Have to restore OS X.9.1 after booting into Windows 7 on Bootcamp

I am having an odd problem--whenever I boot into Windows 7 on bootcamp, when I then boot into Mac OS X.9.1, I have to restore the disk from Time Machine. This has never happened before, but now has happened twice in a row. It takes hours for the Restore function to restore everything. Anyone have any idea as to why this is happening. My MacPro dates to 2010. Thanks.

Windows is a guest on your Mac. If you use Windows tools to change the partition Map, or the size of any partition, all Mac OS X partition information is trashed, and you will need to restore it before proceeding.
Otherwise, you should be able to hold down Alt/Option key at Startup, and select your Mac OS X Volume to boot from (after several minutes of discovering what Volumes are present).

Similar Messages

No SATA drive after booting into Windows (BootCamp 5.0)

One of my DVD burners has failed in one of my 2008 Apple Mac Pro's. I pulled the drive out (it was PATA/IDE) and replaced with a new LG WH14NS40 Blu-Ray Burner. I had to pull the fan out (temporarily) and run a new 24" SATA cable (with right-angle connector) from one of the two extra SATA ports (on the motherboard) to the new actual SATA drive, and also install a MOLEX to SATA power connector.
I managed to get the drive installed (and working). I now at least have a Blu-Ray burner in my 2008 Apple Mac Pro (with OS X 10.8.3 Mountain Lion).
The problem seems to be with when I boot directly into Windows 8. When I boot into Windows 8, the two ports on the motherboard are disabled and the latest BootCamp 5.0 drivers don't seem to support the two SATA ports on the motherboard (they seem to be disabled). So when I boot directly into Windows, my LG WH14NS40 Blu-Ray drive disappears.
I really wish Apple would have just "done things right" from the very beginning and took the time to write decent BootCamp 5.0 drivers that supported the two SATA ports on the motherboard, so that users who need to replace their old/dying/aging PATA drives could easily replace them with SATA drives and use the two SATA ports on the motherboard.
Also it would have been nice if Apple would have taken the time to write good BootCamp 5 drivers (for Windows 8) that support booting from the two SATA ports on the 2008 Apple Mac Pro motherboard.
I've heard of many people that have tried installing RAID Controller Cards (from OWC) in their 2008 Apple Mac Pro to upgrade their four hard drive caddys from SATA II (3Gbps) to SATA III (6Gbps) but unfortunately the RAID Controller Cards don't seem to be bootable and the only option is to install a fifth (bootable) hard drive into the Apple Mac Pro and this is normally done by installing a bootable SSD drive into one of the DVD-drive bays. Unfortunately if you use a SATA SSD drive (which most SSD's are SATA) and then use one of the two SATA ports on the motherboard to connect it, then you go back to having the problem of not having a boot drive when you boot directly into Windows 8 (since there are no BootCamp 5 drivers for the 2008 Apple Mac Pro that support the two SATA ports on the 2008 Apple Mac Pro motherboard).
This seems to be a never-ending problem, and we have twelve 2008 Apple Mac Pro's (along with an office full of 2008/2009/2010/2013 Apple Mac Pro's) and we're getting extremely frustrated with Apple's lack of support in BootCamp 5.0 drivers for the 2008 Apple Mac Pro (and the two SATA ports on the mainboard).
Please fix this problem, and please update the BootCamp 5.0/5.1 drivers (for 2008 Apple Mac Pro users) and please support the two SATA ports on the Apple Mac Pro mainboard, and please make those two SATA ports on the motherboard bootable and usable in both Microsoft Windows 8 and in OS X 10.8.3 Mountain Lion. Please update the BootCamp 5.0 drivers to support the two onboard SATA ports in Windows 8 (so that my Blu-Ray burner is viewable/usable in Windows 8).

