Has somebody already tried HTBase - Essbase Hot Backup Tool?

Dear all,
You guys know this tool (HTBase - Essbase Hot Backup)?
Is it neccesary to enable transaction loggin from essbase.cfg to make it work?.
I look fordward to your responses. Regards.

I saw a demo of it by Bruno and it works. They have a fewer other products in the pipeline. I am almost certain you did not need to enable transactional logging as we debated the benefit of the tool if transactional logging was enabled and regulary data exports were performed. I do not know of anyone using at the moment.
Thanks,
Nathan

Similar Messages

  • Has somebody already used Applicom PCI2000ETH Card or Applicom SW1000ETH software to communicat​e with ETHERNET bewteen siemens s7-300 and LabVIEW DSC ?

    I want to use ETHERNET and not PROFIBUS to communicate and I think you can do that with only the applicom software SW-1000ETH. You must just have an ethernet card on your PC. So, you could use a notebook with an
    ethernet card. You can also use Applicom PCI2000ETH for better performance.

    Hi,
    You might be able to get the configuration listed above working as long as you can get from Siemens/Applicom or any other third party provider a OPC Server that communicates with the S7-300. Since LabVIEW DSC is a OPC client, you would be able to establish connection.
    The National Instruments driver for the S7-300 (Containnned in the product called "IA OPC Server CD") does not support communication through ethernet directly, you would either have to have a Profibus board or use a serial port with a Siemens HMI Adapter.
    I hope it helps
    Best Regards
    Andre Oliveira

  • Environment configuration for Hot Backups

    Hi all,
    1. I am trying to create a hot backup tool based on the read-only Environment strategy ([discussed in a previous thread|http://forums.oracle.com/forums/message.jspa?messageID=3674008#3674008] ).
    Now, leaving aside the EnvironmentConfig.setReadOnly(true), I have found quite a few possible other configuration options in the EnvironmentParams class and I'm wondering if there are some that I should be using.
    Here are a couple of examples:
    - ENV_RECOVERY
    - ENV_RUN_INCOMPRESSOR
    - ENV_RUN_CHECKPOINTER
    - ENV_RUN_CLEANER
    Would it make sense to configure any of these?
    2. After creating a hot backup I have tried to test its state. Basically, the approach was quite simple:
    - open a read-only env on the backup
    - try to access the databases in the env
    My idea is that if the above 2 ops are succeeding then there is a very good chance that the backup is correct.
    Now, while playing with the above configuration options I have noticed that if I'm setting ENV_RECOVERY to false in this test environment, then any attempt to access the databases within results in a DatabaseNotFoundException.
    Can someone help me understand what is happening? (basically, I cannot make a connection between recovery and access to the DBs in the environment)
    Many thanks in advance,
    ./alex
    PS: I've forgot to mention that I'm running a quite old version: 2.1.30
    Edited by: Alex Popescu on Aug 13, 2009 5:50 AM

    ENV_RECOVERY - suppresses running recovery at Environment creation. Internal parameter.
    ENV_RUN_INCOMPRESSOR, ENV_RUN_CHECKPOINTER, ENV_RUN_CLEANER - disable the INCompressor, Checkpointer, and Cleaner Daemon threads.
    You should not need to adjust any of these parameters for your DbBackup utility. In fact, ENV_RECOVERY is an "internal use only" parameter.
    PS: I've forgot to mention that I'm running a quite old version: 2.1.30
    I'm sorry to be the bearer of bad news, but as my colleague Mark Hayes stressed in a previous post, you really need to upgrade from 2.1.30 to 3.3.latest. It is highly probable that you will eventually run into bugs with 2.x and we are unlikely to (1) be willing to diagnose them, and (2) fix them. As Mark pointed out, 2.1 is 3.5 years old and the product has had a lot of improvements in that time. We are happy to answer questions on this forum relating to the latest major release, but dealing with old and crusty code is certainly going to be well below our allowable priority level.
    Charles Lamb

