Having t510 usb problems

hello,
We having t510 thin client usb problems its doesn't come up as anothe drive.
Carl

Hi
Can you expand on what your asking . Does the USB have anything on it ?? I assume it's a flash stick ???
Checkurtech
****Click the White Kudos star to say thanks****
****Please mark Accept As Solution if it solves your problem****

Similar Messages

MS-6389E USB problem

I am having intermittent usb problems for no apparent reason my usb mouse stops working until i unplug and replug it back into the board i am on bios ver 5.7 anyone have any ideas how to fix this?

Do you have other USB devices? Only the mouse? Check your Device Manager (Control Panel) to see if your USB controllers are installled and working properly. And please, post your system specs!

USB problems since EFI firmware update 2.6

My MBA has been suffering USB problems since this update.
I have an IOGear USB 3 GUH374 hub. I connect my iPad mini and USB 3 disk to it.
Since the update, the iPad has stopped charging through the hub. Now, I can't find the power specs of the hub, so I don't know that it should work, but it was working fine. Now, the iPad says "not charging".
The USB disk has spontaneously disconnected a few times, with the system reporting that it was improperly disconnected. One time, the disk was corrupted.
This could be a coincidence, so I've contacted IOGear. But, I'm also having new, different, sleep problems with the MBA and Mountain Lion.
==Leonard

Sitongia
This is a user community, it is not Apple.
If you wish to thank Apple, here is the feedback link for iPad.
http://www.apple.com/feedback/ipad.html

MAC PRO USB Problem - Traced to bad Apple Keyboard Extension Cable

I found a fix to a problem synching to my itunes Library on my early 2008 MAC PRO. The Apple supplied USB extension cable for the keyboard was defective.
The symptoms were hangs in itunes and finder synching to iPods and transferring data to USB hard drives. The iPods and hard drives never lost power and no errors/log entries were made. The transfers simply stalled and would not continue. itunes and finder would hang until the drive or ipod was removed. These devices were installed directly to USB ports on the MAC PRO. No other USB devices were connected except for the aluminum keyboard and mighty mouse; the mouse was connected to the keyboard. The keyboard was connected using the USB extension cable that shipped with the MAC PRO.
Hardware diagnostics were all clear. The keyboard and mouse never had any connection problems. Only itunes syncs and hard drive copies would fail; these would occur at random times. I had an open ticket with Apple to have the logic board replaced as it was diagnosed to be a hardware/USB problem.
Removal or replacement of the extension cable on the keyboard (which was connected to a different USB port and NOT in the USB chain with the ipod and hard drives) permanently fixed the problem. I cancelled the Apple HW replacement.
I have noted several posts with others having problems with USB ports and devices. I wonder if Apple has an unknown problem with bad keyboard extension cables.

I think you may be onto something there. I'm just a few weeks into my second Mac Pro and again it's having the same USB problems which led Apple to give me a replacement machine previously. I went through several weeks of considerable testing with Apple Engineers prior to that - an Apple Care application to collect data from my machine, Apple Developer USB prober and two clean installs. The latest machine initially showed no sign of the problem then it started again - 2 iPods "can not be read or written to" part way through sync, Aperture quitting importing from USB SD card reader, USB drives dismounting etc. So I pulled out the Aluminium keyboard and, lo and behold, the iPods managed to get all the way through synching without errors. I really like the alu keyboard so it's a huge shame that it might be the cause of all my problems so far - and the Mac Pro is otherwise a beautiful computer.
But is this really a hardware problem of the internal USB cards and power management or supply?

N8 belle USB problems

hey.. just updated my n8 to belle..
im having a really hard time whenever i connect my usb to the computer as mass storage or ovi suite..
whenever i connect my phone to the pc.. i can barely use my phone.. no apps or anything plus its very slow ( i dont remember having this kind of problem with the older versions).
then after i disconnect it.. my phone always freezes completely.. i have to do a hard reset everytime i connect it to the pc which is really annoying..
any1 else here having the same problem?

@philvio69
Something certainly not right here and strange that device hangs irrespective of whether in Nokia/Ovi Suite or mass storage mode(s) as you would stop the latter via taskbar before removing device.
Have you tried connecting your N8 as a Windows USB mass storage device to another PC just to confirm this behaviour?
Happy to have helped forum with a Support Ratio = 42.5

MS-6390: Return Of The USB Problem!

