Having trouble setting my airport extreme for guests

hi having trouble setting my airport extreme for guests?

Please see your other post on exactly the same subject.

Similar Messages

Hi having trouble setting my airport extreme for guests?

hi having trouble setting my airport extreme for guests?

This is likely because you have the AirPort Extreme connected to a modem/router, or gateway device.....and not a simple modem. Can you provide the make and model number of your "modem", as we previously asked?

Having trouble setting up Airport Extreme Base Sation

Hi,
I'm new to a wireless set up for my Mac.
Initially I tried to set up entering various passwords along the way and discovered my cables were not connected correctly - I rectified this and tried again.
I was then encouraged to proceed via Bridge mode which I did and eventually got a confirmation that set up was complete. However my light on the Airport Extreme went from solid green to a slow amber flash and I was made aware of 2 problems by AirPort utility 1) Your Apple Wi-Fi base station does not have a valid IP address 2) This Apple Wi-Fi base station doesn't have any DNS server addresses and might have trouble connecting to the internet
Despite this I am connected wirelessly to the internet and so wondered how, or if I need to, solve these two problems?
Thanks for any help on this

Update
I skipped the problems and updated anyway - It then came back with the 2nd problem and a few moments later said this was resolved. I still had amber light but after starting AirPort Utility a couple of times I eventually got a solid green light and no reported problems.

How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

Having trouble using my airport extreme as a media server for my ps3--can anyone help?

I'd like to set up my apple airport extreme with a USB seagate drive, and use the drive as a media server for my ps3. I have successfully connected my seagate drive to my airport extreme. I have successfully transferred a sample movie to this seagate drive. My laptop is easily able to find the drive and is able to play the sample film from the drive. How can I turn this drive into a media server? I'd like for my PS3 to be able to read movies off the network drive and play them. Help??

Welcome to the discussions, DanSwiggsD!
If you have a non-Apple device as your main router, unfortunately the AirPort Extreme has almost no chance of compatibility with your main router.
If you do have an Apple router as your main device, please post back with your model number and we'll let you know how your devices should be configured.
If you don't have an Apple device as your main router you have a few options to connect the xbox:
1) A pair of ethernet powerline adapters could be used if you did not want to run a regular ethernet cable from your main router to the xbox.
2) The new AirPort Express 802.11n model does have a feature called Proxy STA which should allow it to receive a wireless signal from any wireless router and allow the ethernet port to be enabled.
Message was edited by: Bob Timmons

Can I set up Airport Extreme for wireless printiing over Uverse network?

I previously had DSL, and used my Airport Extreme as my wireless router. It was in my home office, so my printer was directly plugged into the Base Station. I recently switched to ATT Uverse, which came with its own wireless router. The new router is in another room, next to the TV. My question is this: Can I set up my old AEBS to function as a wireless printing outpost, like an Airport Express, that would be connected to my office printer but accessed through the ATT network? Thanks.

Welcome to the discussions, Patrick!
Can I set up my old AEBS to function as a wireless printing outpost, like an Airport Express, that would be connected to my office printer but accessed through the ATT network?
In theory, yes. In practice, this is one of those things that you won't know until you try. Since the AEBS will have to "join" your ATT wireless network, the biggest question will be whether or not you can find a matching security setting on the AEBS for the ATT wireless network.
Are you able to get into the setup pages on the ATT router to see exactly what type of security is being used? Ideally, it will be WPA2 Personal, but different manufacturers use different names and flavors for the same thing, so it's rarely as easy as one might hope when you try to get devices from two manufacturers to talk to each other over wireless.

Trouble setting up Airport Extreme Card to allow Internet Sharing

Hi,
I just recently purchased a Mac Mini with the Airport Extreme Card, and was able to manage to get it to work to share my Internet connection with my husband's Airport enabled iBook G3...for a few days, and now it appears that the network I created is no longer available.
For the record, I find setting all of this up to be really confusing, and suspect that some of my difficulty lies in not fully understanding what I'm doing as I'm doing it, which makes it hard for me to troubleshoot what's going on.
I've tried using the Airport Utility v5.4.2, but it says it's unable to find any wireless devices, and all the menu options are grayed out.
As always, thanks in advance for any light you can shed on my difficulties.