  • BR0372E File /oracle/ SID /sapreorg/space SID .log has been already reporte

    Hello,
    The backup offline failed, i get the error as bellow:
    #SAVED.... 20111009.0135.10                                                                          
    BR0372E File /oracle/<SID>/sapreorg/space<SID>.log has been already reported by backup utility           
    BR0280I BRBACKUP time stamp: 2011-10-10 00.19.19                                                     
    #PFLOG.... /oracle/<SID>/sapbackup/begypbev.aff                                                        
    #SAVED.... 20111009.0135.12                                                                          
    BR0280I BRBACKUP time stamp: 2011-10-10 00.19.22                                                     
    #PFLOG.... /oracle/<SID>/sapbackup/back<SID>.log                                                         
    #SAVED.... 20111009.0135.13                                                                          
    BR0280I BRBACKUP time stamp: 2011-10-10 00.21.07                                                     
    #PFLOG.... /oracle/<SID>/102_64/dbs/init<SID>.ora                                                        
    #SAVED.... 20111009.0135.08                                                                          
    [Normal] From: OB2BAR_BACKINT@e108pae0 "<SID>"  Time: 10/10/11 00:21:07                                
    #Backint exits with the code (0).                                                                    
    BR0232E 5 of 6 files saved by backup utility                                                         
    BR0280I BRBACKUP time stamp: 2011-10-10 00.21.07                                                     
    BR0231E Backup utility call failed                                                                   
    BR0056I End of database backup: begypbev.aff 2011-10-10 00.21.07                                     
    BR0280I BRBACKUP time stamp: 2011-10-10 00.21.08                                                     
    BR0054I BRBACKUP terminated with errors
    could you please help me
    thx in advance

    Hi,
    Please note that in fact the error BR0372E File ... has been already reported as saved by backup utility is not an error issued by brbackup tool but by the backint which is third party tool.
    As the backint is a third party tool, you will need to contact your Netbackup partner to assist with solution.
    Regards,
    Abhishek

  • Failure when trying to open db with resetlogs after restore of hot backup

    Hello,
    i know that ora-600 errors should be directed to oracle instead of here, but as i have no access to oracle support you may be able / willing to give me some hint anyway. here is what i tried to do:
    1. Make a Hot Backup of an Oracle DB running on Win2003, Version 9.2.0.5
    2. Trying to restore this backup on a new host, running WinXP, Oracle 9.2.0.5
    I can create the new controlfile and do a recovery with the syntax
    "recover database using backup controlfile until cancel"
    However, after this i'm trying to open the DB with the following syntax:
    "alter database open resetlogs"
    This takes a few seconds, then the instance gets terminated, showing an ora-600 error in the alert.log (i guess its useless to show the specific ora-600 error here, or am i wrong at this point?)
    now i'm wondering if the difference in the operating system could be the reason ? I also have to mention that the database files from the hot backup were transfered over a WAN line, could a damage to this files, happened during the transfer cause something like this ?

    These are from Howard
    When you re-create a controlfile using a script or command that says 'create controlfile...', that command will require you to spell out the path to all the datafiles and online redo logs. It is a simple matter for your server process to visit each of the files mentioned in the create controlfile and read the SCN stored in the datafile header. It can also read the online redo logs and read the latest checkpoint change number stored there.
    If all those numbers agree, that is obviously the age to which the rest of the database had gotten before the controlfiles were lost, and it's OK to create the new controlfile with that agreed-upon SCN forced in to the controlfile as its new SCN. Therefore the entire database is consistent and the database can be opened without recovery.
    This sort of thing is what happens when you close your database down nicely and then delete all controlfiles as part of a recovery demo on a training course!
    If those numbers don't agree, then it doesn't really matter. Logically, the highest number found, whether that be in one or more of the datafiles or one of the online logs, must be the age the database had reached before disaster struck. Your server process then writes that highest number into the new controlfile as its new SCN, and therefore your new controlfile agrees with the age of the latest bit of your database. The bits which were found to have smaller SCNs than that are therefore obviously in need of recovery -and because your new controlfile knows the SCN at which recovery should stop, recovery can be performed without trouble.
    When the datafiles are inconsistent the control file has the latest SCN on it and it tries to bring the entrire database consisent with respective to its SCN..if something does not matches it says it is consisten
    SO the recovery is done mainly based on the Controlf file..but the term backup..assume we have binary backup or the created new controlfile will have the scn to bring the DB to consistent state
    Message was edited by:
    Maran Viswarayar