Just as a follow-up, yes it does seem to be possible to get both SATA ports on a 2008 Apple Mac Pro working (in Windows 8).
You need to enable AHCI in Windows 8.
First boot into Windows 8 and then go into the windows registry (regedit) and enable AHCI in your registry.
You can do this by going to the following registry key:
Computer\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\storahci
Set the "Start" Value data to "0" (to enable AHCI in Windows).
After AHCI is enabled in Windows, then reboot your computer and now the SATA drive (connected to the ODD port) should appear in Windows (under devices).
Now the next step is to update your AHCI drivers (in Windows) to the latest Intel drivers, so that your SATA device will actually work (and work properly).
The latest Intel RST drivers can be found here: https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&ProdId=2101&DwnldID=2306 0&ProductFamily=Software+Products&ProductLine=Chipset+Software&ProductProduct=In tel%C2%AE+Rapid+Storage+Technology+(Intel%C2%AE+RST)&lang=eng
Download the 64-bit drivers (if you are running 64-bit Windows).
After you install the latest drivers, and perform a reboot, your SATA drive should now work under windows.
You can find a long detailed thread about enabling AHCI (in Windows 7) here: http://forums.macrumors.com/showthread.php?t=760482
The thread listed above is a bit old/dated (2009?) but it does give detailed step-by-step instructions for those that want to enable AHCI (and get those two onboard SATA ports working in Windows 8 or Windows 7).
I managed to get everything working in Windows 8, and I was able to enable AHCI in Windows 8, installed the latest AHCI drivers and I'm now able to use my SATA Blu-Ray burner in my 2008 Apple Mac Pro.
Hope this helps!
-> Mark

NF750-G55 - Does not detect usb mouse (have to plugin after boot into Windows)

Topic says it all...
Mouse is Microsoft Habu, has been working in my old system just fine (ASUS M2N32-SLI DELUXE). The only usb items plugged in are the mouse and my Logitech G11 Keyboard.
I just upgraded my old rig to what you see in my signature, my mouse will not get detected unless I replug it in after windows has started.
During boot after initializing usb controller it says Found: 1 Keyboard and 1 Hub
I have tried the following but with no successful results:
PS2 Keyboard with mouse (mouse behaves the save)
Mouse w/usb->ps2 adapter (mouse lights up but doesn't do anything in windows)
Mouse plugged into every different port on the MOBO, D-Bracket, front panel usb or even into keyboard
Different mouse (boot says Found: 1 Keyboard, 1 Mouse, 1 Hub) and this mouse works all the time
USB Legacy On/Off inside bios
I also have a USB powered hard drive (http://www.simpletech.com/products/storage/simpledrive-mini/red-wine-250gb.php) that when plugged into the motherboard was making a beeping sound but I can't find any information on what that means (if anything)
Any ideas?

Quote
I just upgraded my old rig to what you see in my signature, my mouse will not get detected unless I replug it in after windows has started.
I had a similar problem with a couple of different boards, but with a Razer Copperhead mouse. I ended up just buying a new mouse (PS/2 type).

System locks about 3min after booting into windows

AMD TB 1.4ghz
512mb Elixer DDR ram
K7N Delta 2 board
430W Power supply (just bought)
WD 80gb HD
Boots up fine then fails shortly after. Just freezes up. I did a memory test on the RAM and no errors. Any ideas?

Quote from: tordavis on 18-September-05, 17:30:27
This same thing was happening with the Asus board and older PSU. New PSU and Board, same issue. On old board it would take a little longer but it would still happen. Especially after loading a sound app like Fruity Loops or iTunes and playing music. I'm starting to think that this old AMD TB1.4ghz cpu just doesn't like the newer boards. I'm thinking maybe I should update the bios?! The latest version is B.5 but my version is so old that it doesn't match current version numbers. Mine is an 11.4.
Discuss?
[EDIT] Noticed something else. If I let the system run for a LONG time after it's frozen and then reboot, I can't even get into bios when I hit delete. Just locks at that point. So turning it off for about 10 mins and rebooting it lets me get into bios. Those are the symptoms of an overheating problem. It's clocking my cpu at the correct 1400mhz at 133fsb. I have it set to auto. Why would it be overheating? Never had this problem with the old asus board. .18 micron tech can't handle the power this board is putting out maybe? I have a nice heatsink and fan on the cpu....this is perplexing. OH and what is that little orange plastic thing underneath where the cpu goes? It sticks straight up. Is it like a cpu thermometer?
Yes, the orange plasitc strip under the CPU is the thermal probe.
I found the 11.4 (B4) BIOS to be the most unstable of all I tested for my components. The B30 (11.3) BIOS tends to be the most stable however the B.50 (11.5) BIOS works best for me in performance.
Take labtech1's advice and try enabling the setting "PRIVATE" in dynamic overclocking because it has been found to stabilize BIOS 11.4 and 11.5

I have recently restored everything on my iMac after getting a new hard drive. When i try to use Elements, i get the following error code ERROR 150:30. Any ideas?

