Having Problem With Network
Hi,
I'm having problem with a carrier network (Maxis),which i always get 'no service',whether i on the phone and after i off the phone.I try to reset the network,but it seems the same.Please help me solve my problems.
did u have this problem before of after the last update.
Similar Messages
-
Having problems with networking, seems to be DHCP
I'm having issues with networking on a newly installed Arch Linux instance.
Relevanct lspci data
25:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
26:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 06)
Network manager output
NetworkManager[2201]: <info> NetworkManager (version 0.9.8.2) is starting...
NetworkManager[2201]: <info> Read config file /etc/NetworkManager/NetworkManager.conf
NetworkManager[2201]: <info> WEXT support is enabled
NetworkManager[2201]: <info> Loaded plugin keyfile: (c) 2007 - 2010 Red Hat, Inc. To report bugs please use the NetworkManager mailing list.
NetworkManager[2201]: keyfile: parsing MagnificentBumrag ...
NetworkManager[2201]: keyfile: read connection 'MagnificentBumrag'
NetworkManager[2201]: <info> monitoring kernel firmware directory '/lib/firmware'.
NetworkManager[2201]: <info> rfkill3: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:1c.3/0000:25:00.0/ieee80211/phy0/rfkill3) (driver ath9k)
NetworkManager[2201]: <info> rfkill1: found WiFi radio killswitch (at /sys/devices/platform/hp-wmi/rfkill/rfkill1) (platform driver hp-wmi)
NetworkManager[2201]: <info> WiFi hardware radio set enabled
NetworkManager[2201]: <info> WiFi enabled by radio killswitch; enabled by state file
NetworkManager[2201]: <info> WWAN enabled by radio killswitch; enabled by state file
NetworkManager[2201]: <info> WiMAX enabled by radio killswitch; enabled by state file
NetworkManager[2201]: <info> Networking is enabled by state file
NetworkManager[2201]: <info> (wlo1): using nl80211 for WiFi device control
NetworkManager[2201]: <info> (wlo1): driver supports Access Point (AP) mode
NetworkManager[2201]: <info> (wlo1): new 802.11 WiFi device (driver: 'ath9k' ifindex: 3)
NetworkManager[2201]: <info> (wlo1): exported as /org/freedesktop/NetworkManager/Devices/0
NetworkManager[2201]: <info> (wlo1): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
NetworkManager[2201]: <info> (wlo1): bringing up device.
NetworkManager[2201]: <info> (wlo1): preparing device.
NetworkManager[2201]: <info> (wlo1): deactivating device (reason 'managed') [2]
NetworkManager[2201]: <warn> failed to allocate link cache: (-10) Operation not supported
NetworkManager[2201]: <info> (enp38s0): carrier is OFF
NetworkManager[2201]: <info> (enp38s0): new Ethernet device (driver: 'r8169' ifindex: 2)
NetworkManager[2201]: <info> (enp38s0): exported as /org/freedesktop/NetworkManager/Devices/1
NetworkManager[2201]: <info> (enp38s0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
NetworkManager[2201]: <info> (enp38s0): bringing up device.
NetworkManager[2201]: <info> (enp38s0): preparing device.
NetworkManager[2201]: <info> (enp38s0): deactivating device (reason 'managed') [2]
NetworkManager[2201]: <info> Added default wired connection 'Wired connection 1' for /sys/devices/pci0000:00/0000:00:1c.5/0000:26:00.0/net/enp38s0
NetworkManager[2201]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring...
NetworkManager[2201]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring...
NetworkManager[2201]: <info> (wlo1) supports 4 scan SSIDs
NetworkManager[2201]: <info> (wlo1): supplicant interface state: starting -> ready
NetworkManager[2201]: <info> (wlo1): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42]
NetworkManager[2201]: <warn> Trying to remove a non-existant call id.
NetworkManager[2201]: <info> (wlo1): supplicant interface state: ready -> disconnected
NetworkManager[2201]: <info> (wlo1) supports 4 scan SSIDs
NetworkManager[2201]: <info> (wlo1): supplicant interface state: disconnected -> inactive
NetworkManager[2201]: <info> (enp38s0): carrier now ON (device state 20)
NetworkManager[2201]: <info> (enp38s0): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40]
NetworkManager[2201]: <info> Auto-activating connection 'Wired connection 1'.
