Has the firmware upgrade on the time capsule been fixed to allow iphones on the wireless network? I reloaded the previous firmware edition and it fixed the problem. thx
I checked beofre on the support communities when I was having trouble with the iphone 4 not being able to connect to the time capsule wireless after upgradeing the firmware. When I reloaded the previous firmware version, the iphone wireless problem was gone. Now the time capsule is asking to upgrade to that same newer version of firmware.
I don't want to do it until the iphone 4 wireless connection problems have been addressed. thanks
......will other users on the primary network (not the private wifi one) be able to access my files on my TCapsule?
No, if you have not provided them with the Time Capsule device password.
Users will be able to "see" the Time Capsule icon under the SHARED heading in the Finder on their Macs, but they will not be able to access the drive or the files.
I had also been thinking about wirelessly extending the wifi network (a linksys N router) but I guess that will allow everyone to access my Time Capsule?
Same answer as above.
Similar Messages
-
Can I use Time Capsule as a secure Shared drive on my wireless network?
Can I configure Time Capsule as a secure Shared drive on my wireless network for the other 3 Macs in my family?
Thanks
KeithYou can require users to enter a password to access the Time Capsule disk, if that is what you mean by "secure".
-
I just setup my cable and internet at my new place yesterday thru comcast. The internet works when it is plugged directly from my modem to my iMac but when I try to plug the modem up to my time capsule to set up wireless and go through air port utilites it can not find my time capsule
Anytime you change networking hardware, it is always a good idea to perform a complete power recycle of your networking components.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results. -
I have an AT&T modem that serves as our home wireless network. I wanted to backup up our computer data so I got a time capsule to back up our three household MACs. After purchase, I found how that I needed to put the exising modem in "bridge mode" so the Time capsule would establish the network. Four frustrating hours later talking to 3 different people at Yahoo, I got the **** thing established. It worked fine for 4 months - then a power failure forced me to repeat the process again. I had to reestablish everything and it took another 4 hours. After 6 months, another power failure forced me to go through the entire process again. Now, of course, Yahoo is charging a fee to help you establish the TC as the network if you have one of their modems - and to make things interesting, they really don't understand MACs. After 5 hours, in frustration, I gave up and asked the Yahoo folks to just put their modem back in as the network hub and I unplugged the Time Capsule. Now after 3 months of looking at an expensive Time Capsule and searching the internet for help, I figured I try the Apple help network,
I just want to backup the data on my MACS. I have a network in the house that works just fine. How do I configure the TC to work as a backup on a wireless network? It seems like it should be simple, but it isn't. Can anybody help?I have no idea about the modem and bridge mode (I don't do networking -- hopefully Bob Timmons, Tesserax, or one of the other networking gurus will drop in and address that).
But . . . you should be able to back up to the TC as long as it's on your network and recognized by your Macs. I think being in bridge mode means it will be rather slow, but it should work. Until/unless we hear otherwise, you might want to see #Q1 in Using Time Machine with a Time Capsule. -
Time Capsule used as router attached to Comcast Modem. Wireless stops working with no light showing and Link indicator on modem off.
All I have to do is unplug the TC and plug it back in.
TC cycles up and green light appears as well as the Comcast modem operates correctly.
TC 4 yrs old. How do I correct?I have the latest and greatest Time Capsule and Comcast. Here is the weird thing. If I have one network set up, then occasionally that network will wedge. If I set up a 5GHz and a 2.4GHz network, then one of them (usually the 5GHz) will wedge. I saw this with a previous Time Capsule, Apple said call Comcast. They checked it out and said it was Apple's problem. Apple said maybe you Time Capsule is bad, so I bought a new one. The problem persists.
Tonight it's not complely wedged, but super slow. The 5GHz network is getting 0.45Mb/s while the 2.4GHz network is getting 17Mb/s. Both are coming in from the same Comcast cable modem. Apparently the Time Capsule treats them as separate.
Is it the cable modem or the Time Capsule. I am betting on the Time Capsule, since rebooting it fixes the problem. Resetting the cable modem does not.
Apple is NO HELP at all. They say reset the Time Capsule. Did that fix it? Yes. Problem solved! No, problem not solved. It will happen again in a few hours.
Here's the traceroute. Note what happens a few hops away. At hop number 7 the ping times go up by a factor of 200.