I have recently restored everything on my iMac after getting a new hard drive. When i try to use Elements, i get the following error code ERROR 150:30. Any ideas?

Did you use migration assistant to copy over programs, documents, and settings? You can't do that with PSE. Elements is not a tidy package in accordance with the apple developer guidelines. The installer strews stuff all of your hard drive in place the migration assistant isn't programmed to look and you can never hope to find all h the bits. You must always install PSE from scratch on a new machine. By attempting to copy it you have made a lot of trouble for yourself.
You will need to download and run this:
Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6
and then you can go around and manually remove what you can reach. Look in applications, your hard drive>library>application support>adobe, your username>library>preferences. In the user library also delete any saved application states for PSE.
Then you can reinstall from scratch.

Anybody have problems restoring Iphone 4 for verizon after replacing the LCD

anybody have problems restoring Iphone 4 for verizon after replacing the LCD

i didnt replace the screen on my verizon iphone, but i have had several problems in the past with restoring, however they are always easily solved for me by plugging into another computer and restoring from there once its restored off that computer you can then plug back into your computer and put your info back on.
also remember to copy the ipsw from your iphone software updates folder onto a flash drive and onto the computer you are using to update to save yourself form downloading the ipsw on that computer (if it is not already on that computer). then just do an option restore by holding option key when you hit restore and select the ipsw you want to restore to.
hope this helps

This is making me really mad I have an iPhone 4s and all off a sudden the volume slider disappeared and now it won't let me turn up my volume I have reset restored done the tooth brush trick blew into it and everything an it still wont work someone help!!

This is making me really mad I have an iPhone 4s and all off a sudden the volume slider disappeared and now it won't let me turn up my volume I have reset restored done the tooth brush trick blew into it and everything an it still wont work someone help!!

Is that the only solution? This just happened to me last night and I though that maybe it was just acting up and it would be fine this morning but it wasnt..

Can't boot into Windows 8.1 partition after apple store repair

Can't boot into Windows 8.1 partition after apple store repair
I went to the apple store about a week ago to get my screen fixed, and when I get it back I don't have an option to boot into my windows partition. The bootcamp partition is still there, but I can't boot into it. I can still see all of the files on the drive. When I try to boot into windows from the startup disc setting I get "no bootable device — insert boot disk and press any key” on a black screen. I went in for a dead pixel, and the guy at the genius bar ran something on my computer and went into disk utility application. I’m not sure what he was doing, but obviously that’s what messed up my windows partition. How can I be able to boot back into windows? Here's what disk utility looks like on my computer.