NetworkManager[2201]: <info> Activation (enp38s0) starting connection 'Wired connection 1'
NetworkManager[2201]: <info> (enp38s0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
NetworkManager[2201]: <info> Activation (enp38s0) Stage 1 of 5 (Device Prepare) scheduled...
NetworkManager[2201]: <info> Activation (enp38s0) Stage 1 of 5 (Device Prepare) started...
NetworkManager[2201]: <info> Activation (enp38s0) Stage 2 of 5 (Device Configure) scheduled...
NetworkManager[2201]: <info> Activation (enp38s0) Stage 1 of 5 (Device Prepare) complete.
NetworkManager[2201]: <info> Activation (enp38s0) Stage 2 of 5 (Device Configure) starting...
NetworkManager[2201]: <info> (enp38s0): device state change: prepare -> config (reason 'none') [40 50 0]
NetworkManager[2201]: <info> Activation (enp38s0) Stage 2 of 5 (Device Configure) successful.
NetworkManager[2201]: <info> Activation (enp38s0) Stage 3 of 5 (IP Configure Start) scheduled.
NetworkManager[2201]: <info> Activation (enp38s0) Stage 2 of 5 (Device Configure) complete.
NetworkManager[2201]: <info> Activation (enp38s0) Stage 3 of 5 (IP Configure Start) started...
NetworkManager[2201]: <info> (enp38s0): device state change: config -> ip-config (reason 'none') [50 70 0]
NetworkManager[2201]: <info> Activation (enp38s0) Beginning DHCPv4 transaction (timeout in 45 seconds)
dhcpcd[2262]: sending commands to master dhcpcd process
NetworkManager[2201]: <info> dhcpcd started with pid 2262
NetworkManager[2201]: <info> Activation (enp38s0) Beginning IP6 addrconf.
NetworkManager[2201]: <info> Activation (enp38s0) Stage 3 of 5 (IP Configure Start) complete.
NetworkManager[2201]: <info> (enp38s0): DHCPv4 client pid 2262 exited with status 0
NetworkManager[2201]: <info> Activation (enp38s0) Stage 4 of 5 (IPv4 Configure Timeout) scheduled...
NetworkManager[2201]: <info> Activation (enp38s0) Stage 4 of 5 (IPv4 Configure Timeout) started...
NetworkManager[2201]: <info> Activation (enp38s0) Stage 4 of 5 (IPv4 Configure Timeout) complete.
NetworkManager[2201]: <info> Activation (enp38s0) Stage 3 of 5 (IP Configure Start) starting DHCPv6 as requested by IPv6 router...
NetworkManager[2201]: <info> Activation (enp38s0) Beginning DHCPv6 transaction (timeout in 45 seconds)
NetworkManager[2201]: <warn> the dhcpcd backend does not support IPv6.
NetworkManager[2201]: <info> Activation (wlo1) starting connection 'MagnificentBumrag'
NetworkManager[2201]: <info> (wlo1): device state change: disconnected -> prepare (reason 'none') [30 40 0]
NetworkManager[2201]: <info> Activation (wlo1) Stage 1 of 5 (Device Prepare) scheduled...
NetworkManager[2201]: <info> Activation (wlo1) Stage 1 of 5 (Device Prepare) started...
NetworkManager[2201]: <info> Activation (wlo1) Stage 2 of 5 (Device Configure) scheduled...
NetworkManager[2201]: <info> Activation (wlo1) Stage 1 of 5 (Device Prepare) complete.
NetworkManager[2201]: <info> Activation (wlo1) Stage 2 of 5 (Device Configure) starting...
NetworkManager[2201]: <info> (wlo1): device state change: prepare -> config (reason 'none') [40 50 0]
NetworkManager[2201]: <info> Activation (wlo1/wireless): connection 'MagnificentBumrag' requires no security. No secrets needed.
NetworkManager[2201]: <info> Config: added 'ssid' value 'MagnificentBumrag'
NetworkManager[2201]: <info> Config: added 'scan_ssid' value '1'
NetworkManager[2201]: <info> Config: added 'key_mgmt' value 'NONE'
NetworkManager[2201]: <info> Activation (wlo1) Stage 2 of 5 (Device Configure) complete.
