Having challenges with sound

I have sound when using you tube and listening to my music, but have no sound on keyboard, alerts, games etc.... Any suggestions?

Make sure you did not mute the sound. Locate the side switch and move to its unlocked position. Identifying the side switch: The sound is muted when the switch is in its lock position, an orange circle above, and in down position. The sound is not muted when side switch is in its unlocked position, in up position with nothing n the bottom. If your side switch is switched to lock screen rotation, double tap the home screen button, and slide to the left of the multitask bar. Click on the speaker with a sash through it, and it should transform to a regular speaker.

Similar Messages

  • HT1657 I am having problems with sound in my rental movies

    We rent movies all the time but lately we are having problems with sound for our movie rentals.  We watch the first half hour without a problem than the voice is choppy all the time.  Sometimes it is good for five minutes than noting for a while.  We  have tried everything we could think of with no avail.  I could see one movie but the last 5 or so have been the same.  Done trying we need to fix this!  Help!  Any ideas?

    First try resetting your iPad by simultaneously pressing and holding the Home and Sleep/Wake buttons until you see the Apple Logo. This can take up to 15 seconds so be patient and don't release the buttons until the logo appears. Try again to see if the problem persists.
    If you still have the same issue, it's possible that something is lodged in the earphone jack. This can cause the iPad to think earphones are plugged in when they are not. Use a vacuum to try to suck any dust, lint or other foreign matter from the jack. If that still doesn't work, try CAREULLY using a toothpick.

  • I am having trouble with sound on my iPad

    I am having trouble with sound on my iPad

    Found the fix.
    If the reboot doesn't fix it.
    If the headphoens work find, but no external speakers.
    If the double-click and page right to the software mute, doesn't show the sound knob - just the brightness
    If your pop-up shows "Docking Station"
    Then, the problem is very likely a dirty connector.  The iPad/iPhone/iPod connector uses a resistor value to determine if the device is connected to an external 'speaker'.  There are a range of resistances, for a range of products.  This is known as the Connector Pin 21 issue.
    Take some windex on a que-tip, or perhaps a Windex paper scrub and rub it on the bottom connector port.  Somehow, "something" has gotten on those contacts, and it is pulling the voltage on pin #21 down - so that the iPad "thinks" it's connected to an external speaker - this will disable the internal speaker circuitry, as well as the internal speaker volume controls.
    Do not over-saturate and short out your iPad.  Do not throw it in the sink, do not use the kitchen faucet to flush it out.  A Que-tip with a few drops of Windex (or other gentle cleaner) should work just fine.  Takes all of 30 seconds - and magically, the volume knob appeared and everything worked just fine.

  • Can anyone please help me, I'm having problems with sound while watching video clips using flash player using Internet Explorer\

    Can anyone please help me, I'm having problems with sound while watching video clips using flash player & Internet Explorer

    There's a good chance that this is a known issue.  We'll have a Flash Player 18 beta later this week that should resolve this at http://www.adobe.com/go/flashplayerbeta/

  • Having trouble with sound on my iphone 3gs ringtones work but ipod doesnt any ideas?

    having trouble with sound on my iphone 3gs ringtones work but ipod doesnt any ideas? have tried resetting cleaning earphone dock and still not working

    Same here, I get no sound from videos, text messages. This happens for a while, then it works again then it doesn't work. When I go to settings, my "change with buttons" is on but buttons don't work. I have restored it but there is no change. Here is a picture of my screen when i try to change volume.

  • HT204382 Hi, Ive just got myself a Macbook Pro, and Im having problems with sound on movie files. The format is wmv and they play OK on a windows 7 laptop, and Im trying to play them now on the MAC. The picture is OK , but no sound. I have Flip4Mac - no d

    Hi, Ive just got myself a Macbook Pro, and Im having problems with sound on movie files. The format is wmv and they play OK on a windows 7 laptop, and Im trying to play them now on the MAC. The picture is OK , but no sound. I have Flip4Mac - no diference

    Download and install the free VLC for Mac - that should work:
    http://www.videolan.org/vlc/download-macosx.html

  • Help! Having problems with sound on my 4s

    Ive been having problems with the sound on my iphone 4s, it sometimes has a ringtone and has keyboard clicks but it wont play music or have any ringtones or anything. It doesn't even come up with the volume scroll bar or the volume buttons on the side no longer work. This isn't due to liquid damage or anything, this is a software issue. Is there anyway to fix this?

    pheebs273 wrote:
    I It doesn't even come up with the volume scroll bar or the volume buttons on the side no longer work. This isn't due to liquid damage or anything, this is a hardware issue. Is there anyway to fix this?
    If it's a hardware issuem the hardware needs to be fixed.