Here's the output
00000000 eb 52 90 4e 54 46 53 20 20 20 20 00 02 08 00 00 |.R.NTFS .....|
00000010 00 00 00 00 00 f8 00 00 3f 00 ff 00 00 b0 0e 2b |........?......+|
00000020 00 00 00 00 80 00 80 00 ff bf 2e 0f 00 00 00 00 |................|
00000030 00 00 0c 00 00 00 00 00 02 00 00 00 00 00 00 00 |................|
00000040 f6 00 00 00 01 00 00 00 05 92 d3 74 c4 d3 74 aa |...........t..t.|
00000050 00 00 00 00 fa 33 c0 8e d0 bc 00 7c fb 68 c0 07 |.....3.....|.h..|
00000060 1f 1e 68 66 00 cb 88 16 0e 00 66 81 3e 03 00 4e |..hf......f.>..N|
00000070 54 46 53 75 15 b4 41 bb aa 55 cd 13 72 0c 81 fb |TFSu..A..U..r...|
00000080 55 aa 75 06 f7 c1 01 00 75 03 e9 dd 00 1e 83 ec |U.u.....u.......|
00000090 18 68 1a 00 b4 48 8a 16 0e 00 8b f4 16 1f cd 13 |.h...H..........|
000000a0 9f 83 c4 18 9e 58 1f 72 e1 3b 06 0b 00 75 db a3 |.....X.r.;...u..|
000000b0 0f 00 c1 2e 0f 00 04 1e 5a 33 db b9 00 20 2b c8 |........Z3... +.|
000000c0 66 ff 06 11 00 03 16 0f 00 8e c2 ff 06 16 00 e8 |f...............|
000000d0 4b 00 2b c8 77 ef b8 00 bb cd 1a 66 23 c0 75 2d |K.+.w......f#.u-|
000000e0 66 81 fb 54 43 50 41 75 24 81 f9 02 01 72 1e 16 |f..TCPAu$....r..|
000000f0 68 07 bb 16 68 52 11 16 68 09 00 66 53 66 53 66 |h...hR..h..fSfSf|
00000100 55 16 16 16 68 b8 01 66 61 0e 07 cd 1a 33 c0 bf |U...h..fa....3..|
00000110 0a 13 b9 f6 0c fc f3 aa e9 fe 01 90 90 66 60 1e |.............f`.|
00000120 06 66 a1 11 00 66 03 06 1c 00 1e 66 68 00 00 00 |.f...f.....fh...|
00000130 00 66 50 06 53 68 01 00 68 10 00 b4 42 8a 16 0e |.fP.Sh..h...B...|
00000140 00 16 1f 8b f4 cd 13 66 59 5b 5a 66 59 66 59 1f |.......fY[ZfYfY.|
00000150 0f 82 16 00 66 ff 06 11 00 03 16 0f 00 8e c2 ff |....f...........|
00000160 0e 16 00 75 bc 07 1f 66 61 c3 a1 f6 01 e8 09 00 |...u...fa.......|
00000170 a1 fa 01 e8 03 00 f4 eb fd 8b f0 ac 3c 00 74 09 |............<.t.|
00000180 b4 0e bb 07 00 cd 10 eb f2 c3 0d 0a 41 20 64 69 |............A di|
00000190 73 6b 20 72 65 61 64 20 65 72 72 6f 72 20 6f 63 |sk read error oc|
000001a0 63 75 72 72 65 64 00 0d 0a 42 4f 4f 54 4d 47 52 |curred...BOOTMGR|
000001b0 20 69 73 20 63 6f 6d 70 72 65 73 73 65 64 00 0d | is compressed..|
000001c0 0a 50 72 65 73 73 20 43 74 72 6c 2b 41 6c 74 2b |.Press Ctrl+Alt+|
000001d0 44 65 6c 20 74 6f 20 72 65 73 74 61 72 74 0d 0a |Del to restart..|
000001e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000001f0 00 00 00 00 00 00 8a 01 a7 01 bf 01 00 00 55 aa |..............U.|
00000200
Here's a better screenshot.

IMac G5 fan always at maximum speed after booting into si...

IMac G5 fan always at maximum speed after booting into single-user mode in 10.4.3
Model: 1.6GHz iMac G5 with 10.4.3
I updated my iMac to 10.4.3, then booted into single-user mode to do some cleaning at the command-line level. I know, as others have discovered, that in single-user mode, the thermal control is off, so the fan gradually increases up to maximum speed and stays there until you reboot or go into multi-user mode. Well, I have never experienced this one before, and I'm freaking out about it... I went into single-user mood one reboot after upgrading to 10.4.3, and after all the println white text lines ended, the [1] fan shot up to maximum speed in 0.35 seconds (it sounded like a high-pitched DJ record scratch during the time interval), [2] the fan stayed at maximum speed when I left single-user mode, and [3] I cannot get the fan to slow itself! I rebooted, shut down, and even tried booting off the Tiger CD, but the instant I hit the power button to turn on the iMac, the fans blast up to maximum speed. They shut down when I put the iMac to Sleep, but then they blast up again in full when it wakes up. I checked my settings in the Energy Saver preference pane, and I have the performance set to "Reduced," which is the lowest possible.
I searched to see if anyone else had this problem or if the KBase had any info, but I didn't see any. I'm thinking about erasing and installing my stuff on the iMac, even though I just did that today.
Again, this maximum speed fan problem is freaking me out. It just started when I booted into single-user mode in OS X 10.4.3. I have booted into single-user mode before (10.4.2) and have not experienced this fan issue. I repeat, the fans blast up to maximum speed after pressing the power switch to turn on the computer, so they do not even wait for the Apple logo to show up on the screen before blasting away. How can I get these fans to not do this anymore?!

