Hauwei E156B Mobile Broadband USB Driver/Installation File

Hello folks,
I just recently purchase a USB Keyfob for Mobile Broadband. The model number is E156B and it is manufactured by Huawei. I have search up and down Huawei's support forms and downloading multiple software bundles to no avail. I don't think Huawei even supports Mac OSX 106. Snow Leopard. In any case, I figure I would try one last time here to see if someone has successfully configured the E156B through "Tigo" with OS 10.6.2

I used a Huawei E169 Mobile Broadband Modem using a generic 3G Modem setup under Mac OS X 10.6.3.
This is how I set up the modem:
Open System Preferences window (from Apple menu)
Open the Network Preference Pane.
Select the Huawei xxx Modem item from the list of network connections (there were two more Huawei items)
Click on "Advanced" settings.
Select "Generic" as Modem Manufacturer.
Select the 3G Modem type.
enter the provider specific dial number (*99# in my case)
enter the provider specific ID and password (left blank in my case)
enter provider specific APN (in my case "Internet")
you need to check your providers specific settings for the above!
Click on OK button.
Activate Network setting
Choose to select modem in menue bar
Close System Preferences Window...
To connect, go to the menu bar, click on the handset icon and choose to connect.
After use, disconnect as above (depending on your contract, time charges might apply)
Good Luck

Similar Messages

  • Apple mobile device USB driver is missing and cannot be installed

    Hi,
    My iPod nano (6th gen) is not recognised by iTunes but is recognised by Windows sometimes (once in 2-3 attempts).
    Every time I connect my iPod to my laptop, a window pops up saying "an iPod is detected but could not be identified properly...".
    I looked through apple support page and narrowed down the cause to the driver.
    Apple mobile device USB driver does not show up in Device Manager.
    However iPod does show up under Portable Devices as a camera when iPod is recognised by Windows.
    I tried reinstalling Apple Mobile Device USB Driver as it was shown in the support page (right click on iPod in Device Manager>update driver software>...).
    This did not work (gave me an error saying "the folder you specified doesn't contain a compatible software driver for your device...".
    So I tried another method I found online; extract iTunes installer (itunes6464setup.exe), extract AppleMobileDeviceSupport6464.msi in it, and use the files in it to update driver.
    This gave me the same error.
    It seems that a Windows driver is installed for my iPod (WPD FileSystem Volume Driver); when I opt for "search automatically" in Uptade driver software, this driver shows up with the message "the best driver for your device is already installed".
    Also, my iPod is shown in Devices and Printers with an exclamation mark (when I connect my iPod to my laptop, the exclamation mark shows up only after I click OK on the message window "an iPod is detected but could not be identified properly...")
    Troubleshoot showed "Windows is uninstalling this device (Code 21)".
    I'd appreciate it if someone could help with the situation.
    I'm using Windows 8.1, iTunes 12.1 for Windows 64bit, and iPod nano 6th gen.
    I haven't connected my iPod to my laptop for a long while, but I recall connecting an iPhone to my laptop a while ago and it was recognised just fine.
    After that I updated my Windows from 8 to 8.1, but I don't think it has anything to do with the problem as my iPod wasn't recognised by iTunes before and after the update.
    Thank you in advance!

    For general advice see Troubleshooting issues with iTunes for Windows updates.
    The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
    Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
    If the advice above doesn't resolve things you could try this alternate version:
    iTunes 12.1.0.71 for Windows (64-bit - for older video cards) - itunes64setup.exe (2015-01-28)
    which is a 64-bit installer for the 32-bit version of the core application, similar to previous 64-bit releases. Or roll back to the previous build:
    iTunes 12.0.1.26 for Windows (32-bit) - iTunesSetup.exe (2014-10-16)
    iTunes 12.0.1.26 for Windows (64-bit) - iTunes64Setup.exe (2014-10-16)
    tt2

