Having problem connecting to NI-9188

Hi,
I am not able to make connection between NI-9188 Chassis and my Windows 7 Laptop.
My firewall is off.
I have Automation expolrer.
Please suggest what needs to check.
Thanks
Prashant
Solved!
Go to Solution.

Hi Prashant-
I might suggest a couple of troubleshooting steps:
You mention that your cDAQ-9188 is connected directly to your PC.  I assume this means you are using either a normal or crossover ethernet cable (either should be fine) and not a switch, router, or other existing network infrastructure.  For the PC, which settings are you using to establish an IP and associated settings (DHCP+Link-Local, also known as 'Obtain and IP address automatically', or are you setting a static IP directly)?  Please connect the device, wait a couple of minutes, and then execute 'ipconfig' at the command line and post the output here.
If you are using Link-Local addressing and have multiple NICs installed in your computer, it may be possible that the routing table is sending and/or receiving traffic across interfaces.  Please post the output of 'route print' after your 'ipconfig' output.  After that, try disabling other NICs in your system to see if that helps.
Can you locate the device using other mDNS browsers like NI's Network Browser (installed with DAQmx) or with Apple's Bonjour browser (if you have it installed)?  We have seem some very isolated cases where the device locating service in MAX fails but other mDNS browsers are successful.  Which version(s) of DAQmx and/or LabVIEW do you have installed?  What happens if you try to add the device manually by right-clicking on Network Devices in MAX?
EDIT: I just noticed from your earlier post that you are using LabVIEW 2011 and DAQmx 9.2.2.  It seems unlikely that updating DAQmx will help with this specific issue, since LabVIEW 2011 already installs the newest released versions of MAX and its underlying components.  But, while you're still in the getting started stage on this project, you should consider updating to the newest release of DAQmx just to make sure you have any other bugfixes that affect cDAQ in general.
Tom W
National Instruments

Similar Messages

  • I am having problems connecting to home wifi.  It was working, but now all I get is a blank white screen.  I re-booted with no success.

    I am having problems connecting to home wifi.  It was working, but now all I get is a blank white screen.  I re-booted with no success.

    Hi, blank white screen where exactly?
    Make a New Location, Using network locations in Mac OS X ...
    http://support.apple.com/kb/HT2712
    10.5, 10.6, 10.7 & 10.8…
    System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
    10.5.x/10.6.x/10.7.x/10.8.x instructions...
    System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
    The interface that connects to the Internet should be dragged to the top of the list.
    If using Wifi/Airport...
    Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
    For 10.5/10.6/10.7/10.8, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
    208.67.222.222
    208.67.220.220
    (There may be better or faster DNS numbers in your area, but these should be a good test).
    Click OK.

  • Having problems connecting a late 2011 Macbook Pro 2.2ghz i7 to a Sony KDL-32L5000 using a display miniport to DVI adapter (DVI to VGA cord). The TV is not detecting the macbook. Anyone have this problem?

    Having problems connecting a late 2011 Macbook Pro 2.2ghz i7 to a Sony KDL-32L5000 using a display miniport to DVI adapter (DVI to VGA cord). The TV is not detecting the macbook. Anyone have this problem?

    You really have to mess with the resoluton, espescially the refresh rate, as it varies from projector to projector, monitor to monitor. Even within the same brand! Because so many manufacturers are trying so many different things to become the next cool kid on the block, and the way the formats are being configured that's now part of the game.
    That's why so many professionally produced corporate shows hire a dedicated projectionist for the video presentations. Too many bugs in the honey.
    Refresh & sesolution are the first things to look at.
    Just so you know that colors in PowerPoint PC, and PowerPoint Mac, don't exactly match... go figure.
    I forgot to mention another thing, sometimes it's the projector that needs to be tweaked.

  • Having problems connecting MacBook Pro 2010 TO vizio 60 " tv

    having problems connecting MacBook Pro 2010 TO vizio 60 " tv using mini displayport to VGA adapter
    non support warning appears pn tv monitor

    However, I still don't get a view of anything on the desktop except for the standard Apple swirl.
    Can you drag windows to the other display?
    In the "Arrangement" tab of "Displays" system preference, you can drag the display pictures to match the actual arrangement, drag the menu bar to the other display, or enable mirroring.