Huginn:~ darrell$ traceroute 128.114.48.10
traceroute to 128.114.48.10 (128.114.48.10), 64 hops max, 52 byte packets
1 10.0.1.1 (10.0.1.1) 0.952 ms 0.886 ms 3.428 ms
2 67.170.200.1 (67.170.200.1) 43.269 ms 27.611 ms 21.004 ms
3 te-7-1-ur01.scotts.ca.sfba.comcast.net (68.85.101.53) 11.252 ms 8.450 ms 9.778 ms
4 te-1-5-0-7-ar01.sfsutro.ca.sfba.comcast.net (68.87.226.14) 15.026 ms 27.372 ms 15.516 ms
5 he-3-9-0-0-cr01.sanjose.ca.ibone.comcast.net (68.86.91.45) 14.374 ms 17.450 ms 24.752 ms
6 pos-0-0-0-0-pe01.529bryant.ca.ibone.comcast.net (68.86.86.122) 14.627 ms 15.408 ms 14.460 ms
7 xe-1-2-0.0.paix0.tr-cps.internet2.edu (137.164.130.233) 1583.490 ms 2697.533 ms 3240.337 ms
8 xe-1-1-0.482--2152.paix0.tr-cps.internet2.edu (137.164.131.62) 2413.800 ms 2937.085 ms 2667.384 ms
9 dc-svl-core1--svl-px1-10ge-3.cenic.net (137.164.46.14) 4362.188 ms 2399.774 ms 1397.535 ms
10 dc-svl-agg1--svl-core1-10ge.cenic.net (137.164.47.120) 588.755 ms 2447.772 ms 1795.253 ms
11 137.164.3.49 (137.164.3.49) 3179.385 ms 1718.755 ms 240.350 ms -
I got the error message that my Time Capsule "iMac.sparsebundle could not be accessed (error - 1). It backed up fine yesterday. Anyone else have this problem?
If it helps I am getting the same message, I have reported it to Apple and they have someone working on it. Mine stopped backing up after having a new hard drive installed. I can however back up to the same time capsule from my laptop.
-
Hi , I have recently bought an second hand iPhone 4 , Now most of the thing on the iPhone you need iCloud ,i try logging on to it but when i do it say The maximum number of free account have been activated on this iPhone, i don't know what to do. Help
When you have kernel panics, the pertinent information is in the panic report.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
In the Console window, select
DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A panic report has a name that begins with "Kernel" and ends in ".panic". Select the most recent one. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
If you don't see any reports listed, but you know there was a panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report.
I know the report is long, maybe several hundred lines. Please post all of it anyway. -
How can I confirm that the back up to my time capsule has backed everything up as when I enter time capsule and interrogate the backs ups I can't identify individual photo or music files?
You cannot browse a Time Machine backup with the Finder. To restore individual music files or any other files normally available in the Finder, open your Music folder then "Enter Time Machine" using the Time Machine icon.
Restoring individual photographs is slightly more cumbersome. Apple recommends restoring the entire iPhoto Library, but if you want to locate an individual photograph you could use Time Machine to restore the old Libary. Restore it to an alternate location to avoid overwriting your existing one. Open iPhoto while holding an Option key, open the restored Library, find the photo you need and export it, close iPhoto, re-open it with your usual Library, and import the photo.
Time Machine depends upon a number of sound engineering principles for reliable operation, one of which is "faith"
Your files will remain intact until your Time Machine backup device becomes inoperative. -
How can I test the usb port on my Time Capsule to see if it is working?
Ever since lightening struck nearby (which took out our internet and copy machine) the printer I had connected to the usb port on my Time Capsule in my office has has failed to print through the TC. I can plug the printer directly into my MacBookAir and can print just fine. So there is nothing wrong with the printer nor the usb cable.
I've turned off and unplugged the printer with the usb cable connected & disconnected to the TC, no change. I've unplugged the TC, no change. I've opened the printer utility several times, and always get the "offline" error. I open the print queue, and it says the printer is not connected. I reinstalled the driver for the printer, still the same thing.
I'm starting to wonder if the usb port on my Time Capsule got fried. Any help anyone can give in trying to see if the usb port even functions anymore would be greatly appreciated.
My Time Capsule is model no. A1409.Power is not likely to be killed .. it is the data components that are more fragile.
So you do have power which as you say is why the USB flashes.. but you don't have signal.
The only other thing you can do is use USB powered hub.. if you have one handy.. but I would not go out and buy one.
A damaged board is impossible (at cost less than replacement TC) to repair. And repairers do not like working on stuff damaged by lightning as components that did survive were stressed.. the transistor junctions become liable to fail at any time.. so you repair it and it just keeps coming back as not working. Sorry if you cannot use it without USB junk it and buy a replacement. A second hand Gen3 is about the best of them it seems.
You can also buy an ethernet to USB print server.. but a new ethernet or wireless network printer is probably near to the same price.
You can hunt ebay for second hand USB print servers.. or airport express, extreme or TC.. often you can find something suitable for just a few dollars if you shop well. Since you don't need the latest greatest to do this sort of job.. and people are disposing of things like USB print servers as soon as they buy network printers. -
I keep getting this message: The backup disk image “/Volumes/Time Capsule/Coyner’s iMac.sparsebundle” is already in use. What should I do?
SeoulTom (Coyner)Make sure that no other Macs are backing up at the time
Pull the power cord from the back of the Time Capsule
Count to ten
Plug the power cord back into the Time Capsule
Wait a few minutes, then try a backup again
Check to make sure that you are running firmware 7.6.4 on the Time Capsule -
How to find the file that delete from time capsule?
How to find the file that delete from time capsule?
I mean I saved JPEG file in Time capsule and unfortunately delete the file. Can I get it back
IF.... .no other backups have occured since you deleted the file, you might be able to retrieve it using an application like Disk Warrior. It's about $100 as I recall, and there are no guarantees that it will work.
DiskWarrior 4 - The Disk Utility for Mac Disk Repair, Mac Directory ...