  • Unable to install Itunes 10.1 or 10.1.1  -Apple Mobile Device USB Driver

    Unable to install Itunes 10.1 or 10.1.1 and have it sucesfully install the Apple Mobile Device USB Driver. It keeps coming up with an error that the driver is unsigned or disappears completely from device manager.
    I have tried full uninstall including cleaning registry keys and file system. If I uninstall and re-install 9.2.1 usb driver works perfectly and I have no issues synching with phone or seeing the phone in Itunes.
    I have tried repair installs, updating the drivers by pointing to C:\Program Files\Common Files\Apple\Mobile Device Support\Drivers
    I have tried removing all USB devices and having them reinstall from Windows after a reboot. Nothing seems to work.
    I just got a new IPAD and cannot use it because I cannot install 10.1 at least to have it connect. It came with IOS 4.2.1 on it.

    I also encountered the same problem.
    and yes, I uninstalled and reinstalled itunes 10.1.1 bla bla blahhh....
    Same issue!!! itunes cannot open cuz the mobile device support not started etc..
    but when reinstalled prior itunes version 9.2 its gone
    and issue fixed.
    i can sync my 3G.
    but not my 4G. it says you need to upgrade to 10.1 or above
    spending the whole night to fix the problem which never occured b4
    i finally find out one thing.
    pl keep in mind im not a computer exprt
    i tried this and it worked, i don know what fixed it, bt it works
    try this at your own risk. some comp genius will tell us weather this way is right or not.
    ok. lets start...
    in your desktop make a new folder. name it Kmh_\CoreFP
    try uninstalling the newer version 10.1
    only the itunes not other mobile div suprt, application suprt etc.
    dont mind the following order:http://support.apple.com/kb/HT1923
    and reinstall itunes 9.2
    go to C:\Program Files\Common Files\Apple
    you wil find a folder named "CoreFP"
    copy it and paste to Kmh_\CoreFP
    uninstall itunes 9.2
    and reinstall itunes 10.1 again
    go to C:\Program Files\Common Files\Apple
    you wil find folder named "CoreFP"
    find the difference in properties comparing the one u stored in Kmh_\CoreFP
    ok delete it and replace it with the one we stored stored in Kmh_\CoreFP
    restart the computer and start itunes now
    what happens?
    best of luck.
    -Kmhm63
    reinstall the newer version 10.1
    I would suggest that you revert back to prior working version until Apple comes out with an update that fixes what 10.1.1 broke.

  • Where is the link to download apple mobile device USB driver software

    I need to download apple mobile device USB driver software but can't find it onlie. Advice where i can download it from much appreciated.

    I had the same problem with my iTouch when I upgraded to iTunes 10. I'm not sure if my problem was the same as with the nano but every time I reinstalled iTunes and plugged in my Touch, I got an error message for driver installation and the Apple Mobile Device USB Driver in Device Manager with a little yellow exclamation mark. The error message that came up stated something about the digital signature of the driver not being right. The fix that worked for me was as follows:
    Delete the 2 Apple Mobile Device USB Driver files. If you right click on the Apple Mobile Device USB Driver in Device Manager and select properties it will tell you where they are located in the windows folder. My 2 files for windows 7 64 bit were:
    usbaapl64.sys
    usbaaplrc.dll
    With ipod disconnected, restart computer and press F8 to enter boot menu.
    Select boot option without digital driver signature support.
    After boot, connect ipod and driver should automatically install correctly without error.
    Good Luck
    I called Apple and they would not provide any unpaid support for iTunes issues.

  • Apple Mobile Device USB Driver is listed in device manager, but has a yellow  "!".  I try reinstall,disable,enable the drivers but the problem persist. Could you help me ?

    Hi
    I connect my ipad to my pc (Windows xp SP3) and I can see my ipad and photos in my computer. When I install the itunes 11 , after installation , I can't connect the ipad again or any other apple device. The Apple Mobile Device USB Driver is listed in device manager, but has a yellow  "!".
    I have try to reinstall the drivers from c:\progamfiles\common files\apple\... but the problem persist. Could you help anyone about this ?