  • Having problems connecting iMac(late 2006) running 10.7.5 to a Samsung Flat Screen TV using separate audio/speaker cable and HDMI standard cable, mini-DVI to HDMI video converter.  TV displays generic Apple galaxy background and "some" windows (e.g. scree

    Not sure that I have selected the correct forum.  Hope my questions are clearly stated.
    Having problems connecting iMac(late 2006) running 10.7.5 to a Samsung Flat Screen TV using separate audio/speaker cable and HDMI standard cable, mini-DVI to HDMI video converter.  TV displays generic Apple galaxy background and "some" windows (e.g. screen resolution choices).   It does not show Mail or Safari menus.  System preferences'  display "gathered" the Samsung and chose its resolution.  I did not find a way to select the Samsung as my display.
    In addition to having old hardware, we have Verizon FIOS providing internet and TV access.  Is there any way to make this work for us?  We would like to stream video (Netflix) and view shows from the Web.  Do we need Apple TV to do this?  Or is it not possible with our old iMac?  My husband thinks that our Airport could be a factor. 
    Thank you

    Lately, I have been seeing a lot of posts with users trying to use their Macs/iMacs to mirror their streaming video from their Macs to an HDTV.
    There are, actually, many alternatives to choose from than just from a Mac.
    You need to have or invest in a WiFi capable router for all of these examples.
    Apple TV only integrates with WiFi and newer Mac hardware. So, if you want to have total integrated experience, if you have a 2011 Mac or newer, you might as well pay the $100 for the AppleTV box.
    If you have a older Mac, like I have noticed many users do, then you have other options.
    If you want to elimate long cable clutter and having your Mac at the mercy of your TV all of the time,  you can still use the AppleTV box independently or purchase cheaper alternative media streaming boxes from Roku, Sony, Boxee or any number of electronics manufacturers that now have media streaming boxes and media streaming capability built into DVD/Blu-ray players.
    These eliminate long cable clutter by being close to the HDTV where shorter, less expensive cables can be used.
    Another alternative for iPad users is to use an iPad with the USB/HDMI video adapter and use your iPad as the streaming box. This ties up your iPad in much the same way as it does with your Mac, but again the iPad can be close to the TV and use minimal cables to the TV.
    Another alternative to is to use a combination of an iPad and your Mac to stream content that is only available to stream online from a computer. In this case, you can use a desktop remote app on your iPad and Mac. A good and cheap Desktop Remote app is Splashtop Remote. This allows you to completely connect your iPad remotely, over Wifi, to your iMac desktop. The app streams both video and sound to the iPad which is still connected to your HDTV. The resultant stream video picture will be smaller than the size of your HDTV, but it will still be plenty large enough to watch. Again, if you own a iPad and an Intel Mac, this method also allows minimal cabling to the TV.

  • TS1317 Having problem connecting wi-fi to my Mac pro.  Followed all the steps.  Any suggestions of what I can try next?

    Hi, Having problem connecting my Mac Pro to Wi-Fi.  Followed all the steps.  Any suggestions?  Thanks.

    Hi Sandra,
    Have you tried this?
    Instead of joining it from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.

  • This past month I have been having problems connecting to my home wireless connection. Previously I had no problems whatsoever. I have tried unplugging the wireless router, turning off the wirless airport, deleting the network name from my list of server

    This past month I have been having problems connecting to my home wireless connection. I have a MacBook Pro OSX Version 10.6.8. Previously I had no problems whatsoever. I have tried unplugging the wireless router, turning off the wirless airport, deleting the network name from my list of servers and trying to reconnect this way. These methods have worked temporarily, but the same problem keeps coming back. Most of the time my personal wireless connection does not even come up among the list of available networks. My fellow flatmates have PCs and both of them are able to connect to the network without problem.
    The router is a d-link model DIR-615. I am not tech savy, so if any other information need to be provided in order to better understand my situation, please let me know.
    Please help me!

