Having upgraded to yosemite on iMac it now takes ages to but up
why is it since upgrading to Yosemite on my iMac it now takes ages to start up when using the start button?
Different OS, different start up/boot up time. Yes, Yosemite does have a slower boot up even on the fastest Macs. The good news is that Yosemite restarts are faster than the boot up time.
Similar Messages
-
i am trying to upgrade to yosemite (for imac) from version 10.6.8 but even though i have 70gb available on my hard drive it wont let me upgrade because it says i dont have enough memory!! what can i do??
Install more RAM in the computer; the Mac needs to have at least 2GB of RAM and should have 4GB or more first.
(125734) -
Since i upgraded to Yosemite, my iMac is too slow
Since i upgraded to Yosemite, my iMac is too slow. For example, at the starting up, it needs minutes 34" to open.
When i open a window / folder, i need between 1 and 2 minutes. By opening a pdf or an other document i uses 2 to 7 minutes.
WHY? How can i change this?1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Fonts 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB 'com.adobe.AAM.Updater-1.0 com.adobe.AAM.Updater-1.0 com.adobe.AdobeCreativeCloud com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.adobe.SwitchBoard com.apple.aelwriter com.apple.AirPortBaseStationAgent com.apple.FolderActions.enabled com.apple.installer.osmessagetracing com.apple.mrt.uiagent com.apple.ReportCrash.Self com.apple.rpmuxd com.apple.SafariNotificationAgent com.apple.usbmuxd com.citrixonline.GoToMeeting.G2MUpdate com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper com.oracle.java.JavaUpdateHelper org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.startx' '879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 3694147963 1233118628 2456546649 2806998573 2778718105 2636415542 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 523110921 2883943871 3873345487' 51 5120 files 4 );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[46]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<10) print "com.apple.";} ' ' { sub(/ :/,"");print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p ' '/^root$/p' ' !/^\/[AD]|\/Contents\/.+\/Contents\//&&/\/(Lib|usr).+\/(.+\.framework|Contents|Info\.plist|Resources|Versions)$/ { n++;sub(/\/Info\.plist$/,"");sub(/\/(Content|Resource|Version)s(\/.+)?/,"");print|"sort|uniq";} END { if(n<1100) print "/System/";} ' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /^\/[AD]/d;p;' 's/Pr.+n //p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&& $3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\\([0-9]+\\)\\(.+\\)/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"cksum "F|getline C;split(C, A);C="checksum "A[1];"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("PlistBuddy -c Print "F|getline g) { l++;if(l<=L) f=f"\n "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F" ("T", "C")";else F=F" ("C")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;' ' s/^.+ |\(.+\)$//g;p ' '/\.(appex|pluginkit)\/Contents\/Info\.plist$/p' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END { if(i>1) print n;} ' ' s/:[^:]+$//;s/ +([0-9]+)(.+)/\2 x\1/p;' ' { gsub(/[()"]/,"",$3);if(!$3) $3="N/A";print $3;} ' ' /es: ./{ s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/\n.+//p;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin /' ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' pluginkit scutil dtrace profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e netstat mdls );S1() { printf kMDItemContentTypeTree=com.apple.$1'|sort';};S2() { printf 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :'$1'" {} \;|uniq';};c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" "`S2 CFBundleDisplayName`" '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '-F \$Message -k Sender kernel -k Message CSeq "I/O e"|sort|uniq -c' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$(RefProc): \$Message' -k Sender Req 'fsev|kern|launchd' -k RefProc Rne 'Aq|WebK' -k Message Rne '08012|Goog|ksadm|probe|Roame|SMC:|smcD|sserti|suhel| VALI|ver-r|xpma' -k Message Req 'abn|bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|idle ex|inval|jnl:|last value [1-9]|NVDA\(|pagin|pci pa|proc: t|Roamed|rror|SL|TCON|Throttli|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' "`S1 bundle`" "`S1 mach-o-dylib`" `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????