for the last few months my 20" 1.8GHz Imac has been very noisy - fans seem to run constantly and noisily. It might have been when updating to Tiger but I was never sure. Today, on the advice of a chat tech, I opened the case and reset the SMU to hopefully cure another problem. I noticed that all the air vents, intake and expel ones, were all quite heavily clogged up - not blocked but clogged with dust and fluff. I cleared it away mainly by blowing but also with a hand held hoover held close by. The exposed fan still as a lot of muck on it but greatly reduced and all the vents are completely clear. Having put everything back together again the iMac has been runnning quietly all day. May have been the SMU reset but equally might just be that the computer couldn'tdraw in cool air, circulate it or expel it properly and the fans had to work overtime to cope. Worth checking if you have noisy fans running at speed constantly.

No reboot after booting into safe mode

For a few years I've just ignored the problem but thought I should take time to mention it now.
When I boot into Safe Mode (holding down the shift key during boot up) I can always click on restart when the password screen comes up and the computers will restart.
But if I log in after safe boot and let the system boot up past the login screen THEN try a restart I get hours of beach ball. I've left various computers running over night and it is always the same in the morning, no restart, no beach but lots of beach ball.
So I do a force shutdown (hold the on/off button for 10 seconds) or a forced restart.
This has been the case from Leopard OSX10.5 and up including Snow Leopard. And on five different Intel Core 2 Duo Macs including 2GHz & 2.4 GHz iMacs and Macbooks.
The common theme is that I have migrated my setup through all these Macs so maybe there is some legacy thing in my software.
Suggestions?

Well… some improvement.
Here’s what I did: (note that I did a restart and sometimes safe boot after each and every step.
1 – use FontNuke (free shareware) to blast away font cache files. It found 8 some dating from 2002.
2 – use Apple’s Font Book to reconcile duplicate fonts.
Those two steps fixed my slow down problems with playing movie files in Quicktime and VLC.
But not Skype video. The biggest CPU load with Skype is with the transmitted picture oddly enough.
Then for good measure I zapped the PRAM and PMU. No noticeable improvement from doing those. Obliviously repair permissions and verify disk was done long long ago and redone.
I still have the problem of not being able to reboot from safe mode.
The Startup folders are clean except for Qmaster which I do not believe is the cause of not being able to reboot out of safe mode.
Does anyone know of other files/locations that put 3rd party startup items? I remember finding things from Western Digital and Symantic a few years ago in unexpected places. Symantic was especially hard to track down and eliminate.

Blue screen - after booting into Darwin/BSD

Hi,
after I had the problem of my iMac G5 only booting into Darwin/BSD (which I posted here: http://discussions.apple.com/thread.jspa?threadID=1093517&tstart=0), I followed the instructions for recreating the user accounts, as described here: http://discussions.apple.com/thread.jspa?threadID=320663&start=0&tstart=0
Now I'm able to get to the blue screen, and the system doesn't exit into Darwin/BSD any longer. However, the Setup Assistant doesn't start either.
I only see an empty blue screen (I guess it's the GUI base screen) and the menu bar. The menu bar only has to items: one menu 'loginwindow', which doesn't have any entries. And the Apple-logo menu, which has the following menu entries:
- About This Mac
- Software Update...
- Mac OS X Software...
- System Preferences...
- Dock >
- Location >
- Force Quit...
- Sleep
- Restart...
- Shot Down...
- Log Out System Administrator...
The 'Restart...' entry doesn't work. I can, however, launch the System Preferences window.
Tail command of /var/log/System.log shows:
configd[41]: WirelessConfigure: 88001003
kernel[0]: Registering For 802.11 Events
kerner[0]: [HCIController][setupHardware] AFH Is Supported
kernel[0]: ATY,Aphrodite2_A: vram [98000000:08000000]
mDNSResponder: Couldn't read user-specific Computer Name; using default bMacintosh-0014513219B8b instead
kernel[0]: ATY,Aphrodite2_B: vram [98000000:08000000}
mDNSResponder: Couldn't read user-specified local hostname; using default bMacintosh-0014513219B8.localb instead
/System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow: Login Window Application Started
loginwindow[141]: [Login.m:1867] Failed to launch /Applications/Server/Server Assistant.app/Contents/MacOS/Server Assistant (error -1)
mDNSResponder: Adding brows domain local.
Any recommendations on what to do next?
Thanks!
Torsten