NetworkManager[2201]: <info> Config: set interface ap_scan to 1
NetworkManager[2201]: <info> (wlo1): supplicant interface state: inactive -> scanning
NetworkManager[2201]: <info> (wlo1): supplicant interface state: scanning -> authenticating
NetworkManager[2201]: <info> (wlo1): supplicant interface state: authenticating -> associating
NetworkManager[2201]: <info> (wlo1): supplicant interface state: associating -> completed
NetworkManager[2201]: <info> Activation (wlo1/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'MagnificentBumrag'.
NetworkManager[2201]: <info> Activation (wlo1) Stage 3 of 5 (IP Configure Start) scheduled.
NetworkManager[2201]: <info> Activation (wlo1) Stage 3 of 5 (IP Configure Start) started...
NetworkManager[2201]: <info> (wlo1): device state change: config -> ip-config (reason 'none') [50 70 0]
NetworkManager[2201]: <info> Activation (wlo1) Beginning DHCPv4 transaction (timeout in 45 seconds)
dhcpcd[2361]: sending commands to master dhcpcd process
NetworkManager[2201]: <info> dhcpcd started with pid 2361
NetworkManager[2201]: <info> Activation (wlo1) Stage 3 of 5 (IP Configure Start) complete.
NetworkManager[2201]: <info> (wlo1): DHCPv4 client pid 2361 exited with status 0
NetworkManager[2201]: <info> Activation (wlo1) Stage 4 of 5 (IPv4 Configure Timeout) scheduled...
NetworkManager[2201]: <info> Activation (wlo1) Stage 4 of 5 (IPv4 Configure Timeout) started...
NetworkManager[2201]: <info> (wlo1): device state change: ip-config -> failed (reason 'ip-config-unavailable') [70 120 5]
NetworkManager[2201]: <warn> Activation (wlo1) failed for connection 'MagnificentBumrag'
NetworkManager[2201]: <info> Activation (wlo1) Stage 4 of 5 (IPv4 Configure Timeout) complete.
NetworkManager[2201]: <info> (wlo1): device state change: failed -> disconnected (reason 'none') [120 30 0]
NetworkManager[2201]: <info> (wlo1): deactivating device (reason 'none') [0]
NetworkManager[2201]: <warn> Connection disconnected (reason -3)
NetworkManager[2201]: <info> (wlo1): supplicant interface state: completed -> disconnected
NetworkManager[2201]: <warn> Connection disconnected (reason -3)
I have run modprobe with the driver (ath9k) and it still won't work.
When connected to Wired, the internet works but it keeps saying 'Setting network address' without moving forward. When trying to connect to wireless it says 'Configuring interface' but then goes back to not connected.
Also, if I put Link-Local as the ipv4 method, it will connect successfully but then disconnect again. The (reasion 'ip-config-unavailable') pops up over and over again.
Also, I've tried wpa_supplicant, netctl, and wicd.Security questions
Read this note for information on how to reset the security questions http://support.apple.com/kb/HT5312
This user tip may also help you Security Questions -
hi im having problems with my internet and email Ive reset the network even with my WiFi on Ive also turned off and on airplane mode help please thank you
hi Ive reset my network toggled the airplane on and off and turned off my carrier off then turned my phone off and turned my carrier back on but still problem persists
-
I'm having problems with my email account. I receive emails when I'm in a wifi zone. But if the wifi is turned off and i'm not in a zone I don't receive my emails through the cellular network. Only when I power off the phone and turn it back on, do I receive the emails through the cellualr network (again with the wifi off)
In your email settings on the phone check to make sure it is set to receive emails on cellular network. It's a feature you can turn off so your phone isn't constantly updating emails on the cell network, but if you are usually in a place with wifi and aren't concerned about going over your data allowance, you can turn it back on.
-
I´m having problems with my wifi an my new Macbook pro. It doesn´t remember the network so every time I log on - I have to "join a network". I have "ticked" the "remember password" box. I´m connecting to a wireless network on an regular Speedtouch router at home. I´m new to Mackintosh.
Try the following, in order, until (hopefully) resolved:
1a. Delete Preferred Network(s)
System Preferences > Network > Wi-Fi > Advanced > Wi-Fi tab
Under "Preferred Networks," delete the network(s) you regularly use from the list.
1b. Delete AirPort Keychain Entries
Launch the "Keychain Access" application located in Applications/Utilties.
In the windows on the left side: Select login for Keychains and "All Items" for Category.
Click on the "Kind" filter at the top, and look for any "AirPort network password" entries...and delete them.