  • We recently purchased the iphone5 (2) and are having problems with sound coming thru the earbuds when we plug them in to the iphones.  works fine with the ipad.  help please

    recently purchased the iphone5 (2 of them) and are having problems with the earpods.  no sound when plugged in to the iphone.  both phones.  works with the ipad.  help please

    Hi P5052,
    Welcome to the Support Communities ... and congratulations on the purchase of your iPhone 5's!
    It is very unusual that neither phone is working with the new earpods. 
    Have you tried a different headphone just to see if the issue is with the earpods or the iPhones?
    The article below will give you the basic troubleshooting steps for this issue.
    Click on the link below to see more details and screenshots. 
    I've quoted some helpful highlights for you:
    iPhone: Can't hear through the receiver or speakers
    Symptoms
    When someone calls, I can't hear them through the receiver or speaker phone, and I can't hear music through the speaker. I also can't be heard by someone who is calling me.
    Note: iPhone has one speaker, which is adjacent to the dock connector. On iPhone 4 or later models, the speaker is to the right of the dock connector. On earlier iPhone models, the speaker is to the left of the dock connector.
    Resolution
    Verify that there is nothing plugged in to the headset jack, including headsets, headphones, or adapters.
    Make sure the Ring/Silent switch is not switched to silent.
    While on the Home screen, adjust the volume buttons. If you see the icon below, indicating that headphones are attached, there may be debris or an object lodged in the headset jack:
    Check the headset jack. If there is an object lodged in the headset jack that is not easily removed, have the iPhone serviced to remove object.
    For Original iPhone: If there is light debris, such as lint, in the headset jack, try connecting a pair of headphones to the headset jack and then remove the headphones. Repeat this several times to remove the debris.
    If you have installed a protective film on the display, either ensure that the receiver is not covered or remove the film completely.
    Check the receiver mesh (which is on the top front of the device, above the display). If it appears blocked, use a clean, small, dry, soft-bristled brush to carefully and gently brush away any debris.
    If you have paired with a Bluetooth headset that is nearby, either use the headset or turn Bluetooth off (chooseSettings > General > Bluetooth).
    Restart the iPhone.
    If restarting the iPhone doesn't resolve the issue, try restoring the device.
    If the issue persists, go to the Service Answer Center - iPhone for information on service.
    Hope this helps!
    - Judy
    <Edited by Host>

  • Is anyone having issues with sound after upgrading RAM?

    I recently bought a 2009 Mac Mini with 1GB of RAM. Everything was working fine so I decided to upgrade the RAM to make running more apps a little smoother.
    I took it to KRCS (an Apple Premium Reseller) and they put in another 1GB stick. I took the MM home and booted it up but no chime. I loaded iTunes and songs wouldn't play. I couldn't even turn the volume up or down.
    After taking it back to KRCS they verified all the connections were ok and everything was seated correctly, however the sound still wont work. They ran some hardware diagnostics and they said that it is showing that there is a sound devicde present but it isn't showing any input or output devices once booted in to OS X.
    Has anyone else had this problem? Does anyone have any suggestions as to what could be causing this? Could it be a firmware issue do you think?
    Cheers,
    James

    Morning peeps
    As mentioned I booked my Mac Mini in with an Apple Genius to see if they could shed any light on the problem. So I saw a very helpful guy called James (go figure 8-)) who looked first of all looked to see if there were any reported problems by Apple. He also had a look around the net to see if there were any suggestions but unfortunately this all proved to be fruitless. He then tried booting from a clean drive to see if it was a software issue but this again failed, leaving him a little stumped.
    Finally after a few minutes of looking at verious hardware information he decided to look at the RAM as the Mac was reporting the new 1GB stick I had installed was from a different manufacturer. Again no luck and at this point I knew what was comming...
    "It doesn't look like I will be able to fix the problem today."
    After all his efforts he couldn't seem to solve the issue so the next stange involves replacing some of the hardware. He showed me that he had gone ahead and ordered a new sound board, the ribbin that connects it to the main board and something else which escapes me at the moment, all of which is covered under the waranty.
    So after all that the issue still remains. My Mac Mini is at the Apple Store at the moment and is awaiting the new parts to be installed. James was confident that it could be fixed with these new parts, however he did say that if it couldn't be fixed then Apple would replace it with a new one. He also mentioned that they would try and get the RAM upgrade working once the new hardware was fitted, but if that is unsuccessful he is going to give me the RAM back to get a refund at KRCS.
    I think I have covered everything there - sorry if I started to ramble a bit
    If you need any more information then I would be more than happy to help.
    Cheers,
    James

  • Having trouble with sound quality

    I have had this iPod Touch 2nd Generation for almost 2 years now, and I'm starting to have some troubles with it. The headphone sound quality is now starting to deteriorate. Unless the headphones are plugged in a specific way, either one bud goes out, or the sound quality goes down, as there is a lot of static and crackling, and I've had experiences with it actually shocking my ears while I'm listening.
    I have tried a new pair of headphones, and this does nothing.
    My iPod is obviously beyond the manufacturer's warranty, and it's up-to-date with the latest update. Is there anything I can do?

