.
Has anyone used this before that may be able to help ? Is there any SDK sample of some sort ?
Thanks in advance.

Partner automation. The user wants to use an asp.net form instead of using biztalk admin console, in order to create and update a large party database, the total count rounding between 300 to 500 partners, so, we have already a webform with all business
related information and we've add some port related information that will ultimately end up as the party information. With that info, this library should be able to accomplish everything we normally do from the console.
We are not migrating from a previous version, so the party migration tools is a no-go. We explored the idea of creating a binding-like file that would be loaded from BtsTask, but ultimately, we end up with the idea of using this obscure library to perform
all those so called duties of handling party related information on biztalk server.
Thanks in advance.

Has anyone used the appscript modual for python rather than streight AS?

I just discovered appscript and so far I like what I see. has anyone used it?
Does it just wrap around actual applescript commands which it then sends to osascript with a system call or does it use the message system directly? Is there anything that it has not yet implemented that might cause problems?
To me it seems to be a perfect solution to the clutter that AS seems to be... at least from someone coming from more traditional languages.

In startMovie, you need to register the xtra
on startMovie
axRegister(serial code here)
end
Then, on your Record Button, something like this:
on mouseUp me
--start recording session - using 400k as maximum here
errOpen=axOpenRecorder(400000)
--see if there is an error
put errOpen
--save the new audio as a file
errRecord=axRecordSoundToFile("soundName","c:\path\to\soundfile.wav")
--see if there is an error
put errRecord
end
then make sure you close the recorder in stopMovie
on stopMovie
axCloseRecorder()
end
You can also make a Stop Recording button that has code like
this:
on mouseUp me
errStop=axStopRecording()
put errStop
end

Re: Interfaces in Forte - has anyone used them?

We are making use of interfaces extensively and have never had the
slightest problem. Interfaces do not cause any overhead, since they are
mainly a means to support type checking by the compiler. At run-time the
interface does not appear any more.
Using Forte 3.0.F.2
General wrote:
>
We are embarking on the analysis phase of a large pay/personnel project. =
We have been advised to use interfaces wherever possible, because they =
promote flexibility and reusability. I am fairly well convinced of the =
benefits of using interfaces - they appear to have a lot of advantages, =
and no drawbacks. However, I do wonder whether Forte's implementation of =
interfaces is stable and usable (..it was only introduced in version 3). =
If not, we may be better advised to use standard techniques.
If you have used Forte interfaces I would be interested to hear how you =
got on.
regards,
Tim Kimber--
Dr. Thomas Kunst mailto:[email protected]
sd&m GmbH & Co. KG http://www.sdm.de
software design & management
Thomas-Dehler-Str. 27, 81737 Muenchen, Germany
Tel +49 89 63812-221 Fax -444
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