1c. Add Preferred Network(s)
System Preferences > Network > Wi-Fi > Advanced > Wi-Fi tab
Add the preferred network(s) using the "+" button.
Restart or log out then back in.
2. Move System Configuration Files
(Note: You will have to reestablish your network connections settings.)
Go to /Library/Preferences
Move the SystemConfiguration folder to the desktop.
Restart your Mac. (Note: OS X will rebuild the files that are now sitting on your desktop. If this doesn't resolve the issue, you can move the folder back to it's original location.) -
I am having problem with MDV Studio.
Hello happy guys, whatzup? Guess all ya 'r doing fine? Right!
I am using Dreamweaver from Macromedia Studio 2004. I am having problem with Inserting Record into Access database using the forms I create on my .asp document. I am using IIS and Javascript as my Document Technology. The error I usually have is:
"Technical Information (for support personnel)
Error Type:
Microsoft OLE DB Provider for ODBC Drivers (0x80004005)
[Microsoft][ODBC Microsoft Access Driver] Operation must use an updateable query.
/site_files/user_regform.asp, line 78
Browser Type:
Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US) AppleWebKit/530.5 (KHTML, like Gecko) Chrome/2.0.172.28 Safari/530.5
Page:
POST 41 bytes to /site_files/user_regform.asp
POST Data:
uname=Honesty&pword=admin&MM_insert=form1
Time:
Tuesday, June 02, 2009, 1:49:39 PM"
Please I need assistance on how to solve this problem. Thank you.
Similarly, I don't really know how to write sql strings - I just give commands and Dreamweaver will generate the sql strings. Yet, I still observe errors. But I think, for the sql aspect, I'm undergoing a tutorial note that I downloaded on the internet.
Please help me to solve this error problem at the moment. The sql knowledge is not the problem. I can get that at my leisure.
Thank you.
Eyo Eyo (Nigeria).It sounds like you do not have an internet connection (wifi arcs in the upper left does not mean you have a connection) since Safari does not work also.. Try the following:
- Reset the iPod. Nothing will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset networks settings: Settings>General>Reset>Reset Network Settings
- iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections -
I had already update mi new factory unlocked iPhone 4S to iOS 5.1.1 and I still having problems with "invalid sim". I'm from Argentina and here we don't have official service. PLEASE HELP ME, WHAT CAN I DO??? In Argentina is too expensive an iPhone 4S. Please I need help to continue believing in Apple. Thanks a lot. If anybody speak spanish better.
Was it purchased from an official Apple Store, not a reseller? Only Apple Stores sell official factory unlocked phones. The others sell hacked to unlock phones, and the unlocking is unstable.
Try these steps, as needed:
1. Reset phone - press both home and on/off buttons for at least 10 seconds until the Apple logo appears.
2. Settings > General > Reset > Reset Network Settings.
3. Replace SIM card (and reset network settings again)
4. Restore Phone in iTunes using a backup
5. Restore in iTunes as new, without using a backup -
Are you having problems with Windows XP Pro and Airport Utility Updates?
I was having problems with my wireless laptop setting up my Bonjour Printer. I checked to make sure I had downloaded the latest updates to Airport Utility and Bonjour. Check. After doing this I noticed I couldn't see my Airport Extreme through the Airport Utility. After much frustration and bringing my entire network crashing down around me, I got help from a knowledgeable guy from Cox Cable in San Diego. He helped me get my trusty iMac Power PC online. It saw my Airport Extreme but no answers were forthcoming in any forums about my XP issues. Here is what finally solved my problem. I uninstalled all Airport Utility and Bonjour Programs. I then went back to Airport Utility 5.3.1 for Windows. It installs Bonjour Printer services with this download. Everything is working perfectly again. I have my Canon Pixma MP500 connected to the USB port on my AEBS and Bonjour walked right through the setup process. I suggest that if this works for you, turn off all Airport Utility and AEBS firmware updates until you see that whatever issue Apple created with these updates gets fixed.
Well... it worked! :D
I'm pretty sure the extra 512 memory stick was the problem, that would explain why it was being inconsistent with its type of failures before. I'm going to reinstall it later and run memtest86 and try and see if i can get it to work at all somehow without causing problems, cuz 1.5 was already low enough...
DryHeat, yeah it was with SP2 but I got it installed now so no worries
Thanks a lot! -
Still having problems with VPN access
Hello!