Duane,
Thanks, that's exactly what I did last week, and it was working for a few days and then for some reason stopped working. However, today, I went into the System Preferences, turned Internet Sharing off and then back on again, and it appears to be working once again.
When you say that's not as reliable a service, I guess my problem is an example of that? With a standalone router (I take it you mean a true Extreme Base Station), what are the advantages? I can't afford to purchase one of those at the moment, but might consider it somewhere down the line.
Nicole

Setting Up AirPort Extreme for Static IP

We purchased a new AirPort Extreme about a month ago. It was very easy to set up and worked very well for all of the devices in our home, with the exception of VPN connections on our work laptops. These were incredibly slow (taking 20-30 minutes to open large spreadsheets, etc.). We talked to our ISP (4G satellite connection) about this, and they recommended going to a static IP. I have used the AirPort Utility to enter the IP address, sub net mass, router address and DNS numbers, and the AirPort indicates everything is set up properly (green status light, no errors in AirPort Utility), but it will no connect. Looking at the Internet Connection through AirPort Utility, it has all the correct numbers but the connection says "disconnected". I am able to establish an ethernet connection directly from the modem to a computer and connect with no issues. And the ISP has confirmed that the modem is working properly.
What am I missing to get the connection throughb to my AirPort Extreme?
Thanks for any help and suggestions you can provide.

Hi..
I have this same question.
Yes i did change all those and have tried with all the possible settings.
Still the problem persists..It shows all the configuration and all is right and still it is not connecting to internet.
Cross checked with the ISP, Tried same configuration in the mac machine(It's working) everything else seems to be fine but only the Airport is not connecting to the Internet.
Any solution or clarification will be appreciated.
Thanks in Advance.

Setting up airport Extreme for Remote Printing

I'm leaving town and need to be able to print to our work printer (HP LJ 1320 connected via Ethernet to AirPort Extreme 802.11n).
I also want to set up our home printer (HP LJ 1022 connected to Time Capsule via USB).
I've spent hours trying everything I can think of - changed AirPort settings, have desktops sharing printers - nothing works.
I have no problem connecting to computers over the internet - using screen sharing with ease. I am at a loss as to why printing is such a problem. any help will be hugely appreciated!

I did open those ports on my AirPorts.
I've tried setting up the printers as LPD and IPP as well as HP JetDirect - Socket, but despite pointing my print jobs at these, nothing has worked yet.
Is the Airport going to act as a print server - or is that just part of the printer? Is a server even necessary? It isn't when I'm on site with either printer.
good luck with your set-up. thanks for your input.

Having trouble setting up home network for home sharing

Hi there, I'm new the idea of home sharing. What i want to do is watch the movies that i have on my iMac on my iPad. So sort of like wireless streaming.
I see that Home sharing on iTunes allows you to view videos stored on your iMac on another device like the iPad etc.
I've already setup Home sharing accounts and looged in on iTunes on both my iMac and iPad.
The problem is being on the same Wi-Fi network. I don't understand what this means.
I regualrly use Internet sharing to share my Macs internet connection with my iPad over WiFi.
But I'm not sure what setting I should use for home sharing to work to watch videos from iMac on iPad
On my iMac under Sharing there's a whole bunch of options DVD or CD sharing, File Sharing, Printer Sharing etc.
The only box i have checked is Internet Sharing..
What to i have to do to get the iMac and iPad sharing video over WiFi through home sharing??

In your configuration you have inadvertently created a different subnet for the wireless iMac G5. To remedy this, configure the AirPort Express so that the option to distribute IP addresses is DISABLED.

Can I reset my AirPort Extreme by pushing the tiny reset button on back of the unit (I am having trouble setting it up) I read that pushing the little button will reset to factory settings?

