Have lost Hotmail since latest update

Since latest update cannot open Hotmail ,screen is blank apart from send ,reply icons etc along top of screen.
mail is coming in number of mails goes up on mail icon but can't access .

There are several possible causes for this issue. Take each of the following steps until it's resolved.
1. Follow the instructions in this support article.
2. Reset the System Management Controller.
3. If you're using a Bluetooth trackpad, investigate potential sources of interference, including USB 3 devices.
4. A swollen battery in a MacBook Pro or Air can impinge on the trackpad from below and cause erratic behavior. If you have trouble clicking the trackpad, this is likely the reason. The battery must be replaced.
5. There's a report that a (possibly defective) Thunderbolt Ethernet adapter can cause the built in trackpad of a MacBook to  behave erratically. If you're using such an adapter, disconnect it and test.
6. There's also a report of erratic cursor movements caused by an external display that was connected but not turned on.
7. If none of the above applies, or if you have another reason to think your computer is being remotely controlled, remove it from the network by turning off Wi-Fi (or your Wi-Fi access point), disconnecting from a Bluetooth network link, and unplugging the Ethernet cable or USB modem, whichever is applicable. If the cursor movements stop at once, you should suspect an intrusion.
8. Make a "Genius" appointment at an Apple Store to have the machine tested.

Similar Messages

  • Unexpected crashes with no particular rhyme or reason have been occurring since latest update (6.0.2) installed 2 days ago. How can I go back to an earlier version?

    Please check for crash reports sent 9/7-8/11 with e-mail address [email protected]

    Hello BobB10 and welcome to the BlackBerry® Support Community Forums.
    Sorry to hear you are having issues with your BlackBerry® Torch™ 9860 smartphone.
    It is not recommended to downgrade your software, however, if you wish to do so you will need to consult your mobile carriers download site at www.na.blackberry.com/eng/support/downloads/download_sites.jsp and see if the previous software version is posted. If so, download and install it to your computer then use the BlackBerry® Desktop Software to install the older software version.
    Hope this answers your question.
    -HMthePirate
    Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
    Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

  • Final cut pro x - lion - mbp 2011 2.0 15 - not responding at all since latest update. Can't open or edit projects, loading window that pops us when you click the app (as it loads) does not go away, says loading compressor support.  Have tried reinstalling

    final cut pro x - lion - mbp 2011 2.0 15 - not responding at all since latest update. Can't open or edit projects, loading window that pops us when you click the app (as it loads) does not go away, says loading compressor support, paralyzed.  Have tried reinstalling, default settings etc
    Appreciate suggestion, working on deadline. Thanks.  

    Here is the start of the crash report:
    Process:         Final Cut Pro [20568]
    Path:            /Applications/Final Cut Pro.app/Contents/MacOS/Final Cut Pro
    Identifier:      com.apple.FinalCut
    Version:         10.0.1 (185673)
    Build Info:      ProEditor-185670300~1
    App Item ID:     424389933
    App External ID: 4138831
    Code Type:       X86-64 (Native)
    Parent Process:  launchd [102]
    Date/Time:       2011-11-11 20:41:32.201 -0800
    OS Version:      Mac OS X 10.7.2 (11C74)
    Report Version:  9
    Interval Since Last Report:          192058 sec
    Crashes Since Last Report:           14
    Per-App Interval Since Last Report:  157161 sec
    Per-App Crashes Since Last Report:   14
    Anonymous UUID:                      DD542B2F-58A0-482E-AAFA-ECADEC76F562
    Crashed Thread:  0  Dispatch queue: com.apple.main-thread
    Exception Type:  EXC_BAD_ACCESS (SIGSEGV)
    Exception Codes: KERN_INVALID_ADDRESS at 0x0000000280000003
    VM Regions Near 0x280000003:
        CG shared images       00000001cbf62000-00000001cc182000 [ 2176K] r--/r-- SM=SHM 
    -->
        STACK GUARD            00007fff5bc00000-00007fff5f400000 [ 56.0M] ---/rwx SM=NUL  stack guard for thread 0
    Application Specific Information:
    objc[20568]: garbage collection is OFF

  • HT6065 Since latest update i have a login loop, can someone help?

    Since latest update i have a login loop, can someone help?

    Hold down the Power button for 5-10 seconds until the computer shuts down. Restart. Report what state the computer is in at that time.