I am having problems with my VPN clients getting access to the networks over a MPLS infrastruture. I can reach these resources form my Core network (172.17.1.0/24) and my Wifi (172.17.100.0/24) but not from my VPN network (172.17.200.0/24). From the VPN I can reach the Wifi network (which is behind a router) and the rule that allows that also allows access to the other networks but for some reason it is not working.
When I ping inside the core network from VPN I can connect and get responses. When I ping to the Wifi network, I can get responses and connect to resources there. A tracert to the wifi network shows it hitting the core switch (a 3750 stack) @ 172.17.1.1, then the Wifi router (172.17.1.3) and then the host. A tracert to a resource on the MPLS network from the VPN shows a single entry (the destination host) and then 29 time outs but will not ping that resource nor connect.
I've posted all the info I can think of below. Any help appreciated.
*** Here is a tracert from a core network machine to the resource we need on the MPLS:
C:\Windows\system32>tracert 10.2.0.125
Tracing route to **************** [10.2.0.125]
over a maximum of 30 hops:
1 1 ms <1 ms <1 ms 172.17.1.1
2 1 ms <1 ms <1 ms 172.17.1.10
3 5 ms 5 ms 5 ms 192.168.0.13
4 31 ms 30 ms 31 ms 192.168.0.5
5 29 ms 30 ms 29 ms 192.168.0.6
6 29 ms 29 ms 29 ms 192.168.20.4
7 29 ms 29 ms 29 ms RV-TPA-CRMPROD [10.2.0.125]
Trace complete.
172.17.1.10 is the mpls router.
**** Here is the routing table (sh ip route) from the 3750 @ 172.17.1.1
Gateway of last resort is 172.17.1.2 to network 0.0.0.0
S 192.168.30.0/24 [1/0] via 172.17.1.10
172.17.0.0/24 is subnetted, 3 subnets
S 172.17.200.0 [1/0] via 172.17.1.2
C 172.17.1.0 is directly connected, Vlan20
S 172.17.100.0 [1/0] via 172.17.1.3
172.18.0.0/24 is subnetted, 1 subnets
S 172.18.1.0 [1/0] via 172.17.1.10
S 192.168.11.0/24 [1/0] via 172.17.1.10
10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
S 10.2.0.0/24 [1/0] via 172.17.1.10
S 10.10.10.0/24 [1/0] via 172.17.1.10
S 10.20.0.0/24 [1/0] via 172.17.1.10
S 10.3.0.128/25 [1/0] via 172.17.1.10
S 192.168.1.0/24 [1/0] via 172.17.1.10
S* 0.0.0.0/0 [1/0] via 172.17.1.2
*** Here is the firewall config (5510):
ASA Version 8.4(1)
hostname RVGW
domain-name ************
enable password b5aqRk/6.KRmypWW encrypted
passwd 1ems91jznlfZHhfU encrypted
names
interface Ethernet0/0
nameif Outside
security-level 10
ip address 5.29.79.10 255.255.255.248
interface Ethernet0/1
nameif Inside
security-level 100
ip address 172.17.1.2 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 172.19.1.1 255.255.255.0
management-only
banner login RedV GW
ftp mode passive
dns server-group DefaultDNS
domain-name RedVector.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network WiFi
subnet 172.17.100.0 255.255.255.0
description WiFi
object network inside-net
subnet 172.17.1.0 255.255.255.0
object network NOSPAM
host 172.17.1.60
object network BH2
host 172.17.1.60
object network EX2
host 172.17.1.61
description Internal Exchange / Outbound SMTP
object network Mail2
host 5.29.79.11
description Ext EX2
object network NETWORK_OBJ_172.17.1.240_28
subnet 172.17.1.240 255.255.255.240
object network NETWORK_OBJ_172.17.200.0_24
subnet 172.17.200.0 255.255.255.0
object network VPN-CLIENT
subnet 172.17.200.0 255.255.255.0
object-group service DM_INLINE_TCP_1 tcp
port-object eq www
port-object eq https
object-group network DM_INLINE_NETWORK_1
network-object object BH2
network-object object NOSPAM
object-group network VPN-CLIENT-PAT-SOURCE
description VPN-CLIENT-PAT-SOURCE
network-object object VPN-CLIENT
object-group network LAN-NETWORKS
network-object 10.10.10.0 255.255.255.0
network-object 10.2.0.0 255.255.255.0
network-object 10.3.0.0 255.255.255.0
network-object 172.17.100.0 255.255.255.0
network-object 172.18.1.0 255.255.255.0
network-object 192.168.1.0 255.255.255.0
network-object 192.168.11.0 255.255.255.0
network-object 192.168.30.0 255.255.255.0
object-group network VPN-POOL
network-object 172.17.200.0 255.255.255.0
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
access-list Outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq smtp