    If I open the list of networks in a window it says "connection timeout," but if I just select it from the drop down it tries for awhile and then stops with no prompt. When I try to run network diagnostics it says "sorry, we can't connect to the internet" (or some solution-free variation of that)

  • I am having problems connecting to 3g after updating to ios 6.1 (iphone 5, 32gb, black)

    i am having problems connecting to 3g since i updated my iphone to ios 6.1, the update 6.1.2 didnt solve the problem, i am having problems connecting to 3g, my phone only shows the symbol E

    I'm having problems too. It eventually connects to 3G but it takes a long time. Try keeping the "Enable 3G" on (if you have the switch) and see if it changes to 3G at some point.

  • Hi I am having problem connecting my mac and iphone6 through AirDrop

    HI I am having problem connecting my mac and iphone6 through Air Drop

    You don't give any information about your Mac but note the quote below which states that it must be a 2012 or later model with Yosemite installed. The quote is from Mac Basics: AirDrop lets you send files from your Mac to nearby Macs and iOS devices - Apple Support which also contains some other things that may help.
    In order to transfer files between a Mac and and an iPhone, iPad or iPod touch
    your iOS device needs to include a lightning connector
    your iOS device needs iOS 7 or later installed
    your Mac needs to be a 2012 or later model with OS X Yosemite installed
    Your Mac and iOS device both need bluetooth and Wi-Fi turned on. You do not have to be connected to a specific Wi-Fi network.

  • Hi i am having problems connecting to internet using ethernet,in the network diagnostics i get all green,except network settings which is orange.i am running mountain lion on intel imac

    hi i am having problems connecting to internet using ethernet,in the network diagnostics i get all green,except network settings which is orange.i am running mountain lion on intel imac

    hi have done as you said plug ethernet straight into computer and into back of router,and worked straight off,i had the the powerline on extention when imac was up stairs,when i had computer down stairs it still would not work with powerlines even on main wall sockets,so they are getting binned,looks like i will have to move router upstairs,just wondering if i got extention wire from back of openreach box to router upstairs```,would it be ok,,the openreach box is next to my only phone socket in house,which is in back kitchen..any advice would be great,

  • HT201269 I am having problem connecting my iphone 4 Bluetooth with my Sony Viao Net Book and other iphones or other bluethooth enabled devices.

    Having problem connecting my IPHONE 4 with my Sony Viao Net Book and other Bluetooth enabled Devices and would also need information about Syncing.

    Have a look here for Supported Bluetooth Profiles
    http://support.apple.com/kb/HT3647
    SYNCING with iTunes
    See here  >  http://support.apple.com/kb/HT1386
    From Here  >  http://www.apple.com/support/iphone/syncing/

  • Just had a replacement iPhone but having problems connecting to iCloud, any tips?

    Just had a replacement iPhone but having problems connecting to iCloud, any tips?

    What problems?
    When you create your iCloud account with the iPhone's Mail app, the settings are not confirmed?

  • TS4006 i am having problems connecting to wifi at home , i want to do a master reset but cant save to icloud without using wifi ?? any ideas ??

    i am having problems connecting to wifi at home , i want to do a master reset but cant save to icloud without using wifi ?? any ideas ??

    If you can't perform an iCloud backup (which requires wifi), back up to your computer with iTunes.  Connect your phone to your computer, open iTunes, click on the name of your phone in iTunes, go to the Summary tab of your iTunes sync settings and click Back Up Now.
    To troubleshoot your wifi, try unplugging your wireless router for 15 seconds, the plug it back in.  Then go to Settings>General>Reset and tap Reset Network Settings (note: this erases passwords for previously joined networks).  Then rejoin your wifi and see if it works properly now.