|wc -l' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' " -F '\$Time \$Message' -k Sender kernel -k Message CSeq 'n Cause: -' " -i '-app Safari UserStyleSheetEnabled' -name\ kMDItem${p[35]} "`S2 ${p[35]}`" );N1=${#c2[@]};for j in {0..10};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files I/O\ errors 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors App\ extensions Lockfiles Memory\ pressure SMC Shutdowns Nets Stylesheet );N3=${#l[@]};for i in {0..3};do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};A'$((7+i))'() { v=` eval sudo "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};';done;A9(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2 7 8;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 0 $((N1+8)) 71 $((N3+3));D13 1 10 7 9;D13 1 11 8 10;B1&&D73 19 53 67 55;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D13 5 5 69 1;D13 5 54 30 56;D23 5 14 12 14;D22 6 36 13 15;D22 20 52 66 54;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D82 35 49 61 51;D82 11 17 17 20;for i in 0 1;do D82 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A8 18 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 24 22 29;B7 12;B2 14;A4 39 57 70 14;B2 15;B6 14 15 4;C3 29;A1 24 23 32;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 26 50 64;B7 16;C3 52;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D73 21 0 32 19;D73 10 42 32 40;D82 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+10)) 51 32;D13 4 8 41 6;D12 21 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 38 55 68 57;D23 33 34 42 37;B1&&D83 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 10 42 32 41;D13 37 2 48 43;A1 4 3 60;B2 30;A1 4 58 60;B2 31;B6 30 31 4;C3 5;D12 21 56 35 58;D12 21 48 49 49;B3 4 22 57;A1 21 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D12 4 51 32 53;D23 22 9 37 7;A9;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
After upgrading to Yosemite my IMac Hangs
After upgrading to Yosemite my IMac will hang usually on a given App and I have to force a power down and reboot to get it back in operation.
Anyone else having this problem?russellfrompalm desert wrote:
I've checked the App Store, no updates available. However, McSoltaire isn't listed
in the available solitaire apps.
Do you think I should download/buy new solitaire & hearts apps?
Did you get McSolitaire from the Mac App Store, if not it would not be available there. You should contact the developer to see if they have any updates or you can also look in MacUpdates.com -
After upgrading to Yosemite, my MacBook Pro now requires me to enter a password whenever I start up my computer. I want to eliminate this step and to go back to the ability to reboot and begin using without a login. How do I accomplish this?
Hightlight Login Option. This will bring up the window showing Automatic login.
Please post a pic of your window if Automatic login is missing. Make sure your personal info is not showing. -
I just upgraded to Yosemite. Iphoto is now broken. Upon upgrade receiving error "This update is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled."
Perform the following, stopping with the first one which works:
1. Open the Mac App Store's Purchases tab. If you're prompted to accept iPhoto into your Apple ID, do so.
2. Move it out of the Applications folder(it may need to be put into the Trash temporarily), and then see if you can download it for free from its individual product page.
3. Click here and contact Apple.
(116137) -
Having downloaded Mavericks to my IMac two weeks ago, I now find Time Machine couldn't back up to the Time Machine HDD. I am using a WD 1TB External Hard drive. I understand that a number of people have lost data since installing Mavericks on their Western Digital external drives. Has anyone any futher info. Or is there a better way of backing up my computer. Thanks. Lee
Check the More Like This section at the right particularly i upgraded my imac hard drive to a 2tb drive. how do i use time machine to get my computer back to normal?
-
iMac running Mountain Lion.... Yesterday, I tried to upgrade to Yosemite. System seemed to be upgrading. However, the OSX installation window is now frozen on the computer with the blue bar showing installation complete. I do not have access to even the finder. Force quitting with keys is not working. The only way I can shut the computer down is to hold down the on/off button. Restarting brings up the same frozen OSX installation window. What to do?
CherieThere are three ways:
A. Reinstalling Yosemite, Mavericks, Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
B. Install or Reinstall from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
the Security button and set the Zero Data option to one-pass. Click on
the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall Yosemite: Select Reinstall OS X and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless.
C. Internet Recovery
Install OS X Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall Yosemite: Select Reinstall OS X and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
This should restore the version of OS X originally pre-installed on the computer. -
Upgraded to Lion on iMac. Now HDMI output is gone.
I have an iMac connected through HDMI to my Sony Bravia. It's worked fine.
After I upgraded to Lion, I went to display from iMac to the TV and my HDMI selection under Preferences is now gone.Copy protection Is getting “tighter”.