    Sounds like your headphone jack may need replacing.
    Check out the new remodeled MacOSG website! 24-hour Apple-related news & support.
     MacOSG: An Apple User Group  iTunes: MacOSG Podcast  Follow us on Twitter: MacOSG

  • Having Trouble with sound when hooked up to my Car stereo

    I have hooked up my iPod to my car stereo and it sounds horrible. I dont know if the guy that did it, did it wrong but all support is telling me is that to hook it up with the cords i have. Any help from people? thank you

    Does your ipod play through your car speakers.
    Im guessing it does.
    I am rather confident that your problem is solely thanks to the volume not being correctly done. To make it louder, use the car not the ipod.
    Keep the ipod on a low volume.
    Good Luck!

  • I have an i pod and am having problems with sound. When I watch any video on the device with headphones the music is always too loud for the voice meaning i can't hear what is being said. This problem is accompanied with a buzz in some parts of the music.

    When watching a video with my headphones the volume of speech seams very low even when i adjust volume. The speech also tends to make a humming sound in places. When I listen to music humming is sometimes transmitted, but the volume level is normal. The problem is that when the video is playing i can only hear music and humming with the voice too quiet to hear properly. How can I make both volumes balanced? Also. This happens in all music videos.

    - Try cleaning out/blowing out the headphone jack. Try inserting/removing the plug a dozen times or so.
    - Reset the iPod. Nothing will be lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup
    - Restore to factory settings/new iPod.
    - Make an appointment at the Genius Bar of an Apple store. Seems you have a bad headphone jack.
    Apple Retail Store - Genius Bar
    If not under warranty Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
    Apple - iPod Repair price                  
    A third-party place like the following will replace the jack for less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
    Replace the jack yourself
    iPod Touch Repair – iFixit

  • Having issues with sound on my iphone 4s.

    I've double checked settings and the silent switch but still don't have sound for music, apps, alert tones, lock tone etc.  Everything works fine when headphones are plugged in, but with out them the volume buttons don't work.  I'll push the volume button and the sound icon appears but doesn't have any bars to indicate sound volume.  The sound will work for a very short period of time then stop.  When i'm in Pandora or music there isn't an option to adjust the sound, it says no volume available.  To add to my confusion it seems that the sound works just fine if I"m receiving a call, but not for texting or alert tones???!!!  And suggestions to help fix this issue would be much appreciated!

    Same here, I get no sound from videos, text messages. This happens for a while, then it works again then it doesn't work. When I go to settings, my "change with buttons" is on but buttons don't work. I have restored it but there is no change. Here is a picture of my screen when i try to change volume.

  • Having problems with sound quality in my iphone 5 since update

    Since update done my iphone 5 sound has really deterioated

    Hello Tanper
    Check out the articles below, it will provide multiple options for troubleshooting issues with the sound from your iPhone.
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/ts5180
    iPhone: Receiver and call audio quality issues
    http://support.apple.com/kb/ts5196
    Regards,
    -Norm G.

  • Having problems with sound on my ipad esp on apps

    I have an iPad 2 that all of a sudden has stopped having  any sound. I have rebooted my iPad and am wondering if now I just need to restore it? Don't really want to but will if have to
    Thanks for suggestions!!!!

    You can't have a virus on your iPad! Maybe someone hacked your hotmailaccount.
    Change the password of your Hotmailaccount!

Maybe you are looking for

  • Error in transaction iview

    Hi All, I have created a transaction iview for transaction CJ2B. When I click preview button, first screen of transaction opens properly; but when I enter input parameters and try to go to next screen by pressing 'enter' it displays error: <b>Initial

  • Changed Apple ID and now can't reset my iPhone 4

    When I initially bought my iPhone 4, I had my iCloud account associated with a yahoo email address.  Since that time I have switched my iCloud account to a gmail address. The issue is I can't reset my phone because it only recognizes my yahoo address

  • Plot xy graph

    Hi I am just making a simple simulation model in which a result of a formula is the acceleration.  This result I plot it against time.  By integrating the acceleration I obtain velocity and by integrating the velocity I obtain distance.  Those last r

  • Ipad - Security Question

    Hi, My name is Mr McGarrity and i have an apple ipad. I have forgotten the security question answeres and I have tried the reset link so that it emails a reset link to my alternate email but this is not possible for me as the email apple want to send

  • Display session maxL command is hanging

    Hi All, I am using maxL editor in EAS console to execute the display session command.My requirement is to know the number of Active sessions in to a Essbase Application. I execute the following maxL command display session on database <APPLICATION_NA