  • Having problems connecting Coldfusion10 with sql server express 2012

    Hi,
    I am having problems setting up a datasource for a local sql express 2012 server. Its running as the default instance. Connections are working with ODBC and client told just not Coldfusion.
    When I try to set up a connection using the sql driver I get this error:
    Connection verification failed for data source: Leaf
    java.sql.SQLNonTransientConnectionException: [Macromedia][SQLServer JDBC Driver]Error establishing socket to host and port: 127.0.0.1:1433. Reason: Invalid argument: connect
    The root cause was that: java.sql.SQLNonTransientConnectionException: [Macromedia][SQLServer JDBC Driver]Error establishing socket to host and port: 127.0.0.1:1433. Reason: Invalid argument: connect
    When I try a Socket connection with an ODBC connection I setup in windows I get this error:
    Connection verification failed for data source: LeafDB
    java.sql.SQLException: [Macromedia][SequeLink JDBC Driver]Internal network error, connection closed.
    The root cause was that: java.sql.SQLException: [Macromedia][SequeLink JDBC Driver]Internal network error, connection closed.
    Any ideas?
    Thanks,

    Hi Rossco199,
    The issue is likely caused by you not having yet assigned port 1433 in SQL Express itself. Follow the procedure described on the following page, and you should solve the problem: http://www.tensixconsulting.com/2012/02/sqlserverexception-the-tcpip-connection-to-the-hos t-port-1433-has-failed/
    In particular, remember to assign port 1433 to 127.0.0.1 and to IPAll. Also set 'Active' and 'Enabled' to 'Yes' for the IP 127.0.0.1. While you're at it, if 'Named Pipes' is disabled, you should right-click on it and select 'enable'. Afterwards, restart the Windows service 'SQL Server(SQLEXPRESS)'.
    It is advisable to allow ColdFusion server authentication. However, the SQL Express server is configured by default to allow only Windows authentication. This conflict may lead to errors.
    Should you then encounter the dreaded Error 233: "No process is on the other end of the pipe", proceed as follows. Open the tool Microsoft SQL Server Management Studio. Right-click on the name of your database server, then on Properties. In the user interface that opens, click on Security. Select the combined 'SQL Server and Windows Authentication mode'. Restart the service 'SQL Server(SQLEXPRESS)'.

  • Having problems connecting wireless?

    Hi All,
    I just got my MACBOOK two days ago and having some issues connecting wireless.. I can connect to my LINKSYS wireless router but it seems after about 7 mins of use I can no longer connect to the router. I have reset the router and even changed it but I still seem to have the same issue.
    If I use only PC's on my wireless network I don't have any issues.. It seems like the MAC messes up my network and it will not work again unless I take the power out of the router and then modem.
    I have used my comp at a friends house connecting to their linksys router without any issues.
    ANY IDEAS?
    THANKS

    If you have no problems connecting wirelessly on another network, then I'd look at your router as the probably culprit. Do you have any problems connecting to the router by Ethernet cable? Are your Network preferences configured properly? Have there been any firmware updates released for your router that you have not installed? Have you tried a different router in your home network? For example, try a D-Link DI-524. I've had good success with it. I've never had a really satisfactory experience with LinkSys, but that's my personal experience.

Maybe you are looking for

  • UD made but inspection lot quantities in WM are wrong

    On the same day, we received two shipments of the same batch of material from a vendor.  Inspection Lot A  = 119cs.  Inspection Lot B = 13cs.  A total of 132cs. BEFORE materials actually were placed in WM bin locations, our Quality Group instructed t

  • Mapping with attachments, DataType creation

    Hi all, Have to solve two problems: 1. How to map attachment? - I'm getting message with an attachment on XI, then I need to extract it and convert to base64 string(guess it will be done with java mapping, but I don't know how at all). 2. I'm trying

  • Using externally generated pixmap in Canvas

    I am evaluating how difficult it would be to use an external library for drawing images in LabWindows. The library comes with binaries only that were generated in MS Visual Studio, so I assume they can be linked loaded into LabWindows. Are there like

  • Make execute privileges on a package default to all schemas

    I have to grant execute privileges on dbms_aq package to schemas created in our database. Instead of granting these privileges explicitly after a schema is created is there a way to make dbms_aq to be executable for all schemas and any new schemas cr

  • External swf size issue

    Hai.... how get swf width and height using loader ,we are getting different values .... // Fla document size is 550 X 400,but we are getting 500 X 375... <s:WindowedApplication xmlns:fx="http://ns.adobe.com/mxml/2009"