The Intel-developed technology is called High-bandwidth Digital Content Protection (HDCP) and aims to prevent copying of digital audio and video content as it travels across a variety of display connectors (like HDMI), even if such copying is not in violation of fair use laws.
Among the connectors supported by the technology are HDMI and the Mini DisplayPort found on Apple's latest MacBook, MacBook Pro, and MacBook Air, in addition to others such as Digital Visual Interface (DVI), High-Definition Multimedia Interface (HDMI), Gigabit Video Interface (GVIF), and Unified Display Interface (UDI).
Presently, I do not know of a “workaround”. -
Upgraded to Firefox 24 and now nothing at all works despite uninstalling and reinstalling it several times and losing all my bookmarks etc. However it does start in safe mode. At first I thought it was my security Norton 360 but after 2 hours in contact with them I'm still in the same position. When I double click on the Firefox icon I can see the cursor timing out and then it just disappears and nothing loads.
My OS is Windows Vista Premium and I am using Windows internet explorer at the moment.
HELP please!!!Sometimes a problem with Firefox may be a result of malware installed on your computer, that you may not be aware of.
You can try these free programs to scan for malware, which work with your existing antivirus software:
* [http://www.microsoft.com/security/scanner/default.aspx Microsoft Safety Scanner]
* [http://www.malwarebytes.org/products/malwarebytes_free/ MalwareBytes' Anti-Malware]
* [http://support.kaspersky.com/faq/?qid=208283363 TDSSKiller - AntiRootkit Utility]
* [http://www.surfright.nl/en/hitmanpro/ Hitman Pro]
* [http://www.eset.com/us/online-scanner/ ESET Online Scanner]
[http://windows.microsoft.com/MSE Microsoft Security Essentials] is a good permanent antivirus for Windows 7/Vista/XP if you don't already have one.
Further information can be found in the [[Troubleshoot Firefox issues caused by malware]] article.
Did this fix your problems? Please report back to us! -
Upgraded to Yosemite from Mt.Lion, now my MacMini is extremely slow
After installing Yosemite my Mini runs horribly slow. It takes 3 minutes to open Safari, several minutes to open a new page and forget about streaming anything...Is there a way to go back to a previous OS? This is truly disappointing and unacceptable. Glad I didn't jump in and upgrade my MacBook Air too.
Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
Then download and install the OS X Yosemite 10.10.3 Combo Update.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless.
5. Reinstall Yosemite from Scratch:
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
How to Clean Install OS X Yosemite.
Then download and install the OS X Yosemite 10.10.3 Combo Update.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless. -
Having upgraded to lion my imac drops the internet connect when not active
I have just upgraded to Lion and when I leave the computer unattended for a few minutes it drops its internet connection - therefore does not collect any email until I click on the Airport icon and reselect the network. Also when starting up the and automatically loading Firefox the home page shows the previous download.
I FINALLY SOLVED THIS ISSUE!!!!
New routers have "mixed" modes for your network; this means that it will automatically choose the best option between wireless-B, wireless-G and wireless-N network modes. I used to experience this issue using the 2.4 GHz. mixed mode wireless network.
Thankfully, my router can create 2 networks: a 2.4 GHz. network and a 5 GHz. network.
When I randomly changed this value to "use only wireless-B and wireless-G" trying to fix an issue with a wi-fi expander, the iMac wi-fi issue dissapeared! I tried it with wireless-N only, but it didn't work.
So, finally, I have a 2.4 GHz network with only wireless-B and wireless-G modes which works PERFECT with the iMac, and a 5 GHz. network with a mixed* wireless mode for everything else mode.
*PD: by "mixed" mode it means that the router will automatically choose between B, G and N network modes as it fits better. -
I Went to the store to upgrade phones and get a new plan. They didn't have any of the three phones I was gettin, Tried to sell me a plan for 8 gigabyte, even though we don't even use 1 now. Left mad, manager watched and did nothing. Tried to call, I got mad when the customer service agent chuckled at me. I was pretty well done then. Wife tried, had it all worked, we were getting the arrangements as we wanted them. I even listened since it was on speaker phone, she was still talking as she left the house, the Verizon phone dropped the call, she called back and now they won't us the same deal they already agreed to. I told her I would try one last time. I explai this was my last call, at the end I found that my plan is paid through the 21st. What is really bad is that they don't even care enough to have a supervisor call. They won't even let me speak to one. I was willing to stay with them because in the past I had never had a problem with them, now I can see how they could be any worse.