access-list Outside_access_in extended permit tcp any object BH2 object-group DM_INLINE_TCP_1
access-list global_mpc extended permit ip any any
access-list Inside_access_in extended permit object-group DM_INLINE_PROTOCOL_1 any any
pager lines 24
logging enable
logging asdm informational
no logging message 106015
no logging message 313001
no logging message 313008
no logging message 106023
no logging message 710003
no logging message 106100
no logging message 302015
no logging message 302014
no logging message 302013
no logging message 302018
no logging message 302017
no logging message 302016
no logging message 302021
no logging message 302020
flow-export destination Inside 172.17.1.52 9996
mtu Outside 1500
mtu Inside 1500
mtu management 1500
ip local pool VPN 172.17.1.240-172.17.1.250 mask 255.255.255.0
ip local pool VPN2 172.17.200.100-172.17.200.200 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (Inside,Outside) source static EX2 Mail2
nat (Inside,Outside) source static any any destination static NETWORK_OBJ_172.17.1.240_28 NETWORK_OBJ_172.17.1.240_28
nat (Inside,Outside) source static any any destination static NETWORK_OBJ_172.17.200.0_24 NETWORK_OBJ_172.17.200.0_24
nat (Inside,Outside) source static inside-net inside-net destination static NETWORK_OBJ_172.17.1.240_28 NETWORK_OBJ_172.17.1.240_28
nat (Inside,Outside) source static LAN-NETWORKS LAN-NETWORKS destination static VPN-POOL VPN-POOL
object network inside-net
nat (Inside,Outside) dynamic interface
object network NOSPAM
nat (Inside,Outside) static 5.29.79.12
nat (Outside,Outside) after-auto source dynamic VPN-CLIENT-PAT-SOURCE interface
access-group Outside_access_in in interface Outside
access-group Inside_access_in in interface Inside
route Outside 0.0.0.0 0.0.0.0 5.29.79.9 1
route Inside 10.2.0.0 255.255.255.0 172.17.1.1 1
route Inside 10.3.0.0 255.255.255.128 172.17.1.1 1
route Inside 10.10.10.0 255.255.255.0 172.17.1.1 1
route Inside 172.17.100.0 255.255.255.0 172.17.1.3 1
route Inside 172.18.1.0 255.255.255.0 172.17.1.1 1
route Inside 192.168.1.0 255.255.255.0 172.17.1.1 1
route Inside 192.168.11.0 255.255.255.0 172.17.1.1 1
route Inside 192.168.30.0 255.255.255.0 172.17.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server RedVec protocol ldap
aaa-server RedVec (Inside) host 172.17.1.41
ldap-base-dn DC=adrs1,DC=net
ldap-group-base-dn DC=adrs,DC=net
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *****
ldap-login-dn CN=Hanna\, Roger,OU=Humans,OU=WPLAdministrator,DC=adrs1,DC=net
server-type microsoft
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 172.17.1.0 255.255.255.0 Inside
http 24.32.208.223 255.255.255.255 Outside
snmp-server host Inside 172.17.1.52 community *****
snmp-server location Server Room 3010
snmp-server contact Roger Hanna
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Outside_map interface Outside
crypto ikev1 enable Outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
telnet 172.17.1.0 255.255.255.0 Inside
telnet timeout 5
ssh 172.17.1.0 255.255.255.0 Inside
ssh timeout 5
console timeout 0
dhcpd address 172.17.1.100-172.17.1.200 Inside
dhcpd dns 172.17.1.41 172.17.1.42 interface Inside
dhcpd lease 100000 interface Inside
dhcpd domain adrs1.net interface Inside
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
webvpn
group-policy RedV internal
group-policy RedV attributes
wins-server value 172.17.1.41
dns-server value 172.17.1.41 172.17.1.42
vpn-tunnel-protocol ikev1
default-domain value ADRS1.NET
group-policy RedV_1 internal
group-policy RedV_1 attributes
wins-server value 172.17.1.41
dns-server value 172.17.1.41 172.17.1.42
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
default-domain value adrs1.net
username rparker password FnbvAdOZxk4r40E5 encrypted privilege 15
username rparker attributes
vpn-group-policy RedV
username mhale password 2reWKpsLC5em3o1P encrypted privilege 0
username mhale attributes
vpn-group-policy RedV
username dcoletto password g53yRiEqpcYkSyYS encrypted privilege 0
username dcoletto attributes
vpn-group-policy RedV
username rhanna password Pd3E3vqnGmV84Ds2 encrypted privilege 15
username rhanna attributes
vpn-group-policy RedV
tunnel-group RedV type remote-access
tunnel-group RedV general-attributes