Apologies, was a little vague. and as far as my profile goes i have loads of mac's here in the studio.
using MBP latest model, Snow Leopard with latest updates.
1. boot up in windows XP SP3 (bootcamp NTFS formatted 32GB partition) - all ok
2. shut down windows and re boot in OSX
3. boots up but fails to complete and hangs on blue screen (just prior to desk top picture loading)
4. press and hold power button to shut down
5. reboot in OSX - boots up fine this time

Screen 'flicker'/artifacts after boot into arch

i experience some sort of flickering/artifacts (dunno how to call it, it's like pixels flying across the screen) after i boot into arch. even when i'm (still) in a tty with no x session running. (before booting into arch, while in the grub menu, it's ok)
it looks pretty much like this.
my gpu is an ati radeon hd4570, i have the free radeon driver (xf86-video-ati) installed.
not sure whether it can be a driver issue though, because it happens even when i'm not in a graphical session?
unfortunately i don't know what to do or what to look at to fix this. investigating this issue i'm led to believe it could have something to do with grub or kernel settings or sth, but i have 0 experience with configuring either.
i'm dualbooting with ubuntu 14.04 btw, which also runs the radeon driver, and i don't have the problem there.
i'd appreciate any sort of help!
(this is my first time posting here, i apologize if i ignored any forum etiquette)
Last edited by weisbrot (2015-02-18 20:49:05)

weisbrot wrote:my gpu is an ati radeon hd4570, i have the free radeon driver (xf86-video-intel) installed.
For Radeon you should use xf86-video-ati, not xf86-video-intel.

Can't boot into Windows after splitting Mac partition with Disk Utility

Hi everyone,
I installed Windows 8 with BOOTCAMP, creating a large 871 GB partition with a smaller 127 GB partition for Windows. After installing Windows, I then went back to Disk Utility to shrink the Mac partition and add two new partitions, one for storage and another blank, hoping to use it to install Linux into one day.
I did that, and now Windows doesn't boot. A Windows blue screen tells me I need to use the Windows DVD to repair it.
I tried to use Disk Utility to delete the two new partitions I made and grow the Mac partition back to the max size of 871 GB. But it doesn't let me do this. The Disk Utility log doesn't report an error and thinks it worked but the partition stays the same size. However if I make the partition a little smaller, like 870 GB then it works. I'm wondering if the Recovery partition is hiding there and preventing me from fully expanding the Mac partition.
What can I do?
Here's what I get if I type in sudo gpt -r -vv show disk0:
Code:
gpt show: disk0: mediasize=1000204886016; sectorsize=512; blocks=1953525168 gpt show: disk0: Suspicious MBR at sector 0 gpt show: disk0: Pri GPT at sector 1 gpt show: disk0: Sec GPT at sector 1953525167 start        size index contents 0           1         MBR 1           1         Pri GPT header 2          32         Pri GPT table 34           6 40      409600      1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B 409640 1701278816      2 GPT part - 48465300-0000-11AA-AA11-00306543ECAC 1701688456     1269536      3 GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC 1702957992     1846360 1704804352   248002560      4 GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 1952806912      718223 1953525135          32         Sec GPT table 1953525167           1         Sec GPT header
Here's what I get if I type sudo fdisk /dev/rdisk0:
Code:
Disk: /dev/rdisk0     geometry: 121601/255/63 [1953525168 sectors] Signature: 0xAA55 Starting       Ending #: id cyl hd sec - cyl hd sec [     start -       size] ------------------------------------------------------------------------ 1: EE 1023 254 63 - 1023 254 63 [         1 -     409639] <Unknown ID> 2: AF 1023 254 63 - 1023 254 63 [    409640 - 1701278816] HFS+ 3: AB 1023 254 63 - 1023 254 63 [1701688456 -    1269536] Darwin Boot *4: 07 1023 254 63 - 1023 254 63 [1704804352 - 248002560] HPFS/QNX/AUX
Here's what I get with gdisk:
Code:
Disk /dev/rdisk0: 1953525168 sectors, 931.5 GiB Logical sector size: 512 bytes Disk identifier (GUID): 6075110F-7CEF-4604-85EE-6231B850E2AE Partition table holds up to 128 entries First usable sector is 34, last usable sector is 1953525134 Partitions will be aligned on 8-sector boundaries Total free space is 2564589 sectors (1.2 GiB) Number Start (sector)    End (sector) Size       Code Name 1              40          409639   200.0 MiB   EF00 EFI System Partition 2          409640      1701688455   811.2 GiB   AF00 1 TB APPLE HDD HTS54101 3      1701688456      1702957991   619.9 MiB   AB00 Recovery HD 4      1704804352      1952806911   118.3 GiB   0700 BOOTCAMP

