Having connection issues with my E2500 and my laptop(now with an AE1000).

Ok, here's the story. Just bought and set up an E2500 Router, no problems. Connected my laptop to and everything seemed to be running fine. Here's the problem. The router is on the second floor. When my laptop is under it, 5 bars. When I go one room over, it goes down to two bars. So, I buy the AE1000, connect that and same story. Now a little history on my laptop. It is a Dell insipron 1720 and it was running vista until I upgraded it to Windows 7. I would appreciate any and all advice. THANKS!

The concern is that you are getting poor signals…. Let me know how did you install the Router – means was configured with the help of the Cisco Connect Software or did manual configuration? The concern that you have for that if you have to do the following settings…
If you have configured the Router with the help of the Cisco Connect Software then you have to open that up in which you have installed… There you will be able to see 4 small window screens…
You have to click on “Router setting” window…
Then click on “Advanced settings” button… That will open the Router Setup page then click on Wireless Tab and make the following wireless channel-
For Channel Settings of 2.4 GHz you have to make the Channel Width to 20 MHz only and Channel to 6, 9, 11...
For Channel Settings of 5 GHz you have to make the Channel Width to 20 MHz only and Channel to 40 or 161...
Then check the connectivity…
If you did configure the Router manually then would have opened up the browser and on the address bar would have typed 192.168.1.1 that would have opened the Router setup page… From there you would have done the same steps as above…

Similar Messages

Is anyone else having connection issues with O magazine?

The iPad connects to everything else fine. It can surf the Internet using Safari, it can download apps from the app store, it can also download other magazines but when trying to download the "O magazine", it gives us an error that states "cannot connect to the server please try again". I have tried everything, even called tech support and no one can figure it out. Already deleted all settings and that didn't help either. Is anyone else having this issue?

Try rebooting your router by unplugging it for 15 seconds or so, if it is WiFi connections taht aren't working.

TS1702 Recently my iPad is having connection issues with iTunes and the app store. I always get the message, "Can't connect to iTunes"...can anyone suggest a solution?

I have tried everything. Wifi is working, I can use safari with no problems, I've tried restarting iPad, I've tried signing out then back into iTunes...and a reboot of my iPad. Nothing works!!!! Oh and I checked for updates and everything is up to date.
What is anyone's suggestion??? Need help please!!!

See:
IOS 6 App store crash: Apple Support Communities
Try:
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup
- Restore to factory settings/new iPod.
- Last, make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

Having connection issues with wireless usb adapter

During the day when I'm just surfing the web or watching shows on hulu.com or using NHL game center live my adapter doesn't have any problems staying connected. But at night when I let my torrent client run my, adapter will disconnect and I will have to re-connect to the router manually to fix it.
Is this a problem with my adapter or the torrent client settings? Would a different adapter, either usb or pci-express, fix this problem?
Let me know if you need any more info.
Thanks for any help.

Hi
I'm having the exact same problem .... exporting photos from iphoto to Facebook had worked perfectly fine for years, then I tried to export some photographs just a couple of days ago and I get the same problems as the Original Poster.
I'm on Snow Leopard (OSX 10.6), iphoto 6 v6.06.
I've tried updating my Adobe Flash player, to no avail.
I'm pleased that other people are experiencing the same problems, but it's a mystery as to why it's suddenly stopped working.
When I was in work I was able to upload photos to Facebook that were saved on my desktop no problem - work uses Windows. But I'm unable to even go to Facebook, click on Create an Album and take it from there ... when I click on Create an Album nothing seems to happen.
I'm so frustrated.

IPhone4 having connectivity issues with Infiniti FX

I am able to make and receive calls sometimes. I need to make and receive call all the time. Is anyone out there have the same issues? Lets say I make a call from my car. The phone icon shows up on the screen in my car, but nothing rings or connects and if it does connect it loses connectivity. I have 3 days to figure this thing out before I to return the **bleep** thing.

suewheatt wrote:
I am able to make and receive calls sometimes. I need to make and receive call all the time. Is anyone out there have the same issues? Lets say I make a call from my car. The phone icon shows up on the screen in my car, but nothing rings or connects and if it does connect it loses connectivity. I have 3 days to figure this thing out before I to return the **bleep** thing.
I see that no other forum members have addressed your device connectivity post. For Bluetooth compatibility with your car, please contact your car's manufacturer as they will be able to confirm what Bluetooth devices are compatibility with your car.
For Bluetooth troubleshooting guides please visit the links below:
http://support.apple.com/kb/HT1843
http://support.apple.com/kb/HT1664

I'm having connection issues with iChat

Every time I try to sign on, I keep getting "iChat Connection Alert: Lost connection with AIM; The connection to the host was unexpectedly lost." It's been like this for awhile now. What can I do to fix this?

i just changed my port to 443 after checking another post and it fixed the problem!