  • Since latest update to airport extreme im getting 10 unknown base station and time capsule items showing in airport utility as a network.  when able to "forget" them they initially drop off but soon return. how do i get them deleted and stay that way

    since latest update to airport extreme im getting 10 unknown base stations and time caps showing up as though they are a part of my network. sometimes i can "forget" them and they will disappear initially but soon return. i need and want only my connection inside my home . any ideas. i have done a factory reset and set up a new network but they continue to show up.

    I'm not convinced that the problem lies in Airport Utility. This same thing was happening to me, nearly exactly as you describe it. The thing is that with me, the problems clearly started when I updated the firmware in my Airport Express (n). That's when all the wacky stuff started happening. Sometimes it would show up in AU, sometimes it didn't and even if it didn't, I could still access the internet through it.
    But as you said, the problems got really bad when another Express (b/g) was put on the network with it. Even when it did work, the (b/g) would make it impossibly slow.
    You know more about this than me, and clearly have more patience if you've restarted the network fifty times. I gave up at about ten.
    In any case, your solution is more of a work around and if you're still having that slow connection problem, I'm not sure you've got it. But thanks for your reporting of this. At least I know I'm not crazy.

  • My Windows XP and Windows 7 iTunes no longer 'see' my AppleTV since latest update (25/02/2013). Also, my AppleTV tells me I must turn on Home Sharing which is already turned on.

    My Windows XP and Windows 7 iTunes no longer 'see' my AppleTV since latest update (25/02/2013). Also, my AppleTV tells me I must turn on Home Sharing which is already turned on. I have the little arrow that normally selects my AppleTV in iTunes but AppleTV is no longer listed (only My Computer). Is there an issue with the latest update. This is probably my fault by telling everyone how good AppleTV is and that it just works! Doesn't work any more :-( I have tried all the usual restarting of AppleTV and PCs. I'm having to revert back to the Samsung Blu-ray player's PC sharing :-(

    Restarted router(s) and it works again.

  • HT202157 My apple tv 3 doesnt work at all since latest update, how can I restore when it wont even turn on?

    Having trouble with my apple tv since latest update, it has died and can't turn on as it doesn't recognise anything, what can I do?

    Welcome to the Apple Community.
    If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
        1.    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
        2.    Connect the micro USB cable to the Apple TV and to your computer.
        3.    Reconnect the power cable (only for Apple TV 3)
        4.    Open iTunes.
        5.    Select your Apple TV in the Devices list, and then click Restore.
    (You may already have a micro USB cable if you have a camera or other digital device)

  • My young kids have ipads and since I updated the software, but they have their own icloud account, predictive text within their messages shows all my contacts from my iphone but the contacts are not listed as their contacts, how do I stop this?

    My young kids have ipads and since I updated the software, but they have their own icloud account, predictive text within their messages shows all my contacts from my iphone but the contacts are not listed as their contacts, how do I stop this?

    I have deleted the iCloud account under my name on their iPads and replaced with their ones. Apple support said yesterday I needed to click the small 'I' by each name as it came up in the TO box and remove it. After doing rid for each contact under each letter of the alphabet it should remove them from latest contacts. Having done this, although I could not remove groups I had sent, I am not convinced they will not return once I have written a few texts, any ideas?

  • HT6058 my ipad screen will not rotate since latest update

    my ipad scrren will not rotate since latest update, i have done everything i can think of including wha tapple told me

    What have you tried, and what did Apple tell you ?
    Is there a lock symbol at the top of the screen next to the battery indicator ? If there is, then depending on what you've got Settings > General > Use Side Switch To set to (rotation lock or mute notifications), then you can lock/unlock the rotation by the switch on the right hand side of the iPad above the volume switch, or via control centre : swipe up from the bottom edge of the screen and it's the right-most of the 5 icons in the middle of it (if the icon is white then it's 'on', tap it to turn it grey and 'off'). The function that isn't on the side switch is set via control centre instead : http://support.apple.com/kb/HT4085
    If there isn't a lock symbol then try a soft-reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

  • Cannot send virginmedia webmail since latest update

    Can send virginmedia webmail with other browsers. Virgin have checked and all connections are fine - they can use my webmail but since latest update I cannot

    See
    iOS: Device not recognized in iTunes for Windows
    - I would start with
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    or              
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
    - Then do the other actions of:
    iOS: Device not recognized in iTunes for Windows
    paying special attention to item #5
    - New cable and different USB port
    - Run this and see if the results help with determine the cause
    iTunes for Windows: Device Sync Tests
    Also see:
    iPod not recognised by windows iTunes
    Troubleshooting issues with iTunes for Windows updates

  • I use OverDrive to get audiobooks from my library to listen on my ipod. Does not work since latest update of ipod. Converts the WMA and acts like it is putting it on the ipod but then it isn't there.