address-pool VPN2
authentication-server-group RedVec
default-group-policy RedV
tunnel-group RedV ipsec-attributes
ikev1 pre-shared-key *****
class-map global-class
match access-list global_mpc
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
class global-class
flow-export event-type all destination 172.17.1.52
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
hpm topN enable
Cryptochecksum:202ad58ba009fb24cbd119ed6d7237a9Hi Roger,
I bet you already checked it, but does the MPLS end router has route to VPN client subnet 172.17.200.x (or default) pointing to core rtr)?
Also, if the MPLS link has any /30 subnet assigned, you may need to include that as well in Object group LAN-NETWORKS.
Thx
MS -
Hi, I have an Iphone 3g that is "Not" jailbroken, nor do I want it to be jailbroken. However, I had been having problems with it shuting down and not starting again. So, I tried to update and restore only to get an "error" 1015.
It is now stuck on "connect to itunes"
Any help would be great as this is a factory unlocked phoneApple in no way blocks devices.
Carriers can blacklist devices from their network. If that is what has occurred, only the carrier can remove the blacklist. This should have nothing to do with your ability to activate the device and use it as an iPod. -
Indesign CS6 on MACs with OS 10.8 are having problems with links
Hi
Indesign CS6 on MACs with 10.8 are having problems with links. All links to other files have to be updated when opening a file although definitely nothing has changed to the linked files.
We can rule out our company's networking and the system hosting the files (HELIOS software on RedHat Linux VM). This happens with newly created Indesign files and with old ones. E.g. we create a file on Tuesday, save it and open it again on the exact same MAC on Wednesday and all links to other fiels (.indd, .png, .bmp, etc. nothing uncommon) have to be updated as they all show the yellow triangle + black exclamation mark symbol next to them. Has anybody else experienced this, What can we do? We have tried absolutley everything and updated all software from MAC OS to CS6 itself but nothing seems to help on the long run.
Any further information required?
M. MillerThanks for your quick reply.
We actually noticed that there also seems to be something wrong with the timestamps:
If we open the infos via the MAC finder to a file (.psd e.g.) which is linked in one of our indesign files, it states a certain date of creation.
If we then switch to the Indesign file we just opened in which we had to update all links and open the infos to exactly the same file we looked at in the finder, a different date of creation is stated. So there also seems to be a mistake here (hope it's clear what I mean).
We are ruling out our network as the error cannot be "re-enacted". We have created numerous test files in Indesign (simple white page containing one link to a .psd file which is also used in one of the supposedly defective files) and have opened them on various MACs with various OS versions over the past days/weeks but unfortunately the files open without any notifications or errors.
Just as a background: a few months ago, the problem seemed to occur between MACs with differing OS, 10.6 - 10.8 at first. A file which was created on a 10.6 MAC could not be opened without updating all links on a 10.8 MAC. That is why we updated everything to 10.8. The error did not occur for about 2-3 weeks but then reoccured again.?
Have you heard anything similar? -
Hi all. I recently restore my old iphone 5 on my new 6. I'm having problems with bluetooth devices. The ones that were already paired with the old one are not showing in the list, and most of them(not all) are not working or pairing. I already restored network settings to no avail. Any ideas?
What's more, they don't even show on the bluetooth devices list..
-
I am having problems with the Ipad accepting my password in the secure mode in Wifi. I can get into wifi when the secure mode is off. This only started when I downloaded the lastest update for the Ipad. Anyone else having the same problems? I have rebooted the Rotar and still doesn't work.
I am not.