Any of the free or low priced utilities that you might see or try will not be able to retrieve a deleted file from a Time Capsule.
If any backups have occured since you deleted the file, the deleted file has almost certainly been overwritten. No way to retrieve it in that case. -
I keep receiving this message.
Time Machine could not complete the backup.
The backup disk image "/Volumes/Time Capsule/Karla Laura Smith's MacBookPro.sparsebundle" could not be accessed (error -1).
Can anyone help me clear this annoying message up? Thanks for advance....The unplugging was of power, if you were unplugging ethernet .. that will not do anything.
The issue is explained here.
C17 http://pondini.org/TM/Troubleshooting.html
If a restart of the TC is not adequate you maybe in the 2% that has other issues.. please try a full network restart in correct order.. with everything off.. modem.. then TC.. then clients.. with 2min gap to allow modem and TC to finish boot process. -
HT3486 Can I shared the files/folder of my time capsule with Mac/PC/iPad outside my lan?
Can I shared the files/folder of my time capsule with Mac/PC/iPad outside my LAN?
Mac yes.. use BTMM and iCloud or direct AFP connection to the TC.
There is huge amount of info.. just look up remote access time capsule.
PC no.. there is no AFP protocol application that I know of.
iPad no,.. again it is not an AFP protocol device. The only open access method apple allowed is BTMM which doesn't work for ipad.
If you want access for PC and ipad you need to replace the current modem router combo.. whatever it is with one that includes vpn server endpoints.. these can be fairly cheap.. plenty of products with 3rd party firmware will work. VPN is far superior method. -
how do i access the data stored on my time capsule? for example, if i try to view a photo, i get the option to "view with iphoto" but when i click on "view with iphoto" nothing happens. i'm having similar trouble openning up movies, music, etc. it appears as though the files exist / saved on the time capsule (because i can see how much storage they consume), but i can't open them. thanks!
Unfortunately, Apple removed the feature to "browse backups" in Time Machine backups of iPhoto a few years ago.
You have to restore the entire iPhoto library to a separate location to be able to "see" it, and then choose the specific images that you want use.
For complete details, see #15 in Pondini's excellent support document Time Machine -- FAQ. Check the information in the pink box there.
Frequently Asked Questions -
I ran out of space on my time machine because I bought a new I MAC to replace the old one. So I copied the old one on the new one and in addition to that I own a macbook. So what should I do erase the old IMAC on my Time capsule ? Shall I reset it?
Go to the airport utility and erase the TC disk.. a quick erase is fine and takes less than 1min usually.
A one pass erase takes several hours depending on how big the hard disk is.. but is somewhat safer in that it tests the drive condition. I normally don't bother for a TM backup.
When you start over you should be able to fit both backups on the TC.. assuming the disk is 2x larger at least than the space used on both the MB and the iMac.
If not you can also add a USB drive to the TC, and use that for one of the computers.
The slowest one is best.. as USB is slow.. but fast enough for wireless you won't notice much. -
How to plug a hard drive on the USB port of a Time Capsule. TC in bridge mode
Hello
I would like to connect a hard drive onto the USB port of a Time Capsule. This is for saving files (different frome the Time Machine savings). I am struggling to get it working it seems that I can see the HD when under "drives or discs" (running Snow Leopard in French) from the AirPort Utility but I can't access to it.
The TC is in bridge mode.
Thanks for help and guidances.
Best
PierreThe question is clear enough.. I just don't understand why you are having issues.
Can you see in the internal disk of the TC in the finder?
What format are you using on this disk? Try and format it HFS+ if it isn't already.
If you plug it directly into the Mac it works ok??
The other issue is the need for a powered hub on the TC due to the low power it gives the internal port.. or lack of bios compatibility with a range of usb hub chips. Try a powered hub as that can also help.
Maybe you are looking for
-
Music not showing up for an Artist but does in Recently Adde
I recently moved my music files from a windows computer to a Mac and uploaded into iTunes. I also switched from a 40 GB to a 60 GB iPod. I synched the music to the new (60 GB) iPod and found that the music appears to be synched (it showed up in Recen
-
Replicat an epoch date to a date column
I have a source table that has a number column that stores an epoch date that needs to be copied to a target table as an actual date/timestamp. I would like to have GoldenGate do the actual conversion in the map statement of my replicat using the DAT
-
Sequence (nested) will not open in timeline... help!
As a disclaimer, I am a self-taught FCP user. I am in the final stages of finishing up a 53 minute documentary from footage I shot in Haiti right after the quake. So, I don't know whether it is an, +advised way+ of working, or not, but in my project
-
How to add attributes in Data Column for automatic changes
Hello everybody, Could you give me an advice? I have characteristic and attribute assigned to it. I want to make what when i change characteristic(variable) its attribute in planning layout changes too. So in planning area window in <b>Characteristi
-
Hi all, Is it even possible to change the Effective date of SAP_PA action? I have 4 backend service, SAP_PA Serv_1 Serv_2 SAP_PA I changed EFFECTIVE_DATE ( Field is available as input field in the form) in my Serv_1 also to ensure I changed it in