Okay, the code I typed didn't display properly in the forum. Let me try again.
Here's what I get when I type
sudo gpt -r -vv show disk0:
gpt show: disk0: mediasize=1000204886016; sectorsize=512; blocks=1953525168
gpt show: disk0: Suspicious MBR at sector 0
gpt show: disk0: Pri GPT at sector 1
gpt show: disk0: Sec GPT at sector 1953525167
       start        size index contents
           0           1         MBR
           1           1         Pri GPT header
           2          32         Pri GPT table
          34           6
          40      409600      1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B
      409640 1701278816      2 GPT part - 48465300-0000-11AA-AA11-00306543ECAC
1701688456     1269536      3 GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC
1702957992     1846360
1704804352   248002560      4 GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
1952806912      718223
1953525135          32         Sec GPT table
1953525167           1         Sec GPT header
And when I type fdisk /dev/rdisk0 I get:
Disk: /dev/rdisk0          geometry: 121601/255/63 [1953525168 sectors]
Signature: 0xAA55
         Starting       Ending
#: id cyl hd sec - cyl hd sec [     start -       size]
1: EE 1023 254 63 - 1023 254 63 [         1 -     409639] <Unknown ID>
2: AF 1023 254 63 - 1023 254 63 [    409640 - 1701278816] HFS+
3: AB 1023 254 63 - 1023 254 63 [1701688456 -    1269536] Darwin Boot
*4: 07 1023 254 63 - 1023 254 63 [1704804352 - 248002560] HPFS/QNX/AUX
Kappy,
I can boot into OS X just fine so if possible, I'd like to avoid reformatting everything. If you know of a way I can add more than 2 partitions with OS X and Boot Camp, please let me know. As far as I know, rEFInd can recognize more than two partitions, but I don't think it can edit partitions on a GPT / hybrid MBR system. Or am I wrong?

After i install windows 7 in bootcamp my mac turns off, but i can...

Hello everyone, this problem y very weird.
I installed windows 7 with bootcamp and everytime y try to boot from windows it shuts down my mac. Th weird thing i that i installed parallels 6 in my mac and i can go inside my windows 7 partition.
When i run the windows 7 installer cd and run the trouble shooter its say that maybe i have installed a camera or something like that, remove it and restart, if the problem persists contact apple support.
Hope you can help
Thanks

Look here for a way to do it like a 2011 MBAir is set up for.
If you get it to work it will un-dim the option to create the W7 installer and Boot Camp drivers on the USB drive automatically.
I got it to un-dim for my 2010 MacPro.

After logging into Windows 7, I have to double click several times on Mozilla in order for it to pop up. Then on the tool bar it will show that I have several open boxes of Mozilla.

Mozilla will not open even after several tries. It eventually will but then I have several open Mozilla boxes and have to delete each one until I have just the one.

Just sounds as though you're being impatient. Wait a minute after logging in and then double click the icon. It'll probably then load up straight away.
Each time you double-click an icon it'll launch a new instance of the application. So what you're probably doing is double-clicking 7 times, which then causes 7 copies of FF to open when your computer catches up.

Have to restore OS X.9.1 after booting into Windows 7 on Bootcamp

Similar Messages

Maybe you are looking for