    You need to completely uninstall iTunes from your computer and then download and install it again.
    You do know that Microsoft has a web site, right?

  • The "Unable to install Apple Mobile Device USB Driver" problem

    Ever since I installed iTunes 10, I've had nothing but problems. I tried every fix I could find on the internet, unfortunately there are not too many, Apple's own website has loads of fixes but they never work.
    I keep getting the Apple Mobile Device USB Driver come up in Device Manager with a little yellow exclamation mark and nothing I seem to do can fix it properly. I managed to fix it once, my iPod was synced and all was good, but once I restarted my PC, the problems started again. And I tried my friends iPhone which works perfectly and the same problem came up on my PC.
    Cant someone give me a proper fix please?

    I had the same problem with my iTouch when I upgraded to iTunes 10. I'm not sure if my problem was the same as with the nano but every time I reinstalled iTunes and plugged in my Touch, I got an error message for driver installation and the Apple Mobile Device USB Driver in Device Manager with a little yellow exclamation mark. The error message that came up stated something about the digital signature of the driver not being right. The fix that worked for me was as follows:
    Delete the 2 Apple Mobile Device USB Driver files. If you right click on the Apple Mobile Device USB Driver in Device Manager and select properties it will tell you where they are located in the windows folder. My 2 files for windows 7 64 bit were:
    usbaapl64.sys
    usbaaplrc.dll
    With ipod disconnected, restart computer and press F8 to enter boot menu.
    Select boot option without digital driver signature support.
    After boot, connect ipod and driver should automatically install correctly without error.
    Good Luck
    I called Apple and they would not provide any unpaid support for iTunes issues.

  • Apple mobile device usb driver not digitally signed

    I installed(updated) itunes 12.1.1.4 64-bit on wildows 7. Then, it can not recognize iphones and ipods any more.
    I tried every means to fix this, updating windows and itunes, uninstalling and installing, rebooting and restarting.......
    Finally, I find that the apple mobile device usb driver is not digitally signed.  I found this when I open the computer/manage/device manager/portable device/iphone/update driver.  Windows installed mtp usb driver for apple products and indicating the related apple driver software cannot be installed.
    what's wrong with this?  should I wait until apple solve this problem?

    I suggest you try the "for older video cards" version...
    For general advice see Troubleshooting issues with iTunes for Windows updates.
    The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
    The further information area has direct links to the current and recent builds in case you have problems downloading, need to revert to an older version or want to try the iTunes for Windows (64-bit - for older video cards) release as a workaround for installation or performance issues, or compatibility with QuickTime or third party software.
    Your library should be unaffected by these steps but there are also links to backup and recovery advice should it be needed.
    tt2

  • Apple Mobile Device USB Driver (CODE 52 Error)

    I've been trying to sync my ipod touch with my laptop computer. I recently updated my version of iTunes, and now can not get my ipod to sync with my computer. The problem is in the Apple Mobile Device USB Driver. The error I am getting is a Code 52 error which states: "Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source."  I've tried uninstalling the USB driver along with iTunes and all the related software. I have a windows 7 notebook. Any help resolving this issue would be greatly appreciated.

    Hi ADziack24,
    Thanks for using the Apple Support Communities. The following resource includes an entire section dedicated to the error you are receiving. The steps may help to resolve your issue:
    iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support
    http://support.apple.com/en-us/TS1538#error52
    - Matt M.