Connectivity issue with ipad 3

anybody having connectivity issues with new ipad 3?
mine won't connect to wifi.
when i switich to cellular 4g lte, that doesn't connect as well.
my macbook pro and iphone connect, with no prob.
i get various can't connect to server messages.
took to genius bar, we erased and rebooted, it worked for a bit but happening again. genius bar staff claimed it was a corrupted file, but i think its more than that?
any thougths?
many thanks,
-L

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
 Cheers, Tom

I have a Blackberry 8330 and a MacBook. For some reason I started having connectivity issues. The handheld will not sync with the computer via pocketmac. I have uninstalled, etc 15 times. Please help

I have a Blackberry 8330 and a MacBook. For some reason I started having connectivity issues. The handheld will not sync with the computer via pocketmac. I have uninstalled, etc 15 times. Please help

Hi Peter!
I'm sorry to read that you are having issues with your Sync account.
Your best bet is to follow the steps described in this blogposts and open a bug:
https://philikon.wordpress.com/2011/06/13/how-to-file-a-good-sync-bug/
After that, if you don't want to user Sync in your computer, you can stop it with this simple steps:
* At the top of the Firefox window, click on the Firefox button (Tools menu in Windows XP) and then click Options.
* Once the options window opens, click on the Sync tab.
* At the bottom of the Sync tab click on '''Deactivate this Device''' link

Im having massive issues with my email... I cant receive emails for my work email... was working perfectly and now just wont connect, i assume that I need to use my home wifi as the outgoing server?? Please help :)

Im having massive issues with my email... I cant receive emails for my work email... was working perfectly and now just wont connect, i assume that I need to use my home wifi as the outgoing server?? Please help

For your work email, do you use a well known server or do you use their own server? Their server IMAP and SMTP addresses might of changed or you entered them in wrong. It might be something with your router but unless you blocked every incoming connection, then it should work. I would talk to your tech guys at work to see if it is on their end.
Hope this helped a bit, Sean

I am having an issue with my iphone4s. It will no longer connect to wifi.

I am having an issue with my iphone4s. It will no longer connect to wifi. The wifi icon is grey and cannot be turned on. How can this be rectified?

A simple search of google or the forums would have revealed http://support.apple.com/kb/TS1559

I am having strange issue with my apple tv...i set up pictures to scroll through to the tv using home sharing. Now album covers are interspersed with my pictures. I have been using apple tv for a while and never had this happen before

I am having strange issue with my apple tv...i set up pictures to scroll through to the tv using home sharing. Now album covers are interspersed with my pictures. I have been using apple tv for a while and never had this happen before

Are you watching this content though iCloud or though from iTunes on your local computer? If it is from iCloud have you tried downloading the content to iTunes and watching it on ATV from that source to see if it still happens? This is geerally a much more reliable way to view the content. Easer to fast forward and rewind too.
- I have a stable internet connection
Clearlly you don't
>(Ive tested on other devices)
Which does not tell you anything about the specific connnection from ATV to iCloud.
>I am able to stream Netflix problem free from my AppleTV without so much as a hicup
Again which does not tell you anything about the specific connnection from ATV to iCloud.
>- I am able to download the episodes to my phone, ipad, and computer without any issues
Again which does not tell you anything about the specific connnection from ATV to iCloud. It does remove your ISP throattly traffice as a possible cause though. So that is good.
Have you checked your wireless rounter? Tried doing the factory restor on it? Upgrading it's firmware? Is it and or ATV getting extreamly hot when this problme happens?

Anyone else having repeated wifi connectivity issues with the OSX version 10.8.5?

I just updated the software on my iMac to OS X version 10.8.5. Now I am having repeated connectivity issues with the wifi in my house. This is the only device that is having these issues. My phone, ipad and tv are not having any problems at all.
It happened immediately following the update. I was sending emails and browsing before the update without a problem.
from apple:

I had a message like that last week - only it asked what browser I would be using - I just quit safari - purges caches etc - and at that time noticed I was getting RSS feeds through PUBSUB - tracking them down to the top sites view I never use - I deleted all of the top sites (most of which I don't go into so it must have been a preset) that included MSN and Google - I don't use google so that was pointless. (deleting a top site means you are blocking it from that page) Have not had the message since so it must have had something to do with top sites activity.
Just a note: Did see somewhere probably BBC tech - that Google was going to stop supporting older web browsers.

Hi, i am having an issue with a basic motion scroll effect. I already watched and read every tutorial out there regarding this topic and even tried the adobe chat support, but the guy on the other end of the line disconnected me-, probably he didn't unde