I am having trouble setting up my new AirPort Extreme. I think I have it all hacked up. Can I push the reset button on the back of the unit and reset to the factory settings and start over?

this should help: Resetting an AirPort base station FAQ
What used to be called a "hard reset" on earlier models is now called a "factory default reset" on 802.11ac models, so things can get confusing. At least Apples seems to have updated the FAQ recently to reflect the changes with the new models.....if you dig deep enough.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

HT201250 I am having trouble setting up my time capsule. the amber light is flashing. i have a Verizon FIOS network that i use for the internet (WiFi) and do not want to configure the Time Capsule to do that function. I just want the Time Capsule to ba

I am having trouble setting up my time capsule. the amber light is flashing. i have a Verizon FIOS network that i use for the internet (WiFi) and do not want to configure the Time Capsule to do that function. I just want the Time Capsule to back up.

Simple.. bridge the TC.. in the apple utility in the NAT and DHCP area.
Plug it into the FIOS router.. you can turn off wireless in the TC if you want.. or use it.. it can work faster if you are nearby and can select 5ghz.. but up to you.

I am having trouble setting up my Yahoo! e-mail account on my phone...it asks for my Password and I type it in correctly and, carefully, but I get an error window, "MF Message Error Domain error 1032" -what does thi smean and how can I get around it?

I am having trouble setting up my Yahoo! e-mail account on my phone...it asks for my Password and I type it in carefully and correctly, but I get an error window, "MF Message Error Domain error 1032" -what does this mean and how can I get around it? My password is long and convoluted, but it works when I type it in on my main Mac workstation, just fine.....what gives?

try restarting the phone and try again

HT204053 I am having trouble setting up icloud on MAC. In system preference it is listed as mobile me, it asks for member name and password. It also has a learn more button under "try mobileme for free". I am not getting anywhere

I am having trouble setting up icloud on MAC. In system preference it is listed as mobile me, it asks for member name and password. It also has a learn more button under "try mobileme for free". I am not getting anywhere

It's evident that you are using Snow Leopard or earlier (or very early Lion) since you have the now obsolete MobileMe preference pane.
The minimum requirement for iCloud is Lion 10.7.5 (Mountain Lion preferred): the iCloud Preference Pane does not appear on earlier systems - the MobileMe pane appears on Lion and earlier but is non non-functional - you cannot now open or access a MobileMe account.
To make use of iCloud you will have to upgrade your Mac to Lion or Mavericks, provided it meets the requirements.
The requirements for Lion are:
Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7, or Xeon processor
2GB of memory
OS X v10.6.6 or later (v10.6.8 recommended)
7GB of available space
Lion is available in the Online Apple Store ($19.99). Mountain Lion (10.8.x) is also available there at the same price but there seems little point as the system requirements are the same for Mavericks (10.9.x) - which is free - unless you need to run specific software which will run on Mountain Lion only.
The requirements for Mountain Lion and Mavericks are:
OS X v10.6.8 or later
2GB of memory
8GB of available space
and the supported models are:
iMac (Mid 2007 or newer)
MacBook (Late 2008 Aluminum, or Early 2009 or newer)
MacBook Pro (Mid/Late 2007 or newer)
Xserve (Early 2009)
MacBook Air (Late 2008 or newer)
Mac mini (Early 2009 or newer)
Mac Pro (Early 2008 or newer)
It is available from the Mac App Store (in Applications).
You should be aware that PPC programs (such as AppleWorks) will not run on Lion or above; and some other applications may not be compatible - there is a useful compatibility checklist at http://roaringapps.com/apps:table
If you are running Leopard on an Intel Mac you will have to upgrade to Snow Leopard to access the Mac App Store - it's available in the online Apple Store. However if you have a PPC Mac you cannot run Snow Leopard and cannot proceed further.

Having trouble setting my airport extreme for guests

Similar Messages

Maybe you are looking for