  • Apple mobile device usb Driver isn't  working

    I have an Ipod Nano 3rd gen. and the problem i have is that the Apple Mobile Device USB Driver has a yellow exclamation point next to it in device manager. When I try to reinstall driver it says CANNOT THIS HARDWARE THERE WAS A PROBLEM INSTALLING THIS HARDWARE: Apple Mobile Device USB Driver AN ERROR OCCURED DURRING THE INSTALLATION OF THE DEVICE
    DRIVER IS NOT INTENDED FOR THIS PLATFORM.
    I want to know how to fix this. What does it mean by not intended for this platform?
    I've uninstalled every thing that comes with itunes(Bonjour, etc.) and it still won't work. It will sync to my brother's Mac but not to my PC. I've also synced it to my PC before. I need to know how to fix the Apple Mobile Device USB Driver.
    Message was edited by: xxSHABANGxx
    Message was edited by: xxSHABANGxx

    Hello there,
    And welcome to Apple Discussions!
    First of all, sorry to hear you are having so many troubles with your iPod. Take a look at this article for information and help on driver errors and installation. Even if you have already attempted some of these recommended troubleshooting steps, try just once more. It's worth a shot.
    http://support.apple.com/kb/TS1538
    B-rock

  • I disabled "Apple Mobile Device USB Driver" in Windows

    I did this because my device wasn't charging and I was trying (still am trying) to solve that problem.
    But once I disabled the "Apple Mobile Device USB Driver" under the Device Manager the device didn't dhwo up with an "X" next to it it just went away. And now when I plug in ipods it will not show up at all!
    I even booted into safe mode expecting to see more drivers there and I still didn't see the apple one to re-enable it. I should have deleted it then it would have just come back on a re-boot!
    Anyone have any suggestions?

    Re-installing the apple mobile device support under add and remove programs fixed this issue. Found this after many iTunes re-installs.
    Still have a charging issue. I will post that in a different message.

  • WTH!!!! Keep getting msg bubble "APPLE MOBILE DEVICE USB DRIVER"????

    I have wrecked my brain on this one! I have 4 different types of ipods that are being connected to my computer. The one I keep getting the message on is the Nano 3rd gen. The others are an 80 GB and 2 GB that are being recognized on WinXp and ITunes. Everytime the Nano is attached it's recognized by WinXP but not in ITunes. The bubble says "Found new hardware - APPLE MOBILE DEVICE USB DRIVER" Then the other bubble says "Found new hardware - USB MASS STORAGE DRIVER". I then get the window that says CANT INSTALL THE DRIVERS. I have followed the "support" directions on uninstall re-install, update drivers, roll back drivers and whatever else they have on this website. It was working fine until a Touch was plugged in to my computer. Anyone else going through this BS? I don't know what to do. I may try to roll back my system and see if that works. ANYONE WITH A SOLUTION PLEASE HELP!! I am quite irritated now!

    ok sooo I tried to restore my computer...that didnt work. Next I dl that Mobile Me that was offered on the apple update. Didnt work. Then I said forget it and dl ITunes on a completely different computer that never had ITunes on it. Guess what....it worked and recognized my nano and the other 2 I have. I believe that there must be a registry file that is not getting overwritten or deleted completely somewhere along the process of uninstallation or maybe something else isnt getting changed somewhere. Im not that computer savvy but if someone can find what the problem is, let me everyone know.

  • TS1538 What do I do after step 6 in "If the Apple Mobile Device USB Driver is not listed"?

    i'm very confused about step 5, "Verify that the Apple Mobile Device USB Driver is installed" > "If the Apple Mobile Device USB Driver is not listed", what do I do after step 6? I looked for and found the entry that recognizes the device as a camera, "Apple iPhone, now what? I'm trying to resolve an issue. After an iTunes upgrade in July 2012, I have not been able to get my iTunes to recognize any of my devices. I have uninstalled/reinstalled iTunes, all the steps. Now I'm on this one and I don't know what to do after this step 6. I looked and found the entry.... now what??? I am out of room on my phone because everything I buy on iTunes on the computer mysteriously appears on my iPhone 4, and everything I buy on my iPhone mysteriously uploads onto my iTunes the next time I open it. My phone will charge when connected to the computer, and Windows recognizes it and asks how I want to open pictures, etc. But in iTunes it will not show up under Devices. This is getting beyond ridiculous and I have to get some of this music off of my phone!