  • My Adobe has stopped allowing me to move library books from my PC to my KOBO (both show authorized on the ADE. the message reads : CE_COPY_NOT_ALLOWED - No permission to copy book.  It used to work. Any easy fixed for me?(I already tried uninstall and re-

    My Adobe has stopped allowing me to move library books from my PC to my KOBO (both show authorized on the ADE. the message reads : CE_COPY_NOT_ALLOWED - No permission to copy book.  It used to work. Any easy fixed for me?(I already tried uninstall and re-install)

    Welcome to the Club! Got the same Problem and had a really hard time reaching the Customer Support because they were down due to maitenance! Just wrote to their experts chat and hope to get an answer in this life!
    I tried to authorize my Computer and eBookreader with a new Adobe-ID, but it says I've done used this ID too often, even though it was brandnew! Can't copy my just-purchased eBook because "Copying is not allowed".
    I hold my thumbs for you that Adobe solves this Problem fast enough. Other ways I'll sell my eBookreader and buy the Kindle-Reader from Amazon and say GOOD BYE to Adobe!

  • My daughter's iPhone 3gs has just been replaced by Apple. When she tried to restore her backup files she was told to upgrade to itunes 10, but she can't because her Macbook is too old to run it. What do we need to do?

    My daughter's iPhone 3gs has just been replaced by Apple. When she tried to restore her backup files she was told to upgrade to itunes 10, but she can't because her Macbook is too old to run it. What do we need to do to get all her stuff onto the new phone?

    Here's what I'd do, go back to the Apple store, take the phone & computer. Ask the geniuses how to fix this since they replaced the phone. You never know, they may just update the computer for free...its happened before...can't gurantee it will happen for you, but worth a try.
    Otherwise, you're looking at purchasing a retail copy of Leopard, however if her computer can handle Snow Leopard you can purchase the $29 upgrade disk & install a full copy of SL.

  • Upgrading to V4 has lost all of my Bookmarks, I still have the restore files in my profile data but they will not load, I have tried importing the html backup file too but it didn't work either. How can I get them back?

    Upgrading to V4 has lost all of my Bookmarks, I still have the restore files in my profile data but they will not load, I have tried importing the html backup file too but it didn't work either. How can I get them back?

    Ok this is bizzare!
    Thank you for your response, I went throught each and every step without any luck, even got the recovery programme, and painstakingly tried to sift through all that mumbojumbo to find what i needed. finally found the bookmark bit, but it had been fully overwritten :(, so on reading about previous ff versions, found the sqlite thingys, and they were relatively unscathed(partly written over, but saveable apparently TG), saved them to adiff drive, amongst other possibly good folders. Then looked up how to install them, and it said to close FF, and install to profile folder.
    So i tried to close FF, and the original problem from a few days ago, where it asked me if 'i was sure i wanted to close this window as it has X tabs open', popped up again. This is where 'open blank page' selection was set, over 'open previous tabs'. Wanting to save that info on how to sort out these friggin files, I reset the Option to 'open previous tabs', and closed FF. After unsucessfully searching for the profile folder on my laptop, i opened FF intending to search online for where i could find said folder.
    AND BANG, surprise surprise, the FF I had just closed with only tabs open about finding out what the heck to do, had disappeared, and instead my original saved tabs were up, and my bookmarks are there..... I am gobsmacked! what the heck just happened there???
    I have made 3 back up in different folders now, of those friggin bookmarks. I am weary now tho of shutting it all down.... what if its back to the other pages I had with no bookmarks, tomorrow :(

  • TS1489 My songs won't play on Windows 7 version of iTunes. Everything on my PC is up to date. Windows Media Player works fine. I followed the directions and nothing has changed. I have already tried to re-install iTunes but that hasn't worked either.