Hi, i am having an issue with a basic motion scroll effect.
I already watched and read every tutorial out there regarding this topic and even tried the adobe chat support, but the guy on the other end of the line disconnected me…, probably he didn't understand what i wanted from him because english is not my native language, so a will try to be very, very clear about this one..
please note, that i am new to muse, this is my first project ever.
my idea is as following:
when the customer comes to our companies site, he just sees our logo on a white Background. the logo consists of, say, four elements. when the customer scrolls down, the logo starts to disassamble: first the first part of the logo flies out the left side of the site, then the second part of the logo vanishes down, then the third part of the logo flies to the right, then the fourth part of the logo flies to the top and out of the customers view. given what i have seen, it is possible to do that….
so…..
now i have the four parts of my logo imported as png files into muse and assembled them in design view to build our companies logo. I select every one of the four parts and go into the scroll effects tab left beside the layers tab. first i enter the same values for every one of the four parts: initial motion: 0x and 0x again for the left and right motion; key position ( t-handle) : 0px; final motion: 0x and 0x again for the left and right value.
now i hit "preview".: the logo is "pinned" at the correct position, i can scroll but the logo stays where it is. so far so good….
now i select all the four elements again and go to the scroll effecs tab. at "final motion", i click the down arrows and enter 1x. I hit Preview…
when i am scrolling down the WHOLE logo goes down…. so far so good.
NOW i want the first part of the logo to go down, THEN the second part to go left, THEN the third part to go up, THEN the fourth part to go right.
so i select ONLY the first part, go to the scroll motion tab, at "final motion" i click the left arrows, then i enter 1x.( the up-down value, i set to 0 again).. i hit Preview…
the first part of the logo goes left as soon as i start scrolling, the other three parts still go down at the same time…
NOW i want the second part of the logo to start moving, when the first part has left the scene, not at the same time as the first part.
SO I SELECT THE SECOND PART AND DRAG ITS T-HANDLE (KEY POSITION) DOWN TO, LETS SAY, 200PX. SO IT STARTS MOVING ONLY AFTER THE CUSTOMER HAS REACHED THAT POINT, RIGHT?
BUT WHEN I PREVIEW THAT ****, THE LOGO IS NOT TOGETHER ANYMORE, THE SECOND PART IS FLOATING ANYWHERE ELSE BUT WHERE IT SHOULD BE…..WTFF????
short: when i move the t handle, the initial position of the object changes. thats what i said to the adobe employee, but he said, that thats the expected behavior….
but if thats so, how can i have my four parts correctly together, so they form my logo, but with different t handles, so that they all start to move at different times??
Pleeease help me, i am dying of frustration here…..:( that behavior cant be right, right?
Thanks so much to everyone who actually reads this post and tries to help…….
All the best,
Niki Lapan

Thank you so much for helping,
But i really wonder how you did that. did you always switch between design view and preview view, then change the key position for 2px then switch back, to align the four letters? because i imagine that can get really frustrating, if you have a logo consisting of 58 parts instead of 4!:)
Anyway thank you very much for your time and effort!!!!

CR2008 connectivity issue with BOE Universes(sap and non sap universes)

Hi Experts !!
Recently we tried to build/connect to a Universe in Crystal Reports2008 via 'Make a new connection tab'.
The universes are of SAP BW or non SAP Lying in BOE Servers and we are trying to build reports on them by conncting/utilizing the universes as a database for Crystal Reporting.
Our issue is most of the time we are not able to connect to the Universes and the connectivity blows out by some 'communication Error' thing initially.
While at some other points in time, the connectivity takes us to the Universe and we are able to select few characteristics and key figures from the Universe but the moment we go futher and try to run by pressing 'OK' button it blows out and say' LOGON FAILED'.
Apparantly, it is an connectivity issue with BOE server and from the different blogs it looks like it is a known issue for long.
The proposed issue resolution were like either CR2008 should be SP2 with BOE SP3 or there should be some additional .dll files defined in the paths in case of MSSQL database. None of this applies to us as we are on CR2008 with SP3 and going back to SP2 is probably not a viable option for us, and we are using Oracle as underlying database in this specific case.( i would like to tell you here that we are able to connect to Oracle Database directly though).
We have raised a message with SAP and was just wondering if we do have some solution/workaround already available to this known issue in place please?
Thanks&Regards.
Edited by: AMIT GHILDYAL on Aug 1, 2011 2:41 PM
Edited by: AMIT GHILDYAL on Aug 1, 2011 2:44 PM
Edited by: AMIT GHILDYAL on Aug 1, 2011 3:14 PM

Hi Amit,
Moved to Universe Forum.
If you have a case logged then no point posting here also, this is a public site and not a case management tool.
Once you do get the solution from your case please post it here also to help others if they have the same problem.
Thank you
Don

How can I recover an old/disused iCloud account. I was having some issues with my apple id so I restored my iPad, I am now stuck on the activation screen as I no longer use the iCloud account i used to set up the iPad and can't remember the address or pas

How can I recover an old/disused iCloud account. I was having some issues with my apple id so I restored my iPad, I am now stuck on the activation screen as I no longer use the iCloud account i used to set up the iPad and can't remember the address or pas

I have the same problem - it is maddening. I rely on this iPad for work so this is not just an annoyance! The above solutions of changing the appleid on the device or on the website do not work.
The old email address no longer exists - I haven't used it in a year probably and I no longer have the account. I logged into the appleid website and there is no trace of the old email address so there is nothing that can be deleted or changed there. On the iPad there is no trace of the old email address so nothing can be deleted there either. I have updated the iPad software and the same problem comes right back. Every 2 seconds I am asked to log in using the old non-existent email. The device is currently useless.
The only recent change to anything was the addition of an Apple TV device, which was set up using the correct login and password.
Does anyone have any ideas? The iPad has been backed up to the iCloud so presumably it now won't recognize the current iCloud account? So restoring may notbe an option?

Having connection issues with my E2500 and my laptop(now with an AE1000).

Similar Messages

Maybe you are looking for