Which secure mode are you using with your wireless network - WEP or WPA?
Have you tried forgetting this network on your iPad, and/or resetting network settings on your iPad? Both will require rejoining the network and the latter will require rejoining every wi-fi network your iPad has access to when returning within range of the network. -
Windows 8.1 having problems with pinter selection using Elements 13.
I am running Windows 8.1 with Elements 13 and am having problems with PRINT. If I select a printer from the PRINTER menu, Elements recognizes the change of selection, allows me to modify the printer's specific setting and, then, when I PRINT seems to not recognize the selected printer and print of whatever was set as the original printer. Then, I delete the "original" printer in Windows 8.1 and attempt to print again with the same general result except I receive a Printer Not Found error from Windows.
How do I modify the "original" printer setting (seems to be associated with the file)? Note the "original" printer is not the default printer.Hatstead,
Thank you.
Yes, all of the print drivers are up to date (re-verified last evening).
Yes, I can print and select the printer as normal for all of the standard applications I use (Visio, PowerPoint, Word, Excel, Outlook, direct print from file (Explorer)).
I shortened the printer names from the standard Microsoft convention (based on some of the BOG comments). There was no change. In fact after the test sequence noted in #5, I re-implemented the "name shortening" yet again (shorter yet). I launched Elements and ran into the same messages noted in #5 (obviously, the "stored" printer did not exist). Yet after I went through the printer selection process (again as in #5) and, after a lag time, Elements redirected the print job what was the "stored" printer which was renamed....I do not know how Elements associated the deleted "Stored" printer with its old name with the newly named printer since no other application could (I checked).
I have closed and restarted the PC numerous times.
I have deleted all of the printers except the one I wanted to use for the specific print job. In this case, Elements came back with a message it could not access the "stored" printer. I then selected the correct printer, Elements acted like it was allowing to set up the selected printer with the specifics of the print job, and, then when I went to print, Elements again tried to redirect the print job to the "stored" printer (even though it did not exist).
The target printer is a "local" printer (USB connected). The apparent "Stored" printer is a network printer. So, I deleted the PC which has the "Stored" printer from the network (actually not only deleted it from the devices on my PC but literally shut the PC down and disconnected it from the network (two different test)) to no avail (still got the test results in #5).
Yes, I have attempted to print from the Editor (my normal mode) and from Organizer.
I have copied, open a new file and, then, pasted the image I wanted to print to no avail.
Is the a "stored" printer associated with the file or with Elements? If so, how to I modify (or dis-associate)?
Again, thank you. -
Facing problems with network due which the phone goes into hangs status
Facing problems with network due which the phone goes into hangs status. some one help me with switching between 2g and 3G network
Hi Mani Nair,
I apologize, I'm a bit unclear on the exact nature of the issue you are describing. If you are talking about having issues with a 3G cellular data network, you may find the troubleshooting steps outlined in the following article helpful:
iPhone cellular data connection issues
Regards,
- Brenden
Maybe you are looking for
-
Error: InfoObject does not contain alpha-conforming value 20030729
Hi everyone, I got this problem, that i tried to fix yesterday, but all i did was that i got realy frustrated... I created an infoobject which is copy of 0DOC_NUMBER and has alpha coversion routine. Mapping field in DataSource is also type character
-
After 2.1 update Eris will not leave POP mail on server
I've seen some other posts on this, at least one of which said Verizon has acknowledged as a 2.1 issue - but it's not clear if any solution has yet been provided. Since the 2.1 update, if I delete my Verizon e-mail on my Eris it's evidently deleting
-
Compile fine in Netbeans, won't execute
After I compile my file in netbeans, i try to run it and get this error: java.lang.NoClassDefFoundError: Game/src/game/Main (wrong name: src/game/Main) at java.lang.ClassLoader.defineClass1(Native Method) at java.lang.ClassLoader.defineClass(ClassLoa
-
I downloaded the new update for IOS 5.1 for my iphone 3GS but it accidentally got unplugged so i had to restore it. However when the update finished, it would nto let me restore my phone and sync my previous apps, videos, and music etc. back onto my
-
A MDM Scenario Regarding accessing and displaying data
Hi All, If there is a scenario such that there is a Manufacturer field from Main table[ Products ], has some vaues say A, B, C, etc. A suppose belongs to India, B to USA, C to UK, etc respectively. Then how can we do this that if a user is assigned t