    My songs won't play on Windows 7 version of iTunes. Everything on my PC is up to date. Windows Media Player works fine. I followed the directions and nothing has changed. I have already tried to re-install iTunes but that hasn't worked either. If anyone knows how to solve this problem please E-Mail me at [email protected] or reply to this message.

    Itunes worked after reseting my computer to factory setting however had trouble again after syncing my iPod and iPod shuffle. Is this a coincidence or could it be the cause of the problem?

  • Hot backups for essbase planning databases

    Hi gurus
    Can please tell me best advice for making hot backups of our essbase planning databases for disaster recoveries?
    We try doubletake but files are locked unless essbase is put in read-only mode.
    Any good tools for this? Certified stuff? Heard maybe VBE?
    TIA
    M.

    Hi,
    First of all have you read the document of backing up essbase :- http://download.oracle.com/docs/cd/E10530_01/doc/epm.931/hfm_backup.pdf
    If you are taking a backup while essbase is running then you will need to put the databases into read only mode, this can be done by using a maxl script and once again to take it out of read only mode.
    There are lots of 3rd party applications out there for backing up file structures, it all depends on what you want it to do and how much you want to pay.
    If it is a small installation you could even script it yourself depensing on your knowledge to back up files and copy them to a san or backup drive.
    Cheers
    John
    http://john-goodwin.blogspot.com/

  • Hot backup in essbase

    hi all,
    is there any way to do a hot backup for essbase database.
    i need to know regarding to DRC scenario for my essbase db.
    please share with me if there is any solution for this..thx
    regards,
    dityo

    Have you read the essbase section in the backup and recovery guide - http://download.oracle.com/docs/cd/E17236_01/epm.1112/epm_backup_recovery_11121/launch.html
    If you want a different version go to the docs at - http://www.oracle.com/technetwork/middleware/epm/documentation/index.html
    Cheers
    John
    http://john-goodwin.blogspot.com/

  • My phone turns off saying it needed to be plugged in and i plug it in and it says it has 27% and i already tried resetting it! Are they able to help me or am i out of luck ? I already got a different iphone because my very first one didnt work and

    My phone turns off saying it needed to be plugged in and i plug it in and it says it has 27% and i already tried resetting it! Are they able to help me or am i out of luck ? I already got a different iphone because my very first one didnt work and the second one is not working either.

    When you erased the disk did you select Mac OS Extended Journaled as the format option?

  • TS1398 my iphone 4s has stopped access to wi-fi and I cant turn the wifi from off to on. how can i reset this? i already tried the reset setting

    my iphone 4s has stopped access to wi-fi and I cant turn the wifi from off to on. how can i reset this? i already tried the reset setting

    iOS: Wi-Fi settings grayed out or dim

  • Sync from iPhone to iCal on MacBook has failed since the latest iPhone upgrade, yesterday.  It's worked in reverse, and all other sync operations appear to have worked.  Any solutions, that I may not have already tried (over and over)

    Sync from iPhone to iCal on MacBook has failed since the latest iPhone upgrade, yesterday.  It's worked in reverse, and all other sync operations appear to have worked.  Any solutions, that I may not have already tried (over and over)
    (Sorry, first time user of these forums, and it's confusing in it's own right)

    You may have to try deleting all the music from your phone (by going to Settings>General>Usage>Music, swipping All Music and tapping Delete), then sync it all back on with iTunes in order to fix this.

  • My iphone 5s has no signal. I already tried the reset. but no change. I bought it less than 2 months. What can I do?

    My iphone 5s has no signal. I already tried the reset. but no change. I bought it less than 2 months. What can I do?

    I will. thanks

Maybe you are looking for