Eric,
You are correct, "manipulate anAIFace object" is not really the correct
way of thinking about what is happening. We are really manipulating an
instance of an object through an interface.
In regards to your other statement: "if Project C needs visibility to B,
it must have B as a supplier Plan." Forte does not force this to happen
when you are using interfaces, which is what causes the problem. Let me
expand on my initial example and add enough detail so that you can create
the problem, which surfaces as a deserialization error:
Project A (No Supplier Plans)
Defines Interfaces: UnitIFace with method GetValue() which returns an
integer
Project B (Contains A as a Supplier Plan)
Defines Class: Unit with attribute _Value as an integer and method
GetValue() which returns _Value. Implements interface UnitIFace.
Project C (Contains A as a Supplier Plan)
Defines Class: Square with method Calculate which accepts an
UnitIFace as an input parameter and returns an integer. This class needs
to be setup as a distributed object so that I service object can be
defined using this class.
Defines Service Object: SqaureSO using the Square class.
Project D (Contains B and C as Supplier Plans)
Defines a class or uses a window that creates an instance of Class B
and passes it to the SquareSO service object that sqaures the value and
returns an integer.
Once this is setup, use the running man to run everything locally. This
will run fine because the dependencies for the local partition end up
including Projects A, B, C and D. Next, run distributed and move the SO
to a remote partition. Now when you execute you will receive a
deserialization error. This happens because the dependencies for the
remote partition only included project A and C. The partition did not
have the necessary information to deserialize the underlying instance of
Class Unit that is referenced through the inteface UnitIFace.
The problem can be resolved by either adding Project B as a supplier plan
to Project C or ensuring that the interface and class are declared in the
same project as I suggested in my previous message. In either case, this
must be resolved by the programmer since Forte is not yet smart enough to
correctly resolve the project dependencies, even though all of the
information needed to establish the correct dependency hierarchy is
available.
Bradley K Wells
[email protected]
Strong Capital Management, Inc
http://www.strong-funds.com/
From: Eric Pereira
Sent: Friday, July 31, 1998 5:57 PM
To: [email protected]
Cc: [email protected]
Subject: RE: Interfaces in Forte - has anyone used them?
Bradley,
Thanks for that descriptive note on interfaces.
I do have a observation : in that example you gave us, if Project C
needs visibility to B, it must have B as a supplier Plan. Therefore, I
don't quite understand how partioning classes in C would end up with a
run-time errror in distributed mode, given that B supplies C (something
you've perhaps missed out in your example ?).
Also, is it really possible to "manipulate AIFace objects" ? Interfaces
are'nt really objects, they just help implement a compile-time type
check.
Thanks.
Eric Pereira
Forte Consultant
----<snip>------------------
Example:
Project A - Contains AIFace
Project B - Contains Class B which implements AIFace, depends on Project
A
Project C - Contains Classes manipulating AIFace objects, depends on
Project A
This can run fine locally since the local partition has knowledge of all
the classes in A, B, and C. Now as soon as you throw a service object
on
classes on Project C and push them into a remote partition, your
application starts failing because that partition does not contain the
information form project B since there is no dependency on that project.
The partition needs the information from project B though since it
contains the definitions for the actual implementation objects, however
there was no way for Forte to determine that need when it generated the
partition.
This problem is initially eliminated by keeping the interfaces in the
same project as the underlying business objects. But once you start to
have interfaces implemented by multiple classes from multiple projects,
then this won't cover all the bases either. In any case, it is an issue
that you will need to consider at some level when using interfaces.
Good luck!
Bradley K Wells
[email protected]
Strong Capital Management, Inc
http://www.strong-funds.com/
From: "Ngai, Stuart" <[email protected]>
Date: Thu, 30 Jul 1998 11:10:50 -0400
Subject: RE: Interfaces in Forte - has anyone used them?
With version 3G, you can not create an array of interfaces. I believe
Forte
will have that feature in version 4 (which is scheduled to be in
production
at the end of next year).
-----Original Message-----
From: Thomas Kunst [SMTP:[email protected]]
Sent: Thursday, July 30, 1998 8:52 AM
To: [email protected]
Cc: General
Subject: Re: Interfaces in Forte - has anyone used them?
We are making use of interfaces extensively and have never had the
slightest problem. Interfaces do not cause any overhead, since theyare
mainly a means to support type checking by the compiler. At run-timethe
interface does not appear any more.
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
Get Your Private, Free Email at http://www.hotmail.com
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

Has anyone used the new 5K retina iMac with Lightroom

Has anyone used Lightroom with the new 5K Imac. If so any problems ?

Just bought one - arrives next week. From what i can tell it's should be the fastest mac for lightroom. Processor speed is most vital. Doesn't really use all the mac pro multiple cores as I understand 4 is plenty (correct me pls?) and 16Gb ram should hopefully do it. Getting a raid thunderbolt 2 drive for image storage which will daisy chain with my eizo monitor. Choose 3tb internal fusion as I understand full SSD doesn't really help too much. 2GB graphics plenty unless you're doing video maybe?.
Only issue is I have a series of archive 3TB firewire 800 drives which are daisy chained. the questions is how will these work with an adapter but this remains to be seen....

Has anyone used SuperDuper to go from C2D to SR?

Similar Messages

Maybe you are looking for