    I use OverDrive to get audiobooks from my library to listen on my ipod. Does not work since latest update of ipod. Converts the WMA and acts like it is putting it on the ipod but then it isn't there.

    Downgrading the iOS is not supported by Apple.Have yo tried:
    - Backing up and restore from backup. See:                                               
    iOS: Back up and restore your iOS device with iCloud or iTunes
    - Restore to factory settings/new iOS device.                       
    - Go to the OverDrive support site

  • How come whenever i plug my iPhone 5 into the computer the device will not show up on my itunes.  This is the first time that i have done it since i updated to iOS7 and before i had no problem but now it just wont work.

    How come whenever i plug my iPhone 5 into the computer the device will not show up on my itunes.  This is the first time that i have done it since i updated to iOS7 and before i had no problem but now it just wont work.

    Hi Celia51510,
    Welcome to the Support Communities!
    The article below may be able to help you with this issue.
    Click on the link to see more details and screenshots. 
    I can't tell from your post if you are using a Windows or a Mac Computer.
    Try deleting the iTunes application and redownloading the version you need below:
    iTunes 11.1 Download for Mac
    http://support.apple.com/kb/DL1614
    iTunes 11.1 for Windows (64-bit)
    http://support.apple.com/kb/DL1615
    Cheers,
    - Judy

  • I have just downloaded the latest update for Pages on my iPad and now it can no longer open up documents in iCloud and then just shuts down. What The.

    i have just downloaded the latest update for Pages on my iPad and now it can no longer open up documents in iCloud and then just shuts down. What The.

    Before the reset quit Pages like this:
    Double click the Home button to show the screen with running and recently used apps. Each app icon will have a sample page above it. Flick up on the page (not the app icon) and the page will fly away and the app icon will disappear. This quits that app.

  • FaceTime and iMessages have stopped working since i updated to 7.0.3, saying there is a network error and to try again later. Have tried reinstalling Find my iPhone to see if it works. It doesn't for me. Can u please help???

    FaceTime and iMessages have stopped working since i updated to 7.0.3, saying there is a network error and to try again later. Have tried reinstalling Find my iPhone to see if it works. It doesn't for me. The message says "FaceTime (iMessage) Activation: Could not sign in. Please check your network connection and try again". My network is perfectly alright as I keep buying on the App Store. can u please help out???

    (A) Reset iPad
    Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
    Note: Data will not be affected.
    (B) Reset all settings
    Settings>General>Reset>Reset all settings
    Note: Data will not be affected but settings will be reset.

  • I have just installed the latest update ...IOS 7.0.4. Prior to this, my email worked fine. Now my AOL does not work; it gives an ID/password error. Everything works fine on my Windows computer. Any thoughts?

    I have just installed the latest update - IOS 7.0.4. Prior to this, my AOL email worked fine. Now it gives an ID/password error message. However, everything is fine on my Windows computer. Any thoughts?

    Hello there, Tim.
    The following Knowledge Base article provides some good troubleshooting steps for working on resolving your issue:
    iOS: Troubleshooting Mail
    http://support.apple.com/kb/ts3899
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

Maybe you are looking for

  • Help with French Accent Characters Corrupted

    Hi, All. I am developing a Flex Front end connect with Java back-end. The back-end sends data retrieved from XML file to the Flex front-end; displays it in an TextArea, and allow user to change. After user changes the data, hit "Save" button, then Fl

  • Diplay Functional,Reporting and Local currency

    Hi, I've a requirement to display Transactions in functional,Reporting as well as in Local currency.Do I need to setup Oracle 11i Env in MRC for that?If so how to get the transactions displayed in Local cuirrency ?Do I need to Covert them or I've to

  • Site Definition Requirements to use Spry

    What do my site definitions need to be set at to use Spry.  I am using both DW 4 & 5. Thanks

  • DB2 8.1(ver) Full Backup

    HI Experts, I am planning to take the full backup in DB2. I am using SAP on Windows server 2003 platform with DB2 8.1 Version. Please share if any document is there, it will be great help for me. Thanks in Advance. Regards, Raj

  • IPad photos disorganised after 'rebuilding' library

    Our photos in the library used to be organised nicely by date then we received some photos of our family in an email and tried to save them but it didn't save them but started ' rebuilding' the library and now they are all disorganised. The photo on