    Found a possible solution for me.
    While the phone was plugged into my computer and iTunes is CLOSED.
    1. I went to Services in Windows.
    2. I selected Apple Mobile Device and right clicked and selected "Stop".
    3. Then I right-clicked again and selected "Start".
    4. Then I went to Device Manager and right clicked my iPhone with the yellow alert icon and selected "Uninstall".  You will get a warning about uninstalling the device.  Click OK.
    5.  At the top of Device Manager I clicked the Action menu and selected "Scan for Hardware Changes".
    This re-installed the iPhone and everything started working again.

  • I synced my phone lastnight and now it says my phone cant connect to computer the Apple Mobile Device USB Driver doesnt work?!? i deleted itunes and reloaded still not working.... Does anyone know how to fix??? i just want to upgrade to IOS6

    Does anyone know why my Iphone will not connect to my computer all of a sudden? I backed it up lastnight. Now it wont even register with my computer.... It says Apple Mobile Device USB driver doesnt work all of a sudden???? i tryed deleting and reloading and nothing is working!!! someone please help =)

    Have you done:
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    or
    Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
    What results do you get when you run this:
    iTunes for Windows: Device Sync Tests
    Do both the Home button and Power button work OK normally?

  • I updated to iTunes 10.7 and now iTunes does not see my iPod Touch.  It says the Apple Mobile Device USB Driver cannot be installed.

    I updated to iTunes 10.7 and now iTunes does not see my iPod touch.  After the update I got a message that the Apple Mobile Device USB Driver could not be installed.  I have uninstalled and reinstalled iTunes 3 times, but still cannot fix the problem.  I have followed the suggested fixes in Apple Support.   Any suggestions?  Thanks!

    Try the actions here for that driver.
    iOS: Device not recognized in iTunes for Windows
    I would first do this:
    Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

  • IPod touch 5th gen will not connect to iTunes, also apple mobile device usb driver does not appear in device manager. PLEASE HELP.

    I recently purchased my iPod touch with no issues. After updating to iOS 8.1.1 I found that my iPod would no longer appear in the latest version of iTunes and when I searched for Apple Mobile Device usb driver in the device manager, it was nowhere to be found. I've already uninstalled and re-installed ALL components of iTunes and read every single help article. I've tried everything. What went wrong?

    See
    iOS: Device not recognized in iTunes for Windows
    - I would start with
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    or                     
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
    - Then do the other actions of:
    iOS: Device not recognized in iTunes for Windows
    paying special attention to item #5
    - New cable and different USB port
    - Run this and see if the results help with determine the cause
    iTunes for Windows: Device Sync Tests
    Also see:
    iPod not recognised by windows iTunes
    Troubleshooting issues with iTunes for Windows updates
    - Try on another computer to help determine if computer or iPod problem

Maybe you are looking for

  • Ipad calendar list

    My iPad calendar day, week and month views are correct (synced with google) but when I go to the list view the days are time shifted back 3 days. Anybody have insight regarding this?

  • Windows 7 64bit freezing in normal mode even after rebooting to Factory Mode?

    Hey guys, my Windows 7 64 bit laptop recently began permanently freezing after a few minutes after logging into normal mode, ultimately forcing me to turn the laptop off with the power button. It only works in safe mode :( Ive tried restoring to an e

  • Item data in smartform

    hi, in my main window i am having 5 columns. out of which one column contains the item datas like: for one delivery order in second column it should have: description (code no) no  of packs type of material. for this should i create 4 text elements?

  • JCO connection to SRM system - in Supplier collaboration 2.0 BP

    Hi Friends, We have deployed the Supplier Collaboration 2.0 Business Package on SAP Enterprise Portal 7. After deployed, we need to configure the JCO to SRM System. We are not configuring for catalog, IHS, et. Now, Under the 'Supplier Portal Administ

  • An unnamed file contains an invalid path

    Hi. I'm using Flash CS3 on Windows XP Pro (SP3) and for the past two weeks, when attempting to save a file, I've been getting a dialog which is headed as "Adobe Flash CS3" and reads: "An unnamed file contains an invalid path. OK" After clicking OK, t