Kccustomer wrote:
mrhelper, you sure are knowledgeable about Verizon, the $30 fee is the cost to upgrade one of my phone. I feel that this is unreasonable since I do not have a contract and a new customer does not have to pay that.
The only time you pay the upgrade fee is if you take a subsidized discount on a phone and that does in fact require a contract. new customers have to pay a $35 activation fee.
As far as me being knowledgeable this fee has been in place for 2 1/2 and was announced on every major news source and is CLEARLY labeled on each phone in the stores and online. In fact my local store has a huge sign right at the counter stating that all upgrades are assessed a $30 upgrade fee. So know it doesn't take a lot of knowledge to know this fee exists. -
Problem: this mac is not reading an excell file after upgrading to yosemite. My Mac is from 2009, it use to work perfectly but it wasn´t able to open some apps, thats why i upgrade it. Now it once i donwload the zip it appears with an ".ods" extension
i even already download a link
http://www.microsoft.com/en-us/download/confirmation.aspx?id=44026
which i read on another support page... but it doesnt allowed me to install it cause it says that i already have the disk of this program....
Im afraid to erase it and not being able to get it back...
What can i do!??
Thanks in advance for this kind answer!!!fsolution wrote:
Problem: this mac is not reading an excell file after upgrading to yosemite... Now it once i donwload the zip it appears with an ".ods" extension...
If the "it" refers to a compressed (zipped) spreadsheet that you downloaded, the ".ods" extension is used by LibreOffice and probably OpenOffice (which are free versions of MS Office) for spreadsheets, which would suggest that wherever you're getting that "Excel" file from has switched to one of those programs. I've tried opening an .ods file from LibreOffice using MS Office 2013 for Windows and it does open though with a warning that some things have been changed. I don't know if Office for Mac can normally open .ods files. But if your need is to just open .ods files, take a look at LibreOffice. -
After upgrading Yosemite my imac become very slow in power off!!!
Hello, i have this problem: after upgrading to yosemite my imac (27" 8gb intel i5) become very very slow in power off!!
Every other function are ok...only power off is very slow!!
I try to reinstall, to exit from iCloud, verify permission of disk and clean with application like ccleaner...but the problem remain!!
Anyone have my same problem? How can i fix this?
Thanks to all.Uninstall Avast and CleanMyMac2.
Avast Un-install
You do not need to use cleaning programs. They can destroy your computer operation as they may already have done.
CleanMyMac - Uninstall
CleanMyMac2 Un-install
After un-installing, run this program to make sure you got all the pieces.
EasyFind – Spotlight Replacement
Activity Monitor - Mavericks also Yosemite
Activity Monitor in Mavericks has significant changes
Performance Guide
Why is my computer slow
Why your Mac runs slower than it should
Slow Mac After Mavericks
Things you can do to resolve slowdowns see post by Kappy
Maybe you are looking for
-
I bought my macbook about 6 years ago and I also have a first generation iPod Touch. The version of iTunes I have on my macbook is out of date for the iPad2 I just purchased. What is the easiest way i can get my iTunes upgraded so that I can connect
-
Hi Gurus, In ALV grid display, I have 'display' and 'print' icon in the application tool bar. When I select a particular record and click display buttton, it will display the detailed description of the particular row.but, when i select the print bu
-
Xpath, node absolute path and Remote Events for XML (REX)
Folks, No question here, just a solution to share. I want to implement Remote Events for XML (REX) in Actionscript 3. Outgoing rex events require that I find an absolute xpath expression for my XML DOM nodes that have changes. Incoming rex events req
-
I am not too computer savvy. Can someone help me into getting to play DVDs on iPad 2 16gb
-
Two artists under one album cover
There is two albums on my itouch that the songs from two artists have been added to each others playlists. I open the music folder select the artist then the album and everything seems ok but when I select a song then look at now playing and tap the