Almost a year ago I posted a thread regarding a USB problem in which after a few hours runtime, the USB ports stop working. Having reinstalled Windows, I followed the original thread to fix the problem again but this time, it hasn't work. The old thread for reference is; https://forum-en.msi.com/index.php?topic=49727.0
but I shall try and include everything important here so it shouldn't be needed.
Firstly the nature of the problem;
Any new device plugged into them is not recognisied and Windows advises that it is the device that is malfunctioning.
Restarting the computer will eliminate the problem, however upon rebooting, the computer tends to get stuck at what may be the memory count. If left for 10 minutes, the memory amount comes up and the computer boots normally. This is circumvented by temporarily (one second) removing power to the power supply by pulling the plug or flicking the switch at the back.
[It may or may not be relevant that the HDD activity indicator is lit for approximately 30 seconds of this 10 minute period]
Upon switching the computer on again, the computer boots up normally and the USB ports continue to function for another variable period of time.
This problem occurs if there are no devices plugged into the USB, any single device (printer, gamepad, mobile phone) or any combination.
It should also be noted that if the computer crashes due to any of many unrelated reasons after this problem has arisen, and I use the reset button to make it reboot, the 10 minute reboot problem occurs again but appears differently on screen in that it actually says 'memory check' or words to that effect with a space where the normally RAM amount goes, a '+' and another empty space where the memory reserved for onboard graphics normally goes (i.e. memory check: + )
I've tried uninstalling the drivers and reinstalling those downloaded from VIAs website for my chipset.
My USB ports are set not to power down to save power in device manager.
The multi-card reader (plugged directly into the motherboard) also stops functioning when the USB ports go down - power light stays on, activity light stops flashing (occasionally power light turns off). Unplugging it from the motherboard does not resolve the issue.
I want to resolve this issue so the computer is trouble-free when I give it my mum to learn from.
Comp. specs in signature. Thanks in advance.

I don't know how to dig deeper... Soon this computer will only be using a single 80 gig HD, and I'll remove the fan controller (it'll be mums computer). I'll then be able to try just using sp1a.
This PSU I'm using is reviewed here with a several others. (the model number is the same, but the one tested doesn't appear to be dual rail - they actually state the number slightly incorrectly, but it's correct in the picture of the label they show.
I think it performed quite well, being one of only two that were able to keep producing (just) over 1 v at 100% load, whilst most others just plumetted. A significant but probably not damaging drop to 4.87v on the 5v rail and again 3.26 on the 3.3v rail all at 100% load (which you're never supposed to due to the PSU anyway). It got a recommended award since apparently it doesn't have many features but I don't think I'm in need of any features it lacks.
Furthermore - at the back it has a control for fan speed. Currently set on Auto, it maintains the same fan speeds (audiability) as on Low - thus I conclude it has headroom to push itself if necessary (in which case the fans would spin faster).
Apart from someone who said they're "cheapo", I havn't yet found any negative comments regarding Jeantech PSUs.

Shuffle USB Problem - Some Observations

I decided to start a new thread with some additional observations I have made regarding the Shuffle and USB problems. Some of this already appeared as a reply to the "ipod usb" thread. Anyway recapping from my previous post:
When plugged into the USB port of my machine, the front LEDs (above the control area) flash the following:
GREEN and ORANGE (YELLOW?) flash together for between 1/4 and 1/2 second. This is followed by the GREEN LED alone for about 1.5 seconds. 3 seconds of nothing, then it repeats. The battery condition LED on the back (below the ON/OFF switch blinks ORANGE for about 1/4 second every 4 seconds.
Plugging the Shuffle into another computer (a laptop), the Shuffle is recognized and the LEDs behave normally.
Now the weird thing is that the Shuffle had worked on the machine where it is now not recognized. In fact the iTunes 7.0.1 diagnostics show the serial number of the Shuffle as the last iPod connected. Also, the USB on the iTunes machine is a USB 1.0 and on the laptop is USB 2.0.
NEW OBSERVATIONS:
My 20GB Click Wheel iPod works fine under 7.0.1. The fact that it works leads me to believe the USB port and power are fine. If it the USB port can drive a hard disk iPod, it better be able to drive a Shuffle!
I loaded up the version of iTunes that came with the Shuffle on another Windows 2000 box I have. The Shuffle was recognized and did a RESTORE on it. Windows even recognized it. The version of Windows IS NOT as currently patched as the computer on which I have iTunes 7.0.1 installed.
I uninstalled iTunes 7.0.1 and installed version 6.0. Aside from 6.o not starting because some file got converted, Win2000 still did not recognize the Shuffle.
So here are my thoughts:
1) A recent Windows 2000 patch causes Shuffles to be ignored by the OS. There is a comment about a problem like this with XP, but I was not able to find anything Win2000 related. The machine I am having problems with is up to dat with regard to patches.
2) If V7.0.01 is the problem, even uninstalling it and reinstalling an old version of iTunes leaves some part of the driver or something that still causes problems.
3) The Phillips Pronto remote software I installed somehow causes a bad interaction with only the Shuffle. Remember, my click wheel iPod still works!
Right now I am leaning towards an issue specific to Windows2000 and the Shuffle. Maybe a conspiracy to get us all to buy Zunes?
If anyone has additional observations or suggestions on how to fix the problem, I (and a bunch of other people) would really like to hear from you.
Thanks!
Don

Okay, I got focused on the fact that other machines
would recognize my Shuffle, but not my main machine.
It dawned on me that the Windows Registry stores
information about USB devices whether or not they
are plugged in, so I snooped around and found the
entries for the iPod.
I did some searches and found a reference to this MS
KB article:
http://support.microsoft.com/kb/315539/en-us
Basically describes how to show the "hidden" (i.e.
removed USB) devices. Went into the USB section and
deleted the 2 entries I had for iPods (my Shuffle and
20GB click wheel).
Plugged my Shuffle in and BINGO! Windows recognized
the Shuffle and iTunes 7.0.1 recognized the Shuffle!
In fact, as I write this post, my poor little
Shuffle is having my jogging play list reinstalled
since it got wacked by the 'restore' on the other
machine.
Bottom line, it looks like I managed to solve my
green and orange LEDs of death problem!
Your mileage may vary!
Good luck!
Don
Yes, great, this is a fix for this problem. Thank you very much.
Athlon Windows XP

Frustratingly, since I upgraded to Yosemite 10.10, I too am having the worst problems with WiFi dropping out. I've never had this problem before on my iMac 27-inch mid 2011 model. Turning WiFi off and then back on again sometimes works. Help please.

Frustratingly, since I upgraded to Yosemite 10.10, I too am having the worst problems with WiFi dropping out. I've never had this problem before on my iMac 27-inch mid 2011 model. Turning WiFi off and then back on again sometimes works. Help please. I've already tried a lot of your suggested fixes, but without success. Why hasn't Apple Fixed this?

Please test after taking each of the following steps that you haven't already tried. Stop when the problem is resolved. Back up all data before making any changes.
Step 1
Take the applicable steps in this support article. The Wireless Diagnostics program generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
Step 2
Disconnect all USB 3 devices. If you don't know which are USB 3, disconnect all USB devices except keyboard and mouse.
Step 3
If you're not using a wireless keyboard or trackpad, disable Bluetooth by selecting Turn Bluetooth Off from the menu with the Bluetooth icon. If you don't have that menu, open the Bluetooth preference pane in System Preferences and check the box marked Show Bluetooth in menu bar. Test. If you find that Wi-Fi works better with Bluetooth disabled, you should use the 5 GHz Wi-Fi band. Your router may not support it; in that case, you need a new router.
Step 4
Open the Energy Saver pane in System Preferences and unlock the settings, if necessary. Select the Power Adapter tab, if there is one. Uncheck the box marked
Wake for Wi-Fi network access
if it's checked.
Step 5
Open the Network pane in System Preferences and make a note of your settings in the Wi-Fi service. It may be helpful to take screenshots of the various tabs in the preference pane. If the preference pane is locked, unlock it by clicking the padlock icon and entering your administrator password. Delete Wi-Fi from the service list on the left by selecting it and clicking the minus-sign button at the bottom. Then recreate the service by clicking the plus-sign button and following the prompts.
Step 6
In the Wi-Fi settings, select
Advanced... ▹ TCP/IP ▹ Configure IPv6: Link-local
Click OK and then Apply.
Step 7
Reset the System Management Controller.
Step 8
Reset the PRAM.
Step 9
Launch the Keychain Access application. Search for and delete all AirPort network password items that refer to the network. Make a note of the password first.
Step 10
Make a "Genius" appointment at an Apple Store, or go to another authorized service center.

L505D-LS5001 no audio / no usb problem

i been having problems with my audio and usb drive, allready try installing drivers and nothing..
the audio tells me no audio output installed.
and the usb and sd card slot wont work eider. runnning windows 7 32bit , audio driver is microsoft audio highdefiniton with the yellow (!)
when i try to install laptops drivers go to the best drivers allready install.
usb problem i really dont know whats the problem..Laptop still on warranty.
Any help please

I have run into this same issue; it seems to occur that in device manager, no USB host is even present. Audio just has a red "X" on it.
I've tried installing the drivers, updates.
I restored from the Restore discs from Toshiba (which just crash)
I've done an install from a straight WIn7 X64 disc (which works, but then Red "X")
I've tried changing memory, HDD..
I've tried bootable LInux, which also doesn't see a USB controller.
This is very annoying. This seems to have happened after someone flashed the 1.10 BIOS onto this (I have an L505D-LS5007)
Something here is very amiss, and a laptop with no USB, no Audio is almost worthless. It's as though the BIOS control for the southbridge is wrong. I've tried re-flashing with 1.10, no difference.. I'd love to be able to rollback to 1.00, but I can't even find it.

Garageband opens now -- but USB problem

Applemeisters-- I just posted a note about how my Garageband won't open. Googled and found the problem. You must have the correct date operating on your computer or it won't work. I live in the Chicago burbs and, as a result of having power out for several days, the date on my computer system was off by that number of days. Corected that and Garageband is live again.
Now, about the USB problem. Please help. An Ion turntable that works fine with the regular stereo console, But when I plug it directly into my G4 tower with an OS 10.2.8 system and record lps into the audacity software the sound sounds miserable on the speakers while recording and miserable after I transfer the recording into a MP3. Is Ion supposed to be a plug and play for Apple or does it just work for PCs? What's a guy to do? Help. Thanks.
Paul

This is only a guess, because I've not got HK USB speakers: But maybe the master volume in GB is up too high. Take it right down and then turn up your speakers, see if that does it.

790GX G65 Firewire and USB problem

I've m-audio firewire 410 sound card and cubase5 (has a usb dongle to work)
before this mainboard I was using K9A2 platinium V2 and Amd 9950 cpu everything was working perfectly
now I've upgraded my board (as you see) and bought a AMD 955
now when I install the sound card driver it's making somekind of digital distortion and also the sound is moving to faster or slower (all the time) so I'M hearing funny voices
The Cubase5 Usb dongle is having some connection problem. It force me to change the usb port everytime I start cubase
I've updated my bios but guess what.... They're still with me.
Please some help
I'm using Vista home premium 32, I've tried it on Xp and windows 7 64 RC7100 the resoult is always the same

Quote from: Bas on 19-July-09, 16:39:47
Are the energy settings properly configured for USB and the CPU?
Could be Cubase doesn't like Cool & Quite?
Can Cubase work with quad-core?
Can the powersupply handle everything?
What is in your system, we don't know much: >>Posting Guide<<
Read the guide this time.
My system is
MSI 790GX G65 , AMD 955 BE, Corsair 1600 MHZ 4 GB (TW3X4G1600C9D) , 6 HDD (one is IDE), ZOTAX 9800 GTX+, 750 watt PSU(corsair TX750W)
I've some pci card for my music buss. but i didn't install them yet. Not before everything works fine
Cubase works fine with quad core , my ex-system was a quad core.
the problem with cubase comes this way. I turn on the pc (dongle is on all the time) start cubase and get the message "Connection problem with dongle change the usb port) after I change it everthing works fine. infact I'm not making cubase problem a big deal. my real problem is firewire.
About the energy settings, I didn't change anything on mainboard, why do I need to change the power settings for usb? aren't they standart?

Virtualbox USB problem.

Hey everyone,
Just got myself a Tomtom ease, and i'm trying to connect it to the Tomtom Home app under windows xp running in Virtualbox 3.2.6.
When I plug the device in thunar automounts it.
It shows up as a usb device in my virtualbox menu, but is greyed out.
I unmount it in thunar and it is still greyed out in virtualbox.
I have also tried "umount /media/INTERNAL" and still, no luck in virtualbox.
Anybody know of any solution to this problem?
Thank You.

empthollow wrote:I remember having a similar problem with my mp3 player, I can't remember for sure what I did but I think it had something to do with pluging the device in before or after virtualbox was running. I thought it was after otherwise it would gray out (I deduce) because linux recognized it first?... Also make sure you are not using the OSE version. USB is not enabled. Hope that helps, best of luck.
That was my initial thought as well, as I have had the problem with my ipod.
I have not yet used my ipod or the new tom tom under virtualbox with my latest Arch build however, and the solutions you've suggested don't work this time around.
Thank you for the input though.

I'm having a real problem with my cursor which seems to have developed a mind of its own, zigzagging allover, highlighting things without my command, and basically making my MacBook unuseable (it's taken me half an hour just to compose this!).

I'm having a real problem with my cursor which seems to have developed a mind of its own, zigzagging allover, highlighting things without my command, and basically making my MacBook unusable (it's taken me half an hour just to compose this!).

There are several possible causes for this issue. Please take each of the following steps that you haven't already tried until it's resolved. Some may not apply in your case.
1. Follow the instructions in this support article, and also this one, if applicable. A damaged or defective AC adapter could be the cause, even if it's the right kind.
2. Press down all four corners of the trackpad at once and release. If there's any effect, it's likely to be temporary, and in that case the unit must be serviced or replaced.
3. Open the Bluetooth preference pane in System Preferences and delete all pointing devices other than the trackpad, if applicable. Disconnect any USB pointing devices. By a "pointing device," I mean a peripheral that moves the cursor, such as a trackpad, mouse, trackball, or graphics tablet. A plain keyboard is not a pointing device.
4. Start up in safe mode and test, preferably without launching any third-party applications. If you don't have the problem in safe mode, but it comes back when you restart as usual, stop here and post your results. Do the same if you can't start in safe mode. If there was no difference in safe mode, go on to the next step.
5. Reset the System Management Controller.
6. If you're using a Bluetooth trackpad or mouse, investigate potential sources of interference, including USB 3 devices.
7. A swollen battery in a portable computer can impinge on the trackpad from below and cause erratic behavior. If you have trouble clicking the trackpad, this is likely the reason. The battery must be replaced without delay.
8. There's a report that a (possibly defective) Thunderbolt Ethernet adapter can cause the built-in trackpad of a MacBook to behave erratically. If you're using such an adapter, disconnect it and test.
9. There's also a report of erratic cursor movements caused by an external display that was connected but not turned on.
10. If none of the above applies, or if you have another reason to think that your computer is being remotely controlled, remove it from the network by turning off Wi-Fi (or your Wi-Fi access point), disconnecting from a Bluetooth network link, and unplugging the Ethernet cable or USB modem, whichever is applicable. If the cursor movements stop at once, you should suspect an intrusion.
11. Make a "Genius" appointment at an Apple Store to have the machine and/or external trackpad tested.

Very stranae usb problem!! K8N NEO2-FX

Hello all
I am having some really strange usb problems
Things that work:
my sandisk memory stick usb reader fine,
most cheap mp3 players (Not all tho)
my sony camera lead works,
game pads fine,
crucial 512 flash pen fine
Things that dont work:
my sons sandisk usb card reader microSD wont work
Cosair 4 gb wont work(that Pi**ed me off).
Nokia 6300,Samsung J600,Samsung D900I,Nokia 5300.
When i put things in usb ports onboard or case it asks for the driver for the device.Then says there is a problem with the install and the device can be used.
I have re-wired the case as per case and MB manuals,i flashed to 1.D.Have tried all the nforce drivers out there!!Its just so random why will it use some usb thing and not others??
Thanks in advance to any and all help given.

Yes
Sorry its XP PRO SP2 installed as well.
The motherboard driver is currently
Version: 5.11
Release Date: November 2, 2005
WHQL Certified
Installation Notes
Windows XP users must install Service Pack 1, at a minimum, prior to attempting to install this package. Failure to do so will result in the inability to support USB 2.0.
Installation of DirectX 9.0 or higher is required in order to use NVMixer.
Release Notes
General compatibility fixes for nForce3 motherboards
Driver Versions
Audio driver version 4.42 (WHQL)
Audio utility version 4.44
Win2K ethernet driver version 4.16 (WHQL)
WinXP ethernet driver version 4.16 (WHQL)
Ethernet NRM driver version 4.82 (WHQL)
Network management tools version 4.88
GART driver version 4.36 (WHQL)
Memory controller driver version 3.38 (WHQL)
SMBus driver version 4.04 (WHQL)
Installer version 4.46
IDE driver version 4.46 (WHQL)

FISR2 USB problems

I have a K8T Neo FISR2 mobo and am experiencing some strange USB problems. I have a DLink 7 port USB2.0 hub with a few things attached to it. That is the only usb item directly hooked up to my PC. When I first start up the machine, about 50% of the time the usb doesn't seem to be connect to the hub. The green lights go on as the PC boots, but once it gets into Windows, they go out and nothing appears connected. If I unplug the hub and plug it back in again, I can usually get the PC to recognize the hub and the devices connected to it. I have tried moving the hub to different ports on the PC and re-installing the drivers, but neither of those seem to fix the problem.
Any ideas?
Ryan

Because I like having the USB ports accessible as opposed to moving the PC everytime I want to remove or add a device.
Plus it doesn't really make a difference. I had a friends external USB hard drive hooked up directly to the back and XP didn't recognize that either.
It's almost like XP is shutting off the USB ports.

Having t510 usb problems

Similar Messages

